Re: [3.18.3 BISECTED REGRESSION] scx200_acb / cs5535-smb / geodewdt / cs5535-clockevt torpedoed
From: Nix
Date: Mon Feb 02 2015 - 12:37:28 EST
On 2 Feb 2015, Myron Stowe verbalised:
> Nix:
>
> Thanks for the work you've already done with the bisection. Let's see
> if we can get to the bottom of this. Would you capture two couple sets
> of logs, one without the issue and another set with the commit at issue
> included for comparison.
> For each set please capture:
> a 'dmesg' log with the kernel boot parameters 'debug' and
> 'ignore_loglevel' added (the entire log from booting),
Good boot (commit reverted):
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.18.5+ (compiler@fold) (gcc version 4.8.4 20140605 (prerelease) (GCC) ) #1 Fri Jan 30 21:05:54 GMT 2015
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
[ 0.000000] debug: ignoring loglevel setting.
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x20000 max_arch_pfn = 0x100000
[ 0.000000] initial memory mapped: [mem 0x00000000-0x007fffff]
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x1fc00000-0x1fffffff]
[ 0.000000] [mem 0x1fc00000-0x1fffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x18000000-0x1fbfffff]
[ 0.000000] [mem 0x18000000-0x1fbfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x17ffffff]
[ 0.000000] [mem 0x00100000-0x003fffff] page 4k
[ 0.000000] [mem 0x00400000-0x17ffffff] page 2M
[ 0.000000] 512MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 20000000
[ 0.000000] low ram: 0 - 20000000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x1fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0x1fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00001000-0x1fffffff]
[ 0.000000] On node 0 totalpages: 130974
[ 0.000000] free_area_init_node: node 0, pgdat c0450eac, node_mem_map dfc00020
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] No local APIC present or hardware disabled
[ 0.000000] APIC: disable apic facility
[ 0.000000] APIC: switched to apic NOOP
[ 0.000000] e820: [mem 0x20000000-0xffefffff] available for PCI devices
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129950
[ 0.000000] Kernel command line: BOOT_IMAGE=Linux console=ttyS0,19200 root=/dev/sda1 netconsole=24183@xxxxxxxxxxxx/eth0,24183@xxxxxxxxxxxxx/00:e0:81:c0:91:1b ignore_loglevel debug
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Memory: 515520K/523896K available (2466K kernel code, 239K rwdata, 720K rodata, 208K init, 152K bss, 8376K reserved)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfffa4000 - 0xfffff000 ( 364 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xfffa2000 ( 503 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] .init : 0xc045b000 - 0xc048f000 ( 208 kB)
[ 0.000000] .data : 0xc0368dd5 - 0xc0459cc0 ( 963 kB)
[ 0.000000] .text : 0xc0100000 - 0xc0368dd5 (2467 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:2304 nr_irqs:24 0
[ 0.000000] CPU 0 irqstacks, hard=df408000 soft=df40a000
[ 0.000000] console [ttyS0] enabled
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 499.914 MHz processor
[ 0.030019] Calibrating delay loop (skipped), value calculated using timer frequency.. 999.82 BogoMIPS (lpj=4999140)
[ 0.050011] pid_max: default: 32768 minimum: 101
[ 0.060118] Security Framework initialized
[ 0.070019] Yama: becoming mindful.
[ 0.080082] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090016] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100885] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.100885] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[ 0.110010] CPU: Geode(TM) Integrated Processor by AMD PCS (fam: 05, model: 0a, stepping: 02)
[ 0.150385] Performance Events: no PMU driver, software events only.
[ 0.182326] NET: Registered protocol family 16
[ 0.201605] PCI: PCI BIOS revision 2.01 entry at 0xfac61, last bus=1
[ 0.210011] PCI: Using configuration type 1 for base access
[ 0.231198] SCSI subsystem initialized
[ 0.240206] libata version 3.00 loaded.
[ 0.250167] usbcore: registered new interface driver usbfs
[ 0.260082] usbcore: registered new interface driver hub
[ 0.270074] usbcore: registered new device driver usb
[ 0.280108] PCI: Probing PCI hardware
[ 0.290013] PCI: root bus 00: using default resources
[ 0.300011] PCI: Probing PCI hardware (bus 00)
[ 0.310160] PCI host bridge to bus 0000:00
[ 0.320027] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.330021] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
[ 0.340018] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.350114] pci 0000:00:01.0: [1022:2080] type 00 class 0x060000
[ 0.360972] pci 0000:00:01.2: [1022:2082] type 00 class 0x101000
[ 0.370199] pci 0000:00:01.2: reg 0x10: [mem 0xa0000000-0xa0003fff]
[ 0.381186] pci 0000:00:06.0: [1106:3053] type 00 class 0x020000
[ 0.390038] pci 0000:00:06.0: reg 0x10: [io 0xe100-0xe1ff]
[ 0.400029] pci 0000:00:06.0: reg 0x14: [mem 0xa0004000-0xa00040ff]
[ 0.410089] pci 0000:00:06.0: supports D1 D2
[ 0.420018] pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.430251] pci 0000:00:07.0: [1106:3053] type 00 class 0x020000
[ 0.440038] pci 0000:00:07.0: reg 0x10: [io 0xe200-0xe2ff]
[ 0.450029] pci 0000:00:07.0: reg 0x14: [mem 0xa0004100-0xa00041ff]
[ 0.460088] pci 0000:00:07.0: supports D1 D2
[ 0.470018] pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.480245] pci 0000:00:08.0: [1106:3053] type 00 class 0x020000
[ 0.490038] pci 0000:00:08.0: reg 0x10: [io 0xe300-0xe3ff]
[ 0.500028] pci 0000:00:08.0: reg 0x14: [mem 0xa0004200-0xa00042ff]
