Re: [PATCH v3 00/12] usb: early: add support for early printk through USB3 debug port

From: Dave Young
Date: Thu Nov 12 2015 - 01:01:22 EST

Next message: Jessica Yu: "Re: samples: livepatch: init reloc list and mark as klp module"
Previous message: iSayor: "åææåäåèçääååïåçèæååäåæååéï"
In reply to: Lu, Baolu: "Re: [PATCH v3 00/12] usb: early: add support for early printk through USB3 debug port"
Next in thread: Lu, Baolu: "Re: [PATCH v3 00/12] usb: early: add support for early printk through USB3 debug port"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Hi, Baolu

On 11/12/15 at 10:45am, Lu, Baolu wrote:
> Hi Dave,
>
> Which device are you testing with? This implementation was developed
> and tested on Intel Skylake devices.
>
> It doesn't surprise me if it doesn't work with other silicons. But it do
> remind me to create a verified-list and put those known-to-work devices
> in it.
>

I have not got time to do more test. What infomation do you want?
lsusb -v?

> Thanks,
> Baolu
>
> On 11/11/2015 10:25 AM, Dave Young wrote:
> >Hi,
> >
> >On 11/11/15 at 09:32am, Lu, Baolu wrote:
> >>
> >>On 11/10/2015 05:39 PM, Dave Young wrote:
> >>>Hi,
> >>>
> >>>On 11/09/15 at 03:38pm, Lu Baolu wrote:
> >>>>This patch series adds support for early printk through USB3 debug port.
> >>>>USB3 debug port is described in xHCI specification as an optional extended
> >>>>capability.
> >>>>
> >>>I did a test with your previous patchset with the manually wired cable.
> >>>debug host detected the remote device, but later the devie automaticlly
> >>>disconnected and earlyprintk hangs.
> >>Hi Dave,
> >>
> >>What I have done is:
> >Retested it, seems it is not stable. I got a sucessful boot with earlyprintk
> >But only once and there was no "Press Y to continue", I just blindly pressed Y.
> >
> >The other tests failed.
> >
> >Since it is not convinience to test, do you have way to enable the dbc
> >after kernel boot? like echo 1 to a sysfs file to enable it.
> >>(1) Build a new kernel for debug target with this patch series applied.
> >>(2) Add "earlyprintk=xdbc" to the kernel option of debug target. The
> >> "keep" option for early printk doesn't support yet. (That's my next
> >> target.)
> >>
> >>(3) Boot the debug host, and disable USB runtime suspend:
> >>
> >># echo on > /sys/bus/pci/devices/<xhci_pci_bus_name>/power/control
> >># echo on | tee /sys/bus/usb/devices/*/power/control
> >>
> >>(4) Boot the debug target. Check the dmesg message on debug host.
> >>
> >># tail -f /var/log/kern.log
> >>
> >>Nov 12 01:27:50 allen-ult kernel: [ 1815.983374] usb 4-3: new SuperSpeed USB
> >>device number 4 using xhci_hcd
> >>Nov 12 01:27:50 allen-ult kernel: [ 1815.999595] usb 4-3: LPM exit latency
> >>is zeroed, disabling LPM.
> >>Nov 12 01:27:50 allen-ult kernel: [ 1815.999899] usb 4-3: New USB device
> >>found, idVendor=1d6b, idProduct=0004
> >>Nov 12 01:27:50 allen-ult kernel: [ 1815.999902] usb 4-3: New USB device
> >>strings: Mfr=1, Product=2, SerialNumber=3
> >>Nov 12 01:27:50 allen-ult kernel: [ 1815.999903] usb 4-3: Product: Remote
> >>GDB
> >>Nov 12 01:27:50 allen-ult kernel: [ 1815.999904] usb 4-3: Manufacturer:
> >>Linux
> >>Nov 12 01:27:50 allen-ult kernel: [ 1815.999905] usb 4-3: SerialNumber: 0001
> >>Nov 12 01:27:50 allen-ult kernel: [ 1816.000240] usb_debug 4-3:1.0: xhci_dbc
> >>converter detected
> >>Nov 12 01:27:50 allen-ult kernel: [ 1816.000360] usb 4-3: xhci_dbc converter
> >>now attached to ttyUSB0
> >>
> >>(5) Host has completed enumeration of debug device. Start "minicom" on debug
> >>host.
> >>
> >Most times I have no chance to run minicom before the usb disconnection here.
> >
> >>Welcome to minicom 2.7
> >>
> >>OPTIONS: I18n
> >>Compiled on Jan 1 2014, 17:13:19.
> >>Port /dev/ttyUSB0, 01:28:02
> >>
> >>Press CTRL-A Z for help on special keys
> >>
> >>Press Y to continue...
> >>
