On Tue, 11 Aug 2015 10:25:47 +0100
Grygorii Strashko <grygorii.strashko@xxxxxx> wrote:
Hi Grygorii,
It's observed that ARM GIC IRQ triggering type is not configured
properly when IRQ is routed through IRQ domains hierarchy and
system started using DT. As result, system will start using default
ARM GIC configuration, ignore DT IRQ type configuration,
and value of desc->irq_data.state_use_accessors = 0.
In case of TI OMAP the following IRQ hierarchy is defined:
ARM GIC <- OMAP wakeupgen <- TI CBAR
Failed call chain:
irq_create_of_mapping
irq_set_irq_type
__irq_set_trigger
if (!chip || !chip->irq_set_type) {
return 0; <- return here
}
CBAR has no .irq_set_type() defined and, so, IRQ triggering
configuration will not be propagated to parent IRQ domain.
Hence, fix it by introducing irq_chip_set_type_parent(), in the
same manner as irq_chip_set_wake_parent(), and use it for IRQ
triggering type propagation to the parent IRQ domain in
irq-crossbar and omap-wakeupgen.
/ # cat /proc/interrupts -- before
230: 0 0 CBAR 30 Edge -00000000 48051000.gpio
263: 0 0 CBAR 116 Edge -00000000 48053000.gpio
296: 246 0 CBAR 67 Edge -00000000 OMAP UART0
311: 341 0 CBAR 51 Edge -00000000 48070000.i2c
312: 3 0 CBAR 52 Edge -00000000 48072000.i2c
313: 0 0 CBAR 56 Edge -00000000 48060000.i2c
314: 255 0 CBAR 78 Edge -00000000 mmc0
315: 40 0 CBAR 81 Edge -00000000 mmc1
316: 13 0 CBAR 91 Edge -00000000 mmc2
320: 0 0 CBAR 49 Edge -00000000 4a140000.sata
324: 0 0 CBAR 1 Edge -00000000 48078000.elm
325: 0 0 CBAR 15 Edge -00000000 gpmc
333: 0 0 CBAR 335 Edge -00000000 48484000.ethernet
334: 0 0 CBAR 336 Edge -00000000 48484000.ethernet
415: 0 0 pcf857x 2 Edge -00000000 btnUser1
416: 0 0 pcf857x 3 Edge -00000000 btnUser2
445: 0 0 pinctrl 992 Edge -00010000 4806a000.seria
/ # cat /proc/interrupts -- after
230: 0 0 CBAR 30 Level -00002004 48051000.gpio
263: 0 0 CBAR 116 Level -00002004 48053000.gpio
296: 567 0 CBAR 67 Level -00002004 OMAP UART0
311: 363 0 CBAR 51 Level -00002004 48070000.i2c
312: 3 0 CBAR 52 Level -00002004 48072000.i2c
313: 0 0 CBAR 56 Level -00002004 48060000.i2c
314: 197 0 CBAR 78 Level -00002004 mmc0
315: 40 0 CBAR 81 Level -00002004 mmc1
316: 13 0 CBAR 91 Level -00002004 mmc2
320: 0 0 CBAR 49 Level -00002004 4a140000.sata
324: 0 0 CBAR 1 Level -00002004 48078000.elm
325: 0 0 CBAR 15 Level -00002004 gpmc
333: 0 0 CBAR 335 Level -00002004 48484000.ethernet
334: 0 0 CBAR 336 Level -00002004 48484000.ethernet
415: 0 0 pcf857x 2 Edge -00000000 btnUser1
416: 4 2 pcf857x 3 Edge -00000000 btnUser2
445: 0 0 pinctrl 992 Edge -00010000 4806a000.serial
Fixes: 783d31863fb8 ('irqchip: crossbar: Convert dra7 crossbar to stacked domains')
Signed-off-by: Grygorii Strashko <grygorii.strashko@xxxxxx>
---
Hi All,
I can split patch if required and overall solution acceptable.
This looks good to me. Please repost it after splitting it in two
patches.