Re: [PATCH v4 2/2] thermal: exynos: Add TMU support for Exynos7 SoC

From: Abhilash Kesavan
Date: Mon Feb 02 2015 - 00:39:20 EST

Next message: Peter Hurley: "Re: [PATCH v2 1/4] tty: serial: Add 8250 earlycon to support noinit option"
Previous message: Dave Chinner: "Re: [PATCH] gfs2: use __vmalloc GFP_NOFS for fs-related allocations."
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi Eduardo,

On Sun, Feb 1, 2015 at 12:54 AM, Eduardo Valentin <edubezval@xxxxxxxxx> wrote:
> On Tue, Jan 27, 2015 at 11:18:22AM +0530, Abhilash Kesavan wrote:
>> Add registers, bit fields and compatible strings for Exynos7 TMU
>> (Thermal Management Unit). Following are a few of the differences
>> in the Exynos7 TMU from earlier SoCs:
>> - 8 trigger levels
>> - Different bit offsets and more registers for the rising
>> and falling thresholds.
>> - New power down detection bit in the TMU_CONTROL register
>> which does not update the CURRENT_TEMP0 when tmu power down
>> is detected.
>> - Change in bit offset for the NEXT_DATA field of EMUL_CON
>> register. EMUL_CON register address has also changed.
>> - INTSTAT and INTCLEAR registers present in earlier SoCs
>> have been combined into one INTPEND register. The register
>> address for INTCLEAR and INTPEND is also different.
>> - Since there are 8 rising/falling interrupts as against
>> at most 4 in earlier SoCs the INTEN bit offsets are different.
>> - Multiple probe support which is handled by a TMU_CONTROL1
>> register (No support for this in the current patch).
>>
>> This patch adds special clock support required only for Exynos7. It
>> also updates the "code_to_temp" prototype as Exynos7 has 9 bit
>> code-temp mapping.
>>
>> Signed-off-by: Abhilash Kesavan <a.kesavan@xxxxxxxxxxx>
>
> Applied to my -fixes branch. However, I had to amend it myself to make
> checkpatch.pl --strict silent. In this version, it still outputs:
> CHECK: Alignment should match open parenthesis
> #209: FILE: drivers/thermal/samsung/exynos_tmu.c:558:
> + if (!data->temp_error1 ||
> + (pdata->min_efuse_value > data->temp_error1) ||
>
> CHECK: multiple assignments should be avoided
> #366: FILE: drivers/thermal/samsung/exynos_tmu.c:882:
> + tmu_intstat = tmu_intclear = EXYNOS7_TMU_REG_INTPEND;
>
> total: 0 errors, 0 warnings, 2 checks, 314 lines checked
>
> next, make sure you run checkpatch.pl --strict before sending patches.

Thanks for applying these patches. As this is adding support for a new
SoC, should it not be part of your -next branch ?
I generally just run checkpatch without the "strict" option. Will
ensure that I run it with "strict" in the future.

Regards,
Abhilash
>
>
>> ---
>> This patch set has been tested on linux next-20150123 with Eduardo's
>> thermal-next branch merged along with the arch-side exynos7 related
>> dts changes applied.
>>
>> Changes since v3:
>> Addressed comments from Lukasz Majewski:
>> - Added more comments in the code setting the thresholds.
>> - Split the documentation out into another patch.
>> Changes since v2:
>> - Rebased on top of Lukasz' latest exynos tmu series (v4).
>> - Added new exynos7 soc_type.
>> Changes since v1:
>> - Rebased on top of Lukasz' latest exynos tmu series (v2).
>> - Added sclk support to patch adding Exynos7 tmu support.
>> Previously, it was a separate patch.
>> - Used the SOC type to decide if sclk is present.