[ 0.510088] pci 0000:00:08.0: supports D1 D2
[ 0.520018] pci 0000:00:08.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.530251] pci 0000:00:09.0: [1106:3053] type 00 class 0x020000
[ 0.540038] pci 0000:00:09.0: reg 0x10: [io 0xe400-0xe4ff]
[ 0.550029] pci 0000:00:09.0: reg 0x14: [mem 0xa0004300-0xa00043ff]
[ 0.560088] pci 0000:00:09.0: supports D1 D2
[ 0.570018] pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.580256] pci 0000:00:0e.0: [104c:ac23] type 01 class 0x060400
[ 0.590382] pci 0000:00:14.0: [1022:2090] type 00 class 0x060100
[ 0.600177] pci 0000:00:14.0: reg 0x10: [io 0x6000-0x7fff]
[ 0.610140] pci 0000:00:14.0: reg 0x14: [io 0x6100-0x61ff]
[ 0.620138] pci 0000:00:14.0: reg 0x18: [io 0x6200-0x63ff]
[ 0.630534] pci 0000:00:14.0: CS5536 ISA bridge bug detected (incorrect header); workaround applied
[ 0.640453] pci 0000:00:14.2: [1022:209a] type 00 class 0x010180
[ 0.650688] pci 0000:00:14.2: reg 0x20: [io 0xe000-0xe00f]
[ 0.660318] pci 0000:00:14.2: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.670018] pci 0000:00:14.2: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.680018] pci 0000:00:14.2: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.690018] pci 0000:00:14.2: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.700522] pci 0000:00:15.0: [1022:2094] type 00 class 0x0c0310
[ 0.710237] pci 0000:00:15.0: reg 0x10: [mem 0xa0005000-0xa0005fff]
[ 0.730400] pci 0000:00:15.1: [1022:2095] type 00 class 0x0c0320
[ 0.740238] pci 0000:00:15.1: reg 0x10: [mem 0xa0006000-0xa0006fff]
[ 0.751553] pci 0000:01:00.0: [1106:3053] type 00 class 0x020000
[ 0.760045] pci 0000:01:00.0: reg 0x10: [io 0xd000-0xd0ff]
[ 0.770033] pci 0000:01:00.0: reg 0x14: [mem 0xa4000000-0xa40000ff]
[ 0.780114] pci 0000:01:00.0: supports D1 D2
[ 0.790018] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.800254] pci 0000:01:01.0: [1106:3053] type 00 class 0x020000
[ 0.810043] pci 0000:01:01.0: reg 0x10: [io 0xd100-0xd1ff]
[ 0.820031] pci 0000:01:01.0: reg 0x14: [mem 0xa4000100-0xa40001ff]
[ 0.830113] pci 0000:01:01.0: supports D1 D2
[ 0.840018] pci 0000:01:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.850260] pci 0000:01:02.0: [1106:3053] type 00 class 0x020000
[ 0.860044] pci 0000:01:02.0: reg 0x10: [io 0xd200-0xd2ff]
[ 0.870032] pci 0000:01:02.0: reg 0x14: [mem 0xa4000200-0xa40002ff]
[ 0.880114] pci 0000:01:02.0: supports D1 D2
[ 0.890019] pci 0000:01:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.900258] pci 0000:01:03.0: [1106:3053] type 00 class 0x020000
[ 0.910044] pci 0000:01:03.0: reg 0x10: [io 0xd300-0xd3ff]
[ 0.920031] pci 0000:01:03.0: reg 0x14: [mem 0xa4000300-0xa40003ff]
[ 0.930114] pci 0000:01:03.0: supports D1 D2
[ 0.940018] pci 0000:01:03.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.950288] pci 0000:00:0e.0: PCI bridge to [bus 01]
[ 0.960026] pci 0000:00:0e.0: bridge window [io 0xd000-0xdfff]
[ 0.970022] pci 0000:00:0e.0: bridge window [mem 0xa4000000-0xa7ffffff]
[ 0.980035] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.990607] PCI: pci_cache_line_size set to 32 bytes
[ 1.000286] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[ 1.011093] Switched to clocksource pit
[ 1.014334] pci 0000:00:0e.0: PCI bridge to [bus 01]
[ 1.024129] pci 0000:00:0e.0: bridge window [io 0xd000-0xdfff]
[ 1.030671] pci 0000:00:0e.0: bridge window [mem 0xa4000000-0xa7ffffff]
[ 1.041384] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 1.054807] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff]
[ 1.062341] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
[ 1.075721] pci_bus 0000:01: resource 1 [mem 0xa4000000-0xa7ffffff]
[ 1.083381] NET: Registered protocol family 2
[ 1.100688] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 1.113008] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 1.121666] TCP: Hash tables configured (established 4096 bind 4096)
[ 1.139809] TCP: reno registered
[ 1.149160] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.154107] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 1.161902] NET: Registered protocol family 1
[ 1.178493] RPC: Registered named UNIX socket transport module.
[ 1.183970] RPC: Registered udp transport module.
[ 1.192142] RPC: Registered tcp transport module.
[ 1.200321] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.219528] PCI: CLS 32 bytes, default 32
[ 1.224011] platform rtc_cmos: registered platform RTC device (no PNP device found)
[ 1.240819] net5501: system is recognized as "net5501"
[ 1.251803] NatSemi SCx200 Driver
[ 1.262561] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 1.299641] VFS: Disk quotas dquot_6.5.2
[ 1.303519] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.314071] msgmni has been set to 1006
[ 1.328283] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.332644] io scheduler noop registered
[ 1.346183] io scheduler deadline registered (default)
[ 1.357428] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 1.376345] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 1.383368] AMD Geode RNG detected
[ 1.393899] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds).
[ 1.411881] loop: module loaded
[ 1.421383] zram: Created 1 device(s) ...
[ 1.435870] cs5535-gpio cs5535-gpio: reserved resource region [io 0x6100-0x61ff]
[ 1.440961] cs5535-mfgpt cs5535-mfgpt: reserved resource region [io 0x6200-0x63ff]
[ 1.456859] cs5535-mfgpt cs5535-mfgpt: 8 MFGPT timers available
[ 1.462537] cs5535-mfd 0000:00:14.0: 5 devices registered.
