Re: [PATCH v3 3/5] net: phy: Add Broadcom phy library for common interfaces
From: Florian Fainelli
Date: Wed Oct 14 2015 - 13:39:03 EST
On 14/10/15 10:33, Robert E Cochran wrote:
>
>
> On 10/06/2015 03:25 PM, Arun Parameswaran wrote:
>> This patch adds the Broadcom phy library to consolidate common
>> interfaces shared by Broadcom phy's.
>
> The BCM54612E is included in the Broadcom Community part portfolio
> (https://community.broadcom.com). However, I don't see this part
> explicitly supported by your phy library ( e.g., not included in
> broadcom_drivers[] in broadcom.c ).
These are external PHY products which have a different support channel
and engineering teams.
>
> Can you please comment on whether this part is supported or the extent
> of changes required to establish and support a robust GigE connection
> between RGMII and CU?
This probably deserves a separate thread rather than hijacking an
existing one?
>
> We're considering this part for a new embedded design, and we need an
> open source driver for it.
>
> Thanks
>
> Bob
>
>
>
>>
>> Moved the common interfaces to the 'bcm-phy-lib.c' and updated
>> the Broadcom PHY drivers to use the new APIs.
>>
>> Signed-off-by: Arun Parameswaran <arunp@xxxxxxxxxxxx>
>> ---
>> drivers/net/phy/Kconfig | 6 ++
>> drivers/net/phy/Makefile | 1 +
>> drivers/net/phy/bcm-phy-lib.c | 209
>> ++++++++++++++++++++++++++++++++++++++++++
>> drivers/net/phy/bcm-phy-lib.h | 37 ++++++++
>> drivers/net/phy/bcm63xx.c | 38 +-------
>> drivers/net/phy/bcm7xxx.c | 127 ++++++-------------------
>> drivers/net/phy/broadcom.c | 149 +++++++++---------------------
>> include/linux/brcmphy.h | 22 +----
>> 8 files changed, 333 insertions(+), 256 deletions(-)
>> create mode 100644 drivers/net/phy/bcm-phy-lib.c
>> create mode 100644 drivers/net/phy/bcm-phy-lib.h
>>
>> diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
>> index b57f6c2..606fdc9 100644
>> --- a/drivers/net/phy/Kconfig
>> +++ b/drivers/net/phy/Kconfig
>> @@ -69,8 +69,12 @@ config SMSC_PHY
>> ---help---
>> Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs
>> +config BCM_NET_PHYLIB
>> + tristate
>> +
>> config BROADCOM_PHY
>> tristate "Drivers for Broadcom PHYs"
>> + select BCM_NET_PHYLIB
>> ---help---
>> Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S,
>> BCM5464,
>> BCM5481 and BCM5482 PHYs.
>> @@ -78,11 +82,13 @@ config BROADCOM_PHY
>> config BCM63XX_PHY
>> tristate "Drivers for Broadcom 63xx SOCs internal PHY"
>> depends on BCM63XX
>> + select BCM_NET_PHYLIB
>> ---help---
>> Currently supports the 6348 and 6358 PHYs.
>> config BCM7XXX_PHY
>> tristate "Drivers for Broadcom 7xxx SOCs internal PHYs"
>> + select BCM_NET_PHYLIB
>> ---help---
>> Currently supports the BCM7366, BCM7439, BCM7445, and
>> 40nm and 65nm generation of BCM7xxx Set Top Box SoCs.
>> diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
>> index f4e6eb9..6932475 100644
>> --- a/drivers/net/phy/Makefile
>> +++ b/drivers/net/phy/Makefile
>> @@ -12,6 +12,7 @@ obj-$(CONFIG_QSEMI_PHY) += qsemi.o
>> obj-$(CONFIG_SMSC_PHY) += smsc.o
>> obj-$(CONFIG_TERANETICS_PHY) += teranetics.o
>> obj-$(CONFIG_VITESSE_PHY) += vitesse.o
>> +obj-$(CONFIG_BCM_NET_PHYLIB) += bcm-phy-lib.o
>> obj-$(CONFIG_BROADCOM_PHY) += broadcom.o
>> obj-$(CONFIG_BCM63XX_PHY) += bcm63xx.o
>> obj-$(CONFIG_BCM7XXX_PHY) += bcm7xxx.o
>> diff --git a/drivers/net/phy/bcm-phy-lib.c
>> b/drivers/net/phy/bcm-phy-lib.c
>> new file mode 100644
>> index 0000000..13e161e
>> --- /dev/null
>> +++ b/drivers/net/phy/bcm-phy-lib.c
>> @@ -0,0 +1,209 @@
>> +/*
>> + * Copyright (C) 2015 Broadcom Corporation
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include "bcm-phy-lib.h"
>> +#include <linux/brcmphy.h>
>> +#include <linux/export.h>
>> +#include <linux/mdio.h>
>> +#include <linux/phy.h>
>> +
>> +#define MII_BCM_CHANNEL_WIDTH 0x2000
>> +#define BCM_CL45VEN_EEE_ADV 0x3c
>> +
>> +int bcm_phy_write_exp(struct phy_device *phydev, u16 reg, u16 val)
>> +{
>> + int rc;
>> +
>> + rc = phy_write(phydev, MII_BCM54XX_EXP_SEL, reg);
>> + if (rc < 0)
>> + return rc;
>> +
>> + return phy_write(phydev, MII_BCM54XX_EXP_DATA, val);
>> +}
>> +EXPORT_SYMBOL_GPL(bcm_phy_write_exp);
>> +
>> +int bcm_phy_read_exp(struct phy_device *phydev, u16 reg)
>> +{
>> + int val;
>> +
