Re: [PATCH v4 3/3] leds: Add ktd2692 flash LED driver
From: Ingi Kim
Date: Thu Mar 26 2015 - 00:56:56 EST
Hi Sakari,
Thanks for the review
On 2015ë 03ì 25ì 22:53, Sakari Ailus wrote:
> Hi Ingi,
>
> Thank you for the patch.
>
> On Wed, Mar 25, 2015 at 10:30:44AM +0900, Ingi Kim wrote:
>> This patch adds a driver to support the ktd2692 flash LEDs.
>> ktd2692 can control flash current by ExpressWire interface.
>>
>> Signed-off-by: Ingi Kim <ingi2.kim@xxxxxxxxxxx>
>> ---
>> drivers/leds/Kconfig | 9 +
>> drivers/leds/Makefile | 1 +
>> drivers/leds/leds-ktd2692.c | 412 ++++++++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 422 insertions(+)
>> create mode 100644 drivers/leds/leds-ktd2692.c
>>
>> diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
>> index 25b320d..9311cfc4 100644
>> --- a/drivers/leds/Kconfig
>> +++ b/drivers/leds/Kconfig
>> @@ -498,6 +498,15 @@ config LEDS_MENF21BMC
>> This driver can also be built as a module. If so the module
>> will be called leds-menf21bmc.
>>
>> +config LEDS_KTD2692
>> + tristate "Flash LED support for the KTD2692 Driver"
>
> Does ktd2692 act as something else as well? If not, how about "KTD2692 LED
> flash support"?
>
Right, KTD2692 driver acts just for flash led.
>> + depends on LEDS_CLASS_FLASH && GPIOLIB
>> + help
>> + This option enables support for the KTD2692 connected through
>> + ExpressWire Interface. Say Y to enabled these.
>> + It depends on LEDS_CLASS_FLASH for using flash led (strobe) and
>> + GPIOLIB for using gpio pin to control Expresswire interface
>
> The dependencies are shown by make *config, I would drop them from here.
>
Did you mean help message about dependencies? or config (LEDS_CLASS_FLASH, GPIOLIB)
if you mean latter, I don't know exactly what you say.
if it wasn't, I should drop superfluous help message
>> +
>> comment "LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)"
>>
>> config LEDS_BLINKM
>> diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
>> index cbba921..289513b 100644
>> --- a/drivers/leds/Makefile
>> +++ b/drivers/leds/Makefile
>> @@ -58,6 +58,7 @@ obj-$(CONFIG_LEDS_BLINKM) += leds-blinkm.o
>> obj-$(CONFIG_LEDS_SYSCON) += leds-syscon.o
>> obj-$(CONFIG_LEDS_VERSATILE) += leds-versatile.o
>> obj-$(CONFIG_LEDS_MENF21BMC) += leds-menf21bmc.o
>> +obj-$(CONFIG_LEDS_KTD2692) += leds-ktd2692.o
>>
>> # LED SPI Drivers
>> obj-$(CONFIG_LEDS_DAC124S085) += leds-dac124s085.o
>> diff --git a/drivers/leds/leds-ktd2692.c b/drivers/leds/leds-ktd2692.c
>> new file mode 100644
>> index 0000000..c31ec9d
>> --- /dev/null
>> +++ b/drivers/leds/leds-ktd2692.c
>> @@ -0,0 +1,412 @@
>> +/*
>> + * LED driver : leds-ktd2692.c
>> + *
>> + * Copyright (C) 2015 Samsung Electronics
>> + * Ingi Kim <ingi2.kim@xxxxxxxxxxx>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +#include <linux/delay.h>
>> +#include <linux/err.h>
>> +#include <linux/led-class-flash.h>
>> +#include <linux/module.h>
>> +#include <linux/mutex.h>
