Re: [RFC PATCH net-next v2 1/1] net: Support for switch port configuration

[B Viswanath]

On 19 December 2014 at 14:53, Jiri Pirko <jiri@xxxxxxxxxxx> wrote:
> Fri, Dec 19, 2014 at 10:01:46AM CET, marichika4@xxxxxxxxx wrote:
>>On 19 December 2014 at 13:57, Jiri Pirko <jiri@xxxxxxxxxxx> wrote:
>>> Fri, Dec 19, 2014 at 06:14:57AM CET, marichika4@xxxxxxxxx wrote:
>>>>On 19 December 2014 at 05:18, Roopa Prabhu <roopa@xxxxxxxxxxxxxxxxxxx> wrote:
>>>>> On 12/18/14, 3:26 PM, Samudrala, Sridhar wrote:
>><snipped for ease of reading>
>>>>>>
>>>>>>
>>>>>> We also need an interface to set per-switch attributes. Can this work?
>>>>>>     bridge link set dev sw0 sw_attr bcast_flooding 1 master
>>>>>> where sw0 is a bridge representing the hardware switch.
>>>>>
>>>>>
>>>>> Not today. We discussed this @ LPC, and one way to do this would be to have
>>>>> a device
>>>>> representing the switch asic. This is in the works.
>>>>
>>>>
>>>>Can I assume that on  platforms which house more than one asic (say
>>>>two 24 port asics, interconnected via a 10G link or equivalent, to get
>>>>a 48 port 'switch') , the 'rocker' driver (or similar) should expose
>>>>them as a single set of ports, and not as two 'switch ports' ?
>>>
>>> Well that really depends on particular implementation and drivers. If you
>>> have 2 pci-e devices, I think you should expose them as 2 entities. For
>>> sure, you can have the driver to do the masking for you. I don't believe
>>> that is correct though.
>>>
>>
>>In a platform that houses two asic chips, IMO, the user is still
>>expected to manage the router as a single entity. The configuration
>>being applied on both asic devices need to be matching if not
>>identical, and may not be conflicting. The FDB is to be synchronized
>>so that (offloaded) switching can happen across the asics. Some of
>>this stuff is asic specific anyway. Another example is that of the
>>learning. The (hardware) learning can't be enabled on one asic, while
>>being disabled on another one. The general use cases I have seen are
>>all involving managing the 'router' as a single entity.  That the
>>'router' is implemented with two asics instead of a single asic (with
>>more ports) is to be treated as an implementation detail.  This is the
>>usual router management method that exists today.
>>
>>I hope I make sense.
>>
>>So I am trying to figure out what this single entity that will be used
>>from a user perspective. It can be a bridge, but our bridges are more
>>802.1q bridges. We can use the 'self' mode, but then it means that it
>>should reflect the entire port count, and not just an asic.
>>
>>So I was trying to deduce that in our switchdevice model, the best bet
>>would be to leave the unification to the driver (i.e., to project the
>>multiple physical asics as a single virtual switch device). Thist
>
> Is it possible to have the asic as just single one? Or is it possible to
> connect asics being multiple chips maybe from multiple vendors together?

I didn't understand the first question. Some times, it is possible to
have a single asic replace two, but its a cost factor, and others that
are involved.

AFAIK, the answer to the second question is a No. Two asics from
different vendors may not be connected together. The interconnect
tends to be proprietary.

> I believe that answer is "yes" in both cases. Making two separate asics
> to appear as one for user is not correct in my opinion. Driver should
> not do such masking. It is unclean, unextendable.
>

I am only looking for a single management entity. I am not thinking it
needs to be at driver level. I am not sure of  any other option apart
from creating a 'switchdev' that Roopa was mentioning.

>
>>allows any 'switch' level configurations to the bridge in 'self' mode.
>>
>>And  then we would need to consider stacking. Stacking differs from
>>this multi-asic scenario since  there would be multiple CPU involved.
>>
>>Thanks
>>Vissu
>>
>>>>
>>>>>
>>>>>
>>>>> --
>>>>> To unsubscribe from this list: send the line "unsubscribe netdev" in
>>>>> the body of a message to majordomo@xxxxxxxxxxxxxxx
>>>>> More majordomo info at  http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/