[PATCH 4/7] soc: brcmstb: add PM suspend/resume support (S2/S3/S5)
From: Brian Norris
Date: Thu Jun 18 2015 - 20:13:39 EST
Support S2, S3, and S5 through /sys/power/state ("standby" and "mem")
and the poweroff code paths. See comments in pm.c for a few more details
about these system suspend modes.
Signed-off-by: Brian Norris <computersforpeace@xxxxxxxxx>
---
drivers/soc/brcmstb/Kconfig | 10 +
drivers/soc/brcmstb/Makefile | 2 +
drivers/soc/brcmstb/pm/Makefile | 1 +
drivers/soc/brcmstb/pm/aon_defs.h | 85 +++++++
drivers/soc/brcmstb/pm/pm.c | 512 ++++++++++++++++++++++++++++++++++++++
drivers/soc/brcmstb/pm/pm.h | 40 +++
drivers/soc/brcmstb/pm/s2.S | 73 ++++++
7 files changed, 723 insertions(+)
create mode 100644 drivers/soc/brcmstb/pm/Makefile
create mode 100644 drivers/soc/brcmstb/pm/aon_defs.h
create mode 100644 drivers/soc/brcmstb/pm/pm.c
create mode 100644 drivers/soc/brcmstb/pm/pm.h
create mode 100644 drivers/soc/brcmstb/pm/s2.S
diff --git a/drivers/soc/brcmstb/Kconfig b/drivers/soc/brcmstb/Kconfig
index 39cab3bd544d..5025dacce6f0 100644
--- a/drivers/soc/brcmstb/Kconfig
+++ b/drivers/soc/brcmstb/Kconfig
@@ -7,3 +7,13 @@ menuconfig SOC_BRCMSTB
can be enabled individually within this menu.
If unsure, say N.
+
+if SOC_BRCMSTB
+
+config BRCMSTB_PM
+ bool "Support suspend/resume for STB platforms"
+ default y
+ depends on PM
+ depends on ARM && ARCH_BRCMSTB
+
+endif # SOC_BRCMSTB
diff --git a/drivers/soc/brcmstb/Makefile b/drivers/soc/brcmstb/Makefile
index 183280e39f80..677e3fa0d042 100644
--- a/drivers/soc/brcmstb/Makefile
+++ b/drivers/soc/brcmstb/Makefile
@@ -1 +1,3 @@
+obj-$(CONFIG_BRCMSTB_PM) += pm/
+
obj-y += common.o
diff --git a/drivers/soc/brcmstb/pm/Makefile b/drivers/soc/brcmstb/pm/Makefile
new file mode 100644
index 000000000000..71a1ff4c368b
--- /dev/null
+++ b/drivers/soc/brcmstb/pm/Makefile
@@ -0,0 +1 @@
+obj-y += pm.o s2.o
diff --git a/drivers/soc/brcmstb/pm/aon_defs.h b/drivers/soc/brcmstb/pm/aon_defs.h
new file mode 100644
index 000000000000..2b660fa788e4
--- /dev/null
+++ b/drivers/soc/brcmstb/pm/aon_defs.h
@@ -0,0 +1,85 @@
+/*
+ * Always ON (AON) register interface between bootloader and Linux
+ *
+ * Copyright  2014-2015 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __BRCMSTB_AON_DEFS_H__
+#define __BRCMSTB_AON_DEFS_H__
+
+#include <linux/compiler.h>
+
+/* Magic number in upper 16-bits */
+#define BRCMSTB_S3_MAGIC_MASK 0xffff0000
+#define BRCMSTB_S3_MAGIC_SHORT 0x5AFE0000
+
+enum {
+ /* Restore random key for AES memory verification (off = fixed key) */
+ S3_FLAG_LOAD_RANDKEY = (1 << 0),
+
+ /* Scratch buffer page table is present */
+ S3_FLAG_SCRATCH_BUFFER_TABLE = (1 << 1),
+
+ /* Skip all memory verification */
+ S3_FLAG_NO_MEM_VERIFY = (1 << 2),
+};
+
+#define BRCMSTB_HASH_LEN (128 / 8) /* 128-bit hash */