>> +#include <linux/of_gpio.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regulator/consumer.h>
>> +#include <linux/workqueue.h>
>> +
>> +#define GET_BIT(bit, val) (((val) >> (bit)) & 0x01)
>> +
>> +/* Value related the flash mode */
>> +#define KTD2692_FLASH_MODE_TIMEOUT_LEVELS 8
>> +#define KTD2692_FLASH_MODE_TIMEOUT_DISABLE 0
>> +#define KTD2692_FLASH_MODE_TIMEOUT_DEFAULT_US 1049000
>> +#define KTD2692_FLASH_MODE_TIMEOUT_MAX_US 1835000
>> +#define KTD2692_FLASH_MODE_CURR_PERCENT(x) (((x) * 16) / 100)
>> +
>> +/* Macro for getting offset of flash timeout */
>> +#define GET_TIMEOUT_OFFSET(timeout, step) ((timeout) / (step))
>> +
>> +/* Adjust a multiple of brightness */
>> +#define KTD2692_BRIGHTNESS_RANGE_255_TO_16(x) (((x) >> 4) & 0x0F)
>> +#define KTD2692_BRIGHTNESS_RANGE_255_TO_8(x) (((x) >> 5) & 0x0F)
>> +#define KTD2692_BRIGHTNESS_RANGE_255_TO_4(x) (((x) >> 6) & 0x0F)
>> +
>> +/* Base register address */
>> +#define KTD2692_REG_LVP_BASE 0x00
>> +#define KTD2692_REG_FLASH_TIMEOUT_BASE 0x20
>> +#define KTD2692_REG_MIN_CURRENT_SET_BASE 0x40
>> +#define KTD2692_REG_MOVIE_CURRENT_BASE 0x60
>> +#define KTD2692_REG_FLASH_CURRENT_BASE 0x80
>> +#define KTD2692_REG_MODE_BASE 0xA0
>> +
>> +/* Set bit coding time for expresswire interface */
>> +#define KTD2692_TIME_RESET_US 700
>> +#define KTD2692_TIME_DATA_START_TIME_US 10
>> +#define KTD2692_TIME_HIGH_END_OF_DATA_US 350
>> +#define KTD2692_TIME_LOW_END_OF_DATA_US 10
>> +#define KTD2692_TIME_SHORT_BITSET_US 4
>> +#define KTD2692_TIME_LONG_BITSET_US 12
>> +
>> +/* KTD2692 default length of name */
>> +#define KTD2692_NAME_LENGTH 20
>> +
>> +/* KTD2692 default name */
>> +#define KTD2692_DEFAULT_NAME "ktd2692"
>> +
>> +enum ktd2692_bitset {
>> + KTD2692_LOW = 0,
>> + KTD2692_HIGH,
>> +};
>> +
>> +/* Movie / Flash Mode Control */
>> +enum ktd2692_led_mode {
>> + KTD2692_MODE_DISABLE = 0, /* default */
>> + KTD2692_MODE_MOVIE,
>> + KTD2692_MODE_FLASH,
>> +};
>> +
>> +struct ktd2692_context {
>> + /* Related LED Flash class device */
>> + struct led_classdev_flash fled_cdev;
>> +
>> + struct mutex lock;
>> + struct regulator *regulator;
>> + struct work_struct work_brightness_set;
>> +
>> + int aux_gpio;
>> + int ctrl_gpio;
>> +
>> + enum ktd2692_led_mode mode;
>> + enum led_brightness torch_brightness;
>> +};
>> +
>> +static struct ktd2692_context *fled_cdev_to_led(
>> + struct led_classdev_flash *fled_cdev)
>> +{
>> + return container_of(fled_cdev, struct ktd2692_context, fled_cdev);
>> +}
>> +
>> +static void ktd2692_led_regulator_enable(struct ktd2692_context *led)
>> +{
>> + struct led_classdev_flash *fled_cdev = &led->fled_cdev;
>> + struct led_classdev *led_cdev = &fled_cdev->led_cdev;
>> + int ret;
>> +
>> + if (regulator_is_enabled(led->regulator) > 0)
>> + return;
>
> What's the purpose of this? Why not to just call regulator_enable() instead?
>
> This way you could easily mess up with other users of the same regulator.
>
I want to harmonize all APIs in here...
