Re: [PATCH V2 2/2] mfd: 88pm88x: initialize 88pm886/88pm880 base support

From: Yi Zhang
Date: Fri Jun 26 2015 - 08:49:52 EST

Next message: Sudeep Holla: "Re: [PATCH] clockevents: return error from tick_broadcast_oneshot_control if !GENERIC_CLOCKEVENTS_BROADCAST"
Previous message: Preeti U Murthy: "Re: [PATCH] clockevents: return error from tick_broadcast_oneshot_control if !GENERIC_CLOCKEVENTS_BROADCAST"
In reply to: Lee Jones: "Re: [PATCH V2 2/2] mfd: 88pm88x: initialize 88pm886/88pm880 base support"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Thu, Jun 25, 2015 at 09:32:48AM +0100, Lee Jones wrote:
> On Fri, 12 Jun 2015, Yi Zhang wrote:
>
> > 88pm886 and 88pm880 are combo PMIC chip, which integrates
> > regulator, onkey, rtc, gpadc, charger, fuelgauge function;
> >
> > this patch add the basic support for them, adding related resource, such as
> > interrupt, preparing for the client-device driver
> >
> > Signed-off-by: Yi Zhang <yizhang@xxxxxxxxxxx>
> > ---
> > drivers/mfd/88pm880-table.c | 173 ++++++++++++
> > drivers/mfd/88pm886-table.c | 173 ++++++++++++
> > drivers/mfd/88pm88x-core.c | 584 ++++++++++++++++++++++++++++++++++++++++
> > drivers/mfd/88pm88x-i2c.c | 167 ++++++++++++
> > drivers/mfd/88pm88x-irq.c | 171 ++++++++++++
> > drivers/mfd/88pm88x.h | 51 ++++
>
Hi, Lee:

Thanks very much for your patience on such a long patch, it is my
fault, I will modify according to your precious comments and split
them in the next version, thanks very much;

> I'm initially concerned that you aren't (re)using _any_ of the 88pm*
> files already in the subsystem.

sorry for confusing you, this patch is for the 88pm886/88pm880, a new
series PMIC which is very different from the previous chips(88pm8*) in
register mapping and function;
after investigation, we tried to add this patch.
>
> > drivers/mfd/Kconfig | 12 +
> > drivers/mfd/Makefile | 3 +
> > include/linux/mfd/88pm880-reg.h | 98 +++++++
> > include/linux/mfd/88pm880.h | 59 ++++
> > include/linux/mfd/88pm886-reg.h | 59 ++++
> > include/linux/mfd/88pm886.h | 55 ++++
> > include/linux/mfd/88pm88x-reg.h | 118 ++++++++
> > include/linux/mfd/88pm88x.h | 202 ++++++++++++++
> > 14 files changed, 1925 insertions(+)
>
> Sending 2k line patches doesn't make reviewing a particularly pleasant
> experience. Please divide it up into a properly separated set. If
> you feel as though the set can't be split up, then you're probably
> coding it wrongly.

thanks, I will modify;
>
> > create mode 100644 drivers/mfd/88pm880-table.c
> > create mode 100644 drivers/mfd/88pm886-table.c
> > create mode 100644 drivers/mfd/88pm88x-core.c
> > create mode 100644 drivers/mfd/88pm88x-i2c.c
> > create mode 100644 drivers/mfd/88pm88x-irq.c
> > create mode 100644 drivers/mfd/88pm88x.h
> > create mode 100644 include/linux/mfd/88pm880-reg.h
> > create mode 100644 include/linux/mfd/88pm880.h
> > create mode 100644 include/linux/mfd/88pm886-reg.h
> > create mode 100644 include/linux/mfd/88pm886.h
> > create mode 100644 include/linux/mfd/88pm88x-reg.h
> > create mode 100644 include/linux/mfd/88pm88x.h
> >
> > diff --git a/drivers/mfd/88pm880-table.c b/drivers/mfd/88pm880-table.c
> > new file mode 100644
> > index 0000000..28ca860
> > --- /dev/null
> > +++ b/drivers/mfd/88pm880-table.c
> > @@ -0,0 +1,173 @@
> > +/*
> > + * Marvell 88PM880 specific setting
> > + *
> > + * Copyright (C) 2015 Marvell International Ltd.
> > + * Yi Zhang <yizhang@xxxxxxxxxxx>
>
> Tea Maker, Project Manger, CEO, Janitor?
>
> Or "Author: "

My fault, thanks;
>
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#include <linux/kernel.h>
> > +#include <linux/device.h>
> > +#include <linux/mfd/88pm88x.h>
> > +#include <linux/mfd/88pm880.h>
> > +#include <linux/mfd/88pm880-reg.h>
> > +#include <linux/mfd/88pm88x-reg.h>
> > +
> > +#include "88pm88x.h"
> > +
> > +#define PM880_BUCK_NAME "88pm880-buck"
> > +#define PM880_LDO_NAME "88pm880-ldo"
> > +
> > +const struct regmap_config pm880_base_i2c_regmap = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + .max_register = 0xfe,
> > +};
> > +
> > +const struct regmap_config pm880_power_i2c_regmap = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + .max_register = 0xfe,
> > +};
> > +
> > +const struct regmap_config pm880_gpadc_i2c_regmap = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + .max_register = 0xfe,
> > +};
> > +
> > +const struct regmap_config pm880_battery_i2c_regmap = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + .max_register = 0xfe,
> > +};
> > +
> > +const struct regmap_config pm880_test_i2c_regmap = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + .max_register = 0xfe,
> > +};
> > +
> > +static const struct resource buck_resources[] = {
> > + {
> > + .name = PM880_BUCK_NAME,
>
> Tabbing.

Got it;
>
> > + },
> > +};
> > +
> > +static const struct resource ldo_resources[] = {
> > + {
> > + .name = PM880_LDO_NAME,
>
> Tabbing.

Yes;
>
> > + },
> > +};
> > +
> > +const struct mfd_cell pm880_cell_devs[] = {
> > + CELL_DEV(PM880_BUCK_NAME, buck_resources, "marvell,88pm880-buck1a", 0),
> > + CELL_DEV(PM880_BUCK_NAME, buck_resources, "marvell,88pm880-buck2", 1),
> > + CELL_DEV(PM880_BUCK_NAME, buck_resources, "marvell,88pm880-buck3", 2),
> > + CELL_DEV(PM880_BUCK_NAME, buck_resources, "marvell,88pm880-buck4", 3),
> > + CELL_DEV(PM880_BUCK_NAME, buck_resources, "marvell,88pm880-buck5", 4),
> > + CELL_DEV(PM880_BUCK_NAME, buck_resources, "marvell,88pm880-buck6", 5),
> > + CELL_DEV(PM880_BUCK_NAME, buck_resources, "marvell,88pm880-buck7", 6),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo1", 7),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo2", 8),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo3", 9),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo4", 10),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo5", 11),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo6", 12),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo7", 13),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo8", 14),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo9", 15),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo10", 16),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo11", 17),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo12", 18),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo13", 19),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo14", 20),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo15", 21),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo16", 22),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo17", 23),
> > + CELL_DEV(PM880_LDO_NAME, ldo_resources, "marvell,88pm880-ldo18", 24),
> > +};
>
> You don't want an MFD for each regulator. See the DT documentation
> for regulators.

OK, I will change
>
> > +struct pmic_cell_info pm880_cell_info = {
> > + .cells = pm880_cell_devs,
> > + .cell_nr = ARRAY_SIZE(pm880_cell_devs),
> > +};
>
> No need for this, please remove it.
Yes, you are right, if I change to use one MFD for all of the
regulators
>
> > +static const struct reg_default pm880_base_patch[] = {
> > + {PM88X_WDOG, 0x1}, /* disable watchdog */
>
> Pad it out like you did the others "0x01".
OK;
>
> > + {PM88X_AON_CTRL2, 0x2a}, /* output 32kHZ from XO */
>
> kHz

Thanks very much for pointing it out; got it;
>
> > + {PM88X_BK_OSC_CTRL1, 0x0f}, /* OSC_FREERUN = 1, to lock FLL */
>
> Don't put bit names in comments -- you should define them instead.

OK
>
> > + {PM88X_LOWPOWER2, 0x20}, /* XO_LJ = 1, enable low jitter for 32kHZ */
>
> Remove the bit name -- second part is fine.
Yes, you are right;
>
> > + /* enable LPM for internal reference group in sleep */
>
> I see you're not a fan of using capital letter to start a sentence?
..Yes, I just feel capital letter means "see me, I am important.."
OK, I will change to use it to start a sentence
>
> > + {PM88X_LOWPOWER4, 0xc0},
>
> No comment?
I will add it;
>
> > + {PM88X_BK_OSC_CTRL3, 0xc0}, /* set the duty cycle of charger DC/DC to max */
> > +};
>
> This would be easier to read if you lined it up:
>
> {PM88X_WDOG, 0x01}, /* disable watchdog */
> {PM88X_AON_CTRL2, 0x2a}, /* output 32kHZ from XO */
> {PM88X_BK_OSC_CTRL1, 0x0f}, /* OSC_FREERUN = 1, to lock FLL */
> {PM88X_LOWPOWER2, 0x20}, /* XO_LJ = 1, enable low jitter for 32kHZ */
> /* enable LPM for internal reference group in sleep */
> {PM88X_LOWPOWER4, 0xc0},
> {PM88X_BK_OSC_CTRL3, 0xc0}, /* set the duty cycle of charger DC/DC to max */
>
> ... don't you think?
>
> I also think the values should be defined. If you disagree, at the
> _very least_ please sharpen up the comments.

I will modify them, agree with you, macro is better
>
> > +static const struct reg_default pm880_power_patch[] = {
> > +};
>
> What's the point of this?

I just leave it here to get ready for the next patch, I got your
point, I should add it when I really use it.
thanks;
>
> > +static const struct reg_default pm880_gpadc_patch[] = {
> > + {PM88X_GPADC_CONFIG6, 0x03}, /* enable non-stop mode */
> > +};
>
> I personally prefer spaces after the first and before the second curly
> bracket.

Got it;
>
> > +static const struct reg_default pm880_battery_patch[] = {
> > + {PM88X_CHGBK_CONFIG6, 0xe1},
> > +};
>
> As above.
Yes;
>
> > +static const struct reg_default pm880_test_patch[] = {
> > +};
>
> Why do you have an empty struct const?
As for the above, I will remove it in this patch
>
> > +/* 88pm880 chip itself related */
>
> I have no idea what this means?
Sorry for confusing you, I mean the following setting tries to cover
the change related to chip itself, for the board specific requirement,
it should not be here;
I will modify this comments, thanks for pointing this out;
>
> > +int pm880_apply_patch(struct pm88x_chip *chip)
> > +{
> > + int ret, size;
> > +
> > + if (!chip || !chip->base_regmap || !chip->power_regmap ||
> > + !chip->gpadc_regmap || !chip->battery_regmap ||
> > + !chip->test_regmap)
> > + return -EINVAL;
>
> You already checked for this in pm88x_post_init_chip().

OK, I will remove;
>
> > + size = ARRAY_SIZE(pm880_base_patch);
> > + if (size == 0)
> > + goto power;
> > + ret = regmap_register_patch(chip->base_regmap, pm880_base_patch, size);
> > + if (ret < 0)
>
> I assume any non-zero return value is bad. If so, please change all
> of these too "if (ret)".