[ 1.477430] scsi host0: pata_cs5536
[ 1.488855] scsi host1: pata_cs5536
[ 1.500056] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xe000 irq 14
[ 1.501778] ata2: DUMMY
[ 1.517956] via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker
[ 1.534216] via-rhine 0000:00:06.0 eth0: VIA Rhine III (Management Adapter) at 0xe0806000, 00:00:24:cb:c6:a0, IRQ 11
[ 1.548024] via-rhine 0000:00:06.0 eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link cde1
[ 1.563505] via-rhine 0000:00:07.0 eth1: VIA Rhine III (Management Adapter) at 0xe0808100, 00:00:24:cb:c6:a1, IRQ 5
[ 1.576792] via-rhine 0000:00:07.0 eth1: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1
[ 1.592231] via-rhine 0000:00:08.0 eth2: VIA Rhine III (Management Adapter) at 0xe080a200, 00:00:24:cb:c6:a2, IRQ 9
[ 1.605540] via-rhine 0000:00:08.0 eth2: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1
[ 1.621014] via-rhine 0000:00:09.0 eth3: VIA Rhine III (Management Adapter) at 0xe080c300, 00:00:24:cb:c6:a3, IRQ 12
[ 1.634840] via-rhine 0000:00:09.0 eth3: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1
[ 1.650360] via-rhine 0000:01:00.0 eth4: VIA Rhine III (Management Adapter) at 0xe080e000, 00:00:24:d1:2a:3c, IRQ 10
[ 1.664203] via-rhine 0000:01:00.0 eth4: MII PHY found at address 1, status 0x786d advertising 05e1 Link 4de1
[ 1.679675] via-rhine 0000:01:01.0 eth5: VIA Rhine III (Management Adapter) at 0xe0810100, 00:00:24:d1:2a:3d, IRQ 7
[ 1.682988] via-rhine 0000:01:01.0 eth5: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000
[ 1.698466] via-rhine 0000:01:02.0 eth6: VIA Rhine III (Management Adapter) at 0xe0812200, 00:00:24:d1:2a:3e, IRQ 10
[ 1.702288] via-rhine 0000:01:02.0 eth6: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000
[ 1.717765] via-rhine 0000:01:03.0 eth7: VIA Rhine III (Management Adapter) at 0xe0814300, 00:00:24:d1:2a:3f, IRQ 7
[ 1.721069] via-rhine 0000:01:03.0 eth7: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000
[ 1.730619] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.749727] ehci-pci: EHCI PCI platform driver
[ 1.756661] ehci-pci 0000:00:15.1: EHCI Host Controller
[ 1.768030] ehci-pci 0000:00:15.1: new USB bus registered, assigned bus number 1
[ 1.772595] ehci-pci 0000:00:15.1: irq 15, io mem 0xa0006000
[ 1.787133] ata1.00: CFA: SanDisk SDCFH2-002G, HDX 4.32, max MWDMA2
[ 1.794720] ata1.00: 4001760 sectors, multi 0: LBA
[ 1.804227] ehci-pci 0000:00:15.1: USB 2.0 started, EHCI 1.00
[ 1.819140] ata1.00: configured for MWDMA2
[ 1.824097] scsi 0:0:0:0: Direct-Access ATA SanDisk SDCFH2-0 4.32 PQ: 0 ANSI: 5
[ 1.833591] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.845889] sd 0:0:0:0: [sda] 4001760 512-byte logical blocks: (2.04 GB/1.90 GiB)
[ 1.851583] hub 1-0:1.0: USB hub found
[ 1.864318] sd 0:0:0:0: [sda] Write Protect is off
[ 1.873059] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.883423] hub 1-0:1.0: 4 ports detected
[ 1.897560] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1.903918] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.911026] ohci-pci: OHCI PCI platform driver
[ 1.927944] ohci-pci 0000:00:15.0: OHCI PCI host controller
[ 1.931400] ohci-pci 0000:00:15.0: new USB bus registered, assigned bus number 2
[ 1.945769] ohci-pci 0000:00:15.0: irq 15, io mem 0xa0005000
[ 1.959683] sda: sda1
[ 1.964907] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 2.043064] hub 2-0:1.0: USB hub found
[ 2.055607] hub 2-0:1.0: 4 ports detected
[ 2.070339] usbcore: registered new interface driver cdc_acm
[ 2.084266] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.092380] usbcore: registered new interface driver usb-storage
[ 2.108400] i2c /dev entries driver
[ 2.119724] cs5535-smb cs5535-smb: SCx200 device 'CS5535 ACB0' registered
[ 2.120485] pc87360: Device 0x09 not activated
[ 2.138720] cs5535-mfgpt cs5535-mfgpt: registered timer 0
[ 2.141841] Geode LX AES 0000:00:01.2: GEODE AES engine enabled.
[ 2.157966] cs5535-mfgpt cs5535-mfgpt: registered timer 1
[ 2.160372] cs5535-clockevt: Registering MFGPT timer as a clock event, using IRQ 7
[ 2.176094] GACT probability NOT on
[ 2.181159] u32 classifier
[ 2.197488] Performance counters on
[ 2.200584] Actions configured
[ 2.211199] Netfilter messages via NETLINK v0.30.
[ 2.229532] nfnl_acct: registering with nfnetlink.
[ 2.238364] nf_conntrack version 0.5.0 (8055 buckets, 32220 max)
[ 2.245122] ctnetlink v0.93: registering with nfnetlink.
[ 2.258185] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.270334] TCP: cubic registered
[ 2.271743] NET: Registered protocol family 10
[ 2.289400] Switched to clocksource tsc
[ 2.314623] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 2.347315] sit: IPv6 over IPv4 tunneling driver
[ 2.375941] NET: Registered protocol family 17
[ 2.402863] Using IPI Shortcut mode
[ 2.425557] netpoll: netconsole: local port 24183
[ 2.453748] netpoll: netconsole: local IPv4 address 192.168.14.1
[ 2.489711] netpoll: netconsole: interface 'eth0'
[ 2.517887] netpoll: netconsole: remote port 24183
[ 2.546597] netpoll: netconsole: remote IPv4 address 192.168.14.15
[ 2.583602] netpoll: netconsole: remote ethernet address 00:e0:81:c0:91:1b
[ 2.624782] netpoll: netconsole: device eth0 not up yet, forcing it
[ 2.663368] netpoll: netconsole: carrier detect appears untrustworthy, waiting 4 seconds
[ 3.010087] usb 2-1: new full-speed USB device number 2 using ohci-pci
[ 3.288265] cdc_acm 2-1:1.0: This device cannot do calls on its own. It is not a modem.
[ 3.336599] cdc_acm 2-1:1.0: ttyACM0: USB ACM device
[ 6.723598] console [netcon0] enabled
[ 6.745663] netconsole: network logging started
[ 6.777256] VFS: Mounted root (ext2 filesystem) readonly on device 8:1.