>>
>> drivers/thermal/samsung/exynos_tmu.c | 204 ++++++++++++++++++++++++++++++++--
>> drivers/thermal/samsung/exynos_tmu.h | 1 +
>> 2 files changed, 197 insertions(+), 8 deletions(-)
>>
>> diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c
>> index 852e622..660ff69 100644
>> --- a/drivers/thermal/samsung/exynos_tmu.c
>> +++ b/drivers/thermal/samsung/exynos_tmu.c
>> @@ -119,6 +119,26 @@
>> #define EXYNOS5440_TMU_TH_RISE4_SHIFT 24
>> #define EXYNOS5440_EFUSE_SWAP_OFFSET 8
>>
>> +/* Exynos7 specific registers */
>> +#define EXYNOS7_THD_TEMP_RISE7_6 0x50
>> +#define EXYNOS7_THD_TEMP_FALL7_6 0x60
>> +#define EXYNOS7_TMU_REG_INTEN 0x110
>> +#define EXYNOS7_TMU_REG_INTPEND 0x118
>> +#define EXYNOS7_TMU_REG_EMUL_CON 0x160
>> +
>> +#define EXYNOS7_TMU_TEMP_MASK 0x1ff
>> +#define EXYNOS7_PD_DET_EN_SHIFT 23
>> +#define EXYNOS7_TMU_INTEN_RISE0_SHIFT 0
>> +#define EXYNOS7_TMU_INTEN_RISE1_SHIFT 1
>> +#define EXYNOS7_TMU_INTEN_RISE2_SHIFT 2
>> +#define EXYNOS7_TMU_INTEN_RISE3_SHIFT 3
>> +#define EXYNOS7_TMU_INTEN_RISE4_SHIFT 4
>> +#define EXYNOS7_TMU_INTEN_RISE5_SHIFT 5
>> +#define EXYNOS7_TMU_INTEN_RISE6_SHIFT 6
>> +#define EXYNOS7_TMU_INTEN_RISE7_SHIFT 7
>> +#define EXYNOS7_EMUL_DATA_SHIFT 7
>> +#define EXYNOS7_EMUL_DATA_MASK 0x1ff
>> +
>> #define MCELSIUS 1000
>> /**
>> * struct exynos_tmu_data : A structure to hold the private data of the TMU
>> @@ -133,6 +153,7 @@
>> * @lock: lock to implement synchronization.
>> * @clk: pointer to the clock structure.
>> * @clk_sec: pointer to the clock structure for accessing the base_second.
>> + * @sclk: pointer to the clock structure for accessing the tmu special clk.
>> * @temp_error1: fused value of the first point trim.
>> * @temp_error2: fused value of the second point trim.
>> * @regulator: pointer to the TMU regulator structure.
>> @@ -152,8 +173,8 @@ struct exynos_tmu_data {
>> enum soc_type soc;
>> struct work_struct irq_work;
>> struct mutex lock;
>> - struct clk *clk, *clk_sec;
>> - u8 temp_error1, temp_error2;
>> + struct clk *clk, *clk_sec, *sclk;
>> + u16 temp_error1, temp_error2;
>> struct regulator *regulator;
>> struct thermal_zone_device *tzd;
>>
>> @@ -223,7 +244,7 @@ static int temp_to_code(struct exynos_tmu_data *data, u8 temp)
>> * Calculate a temperature value from a temperature code.
>> * The unit of the temperature is degree Celsius.
>> */
>> -static int code_to_temp(struct exynos_tmu_data *data, u8 temp_code)
>> +static int code_to_temp(struct exynos_tmu_data *data, u16 temp_code)
>> {
>> struct exynos_tmu_platform_data *pdata = data->pdata;
>> int temp;
>> @@ -513,6 +534,84 @@ static int exynos5440_tmu_initialize(struct platform_device *pdev)
>> return ret;
>> }
>>
>> +static int exynos7_tmu_initialize(struct platform_device *pdev)
>> +{
>> + struct exynos_tmu_data *data = platform_get_drvdata(pdev);
>> + struct thermal_zone_device *tz = data->tzd;
>> + struct exynos_tmu_platform_data *pdata = data->pdata;
>> + unsigned int status, trim_info;
>> + unsigned int rising_threshold = 0, falling_threshold = 0;
>> + int ret = 0, threshold_code, i;
>> + unsigned long temp, temp_hist;
>> + unsigned int reg_off, bit_off;
>> +
>> + status = readb(data->base + EXYNOS_TMU_REG_STATUS);
>> + if (!status) {
>> + ret = -EBUSY;
>> + goto out;
>> + }
>> +
>> + trim_info = readl(data->base + EXYNOS_TMU_REG_TRIMINFO);
>> +
>> + data->temp_error1 = trim_info & EXYNOS7_TMU_TEMP_MASK;
>> + if (!data->temp_error1 ||
>> + (pdata->min_efuse_value > data->temp_error1) ||
>> + (data->temp_error1 > pdata->max_efuse_value))
>> + data->temp_error1 = pdata->efuse_value & EXYNOS_TMU_TEMP_MASK;
>> +
>> + /* Write temperature code for rising and falling threshold */
>> + for (i = (of_thermal_get_ntrips(tz) - 1); i >= 0; i--) {
>> + /*
>> + * On exynos7 there are 4 rising and 4 falling threshold
>> + * registers (0x50-0x5c and 0x60-0x6c respectively). Each
>> + * register holds the value of two threshold levels (at bit
>> + * offsets 0 and 16). Based on the fact that there are atmost
>> + * eight possible trigger levels, calculate the register and
>> + * bit offsets where the threshold levels are to be written.