Yes, you are right, I will change
>
> > + return ret;
> > +
> > +power:
> > + size = ARRAY_SIZE(pm880_power_patch);
> > + if (size == 0)
> > + goto gpadc;
> > + ret = regmap_register_patch(chip->power_regmap, pm880_power_patch, size);
> > + if (ret < 0)
> > + return ret;
> > +
> > +gpadc:
> > + size = ARRAY_SIZE(pm880_gpadc_patch);
> > + if (size == 0)
> > + goto battery;
> > + ret = regmap_register_patch(chip->gpadc_regmap, pm880_gpadc_patch, size);
> > + if (ret < 0)
> > + return ret;
>
> '\n'
Yes;
>
> > +battery:
> > + size = ARRAY_SIZE(pm880_battery_patch);
> > + if (size == 0)
> > + goto test;
> > + ret = regmap_register_patch(chip->battery_regmap, pm880_battery_patch, size);
> > + if (ret < 0)
> > + return ret;
> > +
> > +test:
> > + size = ARRAY_SIZE(pm880_test_patch);
> > + if (size == 0)
> > + goto out;
> > + ret = regmap_register_patch(chip->test_regmap, pm880_test_patch, size);
> > + if (ret < 0)
> > + return ret;
>
> '\n'

Yes;
>
> > +out:
> > + return 0;
> > +}
> > +EXPORT_SYMBOL_GPL(pm880_apply_patch);
> > diff --git a/drivers/mfd/88pm886-table.c b/drivers/mfd/88pm886-table.c
> > new file mode 100644
> > index 0000000..897ee82
> > --- /dev/null
> > +++ b/drivers/mfd/88pm886-table.c
> > @@ -0,0 +1,173 @@
> > +/*
> > + * Marvell 88PM886 specific setting
> > + *
> > + * Copyright (C) 2015 Marvell International Ltd.
> > + * Yi Zhang <yizhang@xxxxxxxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#include <linux/kernel.h>
> > +#include <linux/device.h>
> > +#include <linux/mfd/88pm88x.h>
> > +#include <linux/mfd/88pm886.h>
> > +#include <linux/mfd/88pm886-reg.h>
> > +#include <linux/mfd/88pm88x-reg.h>
> > +
> > +#include "88pm88x.h"
> > +
> > +#define PM886_BUCK_NAME "88pm886-buck"
> > +#define PM886_LDO_NAME "88pm886-ldo"
> > +
> > +const struct regmap_config pm886_base_i2c_regmap = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + .max_register = 0xfe,
> > +};
> > +
> > +const struct regmap_config pm886_power_i2c_regmap = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + .max_register = 0xfe,
> > +};
> > +
> > +const struct regmap_config pm886_gpadc_i2c_regmap = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + .max_register = 0xfe,
> > +};
> > +
> > +const struct regmap_config pm886_battery_i2c_regmap = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + .max_register = 0xfe,
> > +};
> > +
> > +const struct regmap_config pm886_test_i2c_regmap = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + .max_register = 0xfe,
> > +};
> > +
> > +static const struct resource buck_resources[] = {
> > + {
> > + .name = PM886_BUCK_NAME,
> > + },
> > +};
> > +
> > +static const struct resource ldo_resources[] = {
> > + {
> > + .name = PM886_LDO_NAME,
> > + },
> > +};
> > +
> > +const struct mfd_cell pm886_cell_devs[] = {
> > + CELL_DEV(PM886_BUCK_NAME, buck_resources, "marvell,88pm886-buck1", 0),
> > + CELL_DEV(PM886_BUCK_NAME, buck_resources, "marvell,88pm886-buck2", 1),
> > + CELL_DEV(PM886_BUCK_NAME, buck_resources, "marvell,88pm886-buck3", 2),
> > + CELL_DEV(PM886_BUCK_NAME, buck_resources, "marvell,88pm886-buck4", 3),
> > + CELL_DEV(PM886_BUCK_NAME, buck_resources, "marvell,88pm886-buck5", 4),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo1", 5),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo2", 6),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo3", 7),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo4", 8),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo5", 9),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo6", 10),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo7", 11),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo8", 12),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo9", 13),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo10", 14),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo11", 15),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo12", 16),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo13", 17),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo14", 18),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo15", 19),
> > + CELL_DEV(PM886_LDO_NAME, ldo_resources, "marvell,88pm886-ldo16", 20),
> > +};
>
> You don't want an MFD for each regulator. See the DT documentation
> for regulators.

Yes;
>
> > +struct pmic_cell_info pm886_cell_info = {
> > + .cells = pm886_cell_devs,
> > + .cell_nr = ARRAY_SIZE(pm886_cell_devs),
> > +};
>
> No need for this, please remove it.
Yes;
>
> > +static const struct reg_default pm886_base_patch[] = {
> > + {PM88X_WDOG, 0x1}, /* disable watchdog */
> > + {PM88X_GPIO_CTRL1, 0x40}, /* gpio1: dvc , gpio0: input */
> > + {PM88X_GPIO_CTRL2, 0x00}, /* , gpio2: input */
> > + {PM88X_GPIO_CTRL3, 0x44}, /* dvc2 , dvc1 */
> > + {PM88X_GPIO_CTRL4, 0x00}, /* gpio5v_1:input, gpio5v_2: input*/
> > + {PM88X_AON_CTRL2, 0x2a}, /* output 32kHZ from XO */
> > + {PM88X_BK_OSC_CTRL1, 0x0f}, /* OSC_FREERUN = 1, to lock FLL */
> > + {PM88X_LOWPOWER2, 0x20}, /* XO_LJ = 1, enable low jitter for 32kHZ */
> > + /* enable LPM for internal reference group in sleep */
> > + {PM88X_LOWPOWER4, 0xc0},
> > + {PM88X_BK_OSC_CTRL3, 0xc0}, /* set the duty cycle of charger DC/DC to max */
> > +};
> > +
> > +static const struct reg_default pm886_power_patch[] = {
> > +};
> > +
> > +static const struct reg_default pm886_gpadc_patch[] = {
> > + {PM88X_GPADC_CONFIG6, 0x03}, /* enable non-stop mode */
> > +};
> > +
> > +static const struct reg_default pm886_battery_patch[] = {
> > + {PM88X_CHGBK_CONFIG6, 0xe1},
> > +};
> > +
> > +static const struct reg_default pm886_test_patch[] = {
> > +};
> > +
> > +/* 88pm886 chip itself related */
> > +int pm886_apply_patch(struct pm88x_chip *chip)
> > +{
> > + int ret, size;
> > +
> > + if (!chip || !chip->base_regmap || !chip->power_regmap ||
> > + !chip->gpadc_regmap || !chip->battery_regmap ||
> > + !chip->test_regmap)
> > + return -EINVAL;
>
> You already checked for this in pm88x_post_init_chip().
Yes;
>
> > + size = ARRAY_SIZE(pm886_base_patch);
> > + if (size == 0)
> > + goto power;
> > + ret = regmap_register_patch(chip->base_regmap, pm886_base_patch, size);
> > + if (ret < 0)
> > + return ret;
> > +
> > +power:
> > + size = ARRAY_SIZE(pm886_power_patch);
> > + if (size == 0)
> > + goto gpadc;
> > + ret = regmap_register_patch(chip->power_regmap, pm886_power_patch, size);
> > + if (ret < 0)
> > + return ret;
> > +
> > +gpadc:
> > + size = ARRAY_SIZE(pm886_gpadc_patch);
> > + if (size == 0)
> > + goto battery;
> > + ret = regmap_register_patch(chip->gpadc_regmap, pm886_gpadc_patch, size);
> > + if (ret < 0)
> > + return ret;
> > +battery:
> > + size = ARRAY_SIZE(pm886_battery_patch);
> > + if (size == 0)
> > + goto test;
> > + ret = regmap_register_patch(chip->battery_regmap, pm886_battery_patch, size);
> > + if (ret < 0)
> > + return ret;
> > +
> > +test:
> > + size = ARRAY_SIZE(pm886_test_patch);
> > + if (size == 0)
> > + goto out;
> > + ret = regmap_register_patch(chip->test_regmap, pm886_test_patch, size);
> > + if (ret < 0)
> > + return ret;
> > +out:
> > + return 0;
> > +}
> > +EXPORT_SYMBOL_GPL(pm886_apply_patch);
>
> A lot of this code looks identical to the previous *-table.c file and
> a bunch of it is duplicated line from line. Please amalgamate them
> and find a way to reduce the amount of lines. I can think of several
> ways this can be done.

OK, I will modify in next patchset;
>
> > diff --git a/drivers/mfd/88pm88x-core.c b/drivers/mfd/88pm88x-core.c
> > new file mode 100644
> > index 0000000..343e0a0
> > --- /dev/null
> > +++ b/drivers/mfd/88pm88x-core.c
> > @@ -0,0 +1,584 @@
> > +/*
> > + * Base driver for Marvell 88PM886/88PM880 PMIC
> > + *
> > + * Copyright (C) 2015 Marvell International Ltd.
> > + * Yi Zhang <yizhang@xxxxxxxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/err.h>
> > +#include <linux/i2c.h>
> > +#include <linux/irq.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/irqdomain.h>
> > +#include <linux/of.h>
> > +#include <linux/of_platform.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/regmap.h>
> > +#include <linux/slab.h>
> > +#include <linux/mfd/core.h>
> > +#include <linux/mfd/88pm88x.h>
> > +#include <linux/mfd/88pm886.h>
> > +#include <linux/mfd/88pm880.h>
> > +#include <linux/regulator/machine.h>
> > +
> > +#include "88pm88x.h"
> > +
> > +#define PM88X_POWER_UP_LOG (0x17)
> > +#define PM88X_POWER_DOWN_LOG1 (0xe5)
> > +#define PM88X_POWER_DOWN_LOG2 (0xe6)
> > +#define PM88X_SW_PDOWN (1 << 5)
> > +
> > +static const struct resource onkey_resources[] = {
> > + CELL_IRQ_RESOURCE(PM88X_ONKEY_NAME, PM88X_IRQ_ONKEY),
> > +};
> > +
> > +static const struct resource rtc_resources[] = {
> > + CELL_IRQ_RESOURCE(PM88X_RTC_NAME, PM88X_IRQ_RTC),
> > +};
> > +
> > +static const struct resource charger_resources[] = {
> > + CELL_IRQ_RESOURCE("88pm88x-chg-fail", PM88X_IRQ_CHG_FAIL),
> > + CELL_IRQ_RESOURCE("88pm88x-chg-done", PM88X_IRQ_CHG_DONE),
> > + CELL_IRQ_RESOURCE("88pm88x-chg-good", PM88X_IRQ_CHG_GOOD),
> > +};
> > +
> > +static const struct resource battery_resources[] = {
> > + CELL_IRQ_RESOURCE("88pm88x-bat-cc", PM88X_IRQ_CC),
> > + CELL_IRQ_RESOURCE("88pm88x-bat-volt", PM88X_IRQ_VBAT),
> > + CELL_IRQ_RESOURCE("88pm88x-bat-detect", PM88X_IRQ_BAT_DET),
> > +};
> > +
> > +static const struct resource headset_resources[] = {
> > + CELL_IRQ_RESOURCE("88pm88x-headset-det", PM88X_IRQ_HS_DET),
> > + CELL_IRQ_RESOURCE("88pm88x-mic-det", PM88X_IRQ_MIC_DET),
> > +};
> > +
> > +static const struct resource vbus_resources[] = {
> > + CELL_IRQ_RESOURCE("88pm88x-vbus-det", PM88X_IRQ_VBUS),
> > + CELL_IRQ_RESOURCE("88pm88x-gpadc0", PM88X_IRQ_GPADC0),
> > + CELL_IRQ_RESOURCE("88pm88x-gpadc1", PM88X_IRQ_GPADC1),
> > + CELL_IRQ_RESOURCE("88pm88x-gpadc2", PM88X_IRQ_GPADC2),
> > + CELL_IRQ_RESOURCE("88pm88x-gpadc3", PM88X_IRQ_GPADC3),
> > + CELL_IRQ_RESOURCE("88pm88x-otg-fail", PM88X_IRQ_OTG_FAIL),
> > +};
> > +
> > +static const struct resource leds_resources[] = {
> > + CELL_IRQ_RESOURCE("88pm88x-cfd-fail", PM88X_IRQ_CFD_FAIL),
> > +};
> > +
> > +static const struct resource dvc_resources[] = {
> > + {
> > + .name = PM88X_DVC_NAME,
> > + },
> > +};
> > +
> > +static const struct resource rgb_resources[] = {
> > + {
> > + .name = PM88X_RGB_NAME,
> > + },
> > +};
> > +
> > +static const struct resource gpadc_resources[] = {
> > + {
> > + .name = PM88X_GPADC_NAME,
> > + },
> > +};
>
> Tabbing for all of the above.