but I'd better simplify code if it would make a mess
>> +
>> + ret = regulator_enable(led->regulator);
>> + if (ret)
>> + dev_err(led_cdev->dev, "Failed to enable vin:%d\n", ret);
>> +}
>> +
>> +static void ktd2692_led_regulator_disable(struct ktd2692_context *led)
>> +{
>> + struct led_classdev_flash *fled_cdev = &led->fled_cdev;
>> + struct led_classdev *led_cdev = &fled_cdev->led_cdev;
>> + int ret;
>> +
>> + if (!regulator_is_enabled(led->regulator))
>> + return;
>> +
>> + ret = regulator_disable(led->regulator);
>> + if (ret)
>> + dev_err(led_cdev->dev, "Failed to disable vin:%d\n", ret);
>> +}
>> +
>> +static void ktd2692_expresswire_start(struct ktd2692_context *led)
>> +{
>> + gpio_set_value(led->ctrl_gpio, KTD2692_HIGH);
>> + udelay(KTD2692_TIME_DATA_START_TIME_US);
>> +}
>> +
>> +static void ktd2692_expresswire_reset(struct ktd2692_context *led)
>> +{
>> + gpio_set_value(led->ctrl_gpio, KTD2692_LOW);
>> + udelay(KTD2692_TIME_RESET_US);
>> +}
>> +
>> +static void ktd2692_expresswire_end(struct ktd2692_context *led)
>> +{
>> + gpio_set_value(led->ctrl_gpio, KTD2692_LOW);
>> + udelay(KTD2692_TIME_LOW_END_OF_DATA_US);
>> + gpio_set_value(led->ctrl_gpio, KTD2692_HIGH);
>> + udelay(KTD2692_TIME_HIGH_END_OF_DATA_US);
>> +}
>> +
>> +static void ktd2692_expresswire_set_bit(struct ktd2692_context *led, bool bit)
>> +{
>> + if (bit) {
>> + gpio_set_value(led->ctrl_gpio, KTD2692_LOW);
>> + udelay(KTD2692_TIME_SHORT_BITSET_US);
>> + gpio_set_value(led->ctrl_gpio, KTD2692_HIGH);
>> + udelay(KTD2692_TIME_LONG_BITSET_US);
>> + } else {
>> + gpio_set_value(led->ctrl_gpio, KTD2692_LOW);
>> + udelay(KTD2692_TIME_LONG_BITSET_US);
>> + gpio_set_value(led->ctrl_gpio, KTD2692_HIGH);
>> + udelay(KTD2692_TIME_SHORT_BITSET_US);
>> + }
>> +}
>> +
>> +static void ktd2692_expresswire_write(struct ktd2692_context *led, u8 value)
>> +{
>> + int i;
>> +
>> + ktd2692_expresswire_start(led);
>> + for (i = 7; i >= 0; i--)
>> + ktd2692_expresswire_set_bit(led, GET_BIT(i, value));
>
> I think this would be cleaner as:
>
> value & BIT(i)
>
> Casting an integer as bool will result in true if it's non-zero, so you
> don't need to cast.
>
Thanks for good suggestion
I'll try
>> + ktd2692_expresswire_end(led);
>> +}
>> +
>> +static void ktd2692_brightness_set(struct ktd2692_context *led,
>> + enum led_brightness brightness)
>> +{
>> + mutex_lock(&led->lock);
>> +
>> + if (brightness == LED_OFF) {
>> + led->mode = KTD2692_MODE_DISABLE;
>> + gpio_set_value(led->aux_gpio, KTD2692_LOW);
>> + goto out;
>> + }
>> +
>> + ktd2692_expresswire_write(led, KTD2692_REG_MOVIE_CURRENT_BASE |
>> + KTD2692_BRIGHTNESS_RANGE_255_TO_8(brightness));
>> + led->mode = KTD2692_MODE_MOVIE;
>> +
>> +out:
>> + ktd2692_expresswire_write(led, led->mode | KTD2692_REG_MODE_BASE);
>> + mutex_unlock(&led->lock);
>> +}
>> +
>> +static void ktd2692_brightness_set_work(struct work_struct *work)
>> +{
>> + struct ktd2692_context *led =
>> + container_of(work, struct ktd2692_context, work_brightness_set);
>> +
>> + ktd2692_brightness_set(led, led->torch_brightness);
>> +}
>> +
>> +static void ktd2692_led_brightness_set(struct led_classdev *led_cdev,
>> + enum led_brightness brightness)
>> +{
>> + struct led_classdev_flash *fled_cdev = lcdev_to_flcdev(led_cdev);
>> + struct ktd2692_context *led = fled_cdev_to_led(fled_cdev);
>> +
