Re: [PATCH v3 2/5] tty: Introduce SER_RS485_SOFTWARE read-only flag for struct serial_rs485
From: Matwey V. Kornilov
Date: Tue Nov 17 2015 - 03:21:16 EST
2015-11-16 22:18 GMT+03:00 Peter Hurley <peter@xxxxxxxxxxxxxxxxxx>:
> On 11/14/2015 10:25 AM, One Thousand Gnomes wrote:
>>> I specifically asked for it.
>>> I can think of 2 reasons that userspace wants to know:
>>> 1. Because the characteristics of the software emulation are unacceptable so
>>> the application wants to terminate w/error rather than continue.
>> But that could equally be true of hardware.
> I had this exact same thought, but concluded that it argues for a way
> to select the software implementation even when h/w supports RS485.
>> In fact your software
>> emulation is going to behave vastly better than many of the hardware ones.
>>> 2. Because userspace will use different values for h/w vs. s/w. For example,
>>> right now, the emulation will raise/lower RTS prematurely when tx ends if
>>> the rts-after-send timer is 0.
>> That's a bug then. It should be fixed as part of the merge or future
>> patches - if they are not providing that emulation then they ought to do
>> so and at least adjust the timing based on the baud rate so you don't
>> have to spin polling the 16x50 uart to check the last bit fell out of the
> I suppose the timer(s) could be fudged and then TEMT polled (or polled every
> char baud cycles). But I don't see how this will behave better than a h/w
> implementation; the granularity of the jiffy clock alone will guarantee
> sub-optimal turnaround, even at 9600.
>> I'd have no problem with an API that was about asking what features are
>> available : both hardware and software - but the software flag seems to
>> make no sense at all. Software doesn't imply anything about quality or
>> feature set. If there is something the emulation cannot support then
>> there should be a flag indicating that feature is not supported, not a
>> flag saying software (which means nothing - as it may be supported in
>> future, or may differ by uart etc).
> Fair enough.
>> It's also not "easy to drop". If it ever goes in we are stuck with a
>> pointless impossible to correctly set flag for all eternity.
>> Please explain the correct setting for this flag when a device driver
>> uses hardware or software or a mix according to what the silicon is
>> capable of and what values are requested ? How will an application use the
>> flag meaningfully. Please explain what will happen if someone discovers a
>> silicon bug and in a future 4.x release turns an implementation from
>> hardware to software - will they have to lie about the flag to avoid
>> breaking their application code - that strikes me as a bad thing.
> The existing driver behavior is already significantly variant and needs
> to be converged, which shouldn't be too difficult. Here's a quick summary:
> mcfuart ignores delay values, delays unsupported
> imx clamps delay values to 0, delays unsupported
> atmel only delay_rts_after_send used; delay_rts_before_send does nothing
> 8250_fintek clamps delay values to 1, unclear if h/w delay is msecs
> omap-serial* software emulation (but tx empty polling not reqd)
> lpc18xx-uart clamps delay_rts_before_send to 0, unsupported
> clamps delay_rts_after_send to max h/w value
> max310x returns -ERANGE if either delay value > h/w support (15 msecs)
> sc16is7xx* returns -EINVAL if delay_rts_after_send is set
> crisv10* clamps delay_rts_before_send to 1000 msecs
> ignores delays_rts_after_send (after dma is delayed by 2 * chars)
> * implements delay(s) in software
> The omap-serial emulation should not have been merged in its current form.
> IMO the proper driver behavior should be clamp to h/w limit so an application
> can determine the maximum delay supported. If a delay is unsupported, it should
> be clamped to 0. The application should check the RS485 settings returned by
> TIOCSRS485 to determine how the driver set them.
> [ Documentation/serial/serial-rs485.txt should suggest/model this action ]
But the similar could be true for minimal supported delay.
If user requires delay which is less than lower bound, the delay is
raised to the lower bound.
If user requires delay which is greater than upper bound, the delay is
set to the upper bound.
Then software implementation could use (tx fifo size / baudrate) as
lower bound for delay_after_send.
> Are TIOCGRS485 and TIOCSRS485 documented in tty_ioctl man page? (I haven't
> updated my man pages in a while)
> As far as software vs. hardware and a query api, what I care about is
> conveying to userspace whether the implementation will be adequate for purpose,
> with the main issue being the true delay from actual EOT to RTS toggle
> when delay_after_rts_send == 0.
Or I just can internally add (tx fifo size / baudrate) to the user
supplied value to take care of the bytes in tx fifo.
> Since that delay is unbounded with software methods, I thought it made sense to
> indicate that with a read-only bit. Naming it something else is fine too;
> A more comprehensive approach might be to add a capabilities word
> to struct serial_rs485 which would allow the driver to report what
> it supports; eg. realtime turnaround or not, etc. (Not sure if extending
> struct serial_rs485 is really possible; the serial core hasn't been
> clearing padding on the driver's behalf).
>> At the very least the above should be clearly explained in the
>> documentation and patch covering notes - and if nobody can explain those
>> then IMHO the flag is broken.
> Peter Hurley
With best regards,
Matwey V. Kornilov.
Sternberg Astronomical Institute, Lomonosov Moscow State University, Russia
119991, Moscow, Universitetsky pr-k 13, +7 (495) 9392382
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/