Sure, thanks;
>
> In fact, for one line struct entries, I would prefer:
>
> { .name = PM88X_GPADC_NAME },
>
> > +static const struct mfd_cell common_cell_devs[] = {
> > + CELL_DEV(PM88X_RTC_NAME, rtc_resources, "marvell,88pm88x-rtc", -1),
> > + CELL_DEV(PM88X_ONKEY_NAME, onkey_resources, "marvell,88pm88x-onkey", -1),
> > + CELL_DEV(PM88X_CHARGER_NAME, charger_resources, "marvell,88pm88x-charger", -1),
> > + CELL_DEV(PM88X_BATTERY_NAME, battery_resources, "marvell,88pm88x-battery", -1),
> > + CELL_DEV(PM88X_HEADSET_NAME, headset_resources, "marvell,88pm88x-headset", -1),
> > + CELL_DEV(PM88X_VBUS_NAME, vbus_resources, "marvell,88pm88x-vbus", -1),
> > + CELL_DEV(PM88X_CFD_NAME, leds_resources, "marvell,88pm88x-leds", PM88X_FLASH_LED),
> > + CELL_DEV(PM88X_CFD_NAME, leds_resources, "marvell,88pm88x-leds", PM88X_TORCH_LED),
> > + CELL_DEV(PM88X_DVC_NAME, dvc_resources, "marvell,88pm88x-dvc", -1),
> > + CELL_DEV(PM88X_RGB_NAME, rgb_resources, "marvell,88pm88x-rgb0", PM88X_RGB_LED0),
> > + CELL_DEV(PM88X_RGB_NAME, rgb_resources, "marvell,88pm88x-rgb1", PM88X_RGB_LED1),
> > + CELL_DEV(PM88X_RGB_NAME, rgb_resources, "marvell,88pm88x-rgb2", PM88X_RGB_LED2),
>
> This isn't how it works. You should have one LED entry here, then let
> the LED driver take care of all this stuff.

OK, I will modify it;
>
> > + CELL_DEV(PM88X_GPADC_NAME, gpadc_resources, "marvell,88pm88x-gpadc", -1),
> > +};
>
>
> > +const struct of_device_id pm88x_of_match[] = {
> > + { .compatible = "marvell,88pm886", .data = (void *)PM886 },
> > + { .compatible = "marvell,88pm880", .data = (void *)PM880 },
> > + {},
> > +};
> > +
> > +struct pm88x_chip *pm88x_init_chip(struct i2c_client *client)
>
> Why is this in a seperate file to the one it's called from? I
> suggest you move it into the *-i2c.c file.

OK, I'll do it; yes, it can be there;
>
> > +{
> > + struct pm88x_chip *chip;
> > +
> > + chip = devm_kzalloc(&client->dev, sizeof(struct pm88x_chip), GFP_KERNEL);
>
> Calling this 'chip' is confusing, as it has different connotations
> depending on the subsystem.
>
> ddata (for device data) or priv for (private) is more common.

So thank you; I prefer ddata;
>
> > + if (!chip)
> > + return ERR_PTR(-ENOMEM);
> > +
> > + chip->client = client;
> > + chip->irq = client->irq;
> > + chip->dev = &client->dev;
>
> Why are you storing 'client' AND 'dev'? Do you use 'client' directly?
> If not, ditch it. If you do, then just store 'client' and extract
> 'client->dev' when you require it.

OK, I am in the second case, I will modify it;
>
> > + chip->ldo_page_addr = client->addr + 1;
> > + chip->power_page_addr = client->addr + 1;
> > + chip->gpadc_page_addr = client->addr + 2;
> > + chip->battery_page_addr = client->addr + 3;
> > + chip->buck_page_addr = client->addr + 4;
> > + chip->test_page_addr = client->addr + 7;
>
> I have no idea what's going on here, but it's almost certainly not
> correct. Instead of separating these out per device have a base
> address and create DEFINES for each of them.

it is because this PMIC has several i2c address, each has different
function, the offset vesus the client->addr is fixed, the client->addr
is 0x30 from device tree, then the gpadc_page_addr is 0x32, that is
why I use client->addr + 2;

you mean the DEFINES are better?

>
> > + dev_set_drvdata(chip->dev, chip);
> > + i2c_set_clientdata(chip->client, chip);
>
> Why do you have both of these?

I think i2c_set_clientdata() is enough for my case, thanks;
>
> > + device_init_wakeup(&client->dev, 1);
> > +
> > + return chip;
>
> You're wearing a belt and 2 pairs of braces here. You just stored
> 'chip' into the device's private data area, why are you returning it
> too?

my fault, I will change
>
> > +}
> > +
> > +int pm88x_parse_dt(struct device_node *np, struct pm88x_chip *chip)
> > +{
> > + if (!chip)
> > + return -EINVAL;
> > +
> > + chip->irq_mode =
> > + !of_property_read_bool(np, "marvell,88pm88x-irq-write-clear");
>
> A new function for just one line? Just move it into probe()

I planned to add this function in case more properties are needed,
OK, I will move to probe()
>
> > + return 0;
> > +}
> > +
> > +
>
> Superfluous '\n'.
I will remove;
>
> > +static void parse_powerup_down_log(struct pm88x_chip *chip)
> > +{
> > + int powerup, powerdown1, powerdown2, bit;
> > + int powerup_bits, powerdown1_bits, powerdown2_bits;
> > + static const char * const powerup_name[] = {
> > + "ONKEY_WAKEUP ",
> > + "CHG_WAKEUP ",
> > + "EXTON_WAKEUP ",
> > + "SMPL_WAKEUP ",
> > + "ALARM_WAKEUP ",
> > + "FAULT_WAKEUP ",
> > + "BAT_WAKEUP ",
> > + "WLCHG_WAKEUP ",
> > + };
> > + static const char * const powerdown1_name[] = {
> > + "OVER_TEMP ",
> > + "UV_VANA5 ",
> > + "SW_PDOWN ",
> > + "FL_ALARM ",
> > + "WD ",
> > + "LONG_ONKEY",
> > + "OV_VSYS ",
> > + "RTC_RESET "
> > + };
> > + static const char * const powerdown2_name[] = {
> > + "HYB_DONE ",
> > + "UV_VBAT ",
> > + "HW_RESET2 ",
> > + "PGOOD_PDOWN",
> > + "LONKEY_RTC ",
> > + "HW_RESET1 ",
> > + };
> > +
> > + regmap_read(chip->base_regmap, PM88X_POWER_UP_LOG, &powerup);
> > + regmap_read(chip->base_regmap, PM88X_POWER_DOWN_LOG1, &powerdown1);
> > + regmap_read(chip->base_regmap, PM88X_POWER_DOWN_LOG2, &powerdown2);
> > +
> > + /*
> > + * mask reserved bits
> > + *
> > + * note: HYB_DONE and HW_RESET1 are kept,
> > + * but should not be considered as power down events
> > + */
> > + switch (chip->type) {
> > + case PM886:
> > + powerup &= 0x7f;
> > + powerdown2 &= 0x1f;
> > + powerup_bits = 7;
> > + powerdown1_bits = 8;
> > + powerdown2_bits = 5;
> > + break;
> > + case PM880:
> > + powerdown2 &= 0x3f;
> > + powerup_bits = 8;
> > + powerdown1_bits = 8;
> > + powerdown2_bits = 6;
> > + break;
> > + default:
> > + return;
> > + }
> > +
> > + /* keep globals for external usage */
> > + chip->powerup = powerup;
> > + chip->powerdown1 = powerdown1;
> > + chip->powerdown2 = powerdown2;
> > +
> > + /* power up log */
> > + dev_info(chip->dev, "powerup log 0x%x: 0x%x\n",
> > + PM88X_POWER_UP_LOG, powerup);
> > + dev_info(chip->dev, " ----------------------------\n");
> > + dev_info(chip->dev, "| name(power up) | status |\n");
> > + dev_info(chip->dev, "|-----------------|----------|\n");
> > + for (bit = 0; bit < powerup_bits; bit++)
> > + dev_info(chip->dev, "| %s | %x |\n",
> > + powerup_name[bit], (powerup >> bit) & 1);
> > + dev_info(chip->dev, " ----------------------------\n");
> > +
> > + /* power down log1 */
> > + dev_info(chip->dev, "PowerDW Log1 0x%x: 0x%x\n",
> > + PM88X_POWER_DOWN_LOG1, powerdown1);
> > + dev_info(chip->dev, " -------------------------------\n");
> > + dev_info(chip->dev, "| name(power down1) | status |\n");
> > + dev_info(chip->dev, "|--------------------|----------|\n");
> > + for (bit = 0; bit < powerdown1_bits; bit++)
> > + dev_info(chip->dev, "| %s | %x |\n",
> > + powerdown1_name[bit], (powerdown1 >> bit) & 1);
> > + dev_info(chip->dev, " -------------------------------\n");
> > +
> > + /* power down log2 */
> > + dev_info(chip->dev, "PowerDW Log2 0x%x: 0x%x\n",
> > + PM88X_POWER_DOWN_LOG2, powerdown2);
> > + dev_info(chip->dev, " -------------------------------\n");
> > + dev_info(chip->dev, "| name(power down2) | status |\n");
> > + dev_info(chip->dev, "|--------------------|----------|\n");
> > + for (bit = 0; bit < powerdown2_bits; bit++)
> > + dev_info(chip->dev, "| %s | %x |\n",
> > + powerdown2_name[bit], (powerdown2 >> bit) & 1);
> > + dev_info(chip->dev, " -------------------------------\n");
> > +
> > + /* write to clear power down log */
> > + regmap_write(chip->base_regmap, PM88X_POWER_DOWN_LOG1, 0xff);
> > + regmap_write(chip->base_regmap, PM88X_POWER_DOWN_LOG2, 0xff);
> > +}
> > +
> > +static const char *chip_stepping_to_string(unsigned int id)
> > +{
> > + switch (id) {
> > + case 0xa1:
> > + return "88pm886 A1";
> > + case 0xb1:
> > + return "88pm880 A1";
> > + default:
> > + return "Unknown";
> > + }
> > +}
> > +
> > +int pm88x_post_init_chip(struct pm88x_chip *chip)
> > +{
> > + int ret;
> > + unsigned int val;
> > +
> > + if (!chip || !chip->base_regmap || !chip->power_regmap ||
> > + !chip->gpadc_regmap || !chip->battery_regmap)
> > + return -EINVAL;
> > +
> > + /* save chip stepping */
> > + ret = regmap_read(chip->base_regmap, PM88X_ID_REG, &val);
> > + if (ret < 0) {
> > + dev_err(chip->dev, "Failed to read chip ID: %d\n", ret);
> > + return ret;
> > + }
> > + chip->chip_id = val;
> > +
> > + dev_info(chip->dev, "PM88X chip ID = 0x%x(%s)\n", val,
> > + chip_stepping_to_string(chip->chip_id));
> > +
> > + /* read before alarm wake up bit before initialize interrupt */
> > + ret = regmap_read(chip->base_regmap, PM88X_RTC_ALARM_CTRL1, &val);
> > + if (ret < 0) {
> > + dev_err(chip->dev, "Failed to read RTC register: %d\n", ret);
> > + return ret;
> > + }
> > + chip->rtc_wakeup = !!(val & PM88X_ALARM_WAKEUP);
> > +
> > + parse_powerup_down_log(chip);
> > +
> > + return 0;
> > +}
> > +
> > +int pm88x_init_pages(struct pm88x_chip *chip)
> > +{
> > + struct i2c_client *client = chip->client;
> > + const struct regmap_config *base_regmap_config;
> > + const struct regmap_config *power_regmap_config;
> > + const struct regmap_config *gpadc_regmap_config;
> > + const struct regmap_config *battery_regmap_config;
> > + const struct regmap_config *test_regmap_config;
> > + int ret = 0;
> > +
> > + if (!chip || !chip->power_page_addr ||
> > + !chip->gpadc_page_addr || !chip->battery_page_addr)
> > + return -ENODEV;
> > +
> > + chip->type = pm88x_of_get_type(&client->dev);
> > + switch (chip->type) {
> > + case PM886:
> > + base_regmap_config = &pm886_base_i2c_regmap;
> > + power_regmap_config = &pm886_power_i2c_regmap;
> > + gpadc_regmap_config = &pm886_gpadc_i2c_regmap;
> > + battery_regmap_config = &pm886_battery_i2c_regmap;
> > + test_regmap_config = &pm886_test_i2c_regmap;
> > + break;
> > + case PM880:
> > + base_regmap_config = &pm880_base_i2c_regmap;
> > + power_regmap_config = &pm880_power_i2c_regmap;
> > + gpadc_regmap_config = &pm880_gpadc_i2c_regmap;
> > + battery_regmap_config = &pm880_battery_i2c_regmap;
> > + test_regmap_config = &pm880_test_i2c_regmap;
> > + break;
> > + default:
> > + return -ENODEV;
>
> You could probably do with an error message here.
I got your point, good suggestion, thank you;
>
> > + }
> > +
> > + /* base page */
> > + chip->base_regmap = devm_regmap_init_i2c(client, base_regmap_config);
> > + if (IS_ERR(chip->base_regmap)) {
> > + dev_err(chip->dev, "Failed to init base_regmap: %d\n", ret);
> > + ret = PTR_ERR(chip->base_regmap);
> > + goto out;
> > + }
> > +
> > + /* power page */
> > + chip->power_page = i2c_new_dummy(client->adapter, chip->power_page_addr);
> > + if (!chip->power_page) {
> > + dev_err(chip->dev, "Failed to new power_page: %d\n", ret);
> > + ret = -ENODEV;
> > + goto out;
> > + }
> > + chip->power_regmap = devm_regmap_init_i2c(chip->power_page,
> > + power_regmap_config);
> > + if (IS_ERR(chip->power_regmap)) {
> > + dev_err(chip->dev, "Failed to init power_regmap: %d\n", ret);
> > + ret = PTR_ERR(chip->power_regmap);
> > + goto out;
> > + }
> > +
> > + /* gpadc page */
> > + chip->gpadc_page = i2c_new_dummy(client->adapter, chip->gpadc_page_addr);
> > + if (!chip->gpadc_page) {
> > + dev_err(chip->dev, "Failed to new gpadc_page: %d\n", ret);
> > + ret = -ENODEV;
> > + goto out;
> > + }
> > + chip->gpadc_regmap = devm_regmap_init_i2c(chip->gpadc_page,
> > + gpadc_regmap_config);
> > + if (IS_ERR(chip->gpadc_regmap)) {
> > + dev_err(chip->dev, "Failed to init gpadc_regmap: %d\n", ret);
> > + ret = PTR_ERR(chip->gpadc_regmap);
> > + goto out;
> > + }
> > +
> > + /* battery page */
> > + chip->battery_page = i2c_new_dummy(client->adapter, chip->battery_page_addr);
> > + if (!chip->battery_page) {
> > + dev_err(chip->dev, "Failed to new gpadc_page: %d\n", ret);
> > + ret = -ENODEV;
> > + goto out;
> > + }
> > + chip->battery_regmap = devm_regmap_init_i2c(chip->battery_page,
> > + battery_regmap_config);
> > + if (IS_ERR(chip->battery_regmap)) {
> > + dev_err(chip->dev, "Failed to init battery_regmap: %d\n", ret);
> > + ret = PTR_ERR(chip->battery_regmap);
> > + goto out;
> > + }
> > +
> > + /* test page */
> > + chip->test_page = i2c_new_dummy(client->adapter, chip->test_page_addr);
> > + if (!chip->test_page) {
> > + dev_err(chip->dev, "Failed to new test_page: %d\n", ret);
> > + ret = -ENODEV;
> > + goto out;
> > + }
> > + chip->test_regmap = devm_regmap_init_i2c(chip->test_page,
> > + test_regmap_config);
> > + if (IS_ERR(chip->test_regmap)) {
> > + dev_err(chip->dev, "Failed to init test_regmap: %d\n", ret);
> > + ret = PTR_ERR(chip->test_regmap);
> > + goto out;
> > + }
>
> There's a lot of duplicated code here. You can save quite a few lines
> if you thought about it I'm sure.

