[RFC V2] fs/kcore: change copy_to_user to copy_in_user

[yalin wang]

The copy_to_user() here expect can fix the fault on both kernel and
user address, this is not true on other platforms except x86,
change to user copy_in_user() so that can detect the source and
destination address page fault, work as expected:

ENTRY(copy_user_generic_string)
	ASM_STAC
	cmpl $8,%edx
	jb 2f		/* less than 8 bytes, go to byte copy loop */
	ALIGN_DESTINATION
	movl %edx,%ecx
	shrl $3,%ecx
	andl $7,%edx
1:	rep
	movsq
2:	movl %edx,%ecx
3:	rep
	movsb
	xorl %eax,%eax
	ASM_CLAC
	ret

	.section .fixup,"ax"
11:	leal (%rdx,%rcx,8),%ecx
12:	movl %ecx,%edx		/* ecx is zerorest also */
	jmp copy_user_handle_tail
	.previous

	_ASM_EXTABLE(1b,11b)
	_ASM_EXTABLE(3b,12b)
ENDPROC(copy_user_generic_string)

This is the x86 copy_to_user implementation, the fault instruction is
label 1b, 3b, because movsb instruction will fault on both source and
destination address, but on other platforms, like arm64 and arm:

ENTRY(__copy_to_user)
ALTERNATIVE("nop", __stringify(SET_PSTATE_PAN(0)), ARM64_HAS_PAN, \
	    CONFIG_ARM64_PAN)
	add	x5, x0, x2			// upper user buffer boundary
	subs	x2, x2, #16
	b.mi	1f
0:
	ldp	x3, x4, [x1], #16
	subs	x2, x2, #16
USER(9f, stp	x3, x4, [x0], #16)
	b.pl	0b
1:	adds	x2, x2, #8
	b.mi	2f
	ldr	x3, [x1], #8
	sub	x2, x2, #8
USER(9f, str	x3, [x0], #8	)
2:	adds	x2, x2, #4
	b.mi	3f
	ldr	w3, [x1], #4
	sub	x2, x2, #4
USER(9f, str	w3, [x0], #4	)
3:	adds	x2, x2, #2
	b.mi	4f
	ldrh	w3, [x1], #2
	sub	x2, x2, #2
USER(9f, strh	w3, [x0], #2	)
4:	adds	x2, x2, #1
	b.mi	5f
	ldrb	w3, [x1]
USER(9f, strb	w3, [x0]	)
5:	mov	x0, #0

It only check the str instructions, means only check fault on destination
address, if the source address in kernel is invalid, it will result in
kernel panic(), this may happened in read_kcore() function, the
kern_addr_valid() only make sure the address is valid during call it,
when it returned, the kernel address may be invalid, like kunmap(),
setfixmap(), vfree() function will change kernel pagetables, and there is
not any sync between read_kcore() and kernel pagetable change. I change
to use copy_in_user(), so that can check both source and destination address,
avoid the kernel panic() in some unlucky circumstance.

Signed-off-by: yalin wang <yalin.wang2010@xxxxxxxxx>
---
 fs/proc/kcore.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/fs/proc/kcore.c b/fs/proc/kcore.c
index 92e6726..4f28deb 100644
--- a/fs/proc/kcore.c
+++ b/fs/proc/kcore.c
@@ -515,8 +515,12 @@ read_kcore(struct file *file, char __user *buffer, size_t buflen, loff_t *fpos)
 		} else {
 			if (kern_addr_valid(start)) {
 				unsigned long n;
-
-				n = copy_to_user(buffer, (char *)start, tsz);
+				if ((start + tsz < tsz) ||
+						(start + tsz) > TASK_SIZE)
+					return -EFAULT;
+				set_fs(KERNEL_DS);
+				n = copy_in_user(buffer, (char *)start, tsz);
+				set_fs(USER_DS);
 				/*
 				 * We cannot distinguish between fault on source
 				 * and fault on destination. When this happens
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/