+
+#define AON_REG_MAGIC_FLAGS 0x00
+#define AON_REG_CONTROL_LOW 0x04
+#define AON_REG_CONTROL_HIGH 0x08
+#define AON_REG_S3_HASH 0x0c /* hash of S3 params */
+#define AON_REG_CONTROL_HASH_LEN 0x1c
+
+#define BRCMSTB_S3_MAGIC 0x5AFEB007
+#define BOOTLOADER_SCRATCH_SIZE 64
+#define IMAGE_DESCRIPTORS_BUFSIZE (2 * 1024)
+
+/*
+ * Bootloader utilizes a custom parameter block left in DRAM for handling S3
+ * warm resume
+ */
+struct brcmstb_s3_params {
+ /* scratch memory for bootloader */
+ uint8_t scratch[BOOTLOADER_SCRATCH_SIZE];
+
+ uint32_t magic; /* BRCMSTB_S3_MAGIC */
+ uint64_t reentry; /* PA */
+
+ /* descriptors */
+ uint32_t hash[BRCMSTB_HASH_LEN / 4];
+
+ /*
+ * If 0, then ignore this parameter (there is only one set of
+ * descriptors)
+ *
+ * If non-0, then a second set of descriptors is stored at:
+ *
+ * descriptors + desc_offset_2
+ *
+ * The MAC result of both descriptors is XOR'd and stored in @hash
+ */
+ uint32_t desc_offset_2;
+
+ /*
+ * (Physical) address of a brcmstb_bootloader_scratch_table, for
+ * providing a large DRAM buffer to the bootloader
+ */
+ uint64_t buffer_table;
+
+ uint32_t spare[70];
+
+ uint8_t descriptors[IMAGE_DESCRIPTORS_BUFSIZE];
+} __packed;
+
+#endif /* __BRCMSTB_AON_DEFS_H__ */
diff --git a/drivers/soc/brcmstb/pm/pm.c b/drivers/soc/brcmstb/pm/pm.c
new file mode 100644
index 000000000000..04f0528d5322
--- /dev/null
+++ b/drivers/soc/brcmstb/pm/pm.c
@@ -0,0 +1,512 @@
+/*
+ * ARM-specific support for Broadcom STB S2/S3/S5 power management
+ *
+ * S2: clock gate CPUs and as many peripherals as possible
+ * S3: power off all of the chip except the Always ON (AON) island; keep DDR is
+ * self-refresh
+ * S5: (a.k.a. S3 cold boot) much like S3, except DDR is powered down, so we
+ * treat this mode like a soft power-off, with wakeup allowed from AON
+ *
+ * Copyright  2014-2015 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#define pr_fmt(fmt) "brcmstb-pm: " fmt
+
+#include <linux/kernel.h>
+#include <linux/printk.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/suspend.h>
+#include <linux/err.h>
+#include <linux/delay.h>
+#include <linux/compiler.h>
+#include <linux/pm.h>
+#include <linux/bitops.h>
+#include <linux/dma-mapping.h>
+#include <linux/sizes.h>
+#include <linux/slab.h>
+#include <linux/kconfig.h>
+#include <asm/fncpy.h>
+#include <asm/suspend.h>
+#include <asm/setup.h>
+
+#include <soc/brcmstb/common.h>
+
+#include "pm.h"
+#include "aon_defs.h"
+
+#define BRCMSTB_DDR_PHY_PLL_STATUS 0x04
+
+#define SHIMPHY_DDR_PAD_CNTRL 0x8c
+#define SHIMPHY_PAD_PLL_SEQUENCE BIT(8)
+#define SHIMPHY_PAD_GATE_PLL_S3 BIT(9)
+
+#define MAX_NUM_MEMC 3
+
+/* Capped for performance reasons */
+#define MAX_HASH_SIZE SZ_256M
+/* Max per bank, to keep some fairness */
+#define MAX_HASH_SIZE_BANK SZ_64M
+
