[PATCH 5/5] usb: add pxa1928 ehci support

[Rob Herring]

Add platform driver for Marvell PXA1928 SOC. This is different from the
mv-ehci driver in that it uses the generic phy framework, uses DT, does
not use platform_data, is host only, and has a specific HSIC PHY and
controller initialization handshake.

Signed-off-by: Rob Herring <robh@xxxxxxxxxx>
Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
Cc: Alan Stern <stern@xxxxxxxxxxxxxxxxxxx>
Cc: linux-usb@xxxxxxxxxxxxxxx
---
 drivers/usb/host/Kconfig      |  15 ++-
 drivers/usb/host/Makefile     |   1 +
 drivers/usb/host/ehci-mv-of.c | 243 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 258 insertions(+), 1 deletion(-)
 create mode 100644 drivers/usb/host/ehci-mv-of.c

diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 197a6a3..4d8cfbc 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -251,6 +251,19 @@ config USB_EHCI_MV
 	  Dova, Armada 370 and Armada XP. See "Support for Marvell EBU
 	  on-chip EHCI USB controller" for those.
 
+config USB_EHCI_MV_OF
+	bool "EHCI OF support for Marvell PXA/MMP USB controller"
+	depends on (ARCH_PXA || ARCH_MMP)
+	select USB_EHCI_ROOT_HUB_TT
+	---help---
+	  Enables support for Marvell (including PXA and MMP series) on-chip
+	  USB SPH and OTG controller. SPH is a single port host, and it can
+	  only be EHCI host. OTG is controller that can switch to host mode.
+	  Note that this driver will not work on Marvell's other EHCI
+	  controller used by the EBU-type SoCs including Orion, Kirkwood,
+	  Dova, Armada 370 and Armada XP. See "Support for Marvell EBU
+	  on-chip EHCI USB controller" for those.
+
 config USB_W90X900_EHCI
 	tristate "W90X900(W90P910) EHCI support"
 	depends on ARCH_W90X900
@@ -663,7 +676,7 @@ config USB_SL811_HCD
 	help
 	  The SL811HS is a single-port USB controller that supports either
 	  host side or peripheral side roles.  Enable this option if your
-	  board has this chip, and you want to use it as a host controller. 
+	  board has this chip, and you want to use it as a host controller.
 	  If unsure, say N.
 