>> + val = phy_write(phydev, MII_BCM54XX_EXP_SEL, reg);
>> + if (val < 0)
>> + return val;
>> +
>> + val = phy_read(phydev, MII_BCM54XX_EXP_DATA);
>> +
>> + /* Restore default value. It's O.K. if this write fails. */
>> + phy_write(phydev, MII_BCM54XX_EXP_SEL, 0);
>> +
>> + return val;
>> +}
>> +EXPORT_SYMBOL_GPL(bcm_phy_read_exp);
>> +
>> +int bcm_phy_write_misc(struct phy_device *phydev,
>> + u16 reg, u16 chl, u16 val)
>> +{
>> + int rc;
>> + int tmp;
>> +
>> + rc = phy_write(phydev, MII_BCM54XX_AUX_CTL,
>> + MII_BCM54XX_AUXCTL_SHDWSEL_MISC);
>> + if (rc < 0)
>> + return rc;
>> +
>> + tmp = phy_read(phydev, MII_BCM54XX_AUX_CTL);
>> + tmp |= MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA;
>> + rc = phy_write(phydev, MII_BCM54XX_AUX_CTL, tmp);
>> + if (rc < 0)
>> + return rc;
>> +
>> + tmp = (chl * MII_BCM_CHANNEL_WIDTH) | reg;
>> + rc = bcm_phy_write_exp(phydev, tmp, val);
>> +
>> + return rc;
>> +}
>> +EXPORT_SYMBOL_GPL(bcm_phy_write_misc);
>> +
>> +int bcm_phy_read_misc(struct phy_device *phydev,
>> + u16 reg, u16 chl)
>> +{
>> + int rc;
>> + int tmp;
>> +
>> + rc = phy_write(phydev, MII_BCM54XX_AUX_CTL,
>> + MII_BCM54XX_AUXCTL_SHDWSEL_MISC);
>> + if (rc < 0)
>> + return rc;
>> +
>> + tmp = phy_read(phydev, MII_BCM54XX_AUX_CTL);
>> + tmp |= MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA;
>> + rc = phy_write(phydev, MII_BCM54XX_AUX_CTL, tmp);
>> + if (rc < 0)
>> + return rc;
>> +
>> + tmp = (chl * MII_BCM_CHANNEL_WIDTH) | reg;
>> + rc = bcm_phy_read_exp(phydev, tmp);
>> +
>> + return rc;
>> +}
>> +EXPORT_SYMBOL_GPL(bcm_phy_read_misc);
>> +
>> +int bcm_phy_ack_intr(struct phy_device *phydev)
>> +{
>> + int reg;
>> +
>> + /* Clear pending interrupts. */
>> + reg = phy_read(phydev, MII_BCM54XX_ISR);
>> + if (reg < 0)
>> + return reg;
>> +
>> + return 0;
>> +}
>> +EXPORT_SYMBOL_GPL(bcm_phy_ack_intr);
>> +
>> +int bcm_phy_config_intr(struct phy_device *phydev)
>> +{
>> + int reg;
>> +
>> + reg = phy_read(phydev, MII_BCM54XX_ECR);
>> + if (reg < 0)
>> + return reg;
>> +
>> + if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
>> + reg &= ~MII_BCM54XX_ECR_IM;
>> + else
>> + reg |= MII_BCM54XX_ECR_IM;
>> +
>> + return phy_write(phydev, MII_BCM54XX_ECR, reg);
>> +}
>> +EXPORT_SYMBOL_GPL(bcm_phy_config_intr);
>> +
>> +int bcm_phy_read_shadow(struct phy_device *phydev, u16 shadow)
>> +{
>> + phy_write(phydev, MII_BCM54XX_SHD, MII_BCM54XX_SHD_VAL(shadow));
>> + return MII_BCM54XX_SHD_DATA(phy_read(phydev, MII_BCM54XX_SHD));
>> +}
>> +EXPORT_SYMBOL_GPL(bcm_phy_read_shadow);
>> +
>> +int bcm_phy_write_shadow(struct phy_device *phydev, u16 shadow,
>> + u16 val)
>> +{
>> + return phy_write(phydev, MII_BCM54XX_SHD,
>> + MII_BCM54XX_SHD_WRITE |
>> + MII_BCM54XX_SHD_VAL(shadow) |
>> + MII_BCM54XX_SHD_DATA(val));
>> +}
>> +EXPORT_SYMBOL_GPL(bcm_phy_write_shadow);
>> +
>> +int bcm_phy_enable_apd(struct phy_device *phydev, bool dll_pwr_down)
>> +{
>> + int val;
>> +
>> + if (dll_pwr_down) {
>> + val = bcm_phy_read_shadow(phydev, BCM54XX_SHD_SCR3);
>> + if (val < 0)
>> + return val;
>> +
>> + val |= BCM54XX_SHD_SCR3_DLLAPD_DIS;
>> + bcm_phy_write_shadow(phydev, BCM54XX_SHD_SCR3, val);
>> + }
>> +
>> + val = bcm_phy_read_shadow(phydev, BCM54XX_SHD_APD);
>> + if (val < 0)
>> + return val;
>> +
>> + /* Clear APD bits */
>> + val &= BCM_APD_CLR_MASK;
>> +
>> + if (phydev->autoneg == AUTONEG_ENABLE)
>> + val |= BCM54XX_SHD_APD_EN;
>> + else
>> + val |= BCM_NO_ANEG_APD_EN;
>> +
>> + /* Enable energy detect single link pulse for easy wakeup */
>> + val |= BCM_APD_SINGLELP_EN;
>> +
>> + /* Enable Auto Power-Down (APD) for the PHY */
>> + return bcm_phy_write_shadow(phydev, BCM54XX_SHD_APD, val);
>> +}
>> +EXPORT_SYMBOL_GPL(bcm_phy_enable_apd);
>> +
>> +int bcm_phy_enable_eee(struct phy_device *phydev)
>> +{
>> + int val;
>> +
>> + /* Enable EEE at PHY level */
>> + val = phy_read_mmd_indirect(phydev, BRCM_CL45VEN_EEE_CONTROL,
>> + MDIO_MMD_AN, phydev->addr);
>> + if (val < 0)
>> + return val;
>> +
>> + val |= LPI_FEATURE_EN | LPI_FEATURE_EN_DIG1000X;
>> +
>> + phy_write_mmd_indirect(phydev, BRCM_CL45VEN_EEE_CONTROL,
>> + MDIO_MMD_AN, phydev->addr, (u32)val);
>> +
>> + /* Advertise EEE */
>> + val = phy_read_mmd_indirect(phydev, BCM_CL45VEN_EEE_ADV,
>> + MDIO_MMD_AN, phydev->addr);
