[PATCH v3 11/13] Documentation: devicetree: ufs: Add DT bindings for exynos UFS host controller

From: Alim Akhtar
Date: Thu Oct 01 2015 - 04:25:32 EST


From: Seungwon Jeon <essuuj@xxxxxxxxx>

This adds Exynos Universal Flash Storage (UFS) Host Controller DT bindings.

Signed-off-by: Seungwon Jeon <essuuj@xxxxxxxxx>
Signed-off-by: Alim Akhtar <alim.akhtar@xxxxxxxxxxx>
---
.../devicetree/bindings/ufs/ufs-exynos.txt | 93 ++++++++++++++++++++
1 file changed, 93 insertions(+)
create mode 100644 Documentation/devicetree/bindings/ufs/ufs-exynos.txt

diff --git a/Documentation/devicetree/bindings/ufs/ufs-exynos.txt b/Documentation/devicetree/bindings/ufs/ufs-exynos.txt
new file mode 100644
index 0000000..00df72e
--- /dev/null
+++ b/Documentation/devicetree/bindings/ufs/ufs-exynos.txt
@@ -0,0 +1,93 @@
+* Exynos Universal Flash Storage (UFS) Host Controller
+
+UFSHC nodes are defined to describe on-chip UFS host controllers.
+Each UFS controller instance should have its own node.
+
+Required properties:
+- compatible : compatible name, contains "samsung,exynos7-ufs"
+- interrupts : <interrupt mapping for UFS host controller IRQ>
+- reg : <registers mapping>
+
+Optional properties:
+- vdd-hba-supply : phandle to UFS host controller supply regulator node
+- vcc-supply : phandle to VCC supply regulator node
+- vccq-supply : phandle to VCCQ supply regulator node
+- vccq2-supply : phandle to VCCQ2 supply regulator node
+- vcc-supply-1p8 : For embedded UFS devices, valid VCC range is 1.7-1.95V
+ or 2.7-3.6V. This boolean property when set, specifies
+ to use low voltage range of 1.7-1.95V. Note for external
+ UFS cards this property is invalid and valid VCC range is
+ always 2.7-3.6V.
+- vcc-max-microamp : specifies max. load that can be drawn from vcc supply
+- vccq-max-microamp : specifies max. load that can be drawn from vccq supply
+- vccq2-max-microamp : specifies max. load that can be drawn from vccq2 supply
+- <name>-fixed-regulator : boolean property specifying that <name>-supply is a fixed regulator
+
+- clocks : List of phandle and clock specifier pairs
+- clock-names : List of clock input name strings sorted in the same
+ order as the clocks property.
+- freq-table-hz : Array of <min max> operating frequencies stored in the same
+ order as the clocks property. If this property is not
+ defined or a value in the array is "0" then it is assumed
+ that the frequency is set by the parent clock or a
+ fixed rate clock source.
+- pclk-freq-avail-range : specifies available frequency range(min/max) for APB clock
+- ufs,pwr-attr-mode : specifies mode value for power mode change
+- ufs,pwr-attr-lane : specifies lane count value for power mode change
+- ufs,pwr-attr-gear : specifies gear count value for power mode change
+- ufs,pwr-attr-hs-series : specifies HS rate series for power mode change
+- ufs,pwr-local-l2-timer : specifies array of local UNIPRO L2 timer values
+ <FC0ProtectionTimeOutVal,TC0ReplayTimeOutVal, AFC0ReqTimeOutVal>
+- ufs,pwr-remote-l2-timer : specifies array of remote UNIPRO L2 timer values
+ <FC0ProtectionTimeOutVal,TC0ReplayTimeOutVal, AFC0ReqTimeOutVal>
+- ufs-rx-adv-fine-gran-sup_en : specifies support of fine granularity of MPHY,
+ this is a boolean property.
+- ufs-rx-adv-fine-gran-step : specifies granularity steps of MPHY
+- ufs-rx-adv-min-activate-time-cap : specifies rx advanced minimum activate time of MPHY
+- ufs-pa-granularity : specifies Granularity for PA_TActivate and PA_Hibern8Time
+- ufs-pa-tacctivate : specifies time wake-up remote M-RX
+- ufs-pa-hibern8time : specifies minimum time to wait in HIBERN8 state
+
+Note: If above properties are not defined it can be assumed that the supply
+regulators or clocks are always on.
+
+Example:
+ ufshc@0x15570000 {
+ compatible = "samsung,exynos7-ufs";
+ reg = <0xfc598000 0x800>;
+ reg = <0x15570000 0x100>,
+ <0x15570100 0x100>,
+ <0x15571000 0x200>,
+ <0x15572000 0x300>;
+ reg-names = "hci", "vs_hci", "unipro", "ufsp";
+ interrupts = <0 200 0>;
+
+ vdd-hba-supply = <&xxx_reg0>;
+ vdd-hba-fixed-regulator;
+ vcc-supply = <&xxx_reg1>;
+ vcc-supply-1p8;
+ vccq-supply = <&xxx_reg2>;
+ vccq2-supply = <&xxx_reg3>;
+ vcc-max-microamp = 500000;
+ vccq-max-microamp = 200000;
+ vccq2-max-microamp = 200000;
+
+ clocks = <&core 0>, <&ref 0>, <&iface 0>;
+ clock-names = "core_clk", "ref_clk", "iface_clk";
+ freq-table-hz = <100000000 200000000>, <0 0>, <0 0>;
+
+ pclk-freq-avail-range = <70000000 133000000>;
+
+ ufs,pwr-attr-mode = "FAST";
+ ufs,pwr-attr-lane = /bits/ 8 <2>;
+ ufs,pwr-attr-gear = /bits/ 8 <2>;
+ ufs,pwr-attr-hs-series = "HS_rate_b";
+ ufs,pwr-local-l2-timer = <8000 28000 20000>;
+ ufs,pwr-remote-l2-timer = <12000 32000 16000>;
+ ufs-rx-adv-fine-gran-sup_en = <1>;
+ ufs-rx-adv-fine-gran-step = <3>;
+ ufs-rx-adv-min-activate-time-cap = <10>;
+ ufs-pa-granularity = <6>;
+ ufs-pa-tacctivate = <6>;
+ ufs-pa-hibern8time = <20>;
+ };
--
1.7.10.4

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/