I will try to fix it in next patchset, thanks for your reminder;
I am ashamed about this
>
> > + chip->type = pm88x_of_get_type(&client->dev);
> > + switch (chip->type) {
> > + case PM886:
> > + /* ldo page */
> > + chip->ldo_page = chip->power_page;
> > + chip->ldo_regmap = chip->power_regmap;
> > + /* buck page */
> > + chip->buck_regmap = chip->power_regmap;
> > + break;
> > + case PM880:
> > + /* ldo page */
> > + chip->ldo_page = chip->power_page;
> > + chip->ldo_regmap = chip->power_regmap;
> > +
> > + /* buck page */
> > + chip->buck_page = i2c_new_dummy(client->adapter,
> > + chip->buck_page_addr);
> > + if (!chip->buck_page) {
> > + dev_err(chip->dev, "Failed to new buck_page: %d\n", ret);
> > + ret = -ENODEV;
> > + goto out;
> > + }
> > + chip->buck_regmap = devm_regmap_init_i2c(chip->buck_page,
> > + power_regmap_config);
> > + if (IS_ERR(chip->buck_regmap)) {
> > + dev_err(chip->dev, "Failed to init buck_regmap: %d\n", ret);
> > + ret = PTR_ERR(chip->buck_regmap);
> > + goto out;
> > + }
> > +
> > + break;
> > + default:
> > + ret = -EINVAL;
>
> Firstly, this probably won't happen, as the first switch() succeeded.
> Secondly, you are returning a different error value, why? Thirdly,
> you probably want an error message here.

for the first question, you are right, I will re-org this function to
make it clearer;
for the second question, my fault, I should write -ENODEV here;
for third, definitly an error message is right, thank you;
>
> > + break;
> > + }
> > +out:
> > + return ret;
> > +}
> > +
> > +void pm800_exit_pages(struct pm88x_chip *chip)
> > +{
> > + if (!chip)
> > + return;
> > +
> > + if (chip->ldo_page)
> > + i2c_unregister_device(chip->ldo_page);
> > + if (chip->gpadc_page)
> > + i2c_unregister_device(chip->gpadc_page);
> > + if (chip->test_page)
> > + i2c_unregister_device(chip->test_page);
>
> '\n'
Yes;
>
> > + /* no need to unregister ldo_page */
> > + switch (chip->type) {
> > + case PM886:
> > + break;
> > + case PM880:
> > + if (chip->buck_page)
> > + i2c_unregister_device(chip->buck_page);
> > + break;
> > + default:
> > + break;
> > + }
>
> No need for this big switch(). Just do:

Good, it's much cleaner than mine, thank you;
>
> if (chip->buck_page)
> i2c_unregister_device(chip->buck_page);
>
> > +}
> > +
> > +int pm88x_init_subdev(struct pm88x_chip *chip)
> > +{
> > + int ret;
>
> '\n'
OK;
>
> This will raise a Checkpatch error. Did you run this set though
> checkpatch.pl?

I am sorry to say it's my fault, I promise it will not happen again.
>
> > + if (!chip)
> > + return -EINVAL;
>
> I'm pretty sure you can't get here if !chip.

Yes, I will change
>
> > + ret = mfd_add_devices(chip->dev, 0, common_cell_devs,
>
> What does 0 mean?

I should use -1 here, though it _seems_ works..
>
> > + ARRAY_SIZE(common_cell_devs), NULL, 0,
> > + regmap_irq_get_domain(chip->irq_data));
> > + if (ret < 0)
>
> if (ret)

OK
>
> > + return ret;
> > +
> > + switch (chip->type) {
> > + case PM886:
> > + ret = mfd_add_devices(chip->dev, 0, pm886_cell_info.cells,
> > + pm886_cell_info.cell_nr, NULL, 0,
> > + regmap_irq_get_domain(chip->irq_data));
> > + break;
> > + case PM880:
> > + ret = mfd_add_devices(chip->dev, 0, pm880_cell_info.cells,
> > + pm880_cell_info.cell_nr, NULL, 0,
> > + regmap_irq_get_domain(chip->irq_data));
>
> switch() on {pm880_cell_info|pm886_cell_info.cells}.cells etc and just
> call mfd_add_devices() once.

Yes, you are right
>
> > + break;
> > + default:
> > + break;
> > + }
> > + return ret;
> > +}
> > +
> > +static int (*apply_to_chip)(struct pm88x_chip *chip);
> > +/* PMIC chip itself related */
> > +int pm88x_apply_patch(struct pm88x_chip *chip)
> > +{
> > + if (!chip || !chip->client)
> > + return -EINVAL;
> > +
> > + chip->type = pm88x_of_get_type(&chip->client->dev);
> > + switch (chip->type) {
> > + case PM886:
> > + apply_to_chip = pm886_apply_patch;
> > + break;
> > + case PM880:
> > + apply_to_chip = pm880_apply_patch;
> > + break;
> > + default:
> > + break;
> > + }
> > + if (apply_to_chip)
> > + apply_to_chip(chip);
> > + return 0;
> > +}
>
> What on earth is going on here?
>
> Why bother assigning the *fn()?

because 88pm886 and 88pm880 have different pages, the latter has one
more page, so I added two function here by assigning the *fn(), after
more thoughts, I think this is not needed, I will modify to use a
better method, thanks for your criticism
>
> > +int pm88x_stepping_fixup(struct pm88x_chip *chip)
> > +{
> > + if (!chip || !chip->client)
> > + return -EINVAL;
>
> I don't think this can happen.

I will remove;
>
> > + chip->type = pm88x_of_get_type(&chip->client->dev);
> > + switch (chip->type) {
> > + case PM886:
> > + case PM880:
> > + default:
> > + break;
> > + }
> > +
> > + return 0;
> > +}
>
> This function appears to do nothing. Why is it here?

I planed to implement in the following patchset, now I know I should
merge it into the next one;
>
> > +int pm88x_apply_board_fixup(struct pm88x_chip *chip, struct device_node *np)
> > +{
> > + /* add board design specific setting, parsed via device tree */
> > + return 0;
> > +}
>
> What's this? Another empty function.

same with above;
>
> > +long pm88x_of_get_type(struct device *dev)
> > +{
> > + const struct of_device_id *id = of_match_device(pm88x_of_match, dev);
> > +
> > + if (id)
> > + return (long)id->data;
> > + else
> > + return 0;
> > +}
>
> Just do this once, in probe and store the value in driver data. No
> need for a function to do this.

got it;
>
> > +void pm88x_dev_exit(struct pm88x_chip *chip)
> > +{
> > + mfd_remove_devices(chip->dev);
> > + pm88x_irq_exit(chip);
> > +}
> > +
> > +void pm88x_power_off(void)
> > +{
> > + pr_info("powers off the system.");
> > + /* TODO: implement later */
>
> Why can't you implement this now?

OK, I will add in the next version
>
> > + for (;;)
> > + cpu_relax();
>
> What's the point of this?

I just would like to busy loop at the end of the power_off callback;
>
> > +}
> > +
> > +int pm88x_reboot_notifier_callback(struct notifier_block *this,
> > + unsigned long code, void *unused)
> > +{
> > + struct pm88x_chip *chip =
> > + container_of(this, struct pm88x_chip, reboot_notifier);
> > +
> > + switch (code) {
> > + case SYS_HALT:
> > + case SYS_POWER_OFF:
> > + dev_info(chip->dev, "system is down.\n");
> > + break;
> > + case SYS_RESTART:
> > + default:
> > + dev_info(chip->dev, "system will reboot.\n");
> > + break;
> > + }
> > +
> > + return 0;
> > +}
>
> This function is pointless.

my intention is to record what has happened to the system, I will
double consider of it; thanks;
>
> > diff --git a/drivers/mfd/88pm88x-i2c.c b/drivers/mfd/88pm88x-i2c.c
> > new file mode 100644
> > index 0000000..36842ed
> > --- /dev/null
> > +++ b/drivers/mfd/88pm88x-i2c.c
> > @@ -0,0 +1,167 @@
> > +/*
> > + * 88pm88x-i2c.c -- 88pm88x i2c bus interface
> > + *
> > + * Copyright (C) 2015 Marvell International Ltd.
> > + * Yi Zhang <yizhang@xxxxxxxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#include <linux/err.h>
> > +#include <linux/i2c.h>
> > +#include <linux/module.h>
> > +#include <linux/pm_runtime.h>
> > +#include <linux/regmap.h>
> > +#include <linux/regulator/consumer.h>
> > +#include <linux/slab.h>
> > +#include <linux/of.h>
> > +#include <linux/mfd/core.h>
> > +#include <linux/mfd/88pm886.h>
> > +#include <linux/mfd/88pm880.h>
> > +#include <linux/mfd/88pm88x.h>
> > +
> > +static int pm88x_i2c_probe(struct i2c_client *client,
> > + const struct i2c_device_id *id)
> > +{
> > + struct pm88x_chip *chip;
> > + struct device_node *node = client->dev.of_node;
> > + int ret = 0;
> > +
> > + chip = pm88x_init_chip(client);
>
> This function doesn't actually do any chip initialisation.

actually, yes, it only does some software work.. I will find a better
name in next version
>
> ... and the code should be moved into here.
>
> > + if (IS_ERR(chip)) {
> > + ret = PTR_ERR(chip);
> > + dev_err(chip->dev, "initialize 88pm88x chip fails!\n");
>
> "Failed to initialise chip"

OK, I will scan and modify all of the error log. thanks very much;
>
> > + goto err;
>
> Just return.