>> + if (val < 0)
>> + return val;
>> +
>> + val |= (MDIO_AN_EEE_ADV_100TX | MDIO_AN_EEE_ADV_1000T);
>> +
>> + phy_write_mmd_indirect(phydev, BCM_CL45VEN_EEE_ADV,
>> + MDIO_MMD_AN, phydev->addr, (u32)val);
>> +
>> + return 0;
>> +}
>> +EXPORT_SYMBOL_GPL(bcm_phy_enable_eee);
>> +
>> diff --git a/drivers/net/phy/bcm-phy-lib.h
>> b/drivers/net/phy/bcm-phy-lib.h
>> new file mode 100644
>> index 0000000..b2091c8
>> --- /dev/null
>> +++ b/drivers/net/phy/bcm-phy-lib.h
>> @@ -0,0 +1,37 @@
>> +/*
>> + * Copyright (C) 2015 Broadcom Corporation
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#ifndef _LINUX_BCM_PHY_LIB_H
>> +#define _LINUX_BCM_PHY_LIB_H
>> +
>> +#include <linux/phy.h>
>> +
>> +int bcm_phy_write_exp(struct phy_device *phydev, u16 reg, u16 val);
>> +int bcm_phy_read_exp(struct phy_device *phydev, u16 reg);
>> +
>> +int bcm_phy_write_misc(struct phy_device *phydev,
>> + u16 reg, u16 chl, u16 value);
>> +int bcm_phy_read_misc(struct phy_device *phydev,
>> + u16 reg, u16 chl);
>> +
>> +int bcm_phy_write_shadow(struct phy_device *phydev, u16 shadow,
>> + u16 val);
>> +int bcm_phy_read_shadow(struct phy_device *phydev, u16 shadow);
>> +
>> +int bcm_phy_ack_intr(struct phy_device *phydev);
>> +int bcm_phy_config_intr(struct phy_device *phydev);
>> +
>> +int bcm_phy_enable_apd(struct phy_device *phydev, bool dll_pwr_down);
>> +
>> +int bcm_phy_enable_eee(struct phy_device *phydev);
>> +#endif /* _LINUX_BCM_PHY_LIB_H */
>> diff --git a/drivers/net/phy/bcm63xx.c b/drivers/net/phy/bcm63xx.c
>> index 830ec31..86b2805 100644
>> --- a/drivers/net/phy/bcm63xx.c
>> +++ b/drivers/net/phy/bcm63xx.c
>> @@ -6,6 +6,7 @@
>> * as published by the Free Software Foundation; either version
>> * 2 of the License, or (at your option) any later version.
>> */
>> +#include "bcm-phy-lib.h"
>> #include <linux/module.h>
>> #include <linux/phy.h>
>> @@ -42,35 +43,6 @@ static int bcm63xx_config_init(struct phy_device
>> *phydev)
>> return phy_write(phydev, MII_BCM63XX_IR, reg);
>> }
>> -static int bcm63xx_ack_interrupt(struct phy_device *phydev)
>> -{
>> - int reg;
>> -
>> - /* Clear pending interrupts. */
>> - reg = phy_read(phydev, MII_BCM63XX_IR);
>> - if (reg < 0)
>> - return reg;
>> -
>> - return 0;
>> -}
>> -
>> -static int bcm63xx_config_intr(struct phy_device *phydev)
>> -{
>> - int reg, err;
>> -
>> - reg = phy_read(phydev, MII_BCM63XX_IR);
>> - if (reg < 0)
>> - return reg;
>> -
>> - if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
>> - reg &= ~MII_BCM63XX_IR_GMASK;
>> - else
>> - reg |= MII_BCM63XX_IR_GMASK;
>> -
>> - err = phy_write(phydev, MII_BCM63XX_IR, reg);
>> - return err;
>> -}
>> -
>> static struct phy_driver bcm63xx_driver[] = {
>> {
>> .phy_id = 0x00406000,
>> @@ -82,8 +54,8 @@ static struct phy_driver bcm63xx_driver[] = {
>> .config_init = bcm63xx_config_init,
>> .config_aneg = genphy_config_aneg,
>> .read_status = genphy_read_status,
>> - .ack_interrupt = bcm63xx_ack_interrupt,
>> - .config_intr = bcm63xx_config_intr,
>> + .ack_interrupt = bcm_phy_ack_intr,
>> + .config_intr = bcm_phy_config_intr,
>> .driver = { .owner = THIS_MODULE },
>> }, {
>> /* same phy as above, with just a different OUI */
>> @@ -95,8 +67,8 @@ static struct phy_driver bcm63xx_driver[] = {
>> .config_init = bcm63xx_config_init,
>> .config_aneg = genphy_config_aneg,
>> .read_status = genphy_read_status,
>> - .ack_interrupt = bcm63xx_ack_interrupt,
>> - .config_intr = bcm63xx_config_intr,
>> + .ack_interrupt = bcm_phy_ack_intr,
>> + .config_intr = bcm_phy_config_intr,
>> .driver = { .owner = THIS_MODULE },
>> } };
>> diff --git a/drivers/net/phy/bcm7xxx.c b/drivers/net/phy/bcm7xxx.c
>> index 6b701b3..efa31a6 100644
>> --- a/drivers/net/phy/bcm7xxx.c
>> +++ b/drivers/net/phy/bcm7xxx.c
>> @@ -12,12 +12,12 @@
>> #include <linux/module.h>
>> #include <linux/phy.h>
>> #include <linux/delay.h>
>> +#include "bcm-phy-lib.h"
>> #include <linux/bitops.h>
>> #include <linux/brcmphy.h>
>> #include <linux/mdio.h>
>> /* Broadcom BCM7xxx internal PHY registers */
>> -#define MII_BCM7XXX_CHANNEL_WIDTH 0x2000
>> /* 40nm only register definitions */
>> #define MII_BCM7XXX_100TX_AUX_CTL 0x10
>> @@ -48,37 +48,13 @@
>> #define CORE_EXPB0 0xb0
>> -static void phy_write_exp(struct phy_device *phydev,