+struct brcmstb_memc {
+ void __iomem *ddr_phy_base;
+ void __iomem *ddr_shimphy_base;
+};
+
+struct brcmstb_pm_control {
+ void __iomem *aon_ctrl_base;
+ void __iomem *aon_sram;
+ struct brcmstb_memc memcs[MAX_NUM_MEMC];
+
+ void __iomem *boot_sram;
+ size_t boot_sram_len;
+
+ bool support_warm_boot;
+ int num_memc;
+
+ struct brcmstb_s3_params *s3_params;
+ dma_addr_t s3_params_pa;
+};
+
+enum bsp_initiate_command {
+ BSP_CLOCK_STOP = 0x00,
+ BSP_GEN_RANDOM_KEY = 0x4A,
+ BSP_RESTORE_RANDOM_KEY = 0x55,
+ BSP_GEN_FIXED_KEY = 0x63,
+};
+
+#define PM_INITIATE 0x01
+#define PM_INITIATE_SUCCESS 0x00
+#define PM_INITIATE_FAIL 0xfe
+
+static struct brcmstb_pm_control ctrl;
+
+extern const unsigned long brcmstb_pm_do_s2_sz;
+extern asmlinkage int brcmstb_pm_do_s2(void __iomem *aon_ctrl_base,
+ void __iomem *ddr_phy_pll_status);
+
+static int (*brcmstb_pm_do_s2_sram)(void __iomem *aon_ctrl_base,
+ void __iomem *ddr_phy_pll_status);
+
+static int brcmstb_init_sram(struct device_node *dn)
+{
+ void __iomem *sram;
+ struct resource res;
+ int ret;
+
+ ret = of_address_to_resource(dn, 0, &res);
+ if (ret)
+ return ret;
+
+ /* Cached, executable remapping of SRAM */
+ sram = __arm_ioremap_exec(res.start, resource_size(&res), true);
+ if (!sram)
+ return -ENOMEM;
+
+ ctrl.boot_sram = sram;
+ ctrl.boot_sram_len = resource_size(&res);
+
+ return 0;
+}
+
+/*
+ * Latch into the BRCM SRAM compatible property here to be more specific than
+ * the standard "mmio-sram". Could be supported with genalloc too, but that
+ * would be overkill for its current single use-case.
+ */
+static const struct of_device_id sram_dt_ids[] = {
+ { .compatible = "brcm,boot-sram" },
+ {}
+};
+
+static int do_bsp_initiate_command(enum bsp_initiate_command cmd)
+{
+ void __iomem *base = ctrl.aon_ctrl_base;
+ int ret;
+ int timeo = 1000 * 1000; /* 1 second */
+
+ __raw_writel(0, base + AON_CTRL_PM_INITIATE);
+ (void)__raw_readl(base + AON_CTRL_PM_INITIATE);
+
+ /* Go! */
+ __raw_writel((cmd << 1) | PM_INITIATE, base + AON_CTRL_PM_INITIATE);
+
+ for (;;) {
+ ret = __raw_readl(base + AON_CTRL_PM_INITIATE);
+ if (!(ret & PM_INITIATE))
+ break;
+ if (timeo <= 0) {
+ pr_err("error: timeout waiting for BSP (%x)\n", ret);
+ break;
+ }
+ timeo -= 50;
+ udelay(50);
+ }
+
+ return (ret & 0xff) != PM_INITIATE_SUCCESS;
+}
+
+static int brcmstb_pm_handshake(void)
+{
+ void __iomem *base = ctrl.aon_ctrl_base;
+ u32 tmp;
+ int ret;
+
+ /* BSP power handshake, v1 */
+ tmp = __raw_readl(base + AON_CTRL_HOST_MISC_CMDS);
+ tmp &= ~1UL;
+ __raw_writel(tmp, base + AON_CTRL_HOST_MISC_CMDS);
+ (void)__raw_readl(base + AON_CTRL_HOST_MISC_CMDS);
+
+ ret = do_bsp_initiate_command(BSP_CLOCK_STOP);
+ if (ret)
+ pr_err("BSP handshake failed\n");
+
+ /*
+ * HACK: BSP may have internal race on the CLOCK_STOP command.
