Re: [PATCH v5 5/5] ARM: dts: TS-4800: add basic device tree

From: Shawn Guo
Date: Wed Nov 25 2015 - 01:14:35 EST

On Tue, Nov 24, 2015 at 01:00:53PM -0500, Damien Riegel wrote:
> This device tree adds support for TS-4800 by Technologic Systems. This
> board is based on MX51-babbage, but there are some subtle differences in
> the pins used, and there is an additional FPGA that is memory-mapped.
>
> More details here:
> http://wiki.embeddedarm.com/wiki/TS-4800
>
> Signed-off-by: Damien Riegel <damien.riegel@xxxxxxxxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/arm/technologic.txt | 6 +

Please put binding doc into a separate patch, and have device tree
maintainers and list on copy of that patch.

> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/imx51-ts4800.dts | 190 +++++++++++++++++++++
> 3 files changed, 198 insertions(+), 1 deletion(-)
> create mode 100644 Documentation/devicetree/bindings/arm/technologic.txt
> create mode 100644 arch/arm/boot/dts/imx51-ts4800.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/technologic.txt b/Documentation/devicetree/bindings/arm/technologic.txt
> new file mode 100644
> index 0000000..8422988
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/technologic.txt
> @@ -0,0 +1,6 @@
> +Technologic Systems Platforms Device Tree Bindings
> +--------------------------------------------------
> +
> +TS-4800 board
> +Required root node properties:
> + - compatible = "technologic,imx51-ts4800", "fsl,imx51";
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index bb8fa02..41b9985 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -258,7 +258,8 @@ dtb-$(CONFIG_SOC_IMX51) += \
> imx51-apf51dev.dtb \
> imx51-babbage.dtb \
> imx51-digi-connectcore-jsk.dtb \
> - imx51-eukrea-mbimxsd51-baseboard.dtb
> + imx51-eukrea-mbimxsd51-baseboard.dtb \
> + imx51-ts4800.dtb
> dtb-$(CONFIG_SOC_IMX53) += \
> imx53-ard.dtb \
> imx53-m53evk.dtb \
> diff --git a/arch/arm/boot/dts/imx51-ts4800.dts b/arch/arm/boot/dts/imx51-ts4800.dts
> new file mode 100644
> index 0000000..fac2058
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx51-ts4800.dts
> @@ -0,0 +1,190 @@
> +/*
> + * Copyright 2015 Savoir-faire Linux
> + *
> + * This device tree is based on imx51-babbage.dts
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +
> +/dts-v1/;
> +#include "imx51.dtsi"
> +
> +/ {
> + model = "Technologic Systems TS-4800";
> + compatible = "technologic,imx51-ts4800", "fsl,imx51";
> +
> + chosen {
> + stdout-path = &uart1;
> + };
> +
> + memory {
> + reg = <0x90000000 0x10000000>;
> + };
> +
> + soc {
> + fpga {

For node with 'reg' property, it should be named in form of
name@unit-adderss.

> + compatible = "simple-bus";
> + reg = <0xb0000000 0x1d000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + syscon: syscon@b0010000 {
> + compatible = "syscon", "simple-mfd";
> + reg = <0xb0010000 0x3d>;
> + bus-width = <16>;
> +
> + wdt@e {
> + compatible = "technologic,ts4800-wdt";
> + syscon = <&syscon 0xe>;
> + };
> + };
> + };
> + };
> +
> + clocks {
> + ckih1 {
> + clock-frequency = <22579200>;
> + };
> +
> + ckih2 {
> + clock-frequency = <24576000>;
> + };
> + };
> +};
> +
> +&esdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_esdhc1>;
> + cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
> + wp-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec>;
> + phy-mode = "mii";
> + phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
> + phy-reset-duration = <1>;
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +
> + rtc: m41t00@68 {
> + compatible = "stm,m41t00";
> + reg = <0x68>;
> + };
> +};

We generally sort device nodes alphabetically expect pin controller.
That said, &i2c2 should be put after &fec.