>> + *
>> + * e.g. EXYNOS7_THD_TEMP_RISE7_6 (0x50)
>> + * [24:16] - Threshold level 7
>> + * [8:0] - Threshold level 6
>> + * e.g. EXYNOS7_THD_TEMP_RISE5_4 (0x54)
>> + * [24:16] - Threshold level 5
>> + * [8:0] - Threshold level 4
>> + *
>> + * and similarly for falling thresholds.
>> + *
>> + * Based on the above, calculate the register and bit offsets
>> + * for rising/falling threshold levels and populate them.
>> + */
>> + reg_off = ((7 - i) / 2) * 4;
>> + bit_off = ((8 - i) % 2);
>> +
>> + tz->ops->get_trip_temp(tz, i, &temp);
>> + temp /= MCELSIUS;
>> +
>> + tz->ops->get_trip_hyst(tz, i, &temp_hist);
>> + temp_hist = temp - (temp_hist / MCELSIUS);
>> +
>> + /* Set 9-bit temperature code for rising threshold levels */
>> + threshold_code = temp_to_code(data, temp);
>> + rising_threshold = readl(data->base +
>> + EXYNOS7_THD_TEMP_RISE7_6 + reg_off);
>> + rising_threshold &= ~(EXYNOS7_TMU_TEMP_MASK << (16 * bit_off));
>> + rising_threshold |= threshold_code << (16 * bit_off);
>> + writel(rising_threshold,
>> + data->base + EXYNOS7_THD_TEMP_RISE7_6 + reg_off);
>> +
>> + /* Set 9-bit temperature code for falling threshold levels */
>> + threshold_code = temp_to_code(data, temp_hist);
>> + falling_threshold &= ~(EXYNOS7_TMU_TEMP_MASK << (16 * bit_off));
>> + falling_threshold |= threshold_code << (16 * bit_off);
>> + writel(falling_threshold,
>> + data->base + EXYNOS7_THD_TEMP_FALL7_6 + reg_off);
>> + }
>> +
>> + data->tmu_clear_irqs(data);
>> +out:
>> + return ret;
>> +}
>> +
>> static void exynos4210_tmu_control(struct platform_device *pdev, bool on)
>> {
>> struct exynos_tmu_data *data = platform_get_drvdata(pdev);
>> @@ -573,6 +672,46 @@ static void exynos5440_tmu_control(struct platform_device *pdev, bool on)
>> writel(con, data->base + EXYNOS5440_TMU_S0_7_CTRL);
>> }
>>
>> +static void exynos7_tmu_control(struct platform_device *pdev, bool on)
>> +{
>> + struct exynos_tmu_data *data = platform_get_drvdata(pdev);
>> + struct thermal_zone_device *tz = data->tzd;
>> + unsigned int con, interrupt_en;
>> +
>> + con = get_con_reg(data, readl(data->base + EXYNOS_TMU_REG_CONTROL));
>> +
>> + if (on) {
>> + con |= (1 << EXYNOS_TMU_CORE_EN_SHIFT);
>> + interrupt_en =
>> + (of_thermal_is_trip_valid(tz, 7)
>> + << EXYNOS7_TMU_INTEN_RISE7_SHIFT) |
>> + (of_thermal_is_trip_valid(tz, 6)
>> + << EXYNOS7_TMU_INTEN_RISE6_SHIFT) |
>> + (of_thermal_is_trip_valid(tz, 5)
>> + << EXYNOS7_TMU_INTEN_RISE5_SHIFT) |
>> + (of_thermal_is_trip_valid(tz, 4)
>> + << EXYNOS7_TMU_INTEN_RISE4_SHIFT) |
>> + (of_thermal_is_trip_valid(tz, 3)
>> + << EXYNOS7_TMU_INTEN_RISE3_SHIFT) |
>> + (of_thermal_is_trip_valid(tz, 2)
>> + << EXYNOS7_TMU_INTEN_RISE2_SHIFT) |
>> + (of_thermal_is_trip_valid(tz, 1)
>> + << EXYNOS7_TMU_INTEN_RISE1_SHIFT) |
>> + (of_thermal_is_trip_valid(tz, 0)
>> + << EXYNOS7_TMU_INTEN_RISE0_SHIFT);