>> - u16 reg, u16 value)
>> -{
>> - phy_write(phydev, MII_BCM54XX_EXP_SEL, MII_BCM54XX_EXP_SEL_ER |
>> reg);
>> - phy_write(phydev, MII_BCM54XX_EXP_DATA, value);
>> -}
>> -
>> -static void phy_write_misc(struct phy_device *phydev,
>> - u16 reg, u16 chl, u16 value)
>> -{
>> - int tmp;
>> -
>> - phy_write(phydev, MII_BCM54XX_AUX_CTL,
>> MII_BCM54XX_AUXCTL_SHDWSEL_MISC);
>> -
>> - tmp = phy_read(phydev, MII_BCM54XX_AUX_CTL);
>> - tmp |= MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA;
>> - phy_write(phydev, MII_BCM54XX_AUX_CTL, tmp);
>> -
>> - tmp = (chl * MII_BCM7XXX_CHANNEL_WIDTH) | reg;
>> - phy_write(phydev, MII_BCM54XX_EXP_SEL, tmp);
>> -
>> - phy_write(phydev, MII_BCM54XX_EXP_DATA, value);
>> -}
>> -
>> static void r_rc_cal_reset(struct phy_device *phydev)
>> {
>> /* Reset R_CAL/RC_CAL Engine */
>> - phy_write_exp(phydev, 0x00b0, 0x0010);
>> + bcm_phy_write_exp(phydev, 0x00b0, 0x0010);
>> /* Disable Reset R_AL/RC_CAL Engine */
>> - phy_write_exp(phydev, 0x00b0, 0x0000);
>> + bcm_phy_write_exp(phydev, 0x00b0, 0x0000);
>> }
>> static int bcm7xxx_28nm_b0_afe_config_init(struct phy_device *phydev)
>> @@ -86,18 +62,18 @@ static int bcm7xxx_28nm_b0_afe_config_init(struct
>> phy_device *phydev)
>> /* Increase VCO range to prevent unlocking problem of PLL at low
>> * temp
>> */
>> - phy_write_misc(phydev, PLL_PLLCTRL_1, 0x0048);
>> + bcm_phy_write_misc(phydev, PLL_PLLCTRL_1, 0x0048);
>> /* Change Ki to 011 */
>> - phy_write_misc(phydev, PLL_PLLCTRL_2, 0x021b);
>> + bcm_phy_write_misc(phydev, PLL_PLLCTRL_2, 0x021b);
>> /* Disable loading of TVCO buffer to bandgap, set bandgap trim
>> * to 111
>> */
>> - phy_write_misc(phydev, PLL_PLLCTRL_4, 0x0e20);
>> + bcm_phy_write_misc(phydev, PLL_PLLCTRL_4, 0x0e20);
>> /* Adjust bias current trim by -3 */
>> - phy_write_misc(phydev, DSP_TAP10, 0x690b);
>> + bcm_phy_write_misc(phydev, DSP_TAP10, 0x690b);
>> /* Switch to CORE_BASE1E */
>> phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0xd);
>> @@ -105,19 +81,19 @@ static int bcm7xxx_28nm_b0_afe_config_init(struct
>> phy_device *phydev)
>> r_rc_cal_reset(phydev);
>> /* write AFE_RXCONFIG_0 */
>> - phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb19);
>> + bcm_phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb19);
>> /* write AFE_RXCONFIG_1 */
>> - phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9a3f);
>> + bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9a3f);
>> /* write AFE_RX_LP_COUNTER */
>> - phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);
>> + bcm_phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);
>> /* write AFE_HPF_TRIM_OTHERS */
>> - phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x000b);
>> + bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x000b);
>> /* write AFTE_TX_CONFIG */
>> - phy_write_misc(phydev, AFE_TX_CONFIG, 0x0800);
>> + bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x0800);
>> return 0;
>> }
>> @@ -125,36 +101,36 @@ static int
>> bcm7xxx_28nm_b0_afe_config_init(struct phy_device *phydev)
>> static int bcm7xxx_28nm_d0_afe_config_init(struct phy_device *phydev)
>> {
>> /* AFE_RXCONFIG_0 */
>> - phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb15);
>> + bcm_phy_write_misc(phydev, AFE_RXCONFIG_0, 0xeb15);
>> /* AFE_RXCONFIG_1 */
>> - phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);
>> + bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);
>> /* AFE_RXCONFIG_2, set rCal offset for HT=0 code and LT=-2
>> code */
>> - phy_write_misc(phydev, AFE_RXCONFIG_2, 0x2003);
>> + bcm_phy_write_misc(phydev, AFE_RXCONFIG_2, 0x2003);
>> /* AFE_RX_LP_COUNTER, set RX bandwidth to maximum */
>> - phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);
>> + bcm_phy_write_misc(phydev, AFE_RX_LP_COUNTER, 0x7fc0);
>> /* AFE_TX_CONFIG, set 100BT Cfeed=011 to improve rise/fall
>> time */
>> - phy_write_misc(phydev, AFE_TX_CONFIG, 0x431);
>> + bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x431);
>> /* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB
>> symmetry */
>> - phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);
>> + bcm_phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);
>> /* AFE_VDAC_OTHERS_0, set 1000BT Cidac=010 for all ports */
>> - phy_write_misc(phydev, AFE_VDAC_OTHERS_0, 0xa020);
