Re: [RFC PATCH net-next 5/6] net: dsa: mv88e6060: add register defines header file

[Andrew Lunn]

On Mon, Nov 02, 2015 at 11:57:27AM +0100, Neil Armstrong wrote:
> To align with the mv88e6xxx code, add a similar header file
> with all the register defines.
> The file is based on the mv88e6xxx header for coherency.

Hi Neil

I did a --side-by-side diff between this and mv88e6xxx.h. I don't
think there is enough the same to allow using mv88e6xxx.c functions
with the mv88e6060 driver :-(

     Andrew

> 
> Signed-off-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
> ---
>  drivers/net/dsa/mv88e6060.h | 108 ++++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 108 insertions(+)
>  create mode 100644 drivers/net/dsa/mv88e6060.h
> 
> diff --git a/drivers/net/dsa/mv88e6060.h b/drivers/net/dsa/mv88e6060.h
> new file mode 100644
> index 0000000..ed3b3ac
> --- /dev/null
> +++ b/drivers/net/dsa/mv88e6060.h
> @@ -0,0 +1,108 @@
> +/*
> + * net/dsa/mv88e6060.h - Marvell 88e6060 switch chip support
> + * Copyright (c) 2008 Marvell Semiconductor
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + */
> +
> +#ifndef __MV88E6060_H
> +#define __MV88E6060_H
> +
> +#define MV88E6060_PORTS	6
> +
> +#define REG_PORT(p)		(0x8 + (p))
> +#define PORT_STATUS		0x00
> +#define PORT_STATUS_PAUSE_EN	BIT(15)
> +#define PORT_STATUS_MY_PAUSE	BIT(14)
> +#define PORT_STATUS_FC		(PORT_STATUS_MY_PAUSE | PORT_STATUS_PAUSE_EN)
> +#define PORT_STATUS_RESOLVED	BIT(13)
> +#define PORT_STATUS_LINK	BIT(12)
> +#define PORT_STATUS_PORTMODE	BIT(11)
> +#define PORT_STATUS_PHYMODE	BIT(10)
> +#define PORT_STATUS_DUPLEX	BIT(9)
> +#define PORT_STATUS_SPEED	BIT(8)
> +#define PORT_SWITCH_ID		0x03
> +#define PORT_SWITCH_ID_6060	0x0600
> +#define PORT_SWITCH_ID_6060_MASK	0xfff0
> +#define PORT_SWITCH_ID_6060_R1	0x0601
> +#define PORT_SWITCH_ID_6060_R2	0x0602
> +#define PORT_CONTROL		0x04
> +#define PORT_CONTROL_FORCE_FLOW_CTRL	BIT(15)
> +#define PORT_CONTROL_TRAILER	BIT(14)
> +#define PORT_CONTROL_HEADER	BIT(11)
> +#define PORT_CONTROL_INGRESS_MODE	BIT(8)
> +#define PORT_CONTROL_VLAN_TUNNEL	BIT(7)
> +#define PORT_CONTROL_STATE_MASK	0x03
> +#define PORT_CONTROL_STATE_DISABLED	0x00
> +#define PORT_CONTROL_STATE_BLOCKING	0x01
> +#define PORT_CONTROL_STATE_LEARNING	0x02
> +#define PORT_CONTROL_STATE_FORWARDING	0x03
> +#define PORT_VLAN_MAP		0x06
> +#define PORT_VLAN_MAP_DBNUM_SHIFT	12
> +#define PORT_VLAN_MAP_TABLE_MASK	0x1f
> +#define PORT_ASSOC_VECTOR	0x0b
> +#define PORT_ASSOC_VECTOR_MONITOR	BIT(15)
> +#define PORT_ASSOC_VECTOR_PAV_MASK	0x1f
> +#define PORT_RX_CNTR		0x10
> +#define PORT_TX_CNTR		0x11
> +
