Re: [PATCH 3/4] mmc: sdio: support switching to 1-bit before turning off clocks
From: NeilBrown
Date: Wed Mar 04 2015 - 00:29:11 EST
On Tue, 3 Mar 2015 14:53:55 -0800 Tony Lindgren <tony@xxxxxxxxxxx> wrote:
> * NeilBrown <neilb@xxxxxxx> [150223 18:47]:
> > According to section 7.1.2 of
> >
> > http://www.sandisk.com/media/File/OEM/Manuals/SD_SDIO_specsv1.pdf
> >
> > In the case where the interrupt mechanism is used to wake the host while
> > the card is in a low power state (i.e. no clocks), Both the card and the
> > host shall be placed into the 1-bit SD mode prior to stopping the clock.
> >
> > This is particularly important for the Marvell "libertas" wifi chip
> > in the GTA04. While in 4-bit mode it will only signal an interrupt
> > when the clock is running (which is why setting CLKEXTFREE is
> > important).
> > In 1-bit mode, the interrupt is asynchronous (explained in OMAP3
> > TRM description of the CIRQ flag to MMCHS_STAT:
> >
> > In 1-bit mode, interrupt source is asynchronous (can be a source of
> > asynchronous wakeup).
> > In 4-bit mode, interrupt source is sampled during the interrupt
> > cycle.
> >
> > )
> >
> > It is awkward to simply set 1-bit mode in ->runtime_suspend
> > as that will call mmc_set_ios which calls ops->set_ios(),
> > which will likely call pm_runtime_get_sync(), on the device that
> > is currently suspending. This deadlocks.
> >
> > So:
> > - create a work_struct to schedule setting of 1-bit mode
> > - introduce an 'sdio_narrowed' state flag which transitions:
> > 0 (normal) -> 1 (convert to 1-bit pending) ->
> > 2 (have switch to 1-bit mode) -> 0 (normal)
> > - create a function mmc_sdio_want_no_clocks() which can be called
> > when the driver wants to turn off clocks (presumably after an
> > idle timeout). This either succeeds (in 1-bit mode) or fails
> > and schedules the work to switch to 1-bit mode.
> > - when the host is claimed, if sdio_narrowed is 2, restore the
> > 4-bit bus
> > - When the host is released, if sdio_narrowed is 1, then some
> > caller other than our worker claimed the host first, so
> > clear sdio_narrowed.
> >
> > This all allows a graceful and race-free switch to 1-bit mode
> > before switching off the clocks, if SDIO interrupts are enabled.
> >
> > A host should call mmc_sdio_want_no_clocks() when about to turn off
> > clocks if sdio interrupts are enabled, and the ->disable() function
> > should not use a timeout (pm_runtime_put_autosuspend) if
> > ->sdio_narrowed is 2.
>
> Wow! A mystery finally solved for why libertas_sdio using devices
> like overo won't work for the wakeirqs.. The interface has to be
> in 1-bit mode for libertas to produce any SDIO interrupts..
>
> Below is a patch enabling some more SDIO wakeirqs. Seems to work
> on overo now too :) So tor the whole series, please feel free to
> add:
>
> Tested-by: Tony Lindgren <tony@xxxxxxxxxxx>
Thanks a lot!
>
> 8< -------------------
> From: Tony Lindgren <tony@xxxxxxxxxxx>
> Date: Thu, 26 Feb 2015 16:16:03 -0800
> Subject: [PATCH] ARM: dts: Fix omap3 SDIO wakeirqs for devices using sdio_libertas
>
> Turns out the the MMC interface needs to be in 1-bit mode for the
> libertas card to send any SDIO interrupts as pointed out by
> NeilBrown <neilb@xxxxxxx>. Now that the MMC framework is getting
> fixed for setting 1-bit mode for idle, we can enable SDIO wakeirqs
> for libertas using devices too.
>
> Cc: Andreas Fenkart <afenkart@xxxxxxxxx>
> Cc: Ash Charles <ash@xxxxxxxxxxx>
> Cc: Florian Vaussard <florian.vaussard@xxxxxxx>
> Cc: NeilBrown <neil@xxxxxxxxxx>
> Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
>
> --- a/arch/arm/boot/dts/omap3-gta04.dtsi
> +++ b/arch/arm/boot/dts/omap3-gta04.dtsi
> @@ -367,6 +367,7 @@
> };
>
> &mmc2 {
> + interrupts-extended = <&intc 86 &omap3_pmx_core 0x12e>;
> vmmc-supply = <&vaux4>;
> bus-width = <4>;
> ti,non-removable;
I had
+ interrupts-extended = <&intc 86 &gpio5 5 0>; /* GPIO_133 */
+ pinctrl-names = "default", "idle";
+ pinctrl-0 = <&mmc2_pins>;
+ pinctrl-1 = <&mmc2_cirq_pin>;
together with
+ mmc2_cirq_pin: pinmux_cirq_pin {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE4)
+ >;
+ };
+
and a longer definition for mmc2_pins.
Is that one line reconfigure the pin on demand? How does that work?
Thanks,
NeilBrown
Attachment:
pgpf0_DOF2gtE.pgp
Description: OpenPGP digital signature