>> + bcm_phy_write_misc(phydev, AFE_VDAC_OTHERS_0, 0xa020);
>> /* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set
>> rCal
>> * offset for HT=0 code
>> */
>> - phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);
>> + bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);
>> /* CORE_BASE1E, force trim to overwrite and set I_ext trim to
>> 0000 */
>> phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0x0010);
>> /* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
>> - phy_write_misc(phydev, DSP_TAP10, 0x011b);
>> + bcm_phy_write_misc(phydev, DSP_TAP10, 0x011b);
>> /* Reset R_CAL/RC_CAL engine */
>> r_rc_cal_reset(phydev);
>> @@ -165,24 +141,24 @@ static int
>> bcm7xxx_28nm_d0_afe_config_init(struct phy_device *phydev)
>> static int bcm7xxx_28nm_e0_plus_afe_config_init(struct phy_device
>> *phydev)
>> {
>> /* AFE_RXCONFIG_1, provide more margin for INL/DNL measurement */
>> - phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);
>> + bcm_phy_write_misc(phydev, AFE_RXCONFIG_1, 0x9b2f);
>> /* AFE_TX_CONFIG, set 100BT Cfeed=011 to improve rise/fall
>> time */
>> - phy_write_misc(phydev, AFE_TX_CONFIG, 0x431);
>> + bcm_phy_write_misc(phydev, AFE_TX_CONFIG, 0x431);
>> /* AFE_VDCA_ICTRL_0, set Iq=1101 instead of 0111 for AB
>> symmetry */
>> - phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);
>> + bcm_phy_write_misc(phydev, AFE_VDCA_ICTRL_0, 0xa7da);
>> /* AFE_HPF_TRIM_OTHERS, set 100Tx/10BT to -4.5% swing and set
>> rCal
>> * offset for HT=0 code
>> */
>> - phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);
>> + bcm_phy_write_misc(phydev, AFE_HPF_TRIM_OTHERS, 0x00e3);
>> /* CORE_BASE1E, force trim to overwrite and set I_ext trim to
>> 0000 */
>> phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0x0010);
>> /* DSP_TAP10, adjust bias current trim (+0% swing, +0 tick) */
>> - phy_write_misc(phydev, DSP_TAP10, 0x011b);
>> + bcm_phy_write_misc(phydev, DSP_TAP10, 0x011b);
>> /* Reset R_CAL/RC_CAL engine */
>> r_rc_cal_reset(phydev);
>> @@ -190,53 +166,6 @@ static int
>> bcm7xxx_28nm_e0_plus_afe_config_init(struct phy_device *phydev)
>> return 0;
>> }
>> -static int bcm7xxx_apd_enable(struct phy_device *phydev)
>> -{
>> - int val;
>> -
>> - /* Enable powering down of the DLL during auto-power down */
>> - val = bcm54xx_shadow_read(phydev, BCM54XX_SHD_SCR3);
>> - if (val < 0)
>> - return val;
>> -
>> - val |= BCM54XX_SHD_SCR3_DLLAPD_DIS;
>> - bcm54xx_shadow_write(phydev, BCM54XX_SHD_SCR3, val);
>> -
>> - /* Enable auto-power down */
>> - val = bcm54xx_shadow_read(phydev, BCM54XX_SHD_APD);
>> - if (val < 0)
>> - return val;
>> -
>> - val |= BCM54XX_SHD_APD_EN;
>> - return bcm54xx_shadow_write(phydev, BCM54XX_SHD_APD, val);
>> -}
>> -
>> -static int bcm7xxx_eee_enable(struct phy_device *phydev)
>> -{
>> - int val;
>> -
>> - val = phy_read_mmd_indirect(phydev, BRCM_CL45VEN_EEE_CONTROL,
>> - MDIO_MMD_AN, phydev->addr);
>> - if (val < 0)
>> - return val;
>> -
>> - /* Enable general EEE feature at the PHY level */
>> - val |= LPI_FEATURE_EN | LPI_FEATURE_EN_DIG1000X;
>> -
>> - phy_write_mmd_indirect(phydev, BRCM_CL45VEN_EEE_CONTROL,
>> - MDIO_MMD_AN, phydev->addr, val);
>> -
>> - /* Advertise supported modes */
>> - val = phy_read_mmd_indirect(phydev, MDIO_AN_EEE_ADV,
>> - MDIO_MMD_AN, phydev->addr);
>> -
>> - val |= (MDIO_AN_EEE_ADV_100TX | MDIO_AN_EEE_ADV_1000T);
>> - phy_write_mmd_indirect(phydev, MDIO_AN_EEE_ADV,
>> - MDIO_MMD_AN, phydev->addr, val);
>> -
>> - return 0;
>> -}
>> -
>> static int bcm7xxx_28nm_config_init(struct phy_device *phydev)
>> {
>> u8 rev = PHY_BRCM_7XXX_REV(phydev->dev_flags);
>> @@ -273,11 +202,11 @@ static int bcm7xxx_28nm_config_init(struct
>> phy_device *phydev)
>> if (ret)
>> return ret;
>> - ret = bcm7xxx_eee_enable(phydev);
>> + ret = bcm_phy_enable_eee(phydev);
>> if (ret)
>> return ret;
>> - return bcm7xxx_apd_enable(phydev);
>> + return bcm_phy_enable_apd(phydev, true);
>> }
>> static int bcm7xxx_28nm_resume(struct phy_device *phydev)
>> diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
>> index 9c71295..07a6119 100644
>> --- a/drivers/net/phy/broadcom.c
>> +++ b/drivers/net/phy/broadcom.c
>> @@ -14,6 +14,7 @@
>> * 2 of the License, or (at your option) any later version.