[ 6.817329] Freeing unused kernel memory: 208K (c045b000 - c048f000)
[ 6.855847] Write protecting the kernel text: 2468k
[ 6.885171] Write protecting the kernel read-only data: 724k
Bad boot (pristine 3.18.5):
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.18.5+ (compiler@fold) (gcc version 4.8.4 20140605 (prerelease) (GCC) ) #1 Fri Jan 30 20:08:48 GMT 2015
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
[ 0.000000] debug: ignoring loglevel setting.
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x20000 max_arch_pfn = 0x100000
[ 0.000000] initial memory mapped: [mem 0x00000000-0x007fffff]
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x1fc00000-0x1fffffff]
[ 0.000000] [mem 0x1fc00000-0x1fffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x18000000-0x1fbfffff]
[ 0.000000] [mem 0x18000000-0x1fbfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x17ffffff]
[ 0.000000] [mem 0x00100000-0x003fffff] page 4k
[ 0.000000] [mem 0x00400000-0x17ffffff] page 2M
[ 0.000000] 512MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 20000000
[ 0.000000] low ram: 0 - 20000000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x1fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0x1fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00001000-0x1fffffff]
[ 0.000000] On node 0 totalpages: 130974
[ 0.000000] free_area_init_node: node 0, pgdat c0450eac, node_mem_map dfc00020
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] No local APIC present or hardware disabled
[ 0.000000] APIC: disable apic facility
[ 0.000000] APIC: switched to apic NOOP
[ 0.000000] e820: [mem 0x20000000-0xffefffff] available for PCI devices
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129950
[ 0.000000] Kernel command line: BOOT_IMAGE=oldLinux console=ttyS0,19200 root=/dev/sda1 netconsole=24183@xxxxxxxxxxxx/eth0,24183@xxxxxxxxxxxxx/00:e0:81:c0:91:1b ignore_loglevel debug
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Memory: 515520K/523896K available (2466K kernel code, 239K rwdata, 720K rodata, 208K init, 152K bss, 8376K reserved)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfffa4000 - 0xfffff000 ( 364 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xfffa2000 ( 503 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] .init : 0xc045b000 - 0xc048f000 ( 208 kB)
[ 0.000000] .data : 0xc0368e15 - 0xc0459cc0 ( 963 kB)
[ 0.000000] .text : 0xc0100000 - 0xc0368e15 (2467 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:2304 nr_irqs:24 0
[ 0.000000] CPU 0 irqstacks, hard=df408000 soft=df40a000
[ 0.000000] console [ttyS0] enabled
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 499.913 MHz processor
[ 0.030020] Calibrating delay loop (skipped), value calculated using timer frequency.. 999.82 BogoMIPS (lpj=4999130)
[ 0.050011] pid_max: default: 32768 minimum: 101
[ 0.060118] Security Framework initialized
[ 0.070019] Yama: becoming mindful.
[ 0.080082] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090016] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100884] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.100884] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[ 0.110010] CPU: Geode(TM) Integrated Processor by AMD PCS (fam: 05, model: 0a, stepping: 02)
[ 0.150387] Performance Events: no PMU driver, software events only.
[ 0.182329] NET: Registered protocol family 16
[ 0.201611] PCI: PCI BIOS revision 2.01 entry at 0xfac61, last bus=1
[ 0.210011] PCI: Using configuration type 1 for base access
[ 0.231202] SCSI subsystem initialized
[ 0.240205] libata version 3.00 loaded.
[ 0.250169] usbcore: registered new interface driver usbfs
[ 0.260082] usbcore: registered new interface driver hub
[ 0.270074] usbcore: registered new device driver usb
[ 0.280106] PCI: Probing PCI hardware
[ 0.290012] PCI: root bus 00: using default resources
[ 0.300011] PCI: Probing PCI hardware (bus 00)
[ 0.310159] PCI host bridge to bus 0000:00
[ 0.320027] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.330021] pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
[ 0.340018] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.350113] pci 0000:00:01.0: [1022:2080] type 00 class 0x060000
[ 0.360975] pci 0000:00:01.2: [1022:2082] type 00 class 0x101000
[ 0.370200] pci 0000:00:01.2: reg 0x10: [mem 0xa0000000-0xa0003fff]
[ 0.381186] pci 0000:00:06.0: [1106:3053] type 00 class 0x020000
[ 0.390038] pci 0000:00:06.0: reg 0x10: [io 0xe100-0xe1ff]
[ 0.400029] pci 0000:00:06.0: reg 0x14: [mem 0xa0004000-0xa00040ff]
[ 0.410089] pci 0000:00:06.0: supports D1 D2
[ 0.420019] pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.430251] pci 0000:00:07.0: [1106:3053] type 00 class 0x020000
[ 0.440038] pci 0000:00:07.0: reg 0x10: [io 0xe200-0xe2ff]
[ 0.450029] pci 0000:00:07.0: reg 0x14: [mem 0xa0004100-0xa00041ff]
[ 0.460088] pci 0000:00:07.0: supports D1 D2
[ 0.470018] pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.480245] pci 0000:00:08.0: [1106:3053] type 00 class 0x020000
[ 0.490038] pci 0000:00:08.0: reg 0x10: [io 0xe300-0xe3ff]
[ 0.500029] pci 0000:00:08.0: reg 0x14: [mem 0xa0004200-0xa00042ff]
[ 0.510088] pci 0000:00:08.0: supports D1 D2
