Re: [PATCH v3 0/3] Add support for touchscreen on Colibri VF50

[maitysanchayan]

Hello,

Ping?

- Sanchayan.

On 15-08-05 14:25:48, Sanchayan Maity wrote:
> Hello,
> 
> The patchset adds support for 4 wire touchscreen on Toradex Colibri
> VF50 modules. Patches are tested on top of shawn's for-next branch.
> 
> Changes since v2:
> 1. Fix pin multiplexing for pins in idle state. Configuration of the
> pen detect pull up viz. PTA19__GPIO_9 resulted in generation of pen
> irq's on a continuous basis.
> 2. Fix pinmux of the ADC pins as per the recommended pinmux in TRM.
> 3. Use a threaded irq handler instead of a irq handler plus workqueue
> approach.
> 4. Use a low level trigger with oneshot flag specifier instead of the
> previous falling edge triggered irq's. This coupled with the fix in
> point 1 fixes the previous continuous spurious irq generation bug.
> 5. Change/fix the TS measurement logic to account for the fact that
> iio_channel_read_raw might actually return an error. To be more
> specific use break instead of continue and take care to close the
> FET's in case of channel read error.
> 6. Drop the first patch "Add io-channel-cells property for ADC node"
> as it has already been applied.
> 7. Move the iio channel get call again at the start. Having it in
> the end resulted in crashes sometimes when iio was not probed and
> the ts device got probed and opened earlier.
> 
> Changes since v1:
> 1. Fix/drop comments
> 2. Use an inline function for multiple gpiod_get calls in probe
> 3. Remove the pull up in the pinmux specified in DT for touchctrl_gpios
> 4. Add the io-channel-cells property before status property.
> 5. Add GPIOLIB as dependency in the Kconfig file
> 
> Version 2 of the patchset can be found here
> https://www.mail-archive.com/linux-input@xxxxxxxxxxxxxxx/msg18090.html
> 
> Version 1 of the patchset can be found here
> https://lkml.org/lkml/2015/6/30/103
> 
> Thank you very much for the feedback till now.
> 
> Regards,
> Sanchayan.
> 
> Sanchayan Maity (3):
>   ARM: dts: vf500-colibri: Add device tree node for touchscreen support
>   input: Add DT binding documentation for Colibri VF50 touchscreen
>   touchscreen: colibri-vf50-ts: Add touchscreen support for Colibri VF50
> 
>  .../bindings/input/touchscreen/colibri-vf50-ts.txt |  32 ++
>  arch/arm/boot/dts/vf500-colibri-eval-v3.dts        |   4 +
>  arch/arm/boot/dts/vf500-colibri.dtsi               |  45 +++
>  drivers/input/touchscreen/Kconfig                  |  12 +
>  drivers/input/touchscreen/Makefile                 |   1 +
>  drivers/input/touchscreen/colibri-vf50-ts.c        | 404 +++++++++++++++++++++
>  6 files changed, 498 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt
>  create mode 100644 drivers/input/touchscreen/colibri-vf50-ts.c
> 
> -- 
> 2.5.0
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/