>> */
>> +#include "bcm-phy-lib.h"
>> #include <linux/module.h>
>> #include <linux/phy.h>
>> #include <linux/brcmphy.h>
>> @@ -29,39 +30,6 @@ MODULE_DESCRIPTION("Broadcom PHY driver");
>> MODULE_AUTHOR("Maciej W. Rozycki");
>> MODULE_LICENSE("GPL");
>> -/* Indirect register access functions for the Expansion Registers */
>> -static int bcm54xx_exp_read(struct phy_device *phydev, u16 regnum)
>> -{
>> - int val;
>> -
>> - val = phy_write(phydev, MII_BCM54XX_EXP_SEL, regnum);
>> - if (val < 0)
>> - return val;
>> -
>> - val = phy_read(phydev, MII_BCM54XX_EXP_DATA);
>> -
>> - /* Restore default value. It's O.K. if this write fails. */
>> - phy_write(phydev, MII_BCM54XX_EXP_SEL, 0);
>> -
>> - return val;
>> -}
>> -
>> -static int bcm54xx_exp_write(struct phy_device *phydev, u16 regnum,
>> u16 val)
>> -{
>> - int ret;
>> -
>> - ret = phy_write(phydev, MII_BCM54XX_EXP_SEL, regnum);
>> - if (ret < 0)
>> - return ret;
>> -
>> - ret = phy_write(phydev, MII_BCM54XX_EXP_DATA, val);
>> -
>> - /* Restore default value. It's O.K. if this write fails. */
>> - phy_write(phydev, MII_BCM54XX_EXP_SEL, 0);
>> -
>> - return ret;
>> -}
>> -
>> static int bcm54xx_auxctl_write(struct phy_device *phydev, u16
>> regnum, u16 val)
>> {
>> return phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum | val);
>> @@ -72,28 +40,28 @@ static int bcm50610_a0_workaround(struct
>> phy_device *phydev)
>> {
>> int err;
>> - err = bcm54xx_exp_write(phydev, MII_BCM54XX_EXP_AADJ1CH0,
>> + err = bcm_phy_write_exp(phydev, MII_BCM54XX_EXP_AADJ1CH0,
>> MII_BCM54XX_EXP_AADJ1CH0_SWP_ABCD_OEN |
>> MII_BCM54XX_EXP_AADJ1CH0_SWSEL_THPF);
>> if (err < 0)
>> return err;
>> - err = bcm54xx_exp_write(phydev, MII_BCM54XX_EXP_AADJ1CH3,
>> - MII_BCM54XX_EXP_AADJ1CH3_ADCCKADJ);
>> + err = bcm_phy_write_exp(phydev, MII_BCM54XX_EXP_AADJ1CH3,
>> + MII_BCM54XX_EXP_AADJ1CH3_ADCCKADJ);
>> if (err < 0)
>> return err;
>> - err = bcm54xx_exp_write(phydev, MII_BCM54XX_EXP_EXP75,
>> + err = bcm_phy_write_exp(phydev, MII_BCM54XX_EXP_EXP75,
>> MII_BCM54XX_EXP_EXP75_VDACCTRL);
>> if (err < 0)
>> return err;
>> - err = bcm54xx_exp_write(phydev, MII_BCM54XX_EXP_EXP96,
>> + err = bcm_phy_write_exp(phydev, MII_BCM54XX_EXP_EXP96,
>> MII_BCM54XX_EXP_EXP96_MYST);
>> if (err < 0)
>> return err;
>> - err = bcm54xx_exp_write(phydev, MII_BCM54XX_EXP_EXP97,
>> + err = bcm_phy_write_exp(phydev, MII_BCM54XX_EXP_EXP97,
>> MII_BCM54XX_EXP_EXP97_MYST);
>> return err;
>> @@ -114,7 +82,7 @@ static int bcm54xx_phydsp_config(struct phy_device
>> *phydev)
>> if (BRCM_PHY_MODEL(phydev) == PHY_ID_BCM50610 ||
>> BRCM_PHY_MODEL(phydev) == PHY_ID_BCM50610M) {
>> /* Clear bit 9 to fix a phy interop issue. */
>> - err = bcm54xx_exp_write(phydev, MII_BCM54XX_EXP_EXP08,
>> + err = bcm_phy_write_exp(phydev, MII_BCM54XX_EXP_EXP08,
>> MII_BCM54XX_EXP_EXP08_RJCT_2MHZ);
>> if (err < 0)
>> goto error;
>> @@ -129,12 +97,12 @@ static int bcm54xx_phydsp_config(struct
>> phy_device *phydev)
>> if (BRCM_PHY_MODEL(phydev) == PHY_ID_BCM57780) {
>> int val;
>> - val = bcm54xx_exp_read(phydev, MII_BCM54XX_EXP_EXP75);
>> + val = bcm_phy_read_exp(phydev, MII_BCM54XX_EXP_EXP75);
>> if (val < 0)
>> goto error;
>> val |= MII_BCM54XX_EXP_EXP75_CM_OSC;
>> - err = bcm54xx_exp_write(phydev, MII_BCM54XX_EXP_EXP75, val);
>> + err = bcm_phy_write_exp(phydev, MII_BCM54XX_EXP_EXP75, val);
>> }
>> error:
>> @@ -159,7 +127,7 @@ static void bcm54xx_adjust_rxrefclk(struct
>> phy_device *phydev)
>> BRCM_PHY_MODEL(phydev) != PHY_ID_BCM50610M)
>> return;
>> - val = bcm54xx_shadow_read(phydev, BCM54XX_SHD_SCR3);
>> + val = bcm_phy_read_shadow(phydev, BCM54XX_SHD_SCR3);
>> if (val < 0)
>> return;
>> @@ -190,9 +158,9 @@ static void bcm54xx_adjust_rxrefclk(struct
>> phy_device *phydev)
>> val |= BCM54XX_SHD_SCR3_TRDDAPD;
>> if (orig != val)
>> - bcm54xx_shadow_write(phydev, BCM54XX_SHD_SCR3, val);
>> + bcm_phy_write_shadow(phydev, BCM54XX_SHD_SCR3, val);
>> - val = bcm54xx_shadow_read(phydev, BCM54XX_SHD_APD);
>> + val = bcm_phy_read_shadow(phydev, BCM54XX_SHD_APD);
>> if (val < 0)
>> return;
>> @@ -204,7 +172,7 @@ static void bcm54xx_adjust_rxrefclk(struct
>> phy_device *phydev)
>> val &= ~BCM54XX_SHD_APD_EN;
>> if (orig != val)
>> - bcm54xx_shadow_write(phydev, BCM54XX_SHD_APD, val);
>> + bcm_phy_write_shadow(phydev, BCM54XX_SHD_APD, val);
>> }
>> static int bcm54xx_config_init(struct phy_device *phydev)
>> @@ -232,7 +200,7 @@ static int bcm54xx_config_init(struct phy_device
>> *phydev)
>> if ((BRCM_PHY_MODEL(phydev) == PHY_ID_BCM50610 ||
>> BRCM_PHY_MODEL(phydev) == PHY_ID_BCM50610M) &&