OK;
>
> > + }
> > +
> > + ret = pm88x_parse_dt(node, chip);
> > + if (ret < 0) {
> > + dev_err(chip->dev, "parse dt fails!\n");
>
> "Failed to parse DT"
got it;
>
> > + goto err;
>
> Just return.
>
> > + }
> > +
> > + ret = pm88x_init_pages(chip);
> > + if (ret) {
> > + dev_err(chip->dev, "initialize 88pm88x pages fails!\n");
>
> Etc ...
got it;
>
> > + goto err;
>
> Just return.
got it;
>
> > + }
> > +
> > + ret = pm88x_post_init_chip(chip);
> > + if (ret) {
> > + dev_err(chip->dev, "post initialize 88pm88x fails!\n");
> > + goto err;
>
> Just return.
got it;
>
> > + }
> > +
> > + ret = pm88x_irq_init(chip);
> > + if (ret) {
> > + dev_err(chip->dev, "initialize 88pm88x interrupt fails!\n");
> > + goto err_init_irq;
> > + }
> > +
> > + ret = pm88x_init_subdev(chip);
> > + if (ret) {
> > + dev_err(chip->dev, "initialize 88pm88x sub-device fails\n");
> > + goto err_init_subdev;
> > + }
> > +
> > + /* patch for PMIC chip itself */
> > + ret = pm88x_apply_patch(chip);
> > + if (ret) {
> > + dev_err(chip->dev, "apply 88pm88x register patch fails\n");
> > + goto err_apply_patch;
> > + }
> > +
> > + /* fixup according PMIC stepping */
>
> This comment doesn't make any sense.

I will change, my intention is add chip stepping specific setting
>
> > + ret = pm88x_stepping_fixup(chip);
> > + if (ret) {
> > + dev_err(chip->dev, "fixup according to chip stepping\n");
> > + goto err_apply_patch;
> > + }
> > +
> > + /* patch for board configuration */
> > + ret = pm88x_apply_board_fixup(chip, node);
> > + if (ret) {
> > + dev_err(chip->dev, "apply 88pm88x register for board fails\n");
> > + goto err_apply_patch;
> > + }
> > +
> > + pm_power_off = pm88x_power_off;
> > +
> > + chip->reboot_notifier.notifier_call = pm88x_reboot_notifier_callback;
> > + register_reboot_notifier(&(chip->reboot_notifier));
> > +
> > + return 0;
> > +
> > +err_apply_patch:
> > + mfd_remove_devices(chip->dev);
> > +err_init_subdev:
> > + regmap_del_irq_chip(chip->irq, chip->irq_data);
> > +err_init_irq:
> > + pm800_exit_pages(chip);
> > +err:
>
> Remove this label.

Yes, you are right;
>
> > + return ret;
> > +}
> > +
> > +static int pm88x_i2c_remove(struct i2c_client *i2c)
> > +{
> > + struct pm88x_chip *chip = dev_get_drvdata(&i2c->dev);
> > + pm88x_dev_exit(chip);
> > + return 0;
> > +}
>
> Checkpatch will warn you about this function.

Sorry for my fault
>
> > +static const struct i2c_device_id pm88x_i2c_id[] = {
> > + { "88pm886", PM886 },
> > + { "88pm880", PM880 },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(i2c, pm88x_i2c_id);
> > +
> > +static int pm88x_i2c_suspend(struct device *dev)
> > +{
> > + return 0;
> > +}
> > +
> > +static int pm88x_i2c_resume(struct device *dev)
> > +{
> > + return 0;
> > +}
>
> Why even supply them?

I planned to implement in the next patch, now I understand I should
remove it. thanks;
>
> > +static SIMPLE_DEV_PM_OPS(pm88x_pm_ops, pm88x_i2c_suspend, pm88x_i2c_resume);
> > +
> > +static struct i2c_driver pm88x_i2c_driver = {
> > + .driver = {
> > + .name = "88pm88x",
> > + .owner = THIS_MODULE,
>
> Remove this line.
got your point
>
> > + .pm = &pm88x_pm_ops,
> > + .of_match_table = of_match_ptr(pm88x_of_match),
> > + },
> > + .probe = pm88x_i2c_probe,
> > + .remove = pm88x_i2c_remove,
> > + .id_table = pm88x_i2c_id,
> > +};
> > +
> > +static int __init pm88x_i2c_init(void)
> > +{
> > + int ret;
> > +
> > + ret = i2c_add_driver(&pm88x_i2c_driver);
> > + if (ret != 0) {
> > + pr_err("88pm88x I2C registration failed %d\n", ret);
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +subsys_initcall(pm88x_i2c_init);
> > +
> > +static void __exit pm88x_i2c_exit(void)
> > +{
> > + i2c_del_driver(&pm88x_i2c_driver);
> > +}
> > +module_exit(pm88x_i2c_exit);
>
> I think you want to remove all of this and replace with
> module_i2c_driver().

Yes, I should use module_i2c_driver();
>
> > +MODULE_DESCRIPTION("88pm88x I2C bus interface");
> > +MODULE_AUTHOR("Yi Zhang<yizhang@xxxxxxxxxxx>");
>
> Missing a space.
Yes
>
> > +MODULE_LICENSE("GPL v2");
> > diff --git a/drivers/mfd/88pm88x-irq.c b/drivers/mfd/88pm88x-irq.c
> > new file mode 100644
> > index 0000000..0126df0
> > --- /dev/null
> > +++ b/drivers/mfd/88pm88x-irq.c
> > @@ -0,0 +1,171 @@
> > +/*
> > + * 88pm886 interrupt support
> > + *
> > + * Copyright (C) 2015 Marvell International Ltd.
> > + * Yi Zhang <yizhang@xxxxxxxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#include <linux/delay.h>
> > +#include <linux/gpio.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/irq.h>
> > +#include <linux/irqdomain.h>
> > +#include <linux/pm_runtime.h>
> > +#include <linux/regmap.h>
> > +#include <linux/regulator/consumer.h>
> > +#include <linux/slab.h>
> > +#include <linux/mfd/88pm88x.h>
> > +#include <linux/mfd/88pm886.h>
> > +#include <linux/mfd/88pm880.h>
> > +
> > +/* interrupt status registers */
> > +#define PM88X_INT_STATUS1 (0x05)
> > +
> > +#define PM88X_INT_ENA_1 (0x0a)
> > +#define PM88X_ONKEY_INT_ENA1 (1 << 0)
> > +#define PM88X_EXTON_INT_ENA1 (1 << 1)
> > +#define PM88X_CHG_INT_ENA1 (1 << 2)
> > +#define PM88X_BAT_INT_ENA1 (1 << 3)
> > +#define PM88X_RTC_INT_ENA1 (1 << 4)
> > +#define PM88X_CLASSD_INT_ENA1 (1 << 5)
> > +#define PM88X_XO_INT_ENA1 (1 << 6)
> > +#define PM88X_GPIO_INT_ENA1 (1 << 7)
> > +
> > +#define PM88X_INT_ENA_2 (0x0b)
> > +#define PM88X_VBAT_INT_ENA2 (1 << 0)
> > +#define PM88X_RSVED1_INT_ENA2 (1 << 1)
> > +#define PM88X_VBUS_INT_ENA2 (1 << 2)
> > +#define PM88X_ITEMP_INT_ENA2 (1 << 3)
> > +#define PM88X_BUCK_PGOOD_INT_ENA2 (1 << 4)
> > +#define PM88X_LDO_PGOOD_INT_ENA2 (1 << 5)
> > +#define PM88X_RSVED6_INT_ENA2 (1 << 6)
> > +#define PM88X_RSVED7_INT_ENA2 (1 << 7)
> > +
> > +#define PM88X_INT_ENA_3 (0x0c)
> > +#define PM88X_GPADC0_INT_ENA3 (1 << 0)
> > +#define PM88X_GPADC1_INT_ENA3 (1 << 1)
> > +#define PM88X_GPADC2_INT_ENA3 (1 << 2)
> > +#define PM88X_GPADC3_INT_ENA3 (1 << 3)
> > +#define PM88X_MIC_INT_ENA3 (1 << 4)
> > +#define PM88X_HS_INT_ENA3 (1 << 5)
> > +#define PM88X_GND_INT_ENA3 (1 << 6)
> > +#define PM88X_RSVED7_INT_ENA3 (1 << 7)
> > +
> > +#define PM88X_INT_ENA_4 (0x0d)
> > +#define PM88X_CHG_FAIL_INT_ENA4 (1 << 0)
> > +#define PM88X_CHG_DONE_INT_ENA4 (1 << 1)
> > +#define PM88X_RSVED2_INT_ENA4 (1 << 2)
> > +#define PM88X_OTG_FAIL_INT_ENA4 (1 << 3)
> > +#define PM88X_RSVED4_INT_ENA4 (1 << 4)
> > +#define PM88X_CHG_ILIM_INT_ENA4 (1 << 5)
> > +#define PM88X_CC_INT_ENA4 (1 << 6)
> > +#define PM88X_RSVED7_INT_ENA4 (1 << 7)
> > +
> > +#define PM88X_MISC_CONFIG2 (0x15)
> > +#define PM88X_INV_INT (1 << 0)
> > +#define PM88X_INT_CLEAR (1 << 1)
> > +#define PM88X_INT_RC (0 << 1)
> > +#define PM88X_INT_WC (1 << 1)
> > +#define PM88X_INT_MASK_MODE (1 << 2)
>
> Replace all "1 <<" with BIT()
>
> > +static const struct regmap_irq pm88x_irqs[] = {
> > + /* INT0 */
> > + [PM88X_IRQ_ONKEY] = {.reg_offset = 0, .mask = PM88X_ONKEY_INT_ENA1,},
> > + [PM88X_IRQ_EXTON] = {.reg_offset = 0, .mask = PM88X_EXTON_INT_ENA1,},
> > + [PM88X_IRQ_CHG_GOOD] = {.reg_offset = 0, .mask = PM88X_CHG_INT_ENA1,},
> > + [PM88X_IRQ_BAT_DET] = {.reg_offset = 0, .mask = PM88X_BAT_INT_ENA1,},
> > + [PM88X_IRQ_RTC] = {.reg_offset = 0, .mask = PM88X_RTC_INT_ENA1,},
> > + [PM88X_IRQ_CLASSD] = { .reg_offset = 0, .mask = PM88X_CLASSD_INT_ENA1,},
> > + [PM88X_IRQ_XO] = {.reg_offset = 0, .mask = PM88X_XO_INT_ENA1,},
> > + [PM88X_IRQ_GPIO] = {.reg_offset = 0, .mask = PM88X_GPIO_INT_ENA1,},
> > +
> > + /* INT1 */
> > + [PM88X_IRQ_VBAT] = {.reg_offset = 1, .mask = PM88X_VBAT_INT_ENA2,},
> > + [PM88X_IRQ_VBUS] = {.reg_offset = 1, .mask = PM88X_VBUS_INT_ENA2,},
> > + [PM88X_IRQ_ITEMP] = {.reg_offset = 1, .mask = PM88X_ITEMP_INT_ENA2,},
> > + [PM88X_IRQ_BUCK_PGOOD] = {
> > + .reg_offset = 1,
> > + .mask = PM88X_BUCK_PGOOD_INT_ENA2,
> > + },
> > + [PM88X_IRQ_LDO_PGOOD] = {
> > + .reg_offset = 1,
> > + .mask = PM88X_LDO_PGOOD_INT_ENA2,
> > + },
> > + /* INT2 */
> > + [PM88X_IRQ_GPADC0] = {.reg_offset = 2, .mask = PM88X_GPADC0_INT_ENA3,},
> > + [PM88X_IRQ_GPADC1] = {.reg_offset = 2, .mask = PM88X_GPADC1_INT_ENA3,},
> > + [PM88X_IRQ_GPADC2] = {.reg_offset = 2, .mask = PM88X_GPADC2_INT_ENA3,},
> > + [PM88X_IRQ_GPADC3] = {.reg_offset = 2, .mask = PM88X_GPADC3_INT_ENA3,},
> > + [PM88X_IRQ_MIC_DET] = {.reg_offset = 2, .mask = PM88X_MIC_INT_ENA3,},
> > + [PM88X_IRQ_HS_DET] = {.reg_offset = 2, .mask = PM88X_HS_INT_ENA3,},
> > + [PM88X_IRQ_GND_DET] = {.reg_offset = 2, .mask = PM88X_GND_INT_ENA3,},
>
> This is not how we lay out structures (your code below is correct).
got your point.
>
> > + /* INT3 */
> > + [PM88X_IRQ_CHG_FAIL] = {
> > + .reg_offset = 3,
> > + .mask = PM88X_CHG_FAIL_INT_ENA4,
> > + },
> > + [PM88X_IRQ_CHG_DONE] = {
> > + .reg_offset = 3,
> > + .mask = PM88X_CHG_DONE_INT_ENA4,
> > + },
> > + [PM88X_IRQ_OTG_FAIL] = {
> > + .reg_offset = 3,
> > + .mask = PM88X_OTG_FAIL_INT_ENA4,
> > + },
> > + [PM88X_IRQ_CHG_ILIM] = {
> > + .reg_offset = 3,
> > + .mask = PM88X_CHG_ILIM_INT_ENA4,
> > + },
> > + [PM88X_IRQ_CC] = {.reg_offset = 3, .mask = PM88X_CC_INT_ENA4,},
> > +};
> > +
> > +struct regmap_irq_chip pm88x_irq_chip = {
> > + .name = "88pm88x",
> > + .irqs = pm88x_irqs,
> > + .num_irqs = ARRAY_SIZE(pm88x_irqs),
> > +
>
> No need for the '\n'.
thanks;
>
> > + .num_regs = 4,
> > + .status_base = PM88X_INT_STATUS1,
> > + .mask_base = PM88X_INT_ENA_1,
> > + .ack_base = PM88X_INT_STATUS1,
> > + .mask_invert = 1,
> > +};
> > +
> > +int pm88x_irq_init(struct pm88x_chip *chip)
> > +{
> > + int mask, data, ret;
> > + struct regmap *map;
>
> Not sure this variable is even needed, but if you want to keep it,
> please rename to regmap.

