Re: [PATCH 1/3] devicetree: mfd: Add binding for the TI LM3533

[Rob Herring]

On Sun, Oct 25, 2015 at 1:09 PM, Bjorn Andersson
<bjorn.andersson@xxxxxxxxxxxxxx> wrote:
> Add the binding for the Texas Instruments LM3533 lighting power
> solution.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxxxxxx>
> ---
>  Documentation/devicetree/bindings/mfd/lm3533.txt | 183 +++++++++++++++++++++++
>  1 file changed, 183 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/lm3533.txt
>
> diff --git a/Documentation/devicetree/bindings/mfd/lm3533.txt b/Documentation/devicetree/bindings/mfd/lm3533.txt
> new file mode 100644
> index 000000000000..3cc41695a544
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/lm3533.txt
> @@ -0,0 +1,183 @@
> +Texas Instruments LM3533 binding
> +
> +This binding describes the Texas Instruments LM3533, a lighting power solution
> +for smartphone handsets. The common properties are described directly in the
> +node, while each individual component are described in an optional subnode.
> +
> +- compatible:
> +       Usage: required
> +       Value type: <stringlist>
> +       Definition: must be:
> +                   "ti,lm3533"
> +
> +- reg:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: i2c address of the LM3533 chip
> +
> +- ti,hwen-gpios:
> +       Usage: required
> +       Value type: <prop-encoded-array>
> +       Definition: reference to gpio pin connected to the HWEN input; as
> +                   specified in "gpio/gpio.txt"
> +
> +- ti,als-supply:
> +       Usage: optional
> +       Value type: <prop-encoded-array>
> +       Definition: reference to regulator powering the V_als input; as
> +                   specified in "regulator/regulator.txt"
> +
> +- ti,boost-freq:

Append "-hz".

> +       Usage: required
> +       Value type: <u32>
> +       Definition: switch-frequency of the boost converter, must be either:
> +                   500000 or 1000000
> +
> +- ti,boost-ovp:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: over voltage protection limit, must be one of: 16, 24, 32
> +                   or 40
> +
> +- #address-cells:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: must be 1
> +
> +- #size-cells:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: must be 0
> +
> += ALS SUBNODE
> +The als subnode must be named "als", it carries the als related properties.
> +
> +- ti,als-resistance:
> +       Usage: required (unless ti,pwm-mode is specified)
> +       Value type: <u32>
> +       Definition: specifies the resistor value (R_als), in Ohm. Valid values
> +                   ranges from 200kOhm to 1574Ohm.

So append "-kohm"?

> +
> +- ti,pwm-mode:
> +       Usage: optional
> +       Value type: <empty>
> +       Definition: specifies, if present, that the als should operate in pwm
> +                   mode - rather than analog mode
> +
> += BACKLIGHT NODES
> +Backlight subnodes must be named "backlight", they carry the backlight related
> +properties.
> +
> +- reg:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: specifies which of the two backlights this node corresponds
> +                   to
> +
> +- default-brightness:
> +       Usage: optional
> +       Value type: <32>
> +       Definition: specifies the default brightness for the backlight, in
> +                   units of brightness [0-255]
> +
> +- label:
> +       Usage: required
> +       Value type: <string>
> +       Definition: specifies a name of this backlight
> +
> +- led-max-microamp:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: specifies the max current for this backlight, in uA, as
> +                   described in "leds/common.txt"
> +
> +- ti,pwm-zones:
> +       Usage: optional
> +       Value type: <u32 list>
> +       Definition: lists the ALS zones to be PWM controlled for this backlight,
> +                   the values in the list are in the range [0 - 4]
> +
> += LED NODES
> +LED subnodes must be named "led", they carry the LED related properties.
> +
> +- reg:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: specifies which of the four LEDs this node corresponds to
> +
> +- linux,default-trigger:
> +       Usage: optional
> +       Value type: <string>
> +       Definition: specifies the default trigger for the LED, as described in
> +                   "leds/common.txt"
> +
> +- label:
> +       Usage: required
> +       Value type: <string>
> +       Definition: specifies a name of this LED, as described in
> +                   "leds/common.txt"
> +
> +- led-max-microamp:
> +       Usage: required
> +       Value type: <u32>
> +       Definition: specifies the max current for this LED, in uA, as described
> +                   in "leds/common.txt"
> +
> +- ti,pwm-zones:
> +       Usage: optional
> +       Value type: <u32 list>
> +       Definition: lists the ALS zones to be PWM controlled for this LED, the
> +                   values in the list are in the range [0 - 4]
> +
> += EXAMPLE
> +
> +i2c@12460000 {
> +       compatible = "qcom,i2c-qup-v1.1.1";
> +       ...
> +
> +       lm3533@36 {
> +               compatible = "ti,lm3533";
> +               reg = <0x36>;
> +
> +               ti,hwen-gpios = <&pm8921_gpio 26 GPIO_ACTIVE_HIGH>;
> +               ti,als-supply = <&pm8921_l11>;
> +
> +               ti,boost-freq = <500000>;
> +               ti,boost-ovp = <24>;
> +
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               als {
> +                       ti,als-resistance = <200000>;
> +               };
> +
> +               backlight@0 {
> +                       reg = <0>;
> +                       label = "backlight";
> +
> +                       led-max-microamp = <20200>;
> +               };
> +
> +               led@0 {
> +                       reg = <0>;
> +                       label = "red";
> +
> +                       led-max-microamp = <5000>;
> +               };
> +
> +               led@1 {
> +                       reg = <1>;
> +                       label = "green";
> +
> +                       led-max-microamp = <5000>;
> +               };
> +
> +               led@2 {
> +                       reg = <2>;
> +                       label = "blue";
> +
> +                       led-max-microamp = <5000>;
> +               };
> +       };
> +
> --
> 2.4.2
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/