>> (phydev->dev_flags & PHY_BRCM_CLEAR_RGMII_MODE))
>> - bcm54xx_shadow_write(phydev, BCM54XX_SHD_RGMII_MODE, 0);
>> + bcm_phy_write_shadow(phydev, BCM54XX_SHD_RGMII_MODE, 0);
>> if ((phydev->dev_flags & PHY_BRCM_RX_REFCLK_UNUSED) ||
>> (phydev->dev_flags & PHY_BRCM_DIS_TXCRXC_NOENRGY) ||
>> @@ -254,8 +222,8 @@ static int bcm5482_config_init(struct phy_device
>> *phydev)
>> /*
>> * Enable secondary SerDes and its use as an LED source
>> */
>> - reg = bcm54xx_shadow_read(phydev, BCM5482_SHD_SSD);
>> - bcm54xx_shadow_write(phydev, BCM5482_SHD_SSD,
>> + reg = bcm_phy_read_shadow(phydev, BCM5482_SHD_SSD);
>> + bcm_phy_write_shadow(phydev, BCM5482_SHD_SSD,
>> reg |
>> BCM5482_SHD_SSD_LEDM |
>> BCM5482_SHD_SSD_EN);
>> @@ -264,10 +232,10 @@ static int bcm5482_config_init(struct phy_device
>> *phydev)
>> * Enable SGMII slave mode and auto-detection
>> */
>> reg = BCM5482_SSD_SGMII_SLAVE | MII_BCM54XX_EXP_SEL_SSD;
>> - err = bcm54xx_exp_read(phydev, reg);
>> + err = bcm_phy_read_exp(phydev, reg);
>> if (err < 0)
>> return err;
>> - err = bcm54xx_exp_write(phydev, reg, err |
>> + err = bcm_phy_write_exp(phydev, reg, err |
>> BCM5482_SSD_SGMII_SLAVE_EN |
>> BCM5482_SSD_SGMII_SLAVE_AD);
>> if (err < 0)
>> @@ -277,10 +245,10 @@ static int bcm5482_config_init(struct phy_device
>> *phydev)
>> * Disable secondary SerDes powerdown
>> */
>> reg = BCM5482_SSD_1000BX_CTL | MII_BCM54XX_EXP_SEL_SSD;
>> - err = bcm54xx_exp_read(phydev, reg);
>> + err = bcm_phy_read_exp(phydev, reg);
>> if (err < 0)
>> return err;
>> - err = bcm54xx_exp_write(phydev, reg,
>> + err = bcm_phy_write_exp(phydev, reg,
>> err & ~BCM5482_SSD_1000BX_CTL_PWRDOWN);
>> if (err < 0)
>> return err;
>> @@ -288,15 +256,15 @@ static int bcm5482_config_init(struct phy_device
>> *phydev)
>> /*
>> * Select 1000BASE-X register set (primary SerDes)
>> */
>> - reg = bcm54xx_shadow_read(phydev, BCM5482_SHD_MODE);
>> - bcm54xx_shadow_write(phydev, BCM5482_SHD_MODE,
>> + reg = bcm_phy_read_shadow(phydev, BCM5482_SHD_MODE);
>> + bcm_phy_write_shadow(phydev, BCM5482_SHD_MODE,
>> reg | BCM5482_SHD_MODE_1000BX);
>> /*
>> * LED1=ACTIVITYLED, LED3=LINKSPD[2]
>> * (Use LED1 as secondary SerDes ACTIVITY LED)
>> */
>> - bcm54xx_shadow_write(phydev, BCM5482_SHD_LEDS1,
>> + bcm_phy_write_shadow(phydev, BCM5482_SHD_LEDS1,
>> BCM5482_SHD_LEDS1_LED1(BCM_LED_SRC_ACTIVITYLED) |
>> BCM5482_SHD_LEDS1_LED3(BCM_LED_SRC_LINKSPD2));
>> @@ -334,35 +302,6 @@ static int bcm5482_read_status(struct
>> phy_device *phydev)
>> return err;
>> }
>> -static int bcm54xx_ack_interrupt(struct phy_device *phydev)
>> -{
>> - int reg;
>> -
>> - /* Clear pending interrupts. */
>> - reg = phy_read(phydev, MII_BCM54XX_ISR);
>> - if (reg < 0)
>> - return reg;
>> -
>> - return 0;
>> -}
>> -
>> -static int bcm54xx_config_intr(struct phy_device *phydev)
>> -{
>> - int reg, err;
>> -
>> - reg = phy_read(phydev, MII_BCM54XX_ECR);
>> - if (reg < 0)
>> - return reg;
>> -
>> - if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
>> - reg &= ~MII_BCM54XX_ECR_IM;
>> - else
>> - reg |= MII_BCM54XX_ECR_IM;
>> -
>> - err = phy_write(phydev, MII_BCM54XX_ECR, reg);
>> - return err;
>> -}
>> -
>> static int bcm5481_config_aneg(struct phy_device *phydev)
>> {
>> int ret;
>> @@ -519,8 +458,8 @@ static struct phy_driver broadcom_drivers[] = {
>> .config_init = bcm54xx_config_init,
>> .config_aneg = genphy_config_aneg,
>> .read_status = genphy_read_status,
>> - .ack_interrupt = bcm54xx_ack_interrupt,
>> - .config_intr = bcm54xx_config_intr,
>> + .ack_interrupt = bcm_phy_ack_intr,
>> + .config_intr = bcm_phy_config_intr,
>> .driver = { .owner = THIS_MODULE },
>> }, {
>> .phy_id = PHY_ID_BCM5421,
>> @@ -532,8 +471,8 @@ static struct phy_driver broadcom_drivers[] = {
>> .config_init = bcm54xx_config_init,
>> .config_aneg = genphy_config_aneg,
>> .read_status = genphy_read_status,
>> - .ack_interrupt = bcm54xx_ack_interrupt,
>> - .config_intr = bcm54xx_config_intr,
>> + .ack_interrupt = bcm_phy_ack_intr,
>> + .config_intr = bcm_phy_config_intr,
>> .driver = { .owner = THIS_MODULE },
>> }, {
>> .phy_id = PHY_ID_BCM5461,
>> @@ -545,8 +484,8 @@ static struct phy_driver broadcom_drivers[] = {
>> .config_init = bcm54xx_config_init,
>> .config_aneg = genphy_config_aneg,
>> .read_status = genphy_read_status,
>> - .ack_interrupt = bcm54xx_ack_interrupt,
>> - .config_intr = bcm54xx_config_intr,
>> + .ack_interrupt = bcm_phy_ack_intr,
>> + .config_intr = bcm_phy_config_intr,
>> .driver = { .owner = THIS_MODULE },
>> }, {
>> .phy_id = PHY_ID_BCM54616S,