>> +
>> + interrupt_en |=
>> + interrupt_en << EXYNOS_TMU_INTEN_FALL0_SHIFT;
>> + } else {
>> + con &= ~(1 << EXYNOS_TMU_CORE_EN_SHIFT);
>> + interrupt_en = 0; /* Disable all interrupts */
>> + }
>> + con |= 1 << EXYNOS7_PD_DET_EN_SHIFT;
>> +
>> + writel(interrupt_en, data->base + EXYNOS7_TMU_REG_INTEN);
>> + writel(con, data->base + EXYNOS_TMU_REG_CONTROL);
>> +}
>> +
>> static int exynos_get_temp(void *p, long *temp)
>> {
>> struct exynos_tmu_data *data = p;
>> @@ -602,9 +741,19 @@ static u32 get_emul_con_reg(struct exynos_tmu_data *data, unsigned int val,
>> val &= ~(EXYNOS_EMUL_TIME_MASK << EXYNOS_EMUL_TIME_SHIFT);
>> val |= (EXYNOS_EMUL_TIME << EXYNOS_EMUL_TIME_SHIFT);
>> }
>> - val &= ~(EXYNOS_EMUL_DATA_MASK << EXYNOS_EMUL_DATA_SHIFT);
>> - val |= (temp_to_code(data, temp) << EXYNOS_EMUL_DATA_SHIFT) |
>> - EXYNOS_EMUL_ENABLE;
>> + if (data->soc == SOC_ARCH_EXYNOS7) {
>> + val &= ~(EXYNOS7_EMUL_DATA_MASK <<
>> + EXYNOS7_EMUL_DATA_SHIFT);
>> + val |= (temp_to_code(data, temp) <<
>> + EXYNOS7_EMUL_DATA_SHIFT) |
>> + EXYNOS_EMUL_ENABLE;
>> + } else {
>> + val &= ~(EXYNOS_EMUL_DATA_MASK <<
>> + EXYNOS_EMUL_DATA_SHIFT);
>> + val |= (temp_to_code(data, temp) <<
>> + EXYNOS_EMUL_DATA_SHIFT) |
>> + EXYNOS_EMUL_ENABLE;
>> + }
>> } else {
>> val &= ~EXYNOS_EMUL_ENABLE;
>> }
>> @@ -620,6 +769,8 @@ static void exynos4412_tmu_set_emulation(struct exynos_tmu_data *data,
>>
>> if (data->soc == SOC_ARCH_EXYNOS5260)
>> emul_con = EXYNOS5260_EMUL_CON;
>> + else if (data->soc == SOC_ARCH_EXYNOS7)
>> + emul_con = EXYNOS7_TMU_REG_EMUL_CON;
>> else
>> emul_con = EXYNOS_EMUL_CON;
>>
>> @@ -683,6 +834,12 @@ static int exynos5440_tmu_read(struct exynos_tmu_data *data)
>> return readb(data->base + EXYNOS5440_TMU_S0_7_TEMP);
>> }
>>
>> +static int exynos7_tmu_read(struct exynos_tmu_data *data)
>> +{
>> + return readw(data->base + EXYNOS_TMU_REG_CURRENT_TEMP) &
>> + EXYNOS7_TMU_TEMP_MASK;
>> +}
>> +
>> static void exynos_tmu_work(struct work_struct *work)
>> {
>> struct exynos_tmu_data *data = container_of(work,
>> @@ -721,6 +878,8 @@ static void exynos4210_tmu_clear_irqs(struct exynos_tmu_data *data)
>> if (data->soc == SOC_ARCH_EXYNOS5260) {
>> tmu_intstat = EXYNOS5260_TMU_REG_INTSTAT;
>> tmu_intclear = EXYNOS5260_TMU_REG_INTCLEAR;
>> + } else if (data->soc == SOC_ARCH_EXYNOS7) {
>> + tmu_intstat = tmu_intclear = EXYNOS7_TMU_REG_INTPEND;
>> } else {
>> tmu_intstat = EXYNOS_TMU_REG_INTSTAT;
>> tmu_intclear = EXYNOS_TMU_REG_INTCLEAR;
>> @@ -782,6 +941,9 @@ static const struct of_device_id exynos_tmu_match[] = {
>> {
>> .compatible = "samsung,exynos5440-tmu",
>> },
>> + {
>> + .compatible = "samsung,exynos7-tmu",
>> + },
>> {},
>> };
>> MODULE_DEVICE_TABLE(of, exynos_tmu_match);
>> @@ -805,6 +967,8 @@ static int exynos_of_get_soc_type(struct device_node *np)
>> return SOC_ARCH_EXYNOS5420_TRIMINFO;