+ * Avoid touching the BSP for a few milliseconds.
+ */
+ mdelay(3);
+
+ return ret;
+}
+
+/*
+ * Run a Power Management State Machine (PMSM) shutdown command and put the CPU
+ * into a low-power mode
+ */
+static void brcmstb_do_pmsm_power_down(unsigned long base_cmd)
+{
+ void __iomem *base = ctrl.aon_ctrl_base;
+
+ /* pm_start_pwrdn transition 0->1 */
+ __raw_writel(base_cmd, base + AON_CTRL_PM_CTRL);
+ (void)__raw_readl(base + AON_CTRL_PM_CTRL);
+
+ __raw_writel(base_cmd | PM_PWR_DOWN, base + AON_CTRL_PM_CTRL);
+ (void)__raw_readl(base + AON_CTRL_PM_CTRL);
+
+ wfi();
+}
+
+/* Support S5 cold boot out of "poweroff" */
+static void brcmstb_pm_poweroff(void)
+{
+ brcmstb_pm_handshake();
+
+ /* Clear magic S3 warm-boot value */
+ __raw_writel(0, ctrl.aon_sram + AON_REG_MAGIC_FLAGS);
+ (void)__raw_readl(ctrl.aon_sram + AON_REG_MAGIC_FLAGS);
+
+ /* Skip wait-for-interrupt signal; just use a countdown */
+ __raw_writel(0x10, ctrl.aon_ctrl_base + AON_CTRL_PM_CPU_WAIT_COUNT);
+ (void)__raw_readl(ctrl.aon_ctrl_base + AON_CTRL_PM_CPU_WAIT_COUNT);
+
+ brcmstb_do_pmsm_power_down(PM_COLD_CONFIG);
+}
+
+static void *brcmstb_pm_copy_to_sram(void *fn, size_t len)
+{
+ unsigned int size = ALIGN(len, FNCPY_ALIGN);
+
+ if (ctrl.boot_sram_len < size) {
+ pr_err("standby code will not fit in SRAM\n");
+ return NULL;
+ }
+
+ return fncpy(ctrl.boot_sram, fn, size);
+}
+
+/*
+ * S2 suspend/resume picks up where we left off, so we must execute carefully
+ * from SRAM, in order to allow DDR to come back up safely before we continue.
+ */
+static int brcmstb_pm_s2(void)
+{
+ brcmstb_pm_do_s2_sram = brcmstb_pm_copy_to_sram(&brcmstb_pm_do_s2,
+ brcmstb_pm_do_s2_sz);
+ if (!brcmstb_pm_do_s2_sram)
+ return -EINVAL;
+
+ return brcmstb_pm_do_s2_sram(ctrl.aon_ctrl_base,
+ ctrl.memcs[0].ddr_phy_base +
+ BRCMSTB_DDR_PHY_PLL_STATUS);
+}
+
+static int brcmstb_pm_s3_finish(void)
+{
+ struct brcmstb_s3_params *params = ctrl.s3_params;
+ phys_addr_t params_pa = ctrl.s3_params_pa;
+ phys_addr_t reentry = virt_to_phys(&cpu_resume);
+ u32 flags = S3_FLAG_NO_MEM_VERIFY;
+ int i;
+
+ /* Clear parameter structure */
+ memset(params, 0, sizeof(*params));
+
+ params->magic = BRCMSTB_S3_MAGIC;
+ params->reentry = reentry;
+
+ flush_cache_all();
+
+ flags |= BRCMSTB_S3_MAGIC_SHORT;
+
+ __raw_writel(flags, ctrl.aon_sram + AON_REG_MAGIC_FLAGS);
+ __raw_writel(lower_32_bits(params_pa),
+ ctrl.aon_sram + AON_REG_CONTROL_LOW);
+ __raw_writel(upper_32_bits(params_pa),
+ ctrl.aon_sram + AON_REG_CONTROL_HIGH);
+
+ /* gate PLL | S3 */
+ for (i = 0; i < ctrl.num_memc; i++) {
+ u32 tmp;
+ tmp = __raw_readl(ctrl.memcs[i].ddr_shimphy_base +
+ SHIMPHY_DDR_PAD_CNTRL);
+ tmp |= SHIMPHY_PAD_GATE_PLL_S3 | SHIMPHY_PAD_PLL_SEQUENCE;
+ __raw_writel(tmp, ctrl.memcs[i].ddr_shimphy_base +
+ SHIMPHY_DDR_PAD_CNTRL);
+ }
+
+ brcmstb_do_pmsm_power_down(PM_WARM_CONFIG);
+
+ /* Must have been interrupted from wfi()? */
+ return -EINTR;
+}
+
+/*
+ * S3 mode resume to the bootloader before jumping back to Linux, so we can be
+ * a little less careful about running from DRAM.