>> @@ -558,8 +497,8 @@ static struct phy_driver broadcom_drivers[] = {
>> .config_init = bcm54xx_config_init,
>> .config_aneg = genphy_config_aneg,
>> .read_status = genphy_read_status,
>> - .ack_interrupt = bcm54xx_ack_interrupt,
>> - .config_intr = bcm54xx_config_intr,
>> + .ack_interrupt = bcm_phy_ack_intr,
>> + .config_intr = bcm_phy_config_intr,
>> .driver = { .owner = THIS_MODULE },
>> }, {
>> .phy_id = PHY_ID_BCM5464,
>> @@ -571,8 +510,8 @@ static struct phy_driver broadcom_drivers[] = {
>> .config_init = bcm54xx_config_init,
>> .config_aneg = genphy_config_aneg,
>> .read_status = genphy_read_status,
>> - .ack_interrupt = bcm54xx_ack_interrupt,
>> - .config_intr = bcm54xx_config_intr,
>> + .ack_interrupt = bcm_phy_ack_intr,
>> + .config_intr = bcm_phy_config_intr,
>> .driver = { .owner = THIS_MODULE },
>> }, {
>> .phy_id = PHY_ID_BCM5481,
>> @@ -584,8 +523,8 @@ static struct phy_driver broadcom_drivers[] = {
>> .config_init = bcm54xx_config_init,
>> .config_aneg = bcm5481_config_aneg,
>> .read_status = genphy_read_status,
>> - .ack_interrupt = bcm54xx_ack_interrupt,
>> - .config_intr = bcm54xx_config_intr,
>> + .ack_interrupt = bcm_phy_ack_intr,
>> + .config_intr = bcm_phy_config_intr,
>> .driver = { .owner = THIS_MODULE },
>> }, {
>> .phy_id = PHY_ID_BCM5482,
>> @@ -597,8 +536,8 @@ static struct phy_driver broadcom_drivers[] = {
>> .config_init = bcm5482_config_init,
>> .config_aneg = genphy_config_aneg,
>> .read_status = bcm5482_read_status,
>> - .ack_interrupt = bcm54xx_ack_interrupt,
>> - .config_intr = bcm54xx_config_intr,
>> + .ack_interrupt = bcm_phy_ack_intr,
>> + .config_intr = bcm_phy_config_intr,
>> .driver = { .owner = THIS_MODULE },
>> }, {
>> .phy_id = PHY_ID_BCM50610,
>> @@ -610,8 +549,8 @@ static struct phy_driver broadcom_drivers[] = {
>> .config_init = bcm54xx_config_init,
>> .config_aneg = genphy_config_aneg,
>> .read_status = genphy_read_status,
>> - .ack_interrupt = bcm54xx_ack_interrupt,
>> - .config_intr = bcm54xx_config_intr,
>> + .ack_interrupt = bcm_phy_ack_intr,
>> + .config_intr = bcm_phy_config_intr,
>> .driver = { .owner = THIS_MODULE },
>> }, {
>> .phy_id = PHY_ID_BCM50610M,
>> @@ -623,8 +562,8 @@ static struct phy_driver broadcom_drivers[] = {
>> .config_init = bcm54xx_config_init,
>> .config_aneg = genphy_config_aneg,
>> .read_status = genphy_read_status,
>> - .ack_interrupt = bcm54xx_ack_interrupt,
>> - .config_intr = bcm54xx_config_intr,
>> + .ack_interrupt = bcm_phy_ack_intr,
>> + .config_intr = bcm_phy_config_intr,
>> .driver = { .owner = THIS_MODULE },
>> }, {
>> .phy_id = PHY_ID_BCM57780,
>> @@ -636,8 +575,8 @@ static struct phy_driver broadcom_drivers[] = {
>> .config_init = bcm54xx_config_init,
>> .config_aneg = genphy_config_aneg,
>> .read_status = genphy_read_status,
>> - .ack_interrupt = bcm54xx_ack_interrupt,
>> - .config_intr = bcm54xx_config_intr,
>> + .ack_interrupt = bcm_phy_ack_intr,
>> + .config_intr = bcm_phy_config_intr,
>> .driver = { .owner = THIS_MODULE },
>> }, {
>> .phy_id = PHY_ID_BCMAC131,
>> diff --git a/include/linux/brcmphy.h b/include/linux/brcmphy.h
>> index 697ca77..6a53ab9 100644
>> --- a/include/linux/brcmphy.h
>> +++ b/include/linux/brcmphy.h
>> @@ -138,7 +138,10 @@
>> /* 01010: Auto Power-Down */
>> #define BCM54XX_SHD_APD 0x0a
>> +#define BCM_APD_CLR_MASK 0xFE9F /* clear bits 5, 6 & 8 */
>> #define BCM54XX_SHD_APD_EN 0x0020
>> +#define BCM_NO_ANEG_APD_EN 0x0060 /* bits 5 & 6 */
>> +#define BCM_APD_SINGLELP_EN 0x0100 /* Bit 8 */
>> #define BCM5482_SHD_LEDS1 0x0d /* 01101: LED Selector 1 */
>> /* LED3 / ~LINKSPD[2] selector */
>> @@ -209,25 +212,6 @@
>> #define MII_BRCM_FET_SHDW_AUXSTAT2 0x1b /* Auxiliary status 2 */
>> #define MII_BRCM_FET_SHDW_AS2_APDE 0x0020 /* Auto power down
>> enable */
>> -/*
>> - * Indirect register access functions for the
>> 1000BASE-T/100BASE-TX/10BASE-T
>> - * 0x1c shadow registers.
>> - */
>> -static inline int bcm54xx_shadow_read(struct phy_device *phydev, u16
>> shadow)
>> -{
>> - phy_write(phydev, MII_BCM54XX_SHD, MII_BCM54XX_SHD_VAL(shadow));
>> - return MII_BCM54XX_SHD_DATA(phy_read(phydev, MII_BCM54XX_SHD));
>> -}
>> -
>> -static inline int bcm54xx_shadow_write(struct phy_device *phydev, u16
>> shadow,
>> - u16 val)
>> -{
>> - return phy_write(phydev, MII_BCM54XX_SHD,
>> - MII_BCM54XX_SHD_WRITE |
>> - MII_BCM54XX_SHD_VAL(shadow) |
>> - MII_BCM54XX_SHD_DATA(val));
>> -}
>> -
>> #define BRCM_CL45VEN_EEE_CONTROL 0x803d
>> #define LPI_FEATURE_EN 0x8000
>> #define LPI_FEATURE_EN_DIG1000X 0x4000
>
--
Florian
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/