[ 0.520018] pci 0000:00:08.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.530251] pci 0000:00:09.0: [1106:3053] type 00 class 0x020000
[ 0.540038] pci 0000:00:09.0: reg 0x10: [io 0xe400-0xe4ff]
[ 0.550029] pci 0000:00:09.0: reg 0x14: [mem 0xa0004300-0xa00043ff]
[ 0.560089] pci 0000:00:09.0: supports D1 D2
[ 0.570018] pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.580256] pci 0000:00:0e.0: [104c:ac23] type 01 class 0x060400
[ 0.590382] pci 0000:00:14.0: [1022:2090] type 00 class 0x060100
[ 0.600930] pci 0000:00:14.0: CS5536 ISA bridge bug detected (incorrect header); workaround applied
[ 0.610448] pci 0000:00:14.2: [1022:209a] type 00 class 0x010180
[ 0.620688] pci 0000:00:14.2: reg 0x20: [io 0xe000-0xe00f]
[ 0.630319] pci 0000:00:14.2: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
[ 0.640023] pci 0000:00:14.2: legacy IDE quirk: reg 0x14: [io 0x03f6]
[ 0.650019] pci 0000:00:14.2: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
[ 0.660018] pci 0000:00:14.2: legacy IDE quirk: reg 0x1c: [io 0x0376]
[ 0.670521] pci 0000:00:15.0: [1022:2094] type 00 class 0x0c0310
[ 0.680237] pci 0000:00:15.0: reg 0x10: [mem 0xa0005000-0xa0005fff]
[ 0.700322] pci 0000:00:15.1: [1022:2095] type 00 class 0x0c0320
[ 0.710238] pci 0000:00:15.1: reg 0x10: [mem 0xa0006000-0xa0006fff]
[ 0.721548] pci 0000:01:00.0: [1106:3053] type 00 class 0x020000
[ 0.730045] pci 0000:01:00.0: reg 0x10: [io 0xd000-0xd0ff]
[ 0.740032] pci 0000:01:00.0: reg 0x14: [mem 0xa4000000-0xa40000ff]
[ 0.750114] pci 0000:01:00.0: supports D1 D2
[ 0.760018] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.770256] pci 0000:01:01.0: [1106:3053] type 00 class 0x020000
[ 0.780043] pci 0000:01:01.0: reg 0x10: [io 0xd100-0xd1ff]
[ 0.790032] pci 0000:01:01.0: reg 0x14: [mem 0xa4000100-0xa40001ff]
[ 0.800115] pci 0000:01:01.0: supports D1 D2
[ 0.810018] pci 0000:01:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.820261] pci 0000:01:02.0: [1106:3053] type 00 class 0x020000
[ 0.830044] pci 0000:01:02.0: reg 0x10: [io 0xd200-0xd2ff]
[ 0.840033] pci 0000:01:02.0: reg 0x14: [mem 0xa4000200-0xa40002ff]
[ 0.850115] pci 0000:01:02.0: supports D1 D2
[ 0.860018] pci 0000:01:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.870259] pci 0000:01:03.0: [1106:3053] type 00 class 0x020000
[ 0.880043] pci 0000:01:03.0: reg 0x10: [io 0xd300-0xd3ff]
[ 0.890032] pci 0000:01:03.0: reg 0x14: [mem 0xa4000300-0xa40003ff]
[ 0.900114] pci 0000:01:03.0: supports D1 D2
[ 0.910018] pci 0000:01:03.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.920287] pci 0000:00:0e.0: PCI bridge to [bus 01]
[ 0.930025] pci 0000:00:0e.0: bridge window [io 0xd000-0xdfff]
[ 0.940022] pci 0000:00:0e.0: bridge window [mem 0xa4000000-0xa7ffffff]
[ 0.950034] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[ 0.960607] PCI: pci_cache_line_size set to 32 bytes
[ 0.970284] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[ 0.981088] Switched to clocksource pit
[ 0.984339] pci 0000:00:0e.0: PCI bridge to [bus 01]
[ 0.994133] pci 0000:00:0e.0: bridge window [io 0xd000-0xdfff]
[ 1.000679] pci 0000:00:0e.0: bridge window [mem 0xa4000000-0xa7ffffff]
[ 1.011390] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 1.024811] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff]
[ 1.032347] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff]
[ 1.045727] pci_bus 0000:01: resource 1 [mem 0xa4000000-0xa7ffffff]
[ 1.053388] NET: Registered protocol family 2
[ 1.070694] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 1.083015] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 1.091671] TCP: Hash tables configured (established 4096 bind 4096)
[ 1.109815] TCP: reno registered
[ 1.119164] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.124112] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 1.131906] NET: Registered protocol family 1
[ 1.148499] RPC: Registered named UNIX socket transport module.
[ 1.153978] RPC: Registered udp transport module.
[ 1.162147] RPC: Registered tcp transport module.
[ 1.170327] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.189532] PCI: CLS 32 bytes, default 32
[ 1.194010] platform rtc_cmos: registered platform RTC device (no PNP device found)
[ 1.210824] net5501: system is recognized as "net5501"
[ 1.221812] NatSemi SCx200 Driver
[ 1.232572] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 1.269657] VFS: Disk quotas dquot_6.5.2
[ 1.273530] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.284075] msgmni has been set to 1006
[ 1.298292] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.302649] io scheduler noop registered
[ 1.316186] io scheduler deadline registered (default)
[ 1.327431] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 1.346354] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 1.353378] AMD Geode RNG detected
[ 1.363911] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds).
[ 1.381887] loop: module loaded
[ 1.391395] zram: Created 1 device(s) ...
[ 1.405877] cs5535-gpio cs5535-gpio: can't request region
[ 1.418278] cs5535-gpio: probe of cs5535-gpio failed with error -5
[ 1.425449] cs5535-mfgpt cs5535-mfgpt: can't request region
[ 1.438873] cs5535-mfgpt: probe of cs5535-mfgpt failed with error -5
[ 1.447163] cs5535-mfd 0000:00:14.0: 5 devices registered.