>> + led->torch_brightness = brightness;
>> + schedule_work(&led->work_brightness_set);
>> +}
>> +
>> +static int ktd2692_led_brightness_set_sync(struct led_classdev *led_cdev,
>> + enum led_brightness brightness)
>> +{
>> + struct led_classdev_flash *fled_cdev = lcdev_to_flcdev(led_cdev);
>> + struct ktd2692_context *led = fled_cdev_to_led(fled_cdev);
>> +
>> + ktd2692_brightness_set(led, brightness);
>> +
>> + return 0;
>> +}
>> +
>> +static int ktd2692_led_flash_strobe_set(struct led_classdev_flash *fled_cdev,
>> + bool state)
>> +{
>> + struct ktd2692_context *led = fled_cdev_to_led(fled_cdev);
>> + struct led_flash_setting *timeout = &fled_cdev->timeout;
>> + u32 flash_tm_reg;
>> +
>> + mutex_lock(&led->lock);
>> +
>> + if (state == 0) {
>> + led->mode = KTD2692_MODE_DISABLE;
>> + gpio_set_value(led->aux_gpio, KTD2692_LOW);
>> + goto done;
>> + }
>> +
>> + flash_tm_reg = GET_TIMEOUT_OFFSET(timeout->val, timeout->step);
>> + ktd2692_expresswire_write(led, flash_tm_reg
>> + | KTD2692_REG_FLASH_TIMEOUT_BASE);
>> +
>> + led->mode = KTD2692_MODE_FLASH;
>> + gpio_set_value(led->aux_gpio, KTD2692_HIGH);
>> +
>> +done:
>> + ktd2692_expresswire_write(led, led->mode | KTD2692_REG_MODE_BASE);
>> +
>> + fled_cdev->led_cdev.brightness = LED_OFF;
>> + led->mode = KTD2692_MODE_DISABLE;
>> +
>> + mutex_unlock(&led->lock);
>> +
>> + return 0;
>> +}
>> +
>> +static int ktd2692_led_flash_timeout_set(struct led_classdev_flash *fled_cdev,
>> + u32 timeout)
>> +{
>> + return 0;
>> +}
>> +
>> +static void ktd2692_init_flash_timeout(u32 flash_timeout_us,
>> + struct led_flash_setting *setting)
>> +{
>> + setting->min = KTD2692_FLASH_MODE_TIMEOUT_DISABLE;
>> + setting->max = KTD2692_FLASH_MODE_TIMEOUT_MAX_US;
>> + setting->step = KTD2692_FLASH_MODE_TIMEOUT_MAX_US
>> + / (KTD2692_FLASH_MODE_TIMEOUT_LEVELS - 1);
>> + setting->val = flash_timeout_us;
>> +}
>> +
>> +static void ktd2692_setup(struct ktd2692_context *led)
>> +{
>> + led->mode = KTD2692_MODE_DISABLE;
>> + ktd2692_expresswire_reset(led);
>> + gpio_set_value(led->aux_gpio, KTD2692_LOW);
>> +
>> + ktd2692_expresswire_write(led, KTD2692_FLASH_MODE_CURR_PERCENT(45)
>> + | KTD2692_REG_FLASH_CURRENT_BASE);
>> +}
>> +
>> +static int ktd2692_parse_dt(struct ktd2692_context *led, struct device *dev,
>> + u32 *flash_timeout_us)
>> +{
>> + struct device_node *np = dev->of_node;
>> +
>> + int ret;
>> +
>> + led->ctrl_gpio = of_get_named_gpio(np, "ctrl-gpio", 0);
>> + if (!gpio_is_valid(led->ctrl_gpio)) {
>> + dev_err(dev, "no ctrl-gpio property found\n");
>> + return -EINVAL;
>> + }
>> +
>> + led->aux_gpio = of_get_named_gpio(np, "aux-gpio", 0);
>> + if (!gpio_is_valid(led->aux_gpio)) {
>> + dev_err(dev, "no aux-gpio property found\n");
>> + return -EINVAL;
>> + }
>> +
>> + ret = devm_gpio_request_one(dev, led->ctrl_gpio,
>> + GPIOF_OPEN_SOURCE, "ctrl-gpio");
>> + if (ret) {
>> + dev_err(dev, "failed to request ctrl-gpio %d error %d\n",
>> + led->ctrl_gpio, ret);
>> + return ret;
>> + }
>> +
>> + ret = devm_gpio_request_one(dev, led->aux_gpio,
>> + GPIOF_OPEN_SOURCE, "aux-gpio");
>> + if (ret) {
>> + dev_err(dev, "failed to request aux-gpio %d error %d\n",
>> + led->aux_gpio, ret);
>> + return ret;
>> + }
>> +
>> + ret = of_property_read_u32(np, "flash-timeout-us", flash_timeout_us);
>> + /* default setting */
>> + if (ret)
>> + *flash_timeout_us = KTD2692_FLASH_MODE_TIMEOUT_DEFAULT_US;