 	  To compile this driver as a module, choose M here: the
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 65b0b6a..5ed93ff 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -32,6 +32,7 @@ obj-$(CONFIG_USB_XHCI_PLATFORM) += xhci-plat-hcd.o
 obj-$(CONFIG_USB_EHCI_HCD)	+= ehci-hcd.o
 obj-$(CONFIG_USB_EHCI_PCI)	+= ehci-pci.o
 obj-$(CONFIG_USB_EHCI_HCD_PLATFORM)	+= ehci-platform.o
+obj-$(CONFIG_USB_EHCI_MV_OF)	+= ehci-mv-of.o
 obj-$(CONFIG_USB_EHCI_MXC)	+= ehci-mxc.o
 obj-$(CONFIG_USB_EHCI_HCD_OMAP)	+= ehci-omap.o
 obj-$(CONFIG_USB_EHCI_HCD_ORION)	+= ehci-orion.o
diff --git a/drivers/usb/host/ehci-mv-of.c b/drivers/usb/host/ehci-mv-of.c
new file mode 100644
index 0000000..3783299
--- /dev/null
+++ b/drivers/usb/host/ehci-mv-of.c
@@ -0,0 +1,243 @@
+/*
+ * Copyright (C) 2015 Linaro, Ltd.
+ * Rob Herring <robh@xxxxxxxxxx>
+ *
+ * Based on vendor driver modifications to ehci-mv.c:
+ * Copyright (C) 2011 Marvell International Ltd. All rights reserved.
+ * Author: Chao Xie <chao.xie@xxxxxxxxxxx>
+ *        Neil Zhang <zhangwm@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/phy/phy.h>
+#include <linux/err.h>
+#include <linux/usb.h>
+#include <linux/usb/hcd.h>
+
+#include "ehci.h"
+
+struct ehci_hcd_mv {
+	struct usb_hcd *hcd;
+	struct phy *phy;
+	struct clk *clk;
+};
+
+#define hcd_to_mv_priv(h) ((struct ehci_hcd_mv *)hcd_to_ehci(h)->priv)
+
+static struct hc_driver ehci_mv_hc_driver;
+
+static bool wait_for_reg(void __iomem *reg, u32 mask, unsigned long timeout)
+{
+	timeout += jiffies;
+	while (time_is_after_eq_jiffies(timeout)) {
+		if ((readl(reg) & mask) == mask)
+			return true;
+		msleep(1);
+	}
+	return false;
+}
+
+static int mv_ehci_enable(struct ehci_hcd_mv *ehci_mv)
+{
+	struct ehci_hcd *ehci = hcd_to_ehci(ehci_mv->hcd);
+	struct ehci_regs *ehci_regs = ehci->regs;
+	int retval;
+	u32 status;
+
+	/* enable port power and reserved bit 25 */
+	status = __raw_readl(&ehci_regs->port_status[0]);
+	status |= (PORT_POWER) | (1 << 25);
+	/* Clear bits 30:31 for HSIC to be enabled */
+	status &= ~(0x3 << 30);
+	__raw_writel(status, &ehci_regs->port_status[0]);
+
+	/* test mode: force enable hs */
+	status = __raw_readl(&ehci_regs->port_status[0]);
+	status &= ~(0xf << 16);
+	status |= (0x5 << 16);
+	__raw_writel(status, &ehci_regs->port_status[0]);
+
+	/* disable test mode */
+	status = __raw_readl(&ehci_regs->port_status[0]);
+	status &= ~(0xf << 16);
+	__raw_writel(status, &ehci_regs->port_status[0]);
+
+	retval =  phy_power_on(ehci_mv->hcd->phy);
+	if (retval)
+		return retval;
+
+	/* issue port reset */
+	status = __raw_readl(&ehci_regs->port_status[0]);
+	status |= PORT_RESET;
+	status &= ~PORT_PE;
+	__raw_writel(status, &ehci_regs->port_status[0]);
+
+	/* check reset done */
+	if (!wait_for_reg(&ehci_regs->port_status[0], PORT_RESET, HZ / 10)) {
+		pr_err("HSIC port reset not done: port_status 0x%x\n", status);
+		return -ETIMEDOUT;
+	}
+	return 0;
+}
+
+static int mv_ehci_probe(struct platform_device *pdev)
+{
+	struct usb_hcd *hcd;
+	struct ehci_hcd *ehci;
+	struct ehci_hcd_mv *ehci_mv;
+	struct resource *r;
+	int retval = -ENODEV;
+
+	hcd = usb_create_hcd(&ehci_mv_hc_driver, &pdev->dev, "mv ehci");
+	if (!hcd)
+		return -ENOMEM;
+	ehci = hcd_to_ehci(hcd);
+	ehci_mv = hcd_to_mv_priv(hcd);
