[PATCH v8 3/5] pwm: kona: Fix incorrect config, disable, and polarity procedures

[Jonathan Richardson]

The config procedure didn't follow the spec which periodically resulted
in failing to enable the output signal. This happened one in ten or
twenty attempts. Following the spec and adding a 400ns delay in the
appropriate locations resolves this problem.

The disable and polarity procedures now also follow the spec. The old
procedures would result in no change in signal when called.

Reviewed-by: Arun Ramamurthy <arunrama@xxxxxxxxxxxx>
Reviewed-by: Scott Branden <sbranden@xxxxxxxxxxxx>
Tested-by: Scott Branden <sbranden@xxxxxxxxxxxx>
Signed-off-by: Jonathan Richardson <jonathar@xxxxxxxxxxxx>
---
 drivers/pwm/pwm-bcm-kona.c |   47 +++++++++++++++++++++++++++++++++++---------
 1 file changed, 38 insertions(+), 9 deletions(-)

diff --git a/drivers/pwm/pwm-bcm-kona.c b/drivers/pwm/pwm-bcm-kona.c
index 32b3ec6..c87621f 100644
--- a/drivers/pwm/pwm-bcm-kona.c
+++ b/drivers/pwm/pwm-bcm-kona.c
@@ -76,19 +76,36 @@ static inline struct kona_pwmc *to_kona_pwmc(struct pwm_chip *_chip)
 	return container_of(_chip, struct kona_pwmc, chip);
 }
 
-static void kona_pwmc_apply_settings(struct kona_pwmc *kp, unsigned int chan)
+/*
+ * Clear trigger bit but set smooth bit to maintain old output.
+ */
+static void kona_pwmc_prepare_for_settings(struct kona_pwmc *kp,
+	unsigned int chan)
 {
 	unsigned int value = readl(kp->base + PWM_CONTROL_OFFSET);
 
-	/* Clear trigger bit but set smooth bit to maintain old output */
 	value |= 1 << PWM_CONTROL_SMOOTH_SHIFT(chan);
 	value &= ~(1 << PWM_CONTROL_TRIGGER_SHIFT(chan));
 	writel(value, kp->base + PWM_CONTROL_OFFSET);
 
+	/*
+	 * There must be a min 400ns delay between clearing enable and setting
+	 * it. Failing to do this may result in no PWM signal.
+	 */
+	ndelay(400);
+}
+
+static void kona_pwmc_apply_settings(struct kona_pwmc *kp, unsigned int chan)
+{
+	unsigned int value = readl(kp->base + PWM_CONTROL_OFFSET);
+
 	/* Set trigger bit and clear smooth bit to apply new settings */
 	value &= ~(1 << PWM_CONTROL_SMOOTH_SHIFT(chan));
 	value |= 1 << PWM_CONTROL_TRIGGER_SHIFT(chan);
 	writel(value, kp->base + PWM_CONTROL_OFFSET);
+
+	/* PWMOUT_ENABLE must be held high for at least 400 ns. */
+	ndelay(400);
 }
 
 static int kona_pwmc_config(struct pwm_chip *chip, struct pwm_device *pwm,
@@ -133,8 +150,14 @@ static int kona_pwmc_config(struct pwm_chip *chip, struct pwm_device *pwm,
 			return -EINVAL;
 	}
 
-	/* If the PWM channel is enabled, write the settings to the HW */
+	/*
+	 * Don't apply settings if disabled. The period and duty cycle are
+	 * always calculated above to ensure the new values are
+	 * validated immediately instead of on enable.
+	 */
 	if (test_bit(PWMF_ENABLED, &pwm->flags)) {
+		kona_pwmc_prepare_for_settings(kp, chan);
+
 		value = readl(kp->base + PRESCALE_OFFSET);
 		value &= ~PRESCALE_MASK(chan);
 		value |= prescale << PRESCALE_SHIFT(chan);
@@ -164,6 +187,8 @@ static int kona_pwmc_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm,
 		return ret;
 	}
 
+	kona_pwmc_prepare_for_settings(kp, chan);
+
 	value = readl(kp->base + PWM_CONTROL_OFFSET);
 
 	if (polarity == PWM_POLARITY_NORMAL)
@@ -175,9 +200,6 @@ static int kona_pwmc_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm,
 
 	kona_pwmc_apply_settings(kp, chan);
 
-	/* Wait for waveform to settle before gating off the clock */
-	ndelay(400);
-
 	clk_disable_unprepare(kp->clk);
 
 	return 0;
@@ -207,13 +229,20 @@ static void kona_pwmc_disable(struct pwm_chip *chip, struct pwm_device *pwm)
 {
 	struct kona_pwmc *kp = to_kona_pwmc(chip);
 	unsigned int chan = pwm->hwpwm;
+	unsigned int value;
+
+	kona_pwmc_prepare_for_settings(kp, chan);
 
 	/* Simulate a disable by configuring for zero duty */
 	writel(0, kp->base + DUTY_CYCLE_HIGH_OFFSET(chan));
-	kona_pwmc_apply_settings(kp, chan);
+	writel(0, kp->base + PERIOD_COUNT_OFFSET(chan));
 
-	/* Wait for waveform to settle before gating off the clock */
-	ndelay(400);
+	/* Set prescale to 0 for this channel */
+	value = readl(kp->base + PRESCALE_OFFSET);
+	value &= ~PRESCALE_MASK(chan);
+	writel(value, kp->base + PRESCALE_OFFSET);
+
+	kona_pwmc_apply_settings(kp, chan);
 
 	clk_disable_unprepare(kp->clk);
 }
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/