Re: gpiod API considerations [Was: [GIT PULL] On-demand device probing]
From: Uwe Kleine-König
Date: Tue Oct 20 2015 - 03:15:06 EST
Hello,
[trimming list of recipients considerably because of changed topic]
On Tue, Oct 20, 2015 at 08:47:21AM +0900, Alexandre Courbot wrote:
> On Tue, Oct 20, 2015 at 3:39 AM, Russell King - ARM Linux
> <linux@xxxxxxxxxxxxxxxx> wrote:
> > On Mon, Oct 19, 2015 at 08:27:44PM +0200, Uwe Kleine-König wrote:
> >> On Mon, Oct 19, 2015 at 04:43:24PM +0100, Russell King - ARM Linux wrote:
> >> > It's a bit ironic that you've chosen GPIO as an example there. The
> >> > "new" GPIO API (the gpiod_* stuff) only has a fwnode way to get the
> >> > gpio descriptor. There's no of_* method.
> >>
> >> Without following all that fwnode discussion:
> >> gpiod_get et al. should work for you here, doesn't it? It just takes a
> >> struct device * and I'm happy with it.
> >
> > What if you don't have a struct device? I had that problem recently
> > when modifying the mvebu PCIe code. The 'struct device' node doesn't
> > contain the GPIOs, it's the PCIe controller. Individual ports on the
> > controller are described in DT as sub-nodes, and the sub-nodes can
> > have a GPIO for card reset purposes. These sub-nodes don't have a
> > struct device.
> >
> > Right now, I'm having to do this to work around this issue:
> >
> > reset_gpio = of_get_named_gpio_flags(child, "reset-gpios", 0, &flags);
> > if (reset_gpio == -EPROBE_DEFER) {
> > ret = reset_gpio;
> > goto err;
> > }
> >
> > if (gpio_is_valid(reset_gpio)) {
> > unsigned long gpio_flags;
> >
> > port->reset_name = devm_kasprintf(dev, GFP_KERNEL, "%s-reset",
> > port->name);
> > if (!port->reset_name) {
> > ret = -ENOMEM;
> > goto err;
> > }
> >
> > if (flags & OF_GPIO_ACTIVE_LOW) {
> > dev_info(dev, "%s: reset gpio is active low\n",
> > of_node_full_name(child));
> > gpio_flags = GPIOF_ACTIVE_LOW |
> > GPIOF_OUT_INIT_LOW;
> > } else {
> > gpio_flags = GPIOF_OUT_INIT_HIGH;
> > }
> >
> > ret = devm_gpio_request_one(dev, reset_gpio, gpio_flags,
> > port->reset_name);
> > if (ret) {
> > if (ret == -EPROBE_DEFER)
> > goto err;
> > goto skip;
> > }
> >
> > port->reset_gpio = gpio_to_desc(reset_gpio);
> > }
> >
> > Not nice, is it? Not nice to have that in lots of drivers either.
> >
> > However, switching to use any of_* or fwnode_* thing also carries with
> > it another problem: you can't control the name appearing in the
> > allocation, so you end up with a bunch of GPIOs requested with a "reset"
> > name - meaning you lose any identification of which port the GPIO was
> > bound to.
>
> There are a few holes in the gpiod API. I see two solutions here:
>
> 1) extend devm_get_gpiod_from_child() to take an optional name argument
> 2) add a function to explicitly change a GPIO's name
>
> 2) seems to be the most generic solution, would that do the trick?
I would prefer 1) without "optional". A third alternative is to add at
least dev_name(dev) and maybe index to the name where applicable. Also
note that gpiod_request is called with label=NULL (in
fwnode_get_named_gpiod which is used in devm_get_gpiod_from_child), so
/sys/kernel/debug/gpio doesn't even contain "reset". I only see question
marks (using v4.3-rc5).
Best regards
Uwe
--
Pengutronix e.K. | Uwe Kleine-König |
Industrial Linux Solutions | http://www.pengutronix.de/ |
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/