Re: [PATCH] extcon: add MAX3355 driver

[Chanwoo Choi]

Hello,

I received the reply from you after too long time (17~18day).
You better to reply it more a little more quickly
if you have the question or new patches.

On 2015ë 11ì 10ì 03:24, Sergei Shtylyov wrote:
> Hello.
> 
> On 10/23/2015 08:56 AM, Chanwoo Choi wrote:
> 
>>>>>> MAX3355E chip integrates a charge pump and comparators to enable a system with
>>>>>> an integrated USB OTG dual-role transceiver to function as a USB OTG dual-role
>>>>>> device. In addition to sensing/controlling Vbus, the chip also passes thru the
>>>>>> ID signal from the USB OTG connector.  On some Renesas boards, this signal  is
>>>>>> just  fed into the SoC thru a GPIO pin -- there's no real OTG controller, only
>>>>>> host and gadget USB controllers sharing the same USB bus; however,  we'd  like
>>>>>> to allow host or gadget drivers to be loaded depending on the cable type,
>>>>>> hence
>>>>>> the need for the MAX3355 extcon driver. The Vbus status signals are also wired
>>>>>> to GPIOs (however, we're not currently intested in them), the  OFFVBUS# signal
>>>>>> is controlled  by the host controllers, there's also the SHDN# signal wired to
>>>>>> GPIO, which should be high for normal operation.
>>>>
>>>>>> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@xxxxxxxxxxxxxxxxxx>
>>>>
>>>>>> ---
>>>>>> The patch is against the 'extcon-next' branch of the 'extcon.git' repo.
>>>>
>>>>>>    Documentation/devicetree/bindings/extcon/extcon-max3355.txt |   21 ++
>>>>>>    drivers/extcon/Kconfig                                      |    6
>>>>>>    drivers/extcon/Makefile                                     |    1
>>>>>>    drivers/extcon/extcon-max3355.c                             |  122
>>>>>> ++++++++++++
>>>>>>    4 files changed, 150 insertions(+)
>>>>
>>>>>> Index: extcon/Documentation/devicetree/bindings/extcon/extcon-max3355.txt
>>>>>> ===================================================================
>>>>>> --- /dev/null
>>>>>> +++ extcon/Documentation/devicetree/bindings/extcon/extcon-max3355.txt
>>>>>> @@ -0,0 +1,21 @@
>>>>>> +MAX3355 USB OTG chip
>>>>
>>>>> Need manufactor information as following :
>>>>>     -> Maxim MAX3355
>>>>
>>>>      Would be Maxim enough? Or perhaps I should use Maxim Integrated [Products]?
>>>
>>>     You haven't replied to my questions.
>>>
>>>>>> +--------------------
>>>>>> +
>>>>>> +MAX3355 integrates a charge pump and comparators to enable a system with an
>>>>>> +integrated USB OTG dual-role transceiver to function as a USB OTG dual-role
>>>>>> +device.
>>>>>> +
>>>>>> +Required properties:
>>>>>> +- compatible: should be "maxim,max3355";
>>>>>> +- maxim,shdn-gpio: should contain a phandle and GPIO specifier for the
>>>>>> GPIO pin
>>>>>> +  connected to the MAX3355's SHDN# pin;
>>>>>> +- maxim,id-gpio: should contain a phandle and GPIO specifier for the GPIO pin
>>>>>> +  connected to the MAX3355's ID_OUT pin.
>>>>>> +
>>>>>> +Example (Koelsch board):
>>>>>> +
>>>>>> +    usb-otg {
>>>>>> +        compatible = "maxim,max3355";
>>>>>> +        maxim,shdn-gpio = <&gpio2 4 GPIO_ACTIVE_LOW>;
>>>>>> +        maxim,id-gpio = <&gpio5 31 GPIO_ACTIVE_HIGH>;
>>>>
>>>>> Kernel already supported the gpio helper function to get gpio from devicetree.
>>>>> I prefer use follwoing style by using of_get_gpio()/of_get_gpio_flags() in
>>>>> include/linux/of_gpio.h.
>>>>
>>>>>          gpios = <&gpio2 4 GPIO_ACTIVE_LOW>, <&gpio5 31 GPIO_ACTIVE_HIGH>;
>>>>
>>>>      OK, though Documentation/devicetree/bindings/gpio/gpio.txt does not seem
>>>> to insist on using this one...
>>>
>>>     Moreover, it now says "gpios" isn't allowed for the new bindings. So I have to strongly disagree here...
>>
>> OK. But, I recommend you use the 'gpiod' with devm_gpiod_get
>> instead of using devm_gpio_request_one() directly as following:
>> You can refer drivers/extcon/extcon-usb-gpio.c about using gpiod.
>>
>> For example,
>>     data->shdn_gpiod = devm_gpiod_get(dev, "maxim,shdn", GPIOD_IN);
>>     data->id_gpiod = devm_gpiod_get(dev, "maxim,id", GPIOD_IN);
> 
>    Thanks, done now. I just had another idea: how about I add an optional "enable-gpio" property to the 'extcon-usb-gpio' driver? I wouldn't need my own driver then at all... :-)

What is meaning of 'enable-gpio' property?
You better to explain your goal about 'enable-gpio' property

Also, If you think that it is generic way about
adding 'enable-gpio' property to extcon-usb-gpio.c,
you can try it.

Thanks,
Chanwoo Choi


--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/