Re: [PATCH/RFC v12 10/19] DT: Add documentation for the mfd Maxim max77693

[Sakari Ailus]

Hi Jacek,

On Wed, Mar 04, 2015 at 05:14:31PM +0100, Jacek Anaszewski wrote:
> This patch adds device tree binding documentation for
> the flash cell of the Maxim max77693 multifunctional device.
> 
> Signed-off-by: Jacek Anaszewski <j.anaszewski@xxxxxxxxxxx>
> Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
> Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
> Cc: Lee Jones <lee.jones@xxxxxxxxxx>
> Cc: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
> Cc: Bryan Wu <cooloney@xxxxxxxxx>
> Cc: Richard Purdie <rpurdie@xxxxxxxxx>
> ---
>  Documentation/devicetree/bindings/mfd/max77693.txt |   61 ++++++++++++++++++++
>  1 file changed, 61 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
> index 38e6440..ab8fbd5 100644
> --- a/Documentation/devicetree/bindings/mfd/max77693.txt
> +++ b/Documentation/devicetree/bindings/mfd/max77693.txt
> @@ -76,7 +76,53 @@ Optional properties:
>      Valid values: 4300000, 4700000, 4800000, 4900000
>      Default: 4300000
>  
> +- led : the LED submodule device node
> +
> +There are two LED outputs available - FLED1 and FLED2. Each of them can
> +control a separate LED or they can be connected together to double
> +the maximum current for a single connected LED. One LED is represented
> +by one child node.
> +
> +Required properties:
> +- compatible : Must be "maxim,max77693-led".
> +
> +Optional properties:
> +- maxim,trigger-type : Flash trigger type.
> +	Possible trigger types:
> +		LEDS_TRIG_TYPE_EDGE (0) - Rising edge of the signal triggers
> +			the flash,
> +		LEDS_TRIG_TYPE_LEVEL (1) - Strobe pulse length controls duration
> +			of the flash.
> +- maxim,boost-mode :
> +	In boost mode the device can produce up to 1.2A of total current
> +	on both outputs. The maximum current on each output is reduced
> +	to 625mA then. If not enabled explicitly, boost setting defaults to
> +	LEDS_BOOST_FIXED in case both current sources are used.
> +	Possible values:
> +		LEDS_BOOST_OFF (0) - no boost,
> +		LEDS_BOOST_ADAPTIVE (1) - adaptive mode,
> +		LEDS_BOOST_FIXED (2) - fixed mode.
> +- maxim,boost-mvout : Output voltage of the boost module in millivolts.
> +- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired
> +	if chip estimates that system voltage could drop below this level due
> +	to flash power consumption.
> +
> +Required properties of the LED child node:
> +- label : see Documentation/devicetree/bindings/leds/common.txt

According to ePAPR, label is "a human readable string describing a device".
There's no requirement that this would be unique, for instance. If you have
a camera flash LED, there's necessarily no meaningful label for it, as it
doesn't really tell the user anything (vs. HDD activity LED, for instance).

I think I'd make this optional.

What comes to entity naming in Media controller, the label isn't enough. As
we haven't yet fully agreed on how to name the entities in the future, I'd
propose sticking to current practices: chip name (and optional numerical LED
ID) followed by the I2C address. The name should be specified by the driver.

Do you have other than I2C busses required by the current drivers?

> +- led-sources : see Documentation/devicetree/bindings/leds/common.txt;
> +		device current output identifiers: 0 - FLED1, 1 - FLED2
> +
> +Optional properties of the LED child node:
> +- max-microamp : see Documentation/devicetree/bindings/leds/common.txt
> +		Range: 15625 - 250000
> +- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
> +		Range: 15625 - 1000000
> +- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
> +		Range: 62500 - 1000000
> +
>  Example:
> +#include <dt-bindings/leds/max77693.h>
> +
>  	max77693@66 {
>  		compatible = "maxim,max77693";
>  		reg = <0x66>;
> @@ -117,5 +163,20 @@ Example:
>  			maxim,thermal-regulation-celsius = <75>;
>  			maxim,battery-overcurrent-microamp = <3000000>;
>  			maxim,charge-input-threshold-microvolt = <4300000>;
> +
> +		led {
> +			compatible = "maxim,max77693-led";
> +			maxim,trigger-type = <LEDS_TRIG_TYPE_LEVEL>;
> +			maxim,boost-mode = <LEDS_BOOST_FIXED>;
> +			maxim,boost-mvout = <5000>;
> +			maxim,mvsys-min = <2400>;
> +
> +			camera_flash: flash-led {
> +				label = "max77693-flash1";
> +				led-sources = <0>, <1>;
> +				max-microamp = <500000>;
> +				flash-max-microamp = <1250000>;
> +				flash-timeout-us = <1000000>;
> +			};
>  		};
>  	};

-- 
Kind regards,

Sakari Ailus
e-mail: sakari.ailus@xxxxxx	XMPP: sailus@xxxxxxxxxxxxxx
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/