+	ehci_mv->hcd = hcd;
+
+	platform_set_drvdata(pdev, ehci_mv);
+
+	ehci_mv->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(ehci_mv->clk)) {
+		dev_err(&pdev->dev, "error getting clock\n");
+		retval = PTR_ERR(ehci_mv->clk);
+		goto err_put_hcd;
+	}
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	ehci->caps = devm_ioremap_resource(&pdev->dev, r);
+	if (IS_ERR(ehci->caps)) {
+		retval = PTR_ERR(ehci->caps);
+		goto err_put_hcd;
+	}
+
+	hcd->phy = devm_of_phy_get(&pdev->dev, pdev->dev.of_node, NULL);
+	if (IS_ERR_OR_NULL(hcd->phy)) {
+		retval = PTR_ERR(hcd->phy);
+		if (retval != -EPROBE_DEFER && retval != -ENODEV)
+			dev_err(&pdev->dev, "failed to get the phy\n");
+		else
+			return -EPROBE_DEFER;
+		goto err_put_hcd;
+	}
+
+	hcd->rsrc_start = r->start;
+	hcd->rsrc_len = resource_size(r);
+
+	hcd->irq = platform_get_irq(pdev, 0);
+	if (!hcd->irq) {
+		dev_err(&pdev->dev, "Cannot get irq.");
+		retval = -ENODEV;
+		goto err_put_hcd;
+	}
+
+	retval = phy_init(hcd->phy);
+	if (retval)
+		goto err_put_hcd;
+
+	clk_prepare(ehci_mv->clk);
+	clk_enable(ehci_mv->clk);
+
+	retval = usb_add_hcd(hcd, hcd->irq, IRQF_SHARED);
+	if (retval) {
+		dev_err(&pdev->dev,
+			"failed to add hcd with err %d\n", retval);
+		goto err_disable_clk;
+	}
+
+	retval = mv_ehci_enable(ehci_mv);
+	if (retval) {
+		dev_err(&pdev->dev,
+			"EHCI: private init failed with err %d\n", retval);
+		goto err_disable_clk;
+	}
+
+	device_wakeup_enable(hcd->self.controller);
+
+	return 0;
+
+err_disable_clk:
+	clk_disable(ehci_mv->clk);
+	clk_unprepare(ehci_mv->clk);
+	phy_exit(hcd->phy);
+err_put_hcd:
+	usb_put_hcd(hcd);
+	return retval;
+}
+
+static int mv_ehci_remove(struct platform_device *pdev)
+{
+	struct ehci_hcd_mv *ehci_mv = platform_get_drvdata(pdev);
+	struct usb_hcd *hcd = ehci_mv->hcd;
+
+	phy_power_off(hcd->phy);
+	phy_exit(hcd->phy);
+	clk_disable(ehci_mv->clk);
+	clk_unprepare(ehci_mv->clk);
+
+	usb_remove_hcd(hcd);
+	usb_put_hcd(hcd);
+
+	return 0;
+}
+
+static const struct of_device_id mv_ehci_dt_match[] = {
+	{.compatible = "marvell,pxa1928-ehci"},
+	{},
+};
+MODULE_DEVICE_TABLE(of, mv_ehci_dt_match);
+
+static void mv_ehci_shutdown(struct platform_device *pdev)
+{
+	struct ehci_hcd_mv *ehci_mv = platform_get_drvdata(pdev);
+	struct usb_hcd *hcd = ehci_mv->hcd;
+
+	if (!hcd->rh_registered)
+		return;
+
+	if (hcd->driver->shutdown)
+		hcd->driver->shutdown(hcd);
+}
+
+static const struct ehci_driver_overrides ehci_mv_overrides __initconst = {
+	.extra_priv_size =	sizeof(struct ehci_hcd_mv),
+};
+
+static struct platform_driver ehci_mv_driver = {
+	.probe = mv_ehci_probe,
+	.remove = mv_ehci_remove,
+	.shutdown = mv_ehci_shutdown,
+	.driver = {
+		   .name = "mv-ehci-of",
+		   .of_match_table = of_match_ptr(mv_ehci_dt_match),
+		   },
+};
+
+static int __init ehci_mv_init(void)
+{
+	if (usb_disabled())
+		return -ENODEV;
+
+	ehci_init_driver(&ehci_mv_hc_driver, &ehci_mv_overrides);
+	return platform_driver_register(&ehci_mv_driver);
+}
+module_init(ehci_mv_init);
+
+static void __exit ehci_mv_cleanup(void)
+{
+	platform_driver_unregister(&ehci_mv_driver);
+}
+module_exit(ehci_mv_cleanup);
+
+MODULE_AUTHOR("Rob Herring <robh@xxxxxxxxxx>");
+MODULE_LICENSE("GPL v2");
-- 
2.1.0

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/