fine, I will use regmap
>
> > + if (!chip || !chip->base_regmap || !chip->irq) {
> > + pr_err("cannot initialize interrupt!\n");
> > + return -EINVAL;
> > + }
> > + map = chip->base_regmap;
> > +
> > + /*
> > + * irq_mode defines the way of clearing interrupt.
> > + * it's read-clear by default.
> > + */
> > + mask = PM88X_INV_INT | PM88X_INT_CLEAR | PM88X_INT_MASK_MODE;
> > + data = (chip->irq_mode) ? PM88X_INT_WC : PM88X_INT_RC;
> > + ret = regmap_update_bits(map, PM88X_MISC_CONFIG2, mask, data);
> > + if (ret < 0) {
> > + dev_err(chip->dev, "cannot set interrupt mode!\n");
> > + return ret;
> > + }
> > +
> > + ret = regmap_add_irq_chip(map, chip->irq, IRQF_ONESHOT, -1,
> > + &pm88x_irq_chip, &chip->irq_data);
> > + return ret;
> > +}
> > +
> > +int pm88x_irq_exit(struct pm88x_chip *chip)
> > +{
> > + regmap_del_irq_chip(chip->irq, chip->irq_data);
> > + return 0;
> > +}
> > diff --git a/drivers/mfd/88pm88x.h b/drivers/mfd/88pm88x.h
> > new file mode 100644
> > index 0000000..a85a486
> > --- /dev/null
> > +++ b/drivers/mfd/88pm88x.h
> > @@ -0,0 +1,51 @@
> > +#ifndef _MFD_88PM88X_H
> > +#define _MFD_88PM88X_H
> > +
> > +#include <linux/kernel.h>
> > +#include <linux/of.h>
> > +#include <linux/regmap.h>
> > +#include <linux/mfd/core.h>
> > +
> > +struct pmic_cell_info {
> > + const struct mfd_cell *cells;
> > + int cell_nr;
> > +};
>
> No need for this, please move it.
Yes;
>
> > +#define CELL_IRQ_RESOURCE(_name, _irq) { \
> > + .name = _name, \
> > + .start = _irq, .end = _irq, \
> > + .flags = IORESOURCE_IRQ, \
> > + }
>
> This already exists, DEFINE_RES*.

Thanks for reminder, yes;
>
> > +#define CELL_DEV(_name, _r, _compatible, _id) { \
> > + .name = _name, \
> > + .of_compatible = _compatible, \
> > + .num_resources = ARRAY_SIZE(_r), \
> > + .resources = _r, \
> > + .id = _id, \
> > + }
>
> This is not required.
>
> If you feel the need for an MFD Cell macro, you probably have too many
> MFD cells and you have done something wrong..

Yes, I should use one MFD to cover regulators and one MFD to cover
LEDs, I will remember this lesson; thanks;
>
> > +/* 88pm886 */
> > +extern const struct regmap_config pm886_base_i2c_regmap;
> > +extern const struct regmap_config pm886_power_i2c_regmap;
> > +extern const struct regmap_config pm886_gpadc_i2c_regmap;
> > +extern const struct regmap_config pm886_battery_i2c_regmap;
> > +extern const struct regmap_config pm886_test_i2c_regmap;
> > +
> > +extern const struct mfd_cell pm886_cell_devs[];
> > +extern struct pmic_cell_info pm886_cell_info;
> > +
> > +int pm886_apply_patch(struct pm88x_chip *chip);
> > +
> > +/* 88pm880 */
> > +extern const struct regmap_config pm880_base_i2c_regmap;
> > +extern const struct regmap_config pm880_power_i2c_regmap;
> > +extern const struct regmap_config pm880_gpadc_i2c_regmap;
> > +extern const struct regmap_config pm880_battery_i2c_regmap;
> > +extern const struct regmap_config pm880_test_i2c_regmap;
> > +
> > +extern const struct mfd_cell pm880_cell_devs[];
> > +extern struct pmic_cell_info pm880_cell_info;
> > +
> > +int pm880_apply_patch(struct pm88x_chip *chip);
>
> Place all of your code in the correct files and all these horrible
> global externs should vanish.

I will think carefully, thanks;
>
> > +#endif
> > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> > index d5ad04d..bdebca9 100644
> > --- a/drivers/mfd/Kconfig
> > +++ b/drivers/mfd/Kconfig
> > @@ -390,6 +390,18 @@ config MFD_KEMPLD
> > This driver can also be built as a module. If so, the module
> > will be called kempld-core.
> >
> > +config MFD_88PM88X
> > + tristate "Marvell 88PM886/880 PMIC"
> > + depends on I2C=y
> > + select REGMAP_I2C
> > + select MFD_CORE
> > + help
> > + This supports for Marvell 88PM88X Series Power Management IC:
> > + 88pm886 and 88pm880;
> > + This includes the I2C driver, the interrupt resource distribution
> > + and the core APIs, for individual sub-device as voltage regulators,
> > + RTC, charger, fuelgauge, etc, select under the corresponding menus.
> > +
> > config MFD_88PM800
> > tristate "Marvell 88PM800"
> > depends on I2C=y
> > diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> > index 0e5cfeb..365d1fa 100644
> > --- a/drivers/mfd/Makefile
> > +++ b/drivers/mfd/Makefile
> > @@ -6,6 +6,9 @@
> > obj-$(CONFIG_MFD_88PM860X) += 88pm860x.o
> > obj-$(CONFIG_MFD_88PM800) += 88pm800.o 88pm80x.o
> > obj-$(CONFIG_MFD_88PM805) += 88pm805.o 88pm80x.o
> > +88pm88x-objs := 88pm88x-core.o 88pm88x-i2c.o 88pm88x-irq.o 88pm886-table.o 88pm880-table.o
> > +obj-$(CONFIG_MFD_88PM88X) += 88pm88x.o
> > +
> > obj-$(CONFIG_MFD_SM501) += sm501.o
> > obj-$(CONFIG_MFD_ASIC3) += asic3.o tmio_core.o
> > obj-$(CONFIG_MFD_BCM590XX) += bcm590xx.o
> > diff --git a/include/linux/mfd/88pm880-reg.h b/include/linux/mfd/88pm880-reg.h
> > new file mode 100644
> > index 0000000..fdf2315
> > --- /dev/null
> > +++ b/include/linux/mfd/88pm880-reg.h
>
> You don't need a seperate header file for register values. Just put
> them in include/linux/mfd/88pm880.h.

OK, got it;
>
> > @@ -0,0 +1,98 @@
> > +/*
> > + * Marvell 88PM880 registers
> > + *
> > + * Copyright (C) 2014 Marvell International Ltd.
> > + * Yi Zhang <yizhang@xxxxxxxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#ifndef __LINUX_MFD_88PM880_REG_H
> > +#define __LINUX_MFD_88PM880_REG_H
> > +
> > +#define PM880_BUCK1_VOUT (0x28)
> > +
> > +#define PM880_BUCK1A_VOUT (0x28) /* voltage 0 */
> > +#define PM880_BUCK1A_1_VOUT (0x29)
> > +#define PM880_BUCK1A_2_VOUT (0x2a)
> > +#define PM880_BUCK1A_3_VOUT (0x2b)
> > +#define PM880_BUCK1A_4_VOUT (0x2c)
> > +#define PM880_BUCK1A_5_VOUT (0x2d)
> > +#define PM880_BUCK1A_6_VOUT (0x2e)
> > +#define PM880_BUCK1A_7_VOUT (0x2f)
> > +#define PM880_BUCK1A_8_VOUT (0x30)
> > +#define PM880_BUCK1A_9_VOUT (0x31)
> > +#define PM880_BUCK1A_10_VOUT (0x32)
> > +#define PM880_BUCK1A_11_VOUT (0x33)
> > +#define PM880_BUCK1A_12_VOUT (0x34)
> > +#define PM880_BUCK1A_13_VOUT (0x35)
> > +#define PM880_BUCK1A_14_VOUT (0x36)
> > +#define PM880_BUCK1A_15_VOUT (0x37)
> > +
> > +#define PM880_BUCK1B_VOUT (0x40)
> > +#define PM880_BUCK1B_1_VOUT (0x41)
> > +#define PM880_BUCK1B_2_VOUT (0x42)
> > +#define PM880_BUCK1B_3_VOUT (0x43)
> > +#define PM880_BUCK1B_4_VOUT (0x44)
> > +#define PM880_BUCK1B_5_VOUT (0x45)
> > +#define PM880_BUCK1B_6_VOUT (0x46)
> > +#define PM880_BUCK1B_7_VOUT (0x47)
> > +#define PM880_BUCK1B_8_VOUT (0x48)
> > +#define PM880_BUCK1B_9_VOUT (0x49)
> > +#define PM880_BUCK1B_10_VOUT (0x4a)
> > +#define PM880_BUCK1B_11_VOUT (0x4b)
> > +#define PM880_BUCK1B_12_VOUT (0x4c)
> > +#define PM880_BUCK1B_13_VOUT (0x4d)
> > +#define PM880_BUCK1B_14_VOUT (0x4e)
> > +#define PM880_BUCK1B_15_VOUT (0x4f)
> > +
> > +/* buck7 has dvc function */
> > +#define PM880_BUCK7_VOUT (0xb8) /* voltage 0 */
> > +#define PM880_BUCK7_1_VOUT (0xb9)
> > +#define PM880_BUCK7_2_VOUT (0xba)
> > +#define PM880_BUCK7_3_VOUT (0xbb)
> > +
> > +/*
> > + * buck sleep mode control registers:
> > + * 00-disable,
> > + * 01/10-sleep voltage,
> > + * 11-active voltage
> > + */
> > +#define PM880_BUCK1A_SLP_CTRL (0x27)
> > +#define PM880_BUCK1B_SLP_CTRL (0x3c)
> > +#define PM880_BUCK2_SLP_CTRL (0x54)
> > +#define PM880_BUCK3_SLP_CTRL (0x6c)
> > +/* TODO: there are 7 controls bit for buck4~7 */
> > +#define PM880_BUCK4_SLP_CTRL (0x84)
> > +#define PM880_BUCK5_SLP_CTRL (0x94)
> > +#define PM880_BUCK6_SLP_CTRL (0xa4)
> > +#define PM880_BUCK7_SLP_CTRL (0xb4)
> > +
> > +/*
> > + * ldo sleep mode control registers:
> > + * 00-disable,
> > + * 01/10-sleep voltage,
> > + * 11-active voltage
> > + */
> > +#define PM880_LDO1_SLP_CTRL (0x21)
> > +#define PM880_LDO2_SLP_CTRL (0x27)
> > +#define PM880_LDO3_SLP_CTRL (0x2d)
> > +#define PM880_LDO4_SLP_CTRL (0x33)
> > +#define PM880_LDO5_SLP_CTRL (0x39)
> > +#define PM880_LDO6_SLP_CTRL (0x3f)
> > +#define PM880_LDO7_SLP_CTRL (0x45)
> > +#define PM880_LDO8_SLP_CTRL (0x4b)
> > +#define PM880_LDO9_SLP_CTRL (0x51)
> > +#define PM880_LDO10_SLP_CTRL (0x57)
> > +#define PM880_LDO11_SLP_CTRL (0x5d)
> > +#define PM880_LDO12_SLP_CTRL (0x63)
> > +#define PM880_LDO13_SLP_CTRL (0x69)
> > +#define PM880_LDO14_SLP_CTRL (0x6f)
> > +#define PM880_LDO15_SLP_CTRL (0x75)
> > +#define PM880_LDO16_SLP_CTRL (0x7b)
> > +#define PM880_LDO17_SLP_CTRL (0x81)
> > +#define PM880_LDO18_SLP_CTRL (0x87)
>
> Remove the brackets around all of the above.