>> +
>> + return 0;
>> +}
>> +
>> +static const struct led_flash_ops flash_ops = {
>> + .strobe_set = ktd2692_led_flash_strobe_set,
>> + .timeout_set = ktd2692_led_flash_timeout_set,
>> +};
>> +
>> +static int ktd2692_probe(struct platform_device *pdev)
>> +{
>> + struct ktd2692_context *led;
>> + struct led_classdev *led_cdev;
>> + struct led_classdev_flash *fled_cdev;
>> + struct led_flash_setting flash_timeout;
>> + u32 flash_timeout_us;
>> + int ret;
>> +
>> + led = devm_kzalloc(&pdev->dev, sizeof(*led), GFP_KERNEL);
>> + if (!led)
>> + return -ENOMEM;
>> +
>> + if (!pdev->dev.of_node)
>> + return -ENXIO;
>> +
>> + fled_cdev = &led->fled_cdev;
>> + led_cdev = &fled_cdev->led_cdev;
>> +
>> + ret = ktd2692_parse_dt(led, &pdev->dev, &flash_timeout_us);
>> + if (ret)
>> + return ret;
>> +
>> + led->regulator = devm_regulator_get(&pdev->dev, "vin");
>> + if (IS_ERR(led->regulator)) {
>> + dev_err(&pdev->dev, "regulator get failed\n");
>> + return PTR_ERR(led->regulator);
>> + }
>> +
>> + ktd2692_init_flash_timeout(flash_timeout_us, &flash_timeout);
>> +
>> + fled_cdev->timeout = flash_timeout;
>> + fled_cdev->ops = &flash_ops;
>> +
>> + led_cdev->name = KTD2692_DEFAULT_NAME;
>> + led_cdev->brightness_set = ktd2692_led_brightness_set;
>> + led_cdev->brightness_set_sync = ktd2692_led_brightness_set_sync;
>> + led_cdev->flags |= LED_CORE_SUSPENDRESUME;
>> + led_cdev->flags |= LED_DEV_CAP_FLASH;
>
> You could unify the above two lines.
>
Is it better to unify code than separate?
>> +
>> + mutex_init(&led->lock);
>> + INIT_WORK(&led->work_brightness_set, ktd2692_brightness_set_work);
>> +
>> + platform_set_drvdata(pdev, led);
>> +
>> + ret = led_classdev_flash_register(&pdev->dev, fled_cdev);
>> + if (ret) {
>> + dev_err(&pdev->dev, "can't register LED %s\n", led_cdev->name);
>
> You should do mutex_destroy() here.
>
Right. I should do
Thanks
>> + cancel_work_sync(&led->work_brightness_set);
>> + return ret;
>> + }
>> +
>
> This is a LED flash device. Do you intend to add support for the V4L2 flash
> API as well?
>
I hope :-)
maybe I would support extend version later
>> + ktd2692_setup(led);
>> + ktd2692_led_regulator_enable(led);
>
> Hmm. I guess the regulator was already enabled, assuming you have tested
> this. :-)
>
Oh, I'll check.
Isn't it necessary to use this API if the regulator was enabled?
>> +
>> + return 0;
>> +}
>> +
>> +static int ktd2692_remove(struct platform_device *pdev)
>> +{
>> + struct ktd2692_context *led = platform_get_drvdata(pdev);
>> +
>> + ktd2692_led_regulator_disable(led);
>> + led_classdev_flash_unregister(&led->fled_cdev);
>> + cancel_work_sync(&led->work_brightness_set);
>> +
>> + mutex_destroy(&led->lock);
>> +
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id ktd2692_match[] = {
>> + { .compatible = "kinetic,ktd2692", },
>> + { /* sentinel */ },
>> +};
>> +
>> +static struct platform_driver ktd2692_driver = {
>> + .driver = {
>> + .name = "leds-ktd2692",
>> + .of_match_table = ktd2692_match,
>> + },
>> + .probe = ktd2692_probe,
>> + .remove = ktd2692_remove,
>> +};
>> +
>> +module_platform_driver(ktd2692_driver);
>> +
>> +MODULE_AUTHOR("Ingi Kim <ingi2.kim@xxxxxxxxxxx>");
>> +MODULE_DESCRIPTION("Kinetic KTD2692 LED driver");
>> +MODULE_LICENSE("GPL v2");
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/