[PATCH] printk: add per console loglevel
From: dwalker
Date: Sat Dec 20 2014 - 17:52:23 EST
This adds to to the console= command line options allowing the
addition of a per console log level setting.
examples,
console=ttyS0,ll4
console=tty0,ll6
This can be used on systems which have multiple serial consoles, but
it's desired for logging to be light on one and heavy on another.
Signed-off-by: Daniel Walker <dwalker@xxxxxxxxxx>
---
Documentation/kernel-parameters.txt | 24 ++++++++++++++++++------
include/linux/console.h | 1 +
kernel/printk/console_cmdline.h | 9 +++++----
kernel/printk/printk.c | 37 ++++++++++++++++++++++++++++++++++++-
4 files changed, 60 insertions(+), 11 deletions(-)
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 4df73da..7e65d5b 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -696,30 +696,42 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
console= [KNL] Output console device and options.
- tty<n> Use the virtual console device <n>.
+ tty<n>[,llX] Use the virtual console device <n>.
- ttyS<n>[,options]
- ttyUSB0[,options]
+ ttyS<n>[,options][,llX]
+ ttyUSB0[,options][,llX]
Use the specified serial port. The options are of
the form "bbbbpnf", where "bbbb" is the baud rate,
"p" is parity ("n", "o", or "e"), "n" is number of
bits, and "f" is flow control ("r" for RTS or
omit it). Default is "9600n8".
+ "llX" explained below,
+
See Documentation/serial-console.txt for more
information. See
Documentation/networking/netconsole.txt for an
alternative.
- uart[8250],io,<addr>[,options]
- uart[8250],mmio,<addr>[,options]
+ uart[8250],io,<addr>[,options][,llX]
+ uart[8250],mmio,<addr>[,options][,llX]
Start an early, polled-mode console on the 8250/16550
UART at the specified I/O port or MMIO address,
switching to the matching ttyS device later. The
options are the same as for ttyS, above.
- hvc<n> Use the hypervisor console device <n>. This is for
+
+ "llX" explained below,
+
+ hvc<n>[,llX]
+ Use the hypervisor console device <n>. This is for
both Xen and PowerPC hypervisors.
+ "llX" is used to define the loglevel per console. The "X"
+ defines the loglevel number for this console. The usage
+ is similar to the "loglevel=" option, and the effect is
+ the same only per console. The "loglevel=" option takes
+ precedence of this option.
+
If the device connected to the port is not a TTY but a braille
device, prepend "brl," before the device type, for instance
console=brl,ttyS0
diff --git a/include/linux/console.h b/include/linux/console.h
index 7571a16..99020d5 100644
--- a/include/linux/console.h
+++ b/include/linux/console.h
@@ -118,6 +118,7 @@ static inline int con_debug_leave(void)
struct console {
char name[16];
+ int loglevel;
void (*write)(struct console *, const char *, unsigned);
int (*read)(struct console *, char *, unsigned);
struct tty_driver *(*device)(struct console *, int *);
diff --git a/kernel/printk/console_cmdline.h b/kernel/printk/console_cmdline.h
index cbd69d8..6f6f98f 100644
--- a/kernel/printk/console_cmdline.h
+++ b/kernel/printk/console_cmdline.h
@@ -3,11 +3,12 @@
struct console_cmdline
{
- char name[8]; /* Name of the driver */
- int index; /* Minor dev. to use */
- char *options; /* Options for the driver */
+ char name[8]; /* Name of the driver */
+ int index; /* Minor dev. to use */
+ int loglevel; /* Log level for this console */
+ char *options; /* Options for the driver */
#ifdef CONFIG_A11Y_BRAILLE_CONSOLE
- char *brl_options; /* Options for braille driver */
+ char *brl_options; /* Options for braille driver */
#endif
};
diff --git a/kernel/printk/printk.c b/kernel/printk/printk.c
index 02d6b6d..218d94d 100644
--- a/kernel/printk/printk.c
+++ b/kernel/printk/printk.c
@@ -1414,6 +1414,9 @@ static void call_console_drivers(int level, const char *text, size_t len)
if (!cpu_online(smp_processor_id()) &&
!(con->flags & CON_ANYTIME))
continue;
+ if (con->loglevel && !ignore_loglevel &&
+ level >= con->loglevel)
+ continue;
con->write(con, text, len);
}
}
@@ -1925,6 +1928,33 @@ asmlinkage __visible void early_printk(const char *fmt, ...)
}
#endif
+
+char *setup_per_console_loglevel(struct console_cmdline *con, char *options)
+{
+ int size = options ? strlen(options) : 0;
+
+ if (size >= 3 &&
+ options[size - 3] == 'l' &&
+ options[size - 2] == 'l' &&
+ options[size - 1] >= '1' && options[size - 1] <= '9') {
+ con->loglevel = options[size - 1] - '0';
+
+ /* Catch if the user added a comma after some serial console
+ * options,
+ * i.e. console=ttyS0,9600n8,ll3
+ * the first comma is gone at this point, but we need to delete
+ * the second one.
+ */
+ if (size > 3 && options[size - 4] == ',')
+ options[size - 4] = 0;
+ else
+ options[size - 3] = 0;
+ } else
+ con->loglevel = 0;
+
+ return options;
+}
+
static int __add_preferred_console(char *name, int idx, char *options,
char *brl_options)
{
@@ -1949,12 +1979,15 @@ static int __add_preferred_console(char *name, int idx, char *options,
if (!brl_options)
selected_console = i;
strlcpy(c->name, name, sizeof(c->name));
- c->options = options;
+
+ c->options = setup_per_console_loglevel(c, options);
+
braille_set_options(c, brl_options);
c->index = idx;
return 0;
}
+
/*
* Set up a console. Called via do_early_param() in init/main.c
* for each "console=" parameter in the boot command line.
@@ -2478,6 +2511,8 @@ void register_console(struct console *newcon)
if (newcon->setup &&
newcon->setup(newcon, console_cmdline[i].options) != 0)
break;
+
+ newcon->loglevel = c->loglevel;
newcon->flags |= CON_ENABLED;
newcon->index = c->index;
if (i == selected_console) {
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/