got it;
>
> > +#endif /*__LINUX_MFD_88PM880_REG_H */
> > diff --git a/include/linux/mfd/88pm880.h b/include/linux/mfd/88pm880.h
> > new file mode 100644
> > index 0000000..94b9e063
> > --- /dev/null
> > +++ b/include/linux/mfd/88pm880.h
> > @@ -0,0 +1,59 @@
> > +/*
> > + * Marvell 88PM880 Interface
> > + *
> > + * Copyright (C) 2015 Marvell International Ltd.
> > + * Yi Zhang <yizhang@xxxxxxxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + *
> > + * 88pm880 specific configuration: at present it's regulators and dvc part
> > + */
> > +
> > +#ifndef __LINUX_MFD_88PM880_H
> > +#define __LINUX_MFD_88PM880_H
> > +
> > +#include <linux/platform_device.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/regmap.h>
> > +#include <linux/atomic.h>
> > +#include <linux/reboot.h>
>
> Why are these required?

My fault, I should remove them;
>
> > +#include "88pm880-reg.h"
>
> <linux/mfd/88pm880.h>
>
> > +enum {
> > + PM880_ID_BUCK1A = 0,
> > + PM880_ID_BUCK2,
> > + PM880_ID_BUCK3,
> > + PM880_ID_BUCK4,
> > + PM880_ID_BUCK5,
> > + PM880_ID_BUCK6,
> > + PM880_ID_BUCK7,
> > +
> > + PM880_ID_BUCK_MAX = 7,
> > +};
> > +
> > +enum {
> > + PM880_ID_LDO1 = 0,
> > + PM880_ID_LDO2,
> > + PM880_ID_LDO3,
> > + PM880_ID_LDO4,
> > + PM880_ID_LDO5,
> > + PM880_ID_LDO6,
> > + PM880_ID_LDO7,
> > + PM880_ID_LDO8,
> > + PM880_ID_LDO9,
> > + PM880_ID_LDO10,
> > + PM880_ID_LDO11,
> > + PM880_ID_LDO12,
> > + PM880_ID_LDO13,
> > + PM880_ID_LDO14 = 13,
> > + PM880_ID_LDO15,
> > + PM880_ID_LDO16 = 15,
> > +
> > + PM880_ID_LDO17 = 16,
> > + PM880_ID_LDO18 = 17,
> > +
> > + PM880_ID_LDO_MAX = 18,
> > +};
> > +#endif /* __LINUX_MFD_88PM880_H */
> > diff --git a/include/linux/mfd/88pm886-reg.h b/include/linux/mfd/88pm886-reg.h
> > new file mode 100644
> > index 0000000..38a7ecd
> > --- /dev/null
> > +++ b/include/linux/mfd/88pm886-reg.h
> > @@ -0,0 +1,59 @@
> > +/*
> > + * Marvell 88PM886 registers
> > + *
> > + * Copyright (C) 2014 Marvell International Ltd.
> > + * Yi Zhang <yizhang@xxxxxxxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#ifndef __LINUX_MFD_88PM886_REG_H
> > +#define __LINUX_MFD_88PM886_REG_H
> > +
> > +#define PM886_BUCK1_VOUT (0xa5)
> > +#define PM886_BUCK1_1_VOUT (0xa6)
> > +#define PM886_BUCK1_2_VOUT (0xa7)
> > +#define PM886_BUCK1_3_VOUT (0xa8)
> > +#define PM886_BUCK1_4_VOUT (0x9a)
> > +#define PM886_BUCK1_5_VOUT (0x9b)
> > +#define PM886_BUCK1_6_VOUT (0x9c)
> > +#define PM886_BUCK1_7_VOUT (0x9d)
> > +
> > +/*
> > + * buck sleep mode control registers:
> > + * 00-disable,
> > + * 01/10-sleep voltage,
> > + * 11-active voltage
> > + */
> > +#define PM886_BUCK1_SLP_CTRL (0xa2)
> > +#define PM886_BUCK2_SLP_CTRL (0xb0)
> > +#define PM886_BUCK3_SLP_CTRL (0xbe)
> > +#define PM886_BUCK4_SLP_CTRL (0xcc)
> > +#define PM886_BUCK5_SLP_CTRL (0xda)
> > +
> > +/*
> > + * ldo sleep mode control registers:
> > + * 00-disable,
> > + * 01/10-sleep voltage,
> > + * 11-active voltage
> > + */
> > +#define PM886_LDO1_SLP_CTRL (0x21)
> > +#define PM886_LDO2_SLP_CTRL (0x27)
> > +#define PM886_LDO3_SLP_CTRL (0x2d)
> > +#define PM886_LDO4_SLP_CTRL (0x33)
> > +#define PM886_LDO5_SLP_CTRL (0x39)
> > +#define PM886_LDO6_SLP_CTRL (0x3f)
> > +#define PM886_LDO7_SLP_CTRL (0x45)
> > +#define PM886_LDO8_SLP_CTRL (0x4b)
> > +#define PM886_LDO9_SLP_CTRL (0x51)
> > +#define PM886_LDO10_SLP_CTRL (0x57)
> > +#define PM886_LDO11_SLP_CTRL (0x5d)
> > +#define PM886_LDO12_SLP_CTRL (0x63)
> > +#define PM886_LDO13_SLP_CTRL (0x69)
> > +#define PM886_LDO14_SLP_CTRL (0x6f)
> > +#define PM886_LDO15_SLP_CTRL (0x75)
> > +#define PM886_LDO16_SLP_CTRL (0x7b)
> > +
> > +#endif
> > diff --git a/include/linux/mfd/88pm886.h b/include/linux/mfd/88pm886.h
> > new file mode 100644
> > index 0000000..9390406
> > --- /dev/null
> > +++ b/include/linux/mfd/88pm886.h
> > @@ -0,0 +1,55 @@
> > +/*
> > + * Marvell 88PM886 Interface
> > + *
> > + * Copyright (C) 2015 Marvell International Ltd.
> > + * Yi Zhang <yizhang@xxxxxxxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + *
> > + * 88pm886 specific configuration: at present it's regulators and dvc part
> > + */
> > +
> > +#ifndef __LINUX_MFD_88PM886_H
> > +#define __LINUX_MFD_88PM886_H
> > +
> > +#include <linux/platform_device.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/regmap.h>
> > +#include <linux/atomic.h>
> > +#include <linux/reboot.h>
> > +#include "88pm886-reg.h"
> > +
> > +enum {
> > + PM886_ID_BUCK1 = 0,
> > + PM886_ID_BUCK2,
> > + PM886_ID_BUCK3,
> > + PM886_ID_BUCK4,
> > + PM886_ID_BUCK5,
> > +
> > + PM886_ID_BUCK_MAX = 5,
> > +};
> > +
> > +enum {
> > + PM886_ID_LDO1 = 0,
> > + PM886_ID_LDO2,
> > + PM886_ID_LDO3,
> > + PM886_ID_LDO4,
> > + PM886_ID_LDO5,
> > + PM886_ID_LDO6,
> > + PM886_ID_LDO7,
> > + PM886_ID_LDO8,
> > + PM886_ID_LDO9,
> > + PM886_ID_LDO10,
> > + PM886_ID_LDO11,
> > + PM886_ID_LDO12,
> > + PM886_ID_LDO13,
> > + PM886_ID_LDO14,
> > + PM886_ID_LDO15,
> > + PM886_ID_LDO16 = 15,
> > +
> > + PM886_ID_LDO_MAX = 16,
> > +};
> > +
> > +#endif /* __LINUX_MFD_88PM886_H */
> > diff --git a/include/linux/mfd/88pm88x-reg.h b/include/linux/mfd/88pm88x-reg.h
> > new file mode 100644
> > index 0000000..d767b31
> > --- /dev/null
> > +++ b/include/linux/mfd/88pm88x-reg.h
> > @@ -0,0 +1,118 @@
> > +/*
> > + * Marvell 88PM88X registers
> > + *
> > + * Copyright (C) 2014 Marvell International Ltd.
> > + * Yi Zhang <yizhang@xxxxxxxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#ifndef __LINUX_MFD_88PM88X_REG_H
> > +#define __LINUX_MFD_88PM88X_REG_H
> > +/*
> > + * This file is just used for the common registers,
> > + * which are shared by sub-clients
> > + */
> > +
> > +/*--base page:--------------------------------------------------------------*/
>
> All of the commenting above is superfluous.
>
> > +#define PM88X_ID_REG (0x0)
> > +
> > +#define PM88X_STATUS1 (0x1)
> > +#define PM88X_CHG_DET (1 << 2)
> > +#define PM88X_BAT_DET (1 << 3)
> > +
> > +#define PM88X_MISC_CONFIG1 (0x14)
> > +#define PM88X_LONKEY_RST (1 << 3)
> > +
> > +#define PM88X_WDOG (0x1d)
> > +
> > +#define PM88X_LOWPOWER2 (0x21)
> > +#define PM88X_LOWPOWER4 (0x23)
> > +
> > +/* clk control register */
> > +#define PM88X_CLK_CTRL1 (0x25)
> > +
> > +/* gpio */
> > +#define PM88X_GPIO_CTRL1 (0x30)
> > +#define PM88X_GPIO0_VAL_MSK (0x1 << 0)
> > +#define PM88X_GPIO0_MODE_MSK (0x7 << 1)
> > +#define PM88X_GPIO1_VAL_MSK (0x1 << 4)
> > +#define PM88X_GPIO1_MODE_MSK (0x7 << 5)
> > +#define PM88X_GPIO1_SET_DVC (0x2 << 5)
> > +
> > +#define PM88X_GPIO_CTRL2 (0x31)
> > +#define PM88X_GPIO2_VAL_MSK (0x1 << 0)
> > +#define PM88X_GPIO2_MODE_MSK (0x7 << 1)
> > +
> > +#define PM88X_GPIO_CTRL3 (0x32)
> > +
> > +#define PM88X_GPIO_CTRL4 (0x33)
> > +#define PM88X_GPIO5V_1_VAL_MSK (0x1 << 0)
> > +#define PM88X_GPIO5V_1_MODE_MSK (0x7 << 1)
> > +#define PM88X_GPIO5V_2_VAL_MSK (0x1 << 4)
> > +#define PM88X_GPIO5V_2_MODE_MSK (0x7 << 5)
> > +
> > +#define PM88X_BK_OSC_CTRL1 (0x50)
> > +#define PM88X_BK_OSC_CTRL3 (0x52)
> > +
> > +#define PM88X_RTC_ALARM_CTRL1 (0xd0)
> > +#define PM88X_ALARM_WAKEUP (1 << 4)
> > +#define PM88X_USE_XO (1 << 7)
> > +
> > +#define PM88X_AON_CTRL2 (0xe2)
> > +#define PM88X_AON_CTRL3 (0xe3)
> > +#define PM88X_AON_CTRL4 (0xe4)
> > +#define PM88X_AON_CTRL7 (0xe7)
> > +
> > +/* 0xea, 0xeb, 0xec, 0xed are reserved by RTC */
> > +#define PM88X_RTC_SPARE5 (0xee)
> > +#define PM88X_RTC_SPARE6 (0xef)
> > +/*-------------------------------------------------------------------------*/
> > +
> > +/*--power page:------------------------------------------------------------*/
> > +
> > +/*-------------------------------------------------------------------------*/
> > +
> > +/*--gpadc page:------------------------------------------------------------*/
>
> This type of commenting is messy and unwanted.
>
> > +#define PM88X_GPADC_CONFIG1 (0x1)
> > +
> > +#define PM88X_GPADC_CONFIG2 (0x2)
> > +#define PM88X_GPADC0_MEAS_EN (1 << 2)
> > +#define PM88X_GPADC1_MEAS_EN (1 << 3)
> > +#define PM88X_GPADC2_MEAS_EN (1 << 4)
> > +#define PM88X_GPADC3_MEAS_EN (1 << 5)
> > +
> > +#define PM88X_GPADC_CONFIG3 (0x3)
> > +
> > +#define PM88X_GPADC_CONFIG6 (0x6)
> > +#define PM88X_GPADC_CONFIG8 (0x8)
> > +
> > +#define PM88X_GPADC0_LOW_TH (0x20)
> > +#define PM88X_GPADC1_LOW_TH (0x21)
> > +#define PM88X_GPADC2_LOW_TH (0x22)
> > +#define PM88X_GPADC3_LOW_TH (0x23)
> > +
> > +#define PM88X_GPADC0_UPP_TH (0x30)
> > +#define PM88X_GPADC1_UPP_TH (0x31)
> > +#define PM88X_GPADC2_UPP_TH (0x32)
> > +#define PM88X_GPADC3_UPP_TH (0x33)
> > +
> > +#define PM88X_VBUS_MEAS1 (0x4A)
> > +#define PM88X_GPADC0_MEAS1 (0x54)
> > +#define PM88X_GPADC1_MEAS1 (0x56)
> > +#define PM88X_GPADC2_MEAS1 (0x58)
> > +#define PM88X_GPADC3_MEAS1 (0x5A)
> > +
> > +
> > +/*--charger page:------------------------------------------------------------*/
> > +#define PM88X_CHG_CONFIG1 (0x28)
> > +#define PM88X_CHGBK_CONFIG6 (0x50)
> > +/*-------------------------------------------------------------------------*/
> > +
> > +/*--test page:-------------------------------------------------------------*/
> > +
> > +/*-------------------------------------------------------------------------*/
> > +#endif
> > diff --git a/include/linux/mfd/88pm88x.h b/include/linux/mfd/88pm88x.h
> > new file mode 100644
> > index 0000000..efa2fe6
> > --- /dev/null
> > +++ b/include/linux/mfd/88pm88x.h
> > @@ -0,0 +1,202 @@
> > +/*
> > + * Marvell 88PM88X PMIC Common Interface
> > + *
> > + * Copyright (C) 2014 Marvell International Ltd.
> > + * Yi Zhang <yizhang@xxxxxxxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + *
> > + *
> > + * This file configures the common part of the 88pm88x series PMIC
> > + */
> > +
> > +#ifndef __LINUX_MFD_88PM88X_H
> > +#define __LINUX_MFD_88PM88X_H
> > +
> > +#include <linux/platform_device.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/regmap.h>
> > +#include <linux/atomic.h>
> > +#include <linux/reboot.h>
> > +#include "88pm88x-reg.h"
> > +#include "88pm886-reg.h"
>
> Why are all of these required?
>
> > +#define PM88X_RTC_NAME "88pm88x-rtc"
> > +#define PM88X_ONKEY_NAME "88pm88x-onkey"
> > +#define PM88X_CHARGER_NAME "88pm88x-charger"
> > +#define PM88X_BATTERY_NAME "88pm88x-battery"
> > +#define PM88X_HEADSET_NAME "88pm88x-headset"
> > +#define PM88X_VBUS_NAME "88pm88x-vbus"
> > +#define PM88X_CFD_NAME "88pm88x-leds"
> > +#define PM88X_RGB_NAME "88pm88x-rgb"
> > +#define PM88X_GPADC_NAME "88pm88x-gpadc"
> > +#define PM88X_DVC_NAME "88pm88x-dvc"
>
> I would prefer that you just used the name directly.
>
> > +enum pm88x_type {
> > + PM886 = 1,
> > + PM880 = 2,
> > +};
> > +
> > +enum pm88x_pages {
> > + PM88X_BASE_PAGE = 0,
> > + PM88X_LDO_PAGE,
> > + PM88X_GPADC_PAGE,
> > + PM88X_BATTERY_PAGE,
> > + PM88X_BUCK_PAGE = 4,
>
> This is 4 anyway.
>
> > + PM88X_TEST_PAGE = 7,
> > +};
> > +
> > +enum pm88x_gpadc {
> > + PM88X_NO_GPADC = -1,
> > + PM88X_GPADC0 = 0,
> > + PM88X_GPADC1,
> > + PM88X_GPADC2,
> > + PM88X_GPADC3,
> > +};
> > +
> > +/* interrupt number */
> > +enum pm88x_irq_number {
> > + PM88X_IRQ_ONKEY, /* EN1b0 *//* 0 */
>
> At least put a space between the comments.
Yes, you are right, a space between the comments is more readable
>
> > + PM88X_IRQ_EXTON, /* EN1b1 */
> > + PM88X_IRQ_CHG_GOOD, /* EN1b2 */
> > + PM88X_IRQ_BAT_DET, /* EN1b3 */
> > + PM88X_IRQ_RTC, /* EN1b4 */
> > + PM88X_IRQ_CLASSD, /* EN1b5 *//* 5 */
> > + PM88X_IRQ_XO, /* EN1b6 */
> > + PM88X_IRQ_GPIO, /* EN1b7 */
> > +
> > + PM88X_IRQ_VBAT, /* EN2b0 *//* 8 */
> > + /* EN2b1 */
> > + PM88X_IRQ_VBUS, /* EN2b2 */
> > + PM88X_IRQ_ITEMP, /* EN2b3 *//* 10 */
> > + PM88X_IRQ_BUCK_PGOOD, /* EN2b4 */
> > + PM88X_IRQ_LDO_PGOOD, /* EN2b5 */
> > +
> > + PM88X_IRQ_GPADC0, /* EN3b0 */
> > + PM88X_IRQ_GPADC1, /* EN3b1 */
> > + PM88X_IRQ_GPADC2, /* EN3b2 *//* 15 */
> > + PM88X_IRQ_GPADC3, /* EN3b3 */
> > + PM88X_IRQ_MIC_DET, /* EN3b4 */
> > + PM88X_IRQ_HS_DET, /* EN3b5 */
> > + PM88X_IRQ_GND_DET, /* EN3b6 */
> > +
> > + PM88X_IRQ_CHG_FAIL, /* EN4b0 *//* 20 */
> > + PM88X_IRQ_CHG_DONE, /* EN4b1 */
> > + /* EN4b2 */
> > + PM88X_IRQ_CFD_FAIL, /* EN4b3 */
> > + PM88X_IRQ_OTG_FAIL, /* EN4b4 */
> > + PM88X_IRQ_CHG_ILIM, /* EN4b5 *//* 25 */
> > + /* EN4b6 */
> > + PM88X_IRQ_CC, /* EN4b7 *//* 27 */
> > +
> > + PM88X_MAX_IRQ, /* 28 */
> > +};
> > +
> > +/* 3 rgb led indicators */
> > +enum {
> > + PM88X_RGB_LED0,
> > + PM88X_RGB_LED1,
> > + PM88X_RGB_LED2,
> > +};
> > +
> > +/* camera flash/torch */
> > +enum {
> > + PM88X_NO_LED = -1,
> > + PM88X_FLASH_LED = 0,
> > + PM88X_TORCH_LED,
> > +};
> > +
> > +struct pm88x_dvc_ops {
> > + void (*level_to_reg)(u8 level);
> > +};
>
> This appears to be unused.