[ 1.462097] scsi host0: pata_cs5536
[ 1.473525] scsi host1: pata_cs5536
[ 1.484730] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xe000 irq 14
[ 1.496451] ata2: DUMMY
[ 1.502618] via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker
[ 1.518801] via-rhine 0000:00:06.0 eth0: VIA Rhine III (Management Adapter) at 0xe0806000, 00:00:24:cb:c6:a0, IRQ 11
[ 1.522645] via-rhine 0000:00:06.0 eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link cde1
[ 1.538087] via-rhine 0000:00:07.0 eth1: VIA Rhine III (Management Adapter) at 0xe0808100, 00:00:24:cb:c6:a1, IRQ 5
[ 1.541360] via-rhine 0000:00:07.0 eth1: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1
[ 1.556758] via-rhine 0000:00:08.0 eth2: VIA Rhine III (Management Adapter) at 0xe080a200, 00:00:24:cb:c6:a2, IRQ 9
[ 1.570049] via-rhine 0000:00:08.0 eth2: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1
[ 1.585530] via-rhine 0000:00:09.0 eth3: VIA Rhine III (Management Adapter) at 0xe080c300, 00:00:24:cb:c6:a3, IRQ 12
[ 1.599327] via-rhine 0000:00:09.0 eth3: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1
[ 1.614825] via-rhine 0000:01:00.0 eth4: VIA Rhine III (Management Adapter) at 0xe080e000, 00:00:24:d1:2a:3c, IRQ 10
[ 1.628670] via-rhine 0000:01:00.0 eth4: MII PHY found at address 1, status 0x786d advertising 05e1 Link 4de1
[ 1.644169] via-rhine 0000:01:01.0 eth5: VIA Rhine III (Management Adapter) at 0xe0810100, 00:00:24:d1:2a:3d, IRQ 7
[ 1.657503] via-rhine 0000:01:01.0 eth5: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000
[ 1.673021] via-rhine 0000:01:02.0 eth6: VIA Rhine III (Management Adapter) at 0xe0812200, 00:00:24:d1:2a:3e, IRQ 10
[ 1.686856] via-rhine 0000:01:02.0 eth6: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000
[ 1.702378] via-rhine 0000:01:03.0 eth7: VIA Rhine III (Management Adapter) at 0xe0814300, 00:00:24:d1:2a:3f, IRQ 7
[ 1.715689] via-rhine 0000:01:03.0 eth7: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000
[ 1.725238] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.734346] ehci-pci: EHCI PCI platform driver
[ 1.741279] ehci-pci 0000:00:15.1: EHCI Host Controller
[ 1.752652] ehci-pci 0000:00:15.1: new USB bus registered, assigned bus number 1
[ 1.767210] ehci-pci 0000:00:15.1: irq 15, io mem 0xa0006000
[ 1.771753] ata1.00: CFA: SanDisk SDCFH2-002G, HDX 4.32, max MWDMA2
[ 1.789340] ata1.00: 4001760 sectors, multi 0: LBA
[ 1.798849] ehci-pci 0000:00:15.1: USB 2.0 started, EHCI 1.00
[ 1.803766] ata1.00: configured for MWDMA2
[ 1.818724] scsi 0:0:0:0: Direct-Access ATA SanDisk SDCFH2-0 4.32 PQ: 0 ANSI: 5
[ 1.828065] hub 1-0:1.0: USB hub found
[ 1.830601] hub 1-0:1.0: 4 ports detected
[ 1.845607] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.857873] sd 0:0:0:0: [sda] 4001760 512-byte logical blocks: (2.04 GB/1.90 GiB)
[ 1.862962] sd 0:0:0:0: [sda] Write Protect is off
[ 1.871698] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.882657] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.899700] ohci-pci: OHCI PCI platform driver
[ 1.906618] ohci-pci 0000:00:15.0: OHCI PCI host controller
[ 1.920026] ohci-pci 0000:00:15.0: new USB bus registered, assigned bus number 2
[ 1.924410] ohci-pci 0000:00:15.0: irq 15, io mem 0xa0005000
[ 1.938433] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1.944913] sda: sda1
[ 1.960113] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 2.023154] hub 2-0:1.0: USB hub found
[ 2.035653] hub 2-0:1.0: 4 ports detected
[ 2.050393] usbcore: registered new interface driver cdc_acm
[ 2.064313] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.072426] usbcore: registered new interface driver usb-storage
[ 2.088447] i2c /dev entries driver
[ 2.099501] scx200_acb: can't allocate io 0x0-0x7
[ 2.107733] cs5535-smb: probe of cs5535-smb failed with error -5
[ 2.113818] pc87360: Device 0x09 not activated
[ 2.122063] geodewdt: No timers were available
[ 2.139437] Geode LX AES 0000:00:01.2: GEODE AES engine enabled.
[ 2.145579] cs5535-clockevt: Could not allocate MFGPT timer
[ 2.159086] GACT probability NOT on
[ 2.170991] u32 classifier
[ 2.187209] Performance counters on
[ 2.200184] Actions configured
[ 2.200700] Netfilter messages via NETLINK v0.30.
[ 2.218929] nfnl_acct: registering with nfnetlink.
[ 2.227675] nf_conntrack version 0.5.0 (8055 buckets, 32220 max)
[ 2.234361] ctnetlink v0.93: registering with nfnetlink.
[ 2.247327] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.259351] TCP: cubic registered
[ 2.270695] NET: Registered protocol family 10
[ 2.288282] Switched to clocksource tsc
[ 2.313217] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 2.345915] sit: IPv6 over IPv4 tunneling driver
[ 2.374551] NET: Registered protocol family 17
[ 2.401476] Using IPI Shortcut mode
[ 2.424131] netpoll: netconsole: local port 24183
[ 2.452356] netpoll: netconsole: local IPv4 address 192.168.14.1
[ 2.488319] netpoll: netconsole: interface 'eth0'
[ 2.516496] netpoll: netconsole: remote port 24183
[ 2.545205] netpoll: netconsole: remote IPv4 address 192.168.14.15
[ 2.582213] netpoll: netconsole: remote ethernet address 00:e0:81:c0:91:1b
[ 2.623390] netpoll: netconsole: device eth0 not up yet, forcing it
[ 2.661947] netpoll: netconsole: carrier detect appears untrustworthy, waiting 4 seconds
[ 3.010077] usb 2-1: new full-speed USB device number 2 using ohci-pci
[ 3.281268] cdc_acm 2-1:1.0: This device cannot do calls on its own. It is not a modem.
[ 3.329568] cdc_acm 2-1:1.0: ttyACM0: USB ACM device
[ 6.723581] console [netcon0] enabled
[ 6.745559] netconsole: network logging started
[ 6.776857] VFS: Mounted root (ext2 filesystem) readonly on device 8:1.