+ */
+static int brcmstb_pm_do_s3(unsigned long sp)
+{
+ int ret;
+
+ /* should not return */
+ ret = brcmstb_pm_s3_finish();
+
+ pr_err("Could not enter S3\n");
+
+ return ret;
+}
+
+static int brcmstb_pm_s3(void)
+{
+ void __iomem *sp = ctrl.boot_sram + ctrl.boot_sram_len - 8;
+
+ return cpu_suspend((unsigned long)sp, brcmstb_pm_do_s3);
+}
+
+static int brcmstb_pm_standby(bool deep_standby)
+{
+ int ret;
+
+ if (brcmstb_pm_handshake())
+ return -EIO;
+
+ if (deep_standby)
+ ret = brcmstb_pm_s3();
+ else
+ ret = brcmstb_pm_s2();
+ if (ret)
+ pr_err("%s: standby failed\n", __func__);
+
+ return ret;
+}
+
+static int brcmstb_pm_enter(suspend_state_t state)
+{
+ int ret = -EINVAL;
+
+ switch (state) {
+ case PM_SUSPEND_STANDBY:
+ ret = brcmstb_pm_standby(false);
+ break;
+ case PM_SUSPEND_MEM:
+ ret = brcmstb_pm_standby(true);
+ break;
+ }
+
+ return ret;
+}
+
+static int brcmstb_pm_valid(suspend_state_t state)
+{
+ switch (state) {
+ case PM_SUSPEND_STANDBY:
+ return true;
+ case PM_SUSPEND_MEM:
+ return ctrl.support_warm_boot;
+ default:
+ return false;
+ }
+}
+
+static const struct platform_suspend_ops brcmstb_pm_ops = {
+ .enter = brcmstb_pm_enter,
+ .valid = brcmstb_pm_valid,
+};
+
+static const struct of_device_id aon_ctrl_dt_ids[] = {
+ { .compatible = "brcm,brcmstb-aon-ctrl" },
+ {}
+};
+
+struct ddr_phy_ofdata {
+ bool supports_warm_boot;
+};
+
+static struct ddr_phy_ofdata ddr_phy_225_1 = { .supports_warm_boot = false, };
+static struct ddr_phy_ofdata ddr_phy_240_1 = { .supports_warm_boot = true, };
+
+static const struct of_device_id ddr_phy_dt_ids[] = {
+ {
+ .compatible = "brcm,brcmstb-ddr-phy-v225.1",
+ .data = &ddr_phy_225_1,
+ },
+ {
+ .compatible = "brcm,brcmstb-ddr-phy-v240.1",
+ .data = &ddr_phy_240_1,
+ },
+ {
+ /* Same as v240.1, for the registers we care about */
+ .compatible = "brcm,brcmstb-ddr-phy-v240.2",
+ .data = &ddr_phy_240_1,
+ },
+ {}
+};
+
+static const struct of_device_id ddr_shimphy_dt_ids[] = {
+ { .compatible = "brcm,brcmstb-ddr-shimphy-v1.0" },
+ {}
+};
+
+static inline void __iomem *brcmstb_ioremap_node(struct device_node *dn,
+ int index)
+{
+ return of_io_request_and_map(dn, index, dn->full_name);
+}
+
+static void __iomem *brcmstb_ioremap_match(const struct of_device_id *matches,
+ int index, const void **ofdata)
+{
+ struct device_node *dn;
+ const struct of_device_id *match;
+
+ dn = of_find_matching_node_and_match(NULL, matches, &match);
+ if (!dn)
+ return ERR_PTR(-EINVAL);