again, I think I should move it into next patch
>
> > +struct pm88x_buck1_dvc_desc {
> > + u8 current_reg;
> > + int max_level;
> > + int uV_step1;
> > + int uV_step2;
> > + int min_uV;
> > + int mid_uV;
> > + int max_uV;
> > + int mid_reg_val;
> > +};
> >
> > +struct pm88x_dvc {
> > + struct device *dev;
> > + struct pm88x_chip *chip;
> > + struct pm88x_dvc_ops ops;
> > + struct pm88x_buck1_dvc_desc desc;
> > +};
> > +
> > +struct pm88x_chip {
> > + struct i2c_client *client;
> > + struct device *dev;
> > +
> > + struct i2c_client *ldo_page; /* chip client for ldo page */
> > + struct i2c_client *power_page; /* chip client for power page */
> > + struct i2c_client *gpadc_page; /* chip client for gpadc page */
> > + struct i2c_client *battery_page;/* chip client for battery page */
> > + struct i2c_client *buck_page; /* chip client for buck page */
> > + struct i2c_client *test_page; /* chip client for test page */
> > +
> > + struct regmap *base_regmap;
> > + struct regmap *ldo_regmap;
> > + struct regmap *power_regmap;
> > + struct regmap *gpadc_regmap;
> > + struct regmap *battery_regmap;
> > + struct regmap *buck_regmap;
> > + struct regmap *test_regmap;
> > + struct regmap *codec_regmap;
> > +
> > + unsigned short ldo_page_addr; /* ldo page I2C address */
> > + unsigned short power_page_addr; /* power page I2C address */
> > + unsigned short gpadc_page_addr; /* gpadc page I2C address */
> > + unsigned short battery_page_addr;/* battery page I2C address */
> > + unsigned short buck_page_addr; /* buck page I2C address */
> > + unsigned short test_page_addr; /* test page I2C address */
> > +
> > + unsigned int chip_id;
> > + long type; /* specific chip */
> > + int irq;
> > +
> > + int irq_mode; /* write/read clear */
> > + struct regmap_irq_chip_data *irq_data;
> > +
> > + bool rtc_wakeup; /* is it powered up by expired alarm? */
> > + u8 powerdown1; /* save power down reason */
> > + u8 powerdown2;
> > + u8 powerup; /* the reason of power on */
> > +
> > + struct notifier_block reboot_notifier;
> > + struct pm88x_dvc *dvc;
> > +};
>
> This is an awful lot of junk to be held in a device data structure.
> Try to remove as much as you can.

thanks, I will think carefully
>
> > +extern struct regmap_irq_chip pm88x_irq_chip;
> > +extern const struct of_device_id pm88x_of_match[];
> > +
> > +struct pm88x_chip *pm88x_init_chip(struct i2c_client *client);
> > +int pm88x_parse_dt(struct device_node *np, struct pm88x_chip *chip);
> > +
> > +int pm88x_init_pages(struct pm88x_chip *chip);
> > +int pm88x_post_init_chip(struct pm88x_chip *chip);
> > +void pm800_exit_pages(struct pm88x_chip *chip);
> > +
> > +int pm88x_init_subdev(struct pm88x_chip *chip);
> > +long pm88x_of_get_type(struct device *dev);
> > +void pm88x_dev_exit(struct pm88x_chip *chip);
> > +
> > +int pm88x_irq_init(struct pm88x_chip *chip);
> > +int pm88x_irq_exit(struct pm88x_chip *chip);
> > +int pm88x_apply_patch(struct pm88x_chip *chip);
> > +int pm88x_stepping_fixup(struct pm88x_chip *chip);
> > +int pm88x_apply_board_fixup(struct pm88x_chip *chip, struct device_node *np);
> > +
> > +struct pm88x_chip *pm88x_get_chip(void);
> > +void pm88x_set_chip(struct pm88x_chip *chip);
> > +void pm88x_power_off(void);
> > +int pm88x_reboot_notifier_callback(struct notifier_block *nb,
> > + unsigned long code, void *unused);
>
> All of these should probably be moved into a single file, unless you
> have a good reason to spread them out?

thanks; I will modify it;
>
> > +#endif /* __LINUX_MFD_88PM88X_H */
>
> --
> Lee Jones
> Linaro STMicroelectronics Landing Team Lead
> Linaro.org â Open source software for ARM SoCs
> Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Sudeep Holla: "Re: [PATCH] clockevents: return error from tick_broadcast_oneshot_control if !GENERIC_CLOCKEVENTS_BROADCAST"
Previous message: Preeti U Murthy: "Re: [PATCH] clockevents: return error from tick_broadcast_oneshot_control if !GENERIC_CLOCKEVENTS_BROADCAST"
In reply to: Lee Jones: "Re: [PATCH V2 2/2] mfd: 88pm88x: initialize 88pm886/88pm880 base support"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]