[ 6.816870] Freeing unused kernel memory: 208K (c045b000 - c048f000)
[ 6.855270] Write protecting the kernel text: 2468k
[ 6.884621] Write protecting the kernel read-only data: 724k
Diff so you don't have to (and to ensure I didn't miss a line out in the
copy-and-paste from the minicom scrollback):
--- /tmp/good-boot 2015-02-02 17:30:23.527493289 +0000
+++ /tmp/bad-boot 2015-02-02 17:30:38.506270774 +0000
@@ -1,5 +1,5 @@
Initializing cgroup subsys cpu
-Linux version 3.18.5+ (compiler@fold) (gcc version 4.8.4 20140605 (prerelease) (GCC) ) #1 Fri Jan 30 21:05:54 GMT 2015
+Linux version 3.18.5+ (compiler@fold) (gcc version 4.8.4 20140605 (prerelease) (GCC) ) #1 Fri Jan 30 20:08:48 GMT 2015
e820: BIOS-provided physical RAM map:
BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
@@ -48,7 +48,7 @@
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129950
-Kernel command line: BOOT_IMAGE=Linux console=ttyS0,19200 root=/dev/sda1 netconsole=24183@xxxxxxxxxxxx/eth0,24183@xxxxxxxxxxxxx/00:e0:81:c0:91:1b ignore_loglevel debug
+Kernel command line: BOOT_IMAGE=oldLinux console=ttyS0,19200 root=/dev/sda1 netconsole=24183@xxxxxxxxxxxx/eth0,24183@xxxxxxxxxxxxx/00:e0:81:c0:91:1b ignore_loglevel debug
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
@@ -59,16 +59,16 @@
vmalloc : 0xe0800000 - 0xfffa2000 ( 503 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
.init : 0xc045b000 - 0xc048f000 ( 208 kB)
- .data : 0xc0368dd5 - 0xc0459cc0 ( 963 kB)
- .text : 0xc0100000 - 0xc0368dd5 (2467 kB)
+ .data : 0xc0368e15 - 0xc0459cc0 ( 963 kB)
+ .text : 0xc0100000 - 0xc0368e15 (2467 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:2304 nr_irqs:24 0
CPU 0 irqstacks, hard=df408000 soft=df40a000
console [ttyS0] enabled
tsc: Fast TSC calibration using PIT
-tsc: Detected 499.914 MHz processor
-Calibrating delay loop (skipped), value calculated using timer frequency.. 999.82 BogoMIPS (lpj=4999140)
+tsc: Detected 499.913 MHz processor
+Calibrating delay loop (skipped), value calculated using timer frequency.. 999.82 BogoMIPS (lpj=4999130)
pid_max: default: 32768 minimum: 101
Security Framework initialized
Yama: becoming mindful.
@@ -118,9 +118,6 @@
pci 0000:00:09.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0e.0: [104c:ac23] type 01 class 0x060400
pci 0000:00:14.0: [1022:2090] type 00 class 0x060100
-pci 0000:00:14.0: reg 0x10: [io 0x6000-0x7fff]
-pci 0000:00:14.0: reg 0x14: [io 0x6100-0x61ff]
-pci 0000:00:14.0: reg 0x18: [io 0x6200-0x63ff]
pci 0000:00:14.0: CS5536 ISA bridge bug detected (incorrect header); workaround applied
pci 0000:00:14.2: [1022:209a] type 00 class 0x010180
pci 0000:00:14.2: reg 0x20: [io 0xe000-0xe00f]
@@ -195,9 +192,10 @@
Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds).
loop: module loaded
zram: Created 1 device(s) ...
-cs5535-gpio cs5535-gpio: reserved resource region [io 0x6100-0x61ff]
-cs5535-mfgpt cs5535-mfgpt: reserved resource region [io 0x6200-0x63ff]
-cs5535-mfgpt cs5535-mfgpt: 8 MFGPT timers available
+cs5535-gpio cs5535-gpio: can't request region
+cs5535-gpio: probe of cs5535-gpio failed with error -5
+cs5535-mfgpt cs5535-mfgpt: can't request region
+cs5535-mfgpt: probe of cs5535-mfgpt failed with error -5
cs5535-mfd 0000:00:14.0: 5 devices registered.
scsi host0: pata_cs5536
scsi host1: pata_cs5536
@@ -230,18 +228,18 @@
ehci-pci 0000:00:15.1: USB 2.0 started, EHCI 1.00
ata1.00: configured for MWDMA2
scsi 0:0:0:0: Direct-Access ATA SanDisk SDCFH2-0 4.32 PQ: 0 ANSI: 5
+hub 1-0:1.0: USB hub found
+hub 1-0:1.0: 4 ports detected
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 4001760 512-byte logical blocks: (2.04 GB/1.90 GiB)
-hub 1-0:1.0: USB hub found
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
-hub 1-0:1.0: 4 ports detected
-sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
ohci-pci 0000:00:15.0: OHCI PCI host controller
ohci-pci 0000:00:15.0: new USB bus registered, assigned bus number 2
ohci-pci 0000:00:15.0: irq 15, io mem 0xa0005000
+sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
hub 2-0:1.0: USB hub found
@@ -250,12 +248,12 @@
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usb-storage
i2c /dev entries driver
-cs5535-smb cs5535-smb: SCx200 device 'CS5535 ACB0' registered
+scx200_acb: can't allocate io 0x0-0x7
+cs5535-smb: probe of cs5535-smb failed with error -5
pc87360: Device 0x09 not activated
-cs5535-mfgpt cs5535-mfgpt: registered timer 0
+geodewdt: No timers were available
Geode LX AES 0000:00:01.2: GEODE AES engine enabled.
-cs5535-mfgpt cs5535-mfgpt: registered timer 1
-cs5535-clockevt: Registering MFGPT timer as a clock event, using IRQ 7
+cs5535-clockevt: Could not allocate MFGPT timer
GACT probability NOT on
u32 classifier
Performance counters on
The hunk at line 118 looks like a smoking gun to me.
> a capture of 'lspci -t',
Good boot (commit reverted), done a -tv because it's just more helpful:
-[0000:00]-+-01.0 Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] Host Bridge
+-01.2 Advanced Micro Devices, Inc. [AMD] Geode LX AES Security Block
+-06.0 VIA Technologies, Inc. VT6105M [Rhine-III]
+-07.0 VIA Technologies, Inc. VT6105M [Rhine-III]
+-08.0 VIA Technologies, Inc. VT6105M [Rhine-III]
+-09.0 VIA Technologies, Inc. VT6105M [Rhine-III]
+-0e.0-[01]--+-00.0 VIA Technologies, Inc. VT6105M [Rhine-III]
| +-01.0 VIA Technologies, Inc. VT6105M [Rhine-III]
| +-02.0 VIA Technologies, Inc. VT6105M [Rhine-III]
| \-03.0 VIA Technologies, Inc. VT6105M [Rhine-III]
+-14.0 Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] ISA
+-14.2 Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] IDE
+-15.0 Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] OHC
\-15.1 Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] EHC
Bad boot (pristine 3.18.5):
-[0000:00]-+-01.0 Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] Host Bridge
+-01.2 Advanced Micro Devices, Inc. [AMD] Geode LX AES Security Block
+-06.0 VIA Technologies, Inc. VT6105M [Rhine-III]
+-07.0 VIA Technologies, Inc. VT6105M [Rhine-III]
+-08.0 VIA Technologies, Inc. VT6105M [Rhine-III]
+-09.0 VIA Technologies, Inc. VT6105M [Rhine-III]
+-0e.0-[01]--+-00.0 VIA Technologies, Inc. VT6105M [Rhine-III]
| +-01.0 VIA Technologies, Inc. VT6105M [Rhine-III]
| +-02.0 VIA Technologies, Inc. VT6105M [Rhine-III]
| \-03.0 VIA Technologies, Inc. VT6105M [Rhine-III]
+-14.0 Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] ISA
+-14.2 Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] IDE
+-15.0 Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] OHC
\-15.1 Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] EHC
(identical)
> and a capture of 'lspci -vvv'.