+
+ if (ofdata)
+ *ofdata = match->data;
+
+ return brcmstb_ioremap_node(dn, index);
+}
+
+static int brcmstb_pm_init(void)
+{
+ struct device_node *dn;
+ void __iomem *base;
+ int ret, i;
+ const struct ddr_phy_ofdata *ddr_phy_data;
+
+ if (!soc_is_brcmstb())
+ return 0;
+
+ /* AON ctrl registers */
+ base = brcmstb_ioremap_match(aon_ctrl_dt_ids, 0, NULL);
+ if (IS_ERR(base)) {
+ pr_err("error mapping AON_CTRL\n");
+ return PTR_ERR(base);
+ }
+ ctrl.aon_ctrl_base = base;
+
+ /* AON SRAM registers */
+ base = brcmstb_ioremap_match(aon_ctrl_dt_ids, 1, NULL);
+ if (IS_ERR(base)) {
+ /* Assume standard offset */
+ ctrl.aon_sram = ctrl.aon_ctrl_base +
+ AON_CTRL_SYSTEM_DATA_RAM_OFS;
+ } else {
+ ctrl.aon_sram = base;
+ }
+
+ /* DDR PHY registers */
+ base = brcmstb_ioremap_match(ddr_phy_dt_ids, 0,
+ (const void **)&ddr_phy_data);
+ if (IS_ERR(base)) {
+ pr_err("error mapping DDR PHY\n");
+ return PTR_ERR(base);
+ }
+ ctrl.support_warm_boot = ddr_phy_data->supports_warm_boot;
+ /* Only need DDR PHY 0 for now? */
+ ctrl.memcs[0].ddr_phy_base = base;
+
+ /* DDR SHIM-PHY registers */
+ for_each_matching_node(dn, ddr_shimphy_dt_ids) {
+ i = ctrl.num_memc;
+ if (i >= MAX_NUM_MEMC) {
+ pr_warn("too many MEMCs (max %d)\n", MAX_NUM_MEMC);
+ break;
+ }
+ base = brcmstb_ioremap_node(dn, 0);
+ if (IS_ERR(base)) {
+ if (!ctrl.support_warm_boot)
+ break;
+
+ pr_err("error mapping DDR SHIMPHY %d\n", i);
+ return PTR_ERR(base);
+ }
+ ctrl.memcs[i].ddr_shimphy_base = base;
+ ctrl.num_memc++;
+ }
+
+ dn = of_find_matching_node(NULL, sram_dt_ids);
+ if (!dn) {
+ pr_err("SRAM not found\n");
+ return -EINVAL;
+ }
+
+ ret = brcmstb_init_sram(dn);
+ if (ret) {
+ pr_err("error setting up SRAM for PM\n");
+ return ret;
+ }
+
+ ctrl.s3_params = kmalloc(sizeof(*ctrl.s3_params), GFP_KERNEL);
+ if (!ctrl.s3_params)
+ return -ENOMEM;
+ ctrl.s3_params_pa = dma_map_single(NULL, ctrl.s3_params,
+ sizeof(*ctrl.s3_params),
+ DMA_TO_DEVICE);
+ if (dma_mapping_error(NULL, ctrl.s3_params_pa)) {
+ pr_err("error mapping DMA memory\n");
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ pm_power_off = brcmstb_pm_poweroff;
+ suspend_set_ops(&brcmstb_pm_ops);
+ return 0;
+
+out:
+ kfree(ctrl.s3_params);
+
+ pr_warn("PM: initialization failed with code %d\n", ret);
+
+ return ret;
+}
+
+arch_initcall(brcmstb_pm_init);
diff --git a/drivers/soc/brcmstb/pm/pm.h b/drivers/soc/brcmstb/pm/pm.h
new file mode 100644
index 000000000000..fadab6dc424a
--- /dev/null
