[RESEND PATCH V2] regulator: pv88090: new regulator driver

From: James Ban
Date: Sun Nov 29 2015 - 20:40:01 EST


From: James Ban <James.Ban.opensource@xxxxxxxxxxx>

This is the driver for the Powerventure PV88090 BUCKs and LDOs regulator.
It communicates via an I2C bus to the device.

Signed-off-by: James Ban <James.Ban.opensource@xxxxxxxxxxx>

---
Changes since PATCH V1
- Removed owner field if calls are used which set it automatically.
- Removed unneeded semicolon.
- Removed parsing the DT manually.
- Removed setting the constraints in driver.
- Removed printing an error after parsing dt.
- Added operation for range of buck voltage.

This patch applies against linux-next and next-20151118


.../devicetree/bindings/regulator/pv88090.txt | 65 +++
drivers/regulator/Kconfig | 8 +
drivers/regulator/Makefile | 1 +
drivers/regulator/pv88090-regulator.c | 458 ++++++++++++++++++++
drivers/regulator/pv88090-regulator.h | 98 +++++
5 files changed, 630 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/pv88090.txt
create mode 100644 drivers/regulator/pv88090-regulator.c
create mode 100644 drivers/regulator/pv88090-regulator.h

diff --git a/Documentation/devicetree/bindings/regulator/pv88090.txt b/