> +
> +
> +&iomuxc {
> + imx51-ts4800 {

With commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without function
nodes) in place, we should be able to save this level of node.

Shawn

> +
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX51_PAD_CSPI1_MISO__ECSPI1_MISO 0x185
> + MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI 0x185
> + MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK 0x185
> + MX51_PAD_CSPI1_SS0__GPIO4_24 0x85 /* CS0 */
> + >;
> + };
> +
> + pinctrl_esdhc1: esdhc1grp {
> + fsl,pins = <
> + MX51_PAD_SD1_CMD__SD1_CMD 0x400020d5
> + MX51_PAD_SD1_CLK__SD1_CLK 0x20d5
> + MX51_PAD_SD1_DATA0__SD1_DATA0 0x20d5
> + MX51_PAD_SD1_DATA1__SD1_DATA1 0x20d5
> + MX51_PAD_SD1_DATA2__SD1_DATA2 0x20d5
> + MX51_PAD_SD1_DATA3__SD1_DATA3 0x20d5
> + MX51_PAD_GPIO1_0__GPIO1_0 0x100
> + MX51_PAD_GPIO1_1__GPIO1_1 0x100
> + >;
> + };
> +
> + pinctrl_fec: fecgrp {
> + fsl,pins = <
> + MX51_PAD_EIM_EB2__FEC_MDIO 0x000001f5
> + MX51_PAD_EIM_EB3__FEC_RDATA1 0x00000085
> + MX51_PAD_EIM_CS2__FEC_RDATA2 0x00000085
> + MX51_PAD_EIM_CS3__FEC_RDATA3 0x00000085
> + MX51_PAD_EIM_CS4__FEC_RX_ER 0x00000180
> + MX51_PAD_EIM_CS5__FEC_CRS 0x00000180
> + MX51_PAD_DISP2_DAT10__FEC_COL 0x00000180
> + MX51_PAD_DISP2_DAT11__FEC_RX_CLK 0x00000180
> + MX51_PAD_DISP2_DAT14__FEC_RDATA0 0x00002180
> + MX51_PAD_DISP2_DAT15__FEC_TDATA0 0x00002004
> + MX51_PAD_NANDF_CS2__FEC_TX_ER 0x00002004
> + MX51_PAD_DI2_PIN2__FEC_MDC 0x00002004
> + MX51_PAD_DISP2_DAT6__FEC_TDATA1 0x00002004
> + MX51_PAD_DISP2_DAT7__FEC_TDATA2 0x00002004
> + MX51_PAD_DISP2_DAT8__FEC_TDATA3 0x00002004
> + MX51_PAD_DISP2_DAT9__FEC_TX_EN 0x00002004
> + MX51_PAD_DISP2_DAT13__FEC_TX_CLK 0x00002180
> + MX51_PAD_DISP2_DAT12__FEC_RX_DV 0x000020a4
> + MX51_PAD_EIM_A20__GPIO2_14 0x00000085 /* Phy Reset */
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX51_PAD_KEY_COL4__I2C2_SCL 0x400001ed
> + MX51_PAD_KEY_COL5__I2C2_SDA 0x400001ed
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX51_PAD_UART1_RXD__UART1_RXD 0x1c5
> + MX51_PAD_UART1_TXD__UART1_TXD 0x1c5
> + MX51_PAD_UART1_RTS__UART1_RTS 0x1c5
> + MX51_PAD_UART1_CTS__UART1_CTS 0x1c5
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX51_PAD_UART2_RXD__UART2_RXD 0x1c5
> + MX51_PAD_UART2_TXD__UART2_TXD 0x1c5
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX51_PAD_EIM_D25__UART3_RXD 0x1c5
> + MX51_PAD_EIM_D26__UART3_TXD 0x1c5
> + MX51_PAD_EIM_D27__UART3_RTS 0x1c5
> + MX51_PAD_EIM_D24__UART3_CTS 0x1c5
> + >;
> + };
> +
> + };
> +};
> --
> 2.5.0
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/