> >>(6) You should be able to see "Press Y to continue..." (if not, try pressing
> >>Enter key)
> >>Press Y key, debug target should go ahead with boot and early boot messages
> >>should show in mincom.
> >>
> >>Press Y to continue...
> >>[ 0.000000] Initializing cgroup subsys cpuset
> >>[ 0.000000] Initializing cgroup subsys cpu
> >>[ 0.000000] Initializing cgroup subsys cpuacct
> >>[ 0.000000] Linux version 4.3.0-rc7+ (allen@blu-skl) (gcc version 4.8.4
> >>(Ubuntu 4.8.4-2ubuntu1~14.04) 5
> >>[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.3.0-rc7+
> >>root=UUID=5a2fb856-0238-4b6e-aa45-beeccb7
> >>[ 0.000000] KERNEL supported cpus:
> >>
> >>[...skipped...]
> >>
> >>[ 0.000000] Offload RCU callbacks from CPUs: 0-7.
> >>[ 0.000000] Console: colour dummy device 80x25
> >>[ 0.000000] console [tty0] enabled
> >>[ 0.000000] bootconsole [earlyxdbc0] disabled
> >>
> >>
> >>So "the devie automaticlly disconnected and earlyprintk hangs" happens in
> >>which step?
> >>
> >Here is some log on host side.
> >
> >[ 1568.052135] usb 2-2: new SuperSpeed USB device number 5 using xhci_hcd
> >[ 1568.063416] usb 2-2: LPM exit latency is zeroed, disabling LPM.
> >[ 1568.063750] usb 2-2: New USB device found, idVendor=1d6b, idProduct=0004
> >[ 1568.063751] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
> >[ 1568.063752] usb 2-2: Product: Remote GDB
> >[ 1568.063753] usb 2-2: Manufacturer: Linux
> >[ 1568.063754] usb 2-2: SerialNumber: 0001
> >[ 1568.065580] usb_debug 2-2:1.0: xhci_dbc converter detected
> >[ 1568.066309] usb 2-2: xhci_dbc converter now attached to ttyUSB0
> >[ 1580.464706] usb 2-2: USB disconnect, device number 5
> >[ 1580.464996] xhci_dbc ttyUSB0: xhci_dbc converter now disconnected from ttyUSB0
> >[ 1580.465062] usb_debug 2-2:1.0: device disconnected
> >[ 1580.670743] usb 2-2: new SuperSpeed USB device number 6 using xhci_hcd
> >[ 1580.682068] usb 2-2: LPM exit latency is zeroed, disabling LPM.
> >[ 1580.682667] usb 2-2: New USB device found, idVendor=1d6b, idProduct=0004
> >[ 1580.682672] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
> >[ 1580.682675] usb 2-2: Product: Remote GDB
> >[ 1580.682678] usb 2-2: Manufacturer: Linux
> >[ 1580.682681] usb 2-2: SerialNumber: 0001
> >[ 1580.685190] usb_debug 2-2:1.0: xhci_dbc converter detected
> >[ 1580.687106] usb 2-2: xhci_dbc converter now attached to ttyUSB0
> >[ 1586.751477] usb 2-2: USB disconnect, device number 6
> >[ 1586.754248] xhci_dbc ttyUSB0: xhci_dbc converter now disconnected from ttyUSB0
> >[ 1586.754287] usb_debug 2-2:1.0: device disconnected
> >[ 1586.960399] usb 2-2: new SuperSpeed USB device number 7 using xhci_hcd
> >[ 1586.971562] usb 2-2: LPM exit latency is zeroed, disabling LPM.
> >[ 1586.971916] usb 2-2: New USB device found, idVendor=1d6b, idProduct=0004
> >[ 1586.971918] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
> >[ 1586.971919] usb 2-2: Product: Remote GDB
> >[ 1586.971921] usb 2-2: Manufacturer: Linux
> >[ 1586.971922] usb 2-2: SerialNumber: 0001
> >[ 1586.973140] usb_debug 2-2:1.0: xhci_dbc converter detected
> >[ 1586.973939] usb 2-2: xhci_dbc converter now attached to ttyUSB0
> >[ 1616.615418] usb 2-2: USB disconnect, device number 7
> >[ 1616.617865] xhci_dbc ttyUSB0: xhci_dbc converter now disconnected from ttyUSB0
> >[ 1616.617918] usb_debug 2-2:1.0: device disconnected
> >[ 1616.823351] usb 2-2: new SuperSpeed USB device number 8 using xhci_hcd
> >[ 1616.834520] usb 2-2: LPM exit latency is zeroed, disabling LPM.
> >[ 1616.834856] usb 2-2: New USB device found, idVendor=1d6b, idProduct=0004
> >[ 1616.834858] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
> >[ 1616.834859] usb 2-2: Product: Remote GDB
> >[ 1616.834860] usb 2-2: Manufacturer: Linux
> >[ 1616.834860] usb 2-2: SerialNumber: 0001
> >[ 1616.836715] usb_debug 2-2:1.0: xhci_dbc converter detected