>> else if (of_device_is_compatible(np, "samsung,exynos5440-tmu"))
>> return SOC_ARCH_EXYNOS5440;
>> + else if (of_device_is_compatible(np, "samsung,exynos7-tmu"))
>> + return SOC_ARCH_EXYNOS7;
>>
>> return -EINVAL;
>> }
>> @@ -928,6 +1092,13 @@ static int exynos_map_dt_data(struct platform_device *pdev)
>> data->tmu_set_emulation = exynos5440_tmu_set_emulation;
>> data->tmu_clear_irqs = exynos5440_tmu_clear_irqs;
>> break;
>> + case SOC_ARCH_EXYNOS7:
>> + data->tmu_initialize = exynos7_tmu_initialize;
>> + data->tmu_control = exynos7_tmu_control;
>> + data->tmu_read = exynos7_tmu_read;
>> + data->tmu_set_emulation = exynos4412_tmu_set_emulation;
>> + data->tmu_clear_irqs = exynos4210_tmu_clear_irqs;
>> + break;
>> default:
>> dev_err(&pdev->dev, "Platform not supported\n");
>> return -EINVAL;
>> @@ -1018,21 +1189,37 @@ static int exynos_tmu_probe(struct platform_device *pdev)
>> goto err_clk_sec;
>> }
>>
>> + if (data->soc == SOC_ARCH_EXYNOS7) {
>> + data->sclk = devm_clk_get(&pdev->dev, "tmu_sclk");
>> + if (IS_ERR(data->sclk)) {
>> + dev_err(&pdev->dev, "Failed to get sclk\n");
>> + goto err_clk;
>> + } else {
>> + ret = clk_prepare_enable(data->sclk);
>> + if (ret) {
>> + dev_err(&pdev->dev, "Failed to enable sclk\n");
>> + goto err_clk;
>> + }
>> + }
>> + }
>> +
>> ret = exynos_tmu_initialize(pdev);
>> if (ret) {
>> dev_err(&pdev->dev, "Failed to initialize TMU\n");
>> - goto err_clk;
>> + goto err_sclk;
>> }
>>
>> ret = devm_request_irq(&pdev->dev, data->irq, exynos_tmu_irq,
>> IRQF_TRIGGER_RISING | IRQF_SHARED, dev_name(&pdev->dev), data);
>> if (ret) {
>> dev_err(&pdev->dev, "Failed to request irq: %d\n", data->irq);
>> - goto err_clk;
>> + goto err_sclk;
>> }
>>
>> exynos_tmu_control(pdev, true);
>> return 0;
>> +err_sclk:
>> + clk_disable_unprepare(data->sclk);
>> err_clk:
>> clk_unprepare(data->clk);
>> err_clk_sec:
>> @@ -1052,6 +1239,7 @@ static int exynos_tmu_remove(struct platform_device *pdev)
>> thermal_zone_of_sensor_unregister(&pdev->dev, tzd);
>> exynos_tmu_control(pdev, false);
>>
>> + clk_disable_unprepare(data->sclk);
>> clk_unprepare(data->clk);
>> if (!IS_ERR(data->clk_sec))
>> clk_unprepare(data->clk_sec);
>> diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h
>> index 9f9b1b8..4d71ec6 100644
>> --- a/drivers/thermal/samsung/exynos_tmu.h
>> +++ b/drivers/thermal/samsung/exynos_tmu.h
>> @@ -34,6 +34,7 @@ enum soc_type {
>> SOC_ARCH_EXYNOS5420,
>> SOC_ARCH_EXYNOS5420_TRIMINFO,
>> SOC_ARCH_EXYNOS5440,
>> + SOC_ARCH_EXYNOS7,
>> };
>>
>> /**
>> --
>> 1.7.9.5
>>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Peter Hurley: "Re: [PATCH v2 1/4] tty: serial: Add 8250 earlycon to support noinit option"
Previous message: Dave Chinner: "Re: [PATCH] gfs2: use __vmalloc GFP_NOFS for fs-related allocations."
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]