Re: [PATCH 2/2] serial: 8250: Allow to skip autoconfig_irq() for a console

[Peter Hurley]

Hi Taichi,

On 06/05/2015 06:03 AM, Taichi Kageyama wrote:
> This patch provides a new parameter as a workaround of the following
> problem. It allows us to skip autoconfig_irq() and to use a well-known irq
> number for a console even if CONFIG_SERIAL_8250_DETECT_IRQ is defined.
> 
> There're cases where autoconfig_irq() fails during boot.
> In these cases, the console doesn't work in interrupt mode,
> the mode cannot be changed anymore, and "input overrun"
> (which can make operation mistakes) happens easily.
> This problem happens with high rate every boot once it occurs
> because the boot sequence is always almost same.
> 
> autoconfig_irq() assumes that a CPU can handle an interrupt from a serial
> during the waiting time, but there're some cases where the CPU cannot
> handle the interrupt for longer than the time. It completely depends on
> how other functions work on the CPU. Ideally, autoconfig_irq() should be
> fixed

It completely depends on how long some other driver has interrupts disabled,
which is a problem that needs fixed _in that driver_. autoconfig_irq() does not
need fixing.

A typical cause of this behavior is printk spew from overly-instrumented
debugging of some driver (trace_printk is better suited to heavy instrumentation).

Regards,
Peter Hurley


> to control these cases but as long as auto_irq algorithm is used,
> it's hard to know which CPU can handle an interrupt from a serial and
> to assure the interrupt of the CPU is enabled during auto_irq.
> Meanwhile for legacy consoles, they actually don't require auto_irq
> because they basically use well-known irq number.
> For non-console serials, this workaround is not required
> because setserial command can kick autoconfig_irq() again for them.
> 
> Signed-off-by: Taichi Kageyama <t-kageyama@xxxxxxxxxxxxx>
> Cc: Naoya Horiguchi <n-horiguchi@xxxxxxxxxxxxx>
> ---
>   drivers/tty/serial/8250/8250_core.c |   17 +++++++++++++++++
>   1 files changed, 17 insertions(+), 0 deletions(-)
> 
> diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
> index 6bf31f2..60fda28 100644
> --- a/drivers/tty/serial/8250/8250_core.c
> +++ b/drivers/tty/serial/8250/8250_core.c
> @@ -65,6 +65,8 @@ static int serial_index(struct uart_port *port)
> 
>   static unsigned int skip_txen_test; /* force skip of txen test at init time */
> 
> +static unsigned int skip_cons_autoirq; /* force skip autoirq for console */
> +
>   /*
>    * Debugging.
>    */
> @@ -3336,6 +3338,9 @@ serial8250_register_ports(struct uart_driver *drv, struct device *dev)
>   		if (skip_txen_test)
>   			up->port.flags |= UPF_NO_TXEN_TEST;
> 
> +		if (uart_console(&up->port) && skip_cons_autoirq)
> +			up->port.flags &= ~UPF_AUTO_IRQ;
> +
>   		uart_add_one_port(drv, &up->port);
>   	}
>   }
> @@ -3875,6 +3880,9 @@ int serial8250_register_8250_port(struct uart_8250_port *up)
>   		if (skip_txen_test)
>   			uart->port.flags |= UPF_NO_TXEN_TEST;
> 
> +		if (uart_console(&uart->port) && skip_cons_autoirq)
> +			uart->port.flags &= ~UPF_AUTO_IRQ;
> +
>   		if (up->port.flags & UPF_FIXED_TYPE)
>   			uart->port.type = up->port.type;
> 
> @@ -3936,6 +3944,10 @@ void serial8250_unregister_port(int line)
>   		uart->port.flags &= ~UPF_BOOT_AUTOCONF;
>   		if (skip_txen_test)
>   			uart->port.flags |= UPF_NO_TXEN_TEST;
> +
> +		if (uart_console(&uart->port) && skip_cons_autoirq)
> +			uart->port.flags &= ~UPF_AUTO_IRQ;
> +
>   		uart->port.type = PORT_UNKNOWN;
>   		uart->port.dev = &serial8250_isa_devs->dev;
>   		uart->capabilities = 0;
> @@ -4044,6 +4056,9 @@ MODULE_PARM_DESC(nr_uarts, "Maximum number of UARTs supported. (1-" __MODULE_STR
>   module_param(skip_txen_test, uint, 0644);
>   MODULE_PARM_DESC(skip_txen_test, "Skip checking for the TXEN bug at init time");
> 
> +module_param(skip_cons_autoirq, uint, 0644);
> +MODULE_PARM_DESC(skip_cons_autoirq, "Skip auto irq for console during boot");
> +
>   #ifdef CONFIG_SERIAL_8250_RSA
>   module_param_array(probe_rsa, ulong, &probe_rsa_count, 0444);
>   MODULE_PARM_DESC(probe_rsa, "Probe I/O ports for RSA");
> @@ -4070,6 +4085,8 @@ static void __used s8250_options(void)
>   	module_param_cb(share_irqs, &param_ops_uint, &share_irqs, 0644);
>   	module_param_cb(nr_uarts, &param_ops_uint, &nr_uarts, 0644);
>   	module_param_cb(skip_txen_test, &param_ops_uint, &skip_txen_test, 0644);
> +	module_param_cb(skip_cons_autoirq, &param_ops_uint,
> +		&skip_cons_autoirq, 0644);
>   #ifdef CONFIG_SERIAL_8250_RSA
>   	__module_param_call(MODULE_PARAM_PREFIX, probe_rsa,
>   		&param_array_ops, .arr = &__param_arr_probe_rsa,
> 

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/