+++ b/drivers/soc/brcmstb/pm/pm.h
@@ -0,0 +1,40 @@
+/*
+ * Definitions for Broadcom STB power management / Always ON (AON) block
+ *
+ * Copyright  2014 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __BRCMSTB_PM_H__
+#define __BRCMSTB_PM_H__
+
+#define AON_CTRL_RESET_CTRL 0x00
+#define AON_CTRL_PM_CTRL 0x04
+#define AON_CTRL_PM_STATUS 0x08
+#define AON_CTRL_PM_CPU_WAIT_COUNT 0x10
+#define AON_CTRL_PM_INITIATE 0x88
+#define AON_CTRL_HOST_MISC_CMDS 0x8c
+#define AON_CTRL_SYSTEM_DATA_RAM_OFS 0x200
+
+/* PM_CTRL bitfield */
+#define PM_FAST_PWRDOWN (1 << 6)
+#define PM_WARM_BOOT (1 << 5)
+#define PM_DEEP_STANDBY (1 << 4)
+#define PM_CPU_PWR (1 << 3)
+#define PM_USE_CPU_RDY (1 << 2)
+#define PM_PLL_PWRDOWN (1 << 1)
+#define PM_PWR_DOWN (1 << 0)
+
+#define PM_S2_COMMAND (PM_PLL_PWRDOWN | PM_USE_CPU_RDY | PM_PWR_DOWN)
+#define PM_COLD_CONFIG (PM_PLL_PWRDOWN | PM_DEEP_STANDBY)
+#define PM_WARM_CONFIG (PM_COLD_CONFIG | PM_USE_CPU_RDY | PM_WARM_BOOT)
+
+#endif /* __BRCMSTB_PM_H__ */
diff --git a/drivers/soc/brcmstb/pm/s2.S b/drivers/soc/brcmstb/pm/s2.S
new file mode 100644
index 000000000000..704c4ecb6f6f
--- /dev/null
+++ b/drivers/soc/brcmstb/pm/s2.S
@@ -0,0 +1,73 @@
+/*
+ * Copyright  2014 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+#include "pm.h"
+
+ .text
+ .align 3
+
+#define AON_CTRL_REG r10
+#define DDR_PHY_STATUS_REG r11
+
+/*
+ * r0: AON_CTRL base address
+ * r1: DDRY PHY PLL status register address
+ */
+ENTRY(brcmstb_pm_do_s2)
+ stmfd sp!, {r4-r11, lr}
+ mov AON_CTRL_REG, r0
+ mov DDR_PHY_STATUS_REG, r1
+
+ /* Flush memory transactions */
+ dsb
+
+ /* power down request */
+ ldr r0, =PM_S2_COMMAND
+ ldr r1, =0
+ str r1, [AON_CTRL_REG, #AON_CTRL_PM_CTRL]
+ ldr r1, [AON_CTRL_REG, #AON_CTRL_PM_CTRL]
+ str r0, [AON_CTRL_REG, #AON_CTRL_PM_CTRL]
+ ldr r0, [AON_CTRL_REG, #AON_CTRL_PM_CTRL]
+
+ /* Wait for interrupt */
+ wfi
+ nop
+
+ /* Bring MEMC back up */
+1: ldr r0, [DDR_PHY_STATUS_REG]
+ ands r0, #1
+ beq 1b
+
+ /* Power-up handshake */
+ ldr r0, =1
+ str r0, [AON_CTRL_REG, #AON_CTRL_HOST_MISC_CMDS]
+ ldr r0, [AON_CTRL_REG, #AON_CTRL_HOST_MISC_CMDS]
+
+ ldr r0, =0
+ str r0, [AON_CTRL_REG, #AON_CTRL_PM_CTRL]
+ ldr r0, [AON_CTRL_REG, #AON_CTRL_PM_CTRL]
+
+ /* Return to caller */
+ ldr r0, =0
+ ldmfd sp!, {r4-r11, pc}
+
+ ENDPROC(brcmstb_pm_do_s2)
+
+ /* Place literal pool here */
+ .ltorg
+
+ENTRY(brcmstb_pm_do_s2_sz)
+ .word . - brcmstb_pm_do_s2
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/