Re: [PATCH v4] iio: mma8452: support either of the available interrupt pins
From: Rob Herring
Date: Thu Oct 22 2015 - 14:23:20 EST
On Thu, Oct 15, 2015 at 8:10 AM, Martin Kepplinger <martink@xxxxxxxxx> wrote:
> This change is important in order for everyone to be easily able to use the
> driver for one of the supported accelerometer chips!
>
> Until now, the driver blindly assumed that the INT1 interrupt line is wired
> on a user's board. But these devices have 2 interrupt lines and can route
> their interrupt sources to one of them. Now, if "INT2" is found and matches
> i2c_client->irq, INT2 will be used.
>
> The chip's default actually is INT2, which is why probably many boards will
> have it wired and can make use of this.
>
> Of course, this also falls back to assuming INT1, so for existing users
> nothing will break. The new functionality is described in the bindings doc.
>
> Signed-off-by: Martin Kepplinger <martin.kepplinger@xxxxxxxxxxxxxxxxxxxxx>
> ---
> changelog:
> v4: use irq that matches client->irq, backwards compatible
> v3: correctly assign irq if both pins are described in DT
> v2: don't warn but normally handle if both pins are described in dts
> thanks Mark Rutland
> v1: initial post
>
> .../devicetree/bindings/iio/accel/mma8452.txt | 6 ++++++
For the binding:
Rob Herring <robh@xxxxxxxxxx>
> drivers/iio/accel/mma8452.c | 21 +++++++++++++++------
> 2 files changed, 21 insertions(+), 6 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt
> index e3c3746..3c10e85 100644
> --- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt
> +++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt
> @@ -7,13 +7,18 @@ Required properties:
> * "fsl,mma8453"
> * "fsl,mma8652"
> * "fsl,mma8653"
> +
> - reg: the I2C address of the chip
>
> Optional properties:
>
> - interrupt-parent: should be the phandle for the interrupt controller
> +
> - interrupts: interrupt mapping for GPIO IRQ
>
> + - interrupt-names: should contain "INT1" and/or "INT2", the accelerometer's
> + interrupt line in use.
> +
> Example:
>
> mma8453fc@1d {
> @@ -21,4 +26,5 @@ Example:
> reg = <0x1d>;
> interrupt-parent = <&gpio1>;
> interrupts = <5 0>;
> + interrupt-names = "INT2";
> };
> diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
> index 1eccc2d..116a6e4 100644
> --- a/drivers/iio/accel/mma8452.c
> +++ b/drivers/iio/accel/mma8452.c
> @@ -29,6 +29,7 @@
> #include <linux/iio/events.h>
> #include <linux/delay.h>
> #include <linux/of_device.h>
> +#include <linux/of_irq.h>
>
> #define MMA8452_STATUS 0x00
> #define MMA8452_STATUS_DRDY (BIT(2) | BIT(1) | BIT(0))
> @@ -1130,13 +1131,21 @@ static int mma8452_probe(struct i2c_client *client,
> MMA8452_INT_FF_MT;
> int enabled_interrupts = MMA8452_INT_TRANS |
> MMA8452_INT_FF_MT;
> + int irq2;
>
> - /* Assume wired to INT1 pin */
> - ret = i2c_smbus_write_byte_data(client,
> - MMA8452_CTRL_REG5,
> - supported_interrupts);
> - if (ret < 0)
> - return ret;
> + irq2 = of_irq_get_byname(client->dev.of_node, "INT2");
> +
> + if (irq2 == client->irq) {
> + dev_dbg(&client->dev, "using interrupt line INT2\n");
> + } else {
> + ret = i2c_smbus_write_byte_data(client,
> + MMA8452_CTRL_REG5,
> + supported_interrupts);
> + if (ret < 0)
> + return ret;
> +
> + dev_dbg(&client->dev, "using interrupt line INT1\n");
> + }
>
> ret = i2c_smbus_write_byte_data(client,
> MMA8452_CTRL_REG4,
> --
> 2.1.4
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/