Re: [PATCH 0/4] UART slave device support - version 4

From: NeilBrown
Date: Tue Aug 11 2015 - 19:22:08 EST


On Fri, 7 Aug 2015 15:01:47 +0200 Linus Walleij
<linus.walleij@xxxxxxxxxx> wrote:

> Hi Neil,
>
> first, this is a *VERY* interesting and much needed patch series,
> I intend to look closer at it, and if possible test it with some
> (heh) board file device. Would be happy of you put me on CC for these.
>
> On Mon, May 11, 2015 at 3:56 AM, NeilBrown <neil@xxxxxxxxxx> wrote:
>
> > When a device is connected to a UART via RS-232 (or similar), there
> > is a DTR line that can be used for power management, and other "modem
> > control" lines.
> >
> > On an embedded board, it is very likely that there is no "DTR", and
> > any power management need to be done using some completely separate
> > mechanism.
> >
> > So these "slaves" are really just for devices permanently attached to
> > UARTs without a full "RS-232" (or similar) connection. The driver
> > does all the extra control beyond Tx/Rx.
>
> What is usually happening (and I have seen it in a few places) is that
> the SoC has *one* fully featured RS232 with CTS/RTS and even
> DTS,DCD,RI and other esoterica, which is intended to be connected to a
> host serial port or so, for example if this SoC is to act as a modem
> or a fax machine, or if it is to drive one.
>
> Then they often have a few more UART blocks, usually identical, which
> only have RxD+TxD available, so they are "just" UARTs.
>
> To complicate things further, you may wonder what happened with
> the CTS/RTS (etc) signals from the other blocks. Usually they are there
> in the silicon but just routed to dead ends.
>
> To complicate it even further, usually all these pins are placed under
> pin control multiplexing, so in an actual electronic design, the
> system will mux out CTS/RTS (etc) from the fully featured RS232
> blocks and only use them as UARTs anyways.
>
> Then there are those who created real simple RxD/TxD-only UARTs
> ("yeah lets dump this RS232 legacy crap" / "yeah yeah")
> and then realized they want to drive modems ("oh crap, it seemed
> like a good idea at the time"). Then they usually take
> two GPIO pins for CTS/RTS and drive them as GPIOs using
> software and you have a cheap 4-line modem line. This is what
> drivers/tty/serial/serial_mctrl_gpio.c is for if you wondered.
>
> > I've tested this set and it seems to work ... except that something
> > is sadly broken with bluetooth support in 4.1-rc1 so I've only really
> > tested the GPS driver. I guess it is time to rebase to -rc3.
>
> You have a hardware taget I see. Which one?

GTA04 (www.gta04.org - openmoko successor).

3 uarts on OMAP3 are wired: one as RS-232 for console, one to bluetooth
half of a wifi/bluetooth module, and one to a GPS.

For the GPS, I just want to power on/off when the TTY is opened/closed,
but the power-on sequence is non-trivial as both "turn on" and
"turn-off' toggle the same line, so I need to be able to detect current
state.

For the bluetooth, the power is a (shared) regulator. As well as
power-on when the TTY is opened, I'd like regulator to be turned of
when I "hciconfig down" - even though the TTY is still open.
I did a patch a while ago which hooked in to hci_uart_{open,close} to
make this work, but it isn't a really good patch.

It would be nice to hide the TTY from user-space in the bluetooth case,
and have the "hciattach" happen in the kernel, but I think hciattach
does extra initialisation...

NeilBrown


--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/