> +#define REG_GLOBAL		0x0f
> +#define GLOBAL_STATUS		0x00
> +#define GLOBAL_STATUS_SW_MODE_MASK	(0x3 << 12)
> +#define GLOBAL_STATUS_SW_MODE_0	(0x0 << 12)
> +#define GLOBAL_STATUS_SW_MODE_1	(0x1 << 12)
> +#define GLOBAL_STATUS_SW_MODE_2	(0x2 << 12)
> +#define GLOBAL_STATUS_SW_MODE_3	(0x3 << 12)
> +#define GLOBAL_STATUS_INIT_READY	BIT(11)
> +#define GLOBAL_STATUS_ATU_FULL		BIT(3)
> +#define GLOBAL_STATUS_ATU_DONE		BIT(2)
> +#define GLOBAL_STATUS_PHY_INT	BIT(1)
> +#define GLOBAL_STATUS_EEINT	BIT(0)
> +#define GLOBAL_MAC_01		0x01
> +#define GLOBAL_MAC_01_DIFF_ADDR	BIT(8)
> +#define GLOBAL_MAC_23		0x02
> +#define GLOBAL_MAC_45		0x03
> +#define GLOBAL_CONTROL		0x04
> +#define GLOBAL_CONTROL_DISCARD_EXCESS	BIT(13)
> +#define GLOBAL_CONTROL_MAX_FRAME_1536	BIT(10)
> +#define GLOBAL_CONTROL_RELOAD_EEPROM	BIT(9)
> +#define GLOBAL_CONTROL_CTRMODE		BIT(8)
> +#define GLOBAL_CONTROL_ATU_FULL_EN	BIT(3)
> +#define GLOBAL_CONTROL_ATU_DONE_EN	BIT(2)
> +#define GLOBAL_CONTROL_PHYINT_EN	BIT(1)
> +#define GLOBAL_CONTROL_EEPROM_DONE_EN	BIT(0)
> +#define GLOBAL_ATU_CONTROL	0x0a
> +#define GLOBAL_ATU_CONTROL_SWRESET	BIT(15)
> +#define GLOBAL_ATU_CONTROL_LEARNDIS	BIT(14)
> +#define GLOBAL_ATU_CONTROL_ATUSIZE_256	(0x0 << 12)
> +#define GLOBAL_ATU_CONTROL_ATUSIZE_512	(0x1 << 12)
> +#define GLOBAL_ATU_CONTROL_ATUSIZE_1024	(0x2 << 12)
> +#define GLOBAL_ATU_CONTROL_ATE_AGE_SHIFT	4
> +#define GLOBAL_ATU_CONTROL_ATE_AGE_MASK	(0xff << 4)
> +#define GLOBAL_ATU_CONTROL_ATE_AGE_5MIN	(0x13 << 4)
> +#define GLOBAL_ATU_OP		0x0b
> +#define GLOBAL_ATU_OP_BUSY	BIT(15)
> +#define GLOBAL_ATU_OP_NOP		(0 << 12)
> +#define GLOBAL_ATU_OP_FLUSH_ALL	((1 << 12) | GLOBAL_ATU_OP_BUSY)
> +#define GLOBAL_ATU_OP_FLUSH_UNLOCKED	((2 << 12) | GLOBAL_ATU_OP_BUSY)
> +#define GLOBAL_ATU_OP_LOAD_DB		((3 << 12) | GLOBAL_ATU_OP_BUSY)
> +#define GLOBAL_ATU_OP_GET_NEXT_DB	((4 << 12) | GLOBAL_ATU_OP_BUSY)
> +#define GLOBAL_ATU_OP_FLUSH_DB		((5 << 12) | GLOBAL_ATU_OP_BUSY)
> +#define GLOBAL_ATU_OP_FLUSH_UNLOCKED_DB ((6 << 12) | GLOBAL_ATU_OP_BUSY)
> +#define GLOBAL_ATU_DATA		0x0c
> +#define GLOBAL_ATU_DATA_PORT_VECTOR_MASK	0x3f0
> +#define GLOBAL_ATU_DATA_PORT_VECTOR_SHIFT	4
> +#define GLOBAL_ATU_DATA_STATE_MASK		0x0f
> +#define GLOBAL_ATU_DATA_STATE_UNUSED		0x00
> +#define GLOBAL_ATU_DATA_STATE_UC_STATIC		0x0e
> +#define GLOBAL_ATU_DATA_STATE_UC_LOCKED		0x0f
> +#define GLOBAL_ATU_DATA_STATE_MC_STATIC		0x07
> +#define GLOBAL_ATU_DATA_STATE_MC_LOCKED		0x0e
> +#define GLOBAL_ATU_MAC_01	0x0d
> +#define GLOBAL_ATU_MAC_23	0x0e
> +#define GLOBAL_ATU_MAC_45	0x0f
> +
> +#endif
> -- 
> 1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/