Good boot (commit reverted):
00:01.0 Host bridge: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] Host Bridge (rev 33)
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] Host Bridge
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248, Cache Line Size: 32 bytes
00:01.2 Entertainment encryption device: Advanced Micro Devices, Inc. [AMD] Geode LX AES Security Block
Subsystem: Advanced Micro Devices, Inc. [AMD] Geode LX AES Security Block
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at a0000000 (32-bit, non-prefetchable) [size=16K]
Kernel driver in use: Geode LX AES
00:06.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e100 [size=256]
Region 1: Memory at a0004000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
00:07.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at e200 [size=256]
Region 1: Memory at a0004100 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
00:08.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at e300 [size=256]
Region 1: Memory at a0004200 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
00:09.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at e400 [size=256]
Region 1: Memory at a0004300 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
00:0e.0 PCI bridge: Texas Instruments PCI2250 PCI-to-PCI Bridge (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: a4000000-a7ffffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00:14.0 ISA bridge: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] ISA (rev 03)
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] ISA
Control: I/O+ Mem- BusMaster- SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: I/O ports at 6000 [size=8]
Region 1: I/O ports at 6100 [size=256]
Region 2: I/O ports at 6200 [size=512]
Kernel driver in use: cs5535-mfd
00:14.2 IDE interface: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] IDE (rev 01) (prog-if 80 [Master])
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] IDE
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
Region 4: I/O ports at e000 [size=16]
Kernel driver in use: pata_cs5536
00:15.0 USB controller: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] OHC (rev 02) (prog-if 10 [OHCI])
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] OHC
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 15
Region 0: Memory at a0005000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
00:15.1 USB controller: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] EHC (rev 02) (prog-if 20 [EHCI])
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] EHC
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 15
Region 0: Memory at a0006000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ehci-pci
01:00.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at a4000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
01:01.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at d100 [size=256]
Region 1: Memory at a4000100 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
01:02.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at d200 [size=256]
Region 1: Memory at a4000200 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
01:03.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at d300 [size=256]
Region 1: Memory at a4000300 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
Bad boot (pristine 3.18.5):
00:01.0 Host bridge: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] Host Bridge (rev 33)
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] Host Bridge
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248, Cache Line Size: 32 bytes
00:01.2 Entertainment encryption device: Advanced Micro Devices, Inc. [AMD] Geode LX AES Security Block
Subsystem: Advanced Micro Devices, Inc. [AMD] Geode LX AES Security Block
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at a0000000 (32-bit, non-prefetchable) [size=16K]
Kernel driver in use: Geode LX AES
00:06.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e100 [size=256]
Region 1: Memory at a0004000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
00:07.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at e200 [size=256]
Region 1: Memory at a0004100 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
00:08.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at e300 [size=256]
Region 1: Memory at a0004200 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
00:09.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at e400 [size=256]
Region 1: Memory at a0004300 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
00:0e.0 PCI bridge: Texas Instruments PCI2250 PCI-to-PCI Bridge (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: a4000000-a7ffffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00:14.0 ISA bridge: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] ISA (rev 03)
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] ISA
Control: I/O+ Mem- BusMaster- SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: I/O ports at 0000 [size=8]
Region 1: I/O ports at 0000
Region 2: I/O ports at 0000
Kernel driver in use: cs5535-mfd
00:14.2 IDE interface: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] IDE (rev 01) (prog-if 80 [Master])
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] IDE
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
Region 4: I/O ports at e000 [size=16]
Kernel driver in use: pata_cs5536
00:15.0 USB controller: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] OHC (rev 02) (prog-if 10 [OHCI])
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] OHC
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 15
Region 0: Memory at a0005000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
00:15.1 USB controller: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] EHC (rev 02) (prog-if 20 [EHCI])
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] EHC
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 15
Region 0: Memory at a0006000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ehci-pci
01:00.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at a4000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
01:01.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at d100 [size=256]
Region 1: Memory at a4000100 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
01:02.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at d200 [size=256]
Region 1: Memory at a4000200 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
01:03.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
Subsystem: VIA Technologies, Inc. Device 0106
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at d300 [size=256]
Region 1: Memory at a4000300 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
Diff:
--- /tmp/good-lspci 2015-02-02 17:33:14.373549639 +0000
+++ /tmp/bad-lspci 2015-02-02 17:35:15.263683424 +0000
@@ -84,9 +84,9 @@
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] ISA
Control: I/O+ Mem- BusMaster- SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
- Region 0: I/O ports at 6000 [size=8]
- Region 1: I/O ports at 6100 [size=256]
- Region 2: I/O ports at 6200 [size=512]
+ Region 0: I/O ports at 0000 [size=8]
+ Region 1: I/O ports at 0000
+ Region 2: I/O ports at 0000
Kernel driver in use: cs5535-mfd
00:14.2 IDE interface: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] IDE (rev 01) (prog-if 80 [Master])
i.e.
00:14.0 ISA bridge: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] ISA (rev 03)
Subsystem: Advanced Micro Devices, Inc. [AMD] CS5536 [Geode companion] ISA
Control: I/O+ Mem- BusMaster- SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: I/O ports at 6000 [size=8]
Region 1: I/O ports at 6100 [size=256]
Region 2: I/O ports at 6200 [size=512]
Kernel driver in use: cs5535-mfd
is broken. (Given that the IDE interface is behind it I'm fairly
surprised my disk worked at all!)
> I'll open a BZ for this issue tomorrow which we can use to attach the
> logs while tracking this down.
Thanks!
(hope this helps)
--
NULL && (void)
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/