> >[ 1616.837327] usb 2-2: xhci_dbc converter now attached to ttyUSB0
> >[ 1622.719311] usb 2-2: USB disconnect, device number 8
> >[ 1622.721962] xhci_dbc ttyUSB0: xhci_dbc converter now disconnected from ttyUSB0
> >[ 1622.721995] usb_debug 2-2:1.0: device disconnected
> >[ 1622.928226] usb 2-2: new SuperSpeed USB device number 9 using xhci_hcd
> >[ 1622.939383] usb 2-2: LPM exit latency is zeroed, disabling LPM.
> >[ 1622.939714] usb 2-2: New USB device found, idVendor=1d6b, idProduct=0004
> >[ 1622.939715] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
> >[ 1622.939716] usb 2-2: Product: Remote GDB
> >[ 1622.939717] usb 2-2: Manufacturer: Linux
> >[ 1622.939718] usb 2-2: SerialNumber: 0001
> >[ 1622.941593] usb_debug 2-2:1.0: xhci_dbc converter detected
> >[ 1622.942187] usb 2-2: xhci_dbc converter now attached to ttyUSB0
> >[ 1631.312112] usb 2-2: USB disconnect, device number 9
> >[ 1631.315427] xhci_dbc ttyUSB0: xhci_dbc converter now disconnected from ttyUSB0
> >[ 1631.315465] usb_debug 2-2:1.0: device disconnected
> >[ 1631.521007] usb 2-2: new SuperSpeed USB device number 10 using xhci_hcd
> >[ 1631.532212] usb 2-2: LPM exit latency is zeroed, disabling LPM.
> >[ 1631.532544] usb 2-2: New USB device found, idVendor=1d6b, idProduct=0004
> >[ 1631.532545] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
> >[ 1631.532546] usb 2-2: Product: Remote GDB
> >[ 1631.532547] usb 2-2: Manufacturer: Linux
> >[ 1631.532548] usb 2-2: SerialNumber: 0001
> >[ 1631.534413] usb_debug 2-2:1.0: xhci_dbc converter detected
> >[ 1631.535117] usb 2-2: xhci_dbc converter now attached to ttyUSB0
> >[ 1633.252488] usb 2-2: USB disconnect, device number 10
> >[ 1633.255279] xhci_dbc ttyUSB0: xhci_dbc converter now disconnected from ttyUSB0
> >[ 1633.255314] usb_debug 2-2:1.0: device disconnected
> >[ 1633.461411] usb 2-2: new SuperSpeed USB device number 11 using xhci_hcd
> >[ 1633.472598] usb 2-2: LPM exit latency is zeroed, disabling LPM.
> >[ 1633.472932] usb 2-2: New USB device found, idVendor=1d6b, idProduct=0004
> >[ 1633.472933] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
> >[ 1633.472934] usb 2-2: Product: Remote GDB
> >[ 1633.472935] usb 2-2: Manufacturer: Linux
> >[ 1633.472936] usb 2-2: SerialNumber: 0001
> >[ 1633.473987] usb_debug 2-2:1.0: xhci_dbc converter detected
> >[ 1633.474624] usb 2-2: xhci_dbc converter now attached to ttyUSB0
> >[ 1633.900927] usb 2-2: USB disconnect, device number 11
> >[ 1633.901176] xhci_dbc ttyUSB0: xhci_dbc converter now disconnected from ttyUSB0
> >[ 1633.901226] usb_debug 2-2:1.0: device disconnected
> >[ 1634.106831] usb 2-2: new SuperSpeed USB device number 12 using xhci_hcd
> >[ 1634.117987] usb 2-2: LPM exit latency is zeroed, disabling LPM.
> >[ 1634.118328] usb 2-2: New USB device found, idVendor=1d6b, idProduct=0004
> >[ 1634.118329] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
> >[ 1634.118330] usb 2-2: Product: Remote GDB
> >[ 1634.118331] usb 2-2: Manufacturer: Linux
> >[ 1634.118332] usb 2-2: SerialNumber: 0001
> >[ 1634.120194] usb_debug 2-2:1.0: xhci_dbc converter detected
> >[ 1634.120949] usb 2-2: xhci_dbc converter now attached to ttyUSB0
> >
> >Thanks
> >Dave
> >--
> >To unsubscribe from this list: send the line "unsubscribe linux-usb" in
> >the body of a message to majordomo@xxxxxxxxxxxxxxx
> >More majordomo info at http://vger.kernel.org/majordomo-info.html
> >
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Next message: Jessica Yu: "Re: samples: livepatch: init reloc list and mark as klp module"
Previous message: iSayor: "åææåäåèçääååïåçèæååäåæååéï"
In reply to: Lu, Baolu: "Re: [PATCH v3 00/12] usb: early: add support for early printk through USB3 debug port"
Next in thread: Lu, Baolu: "Re: [PATCH v3 00/12] usb: early: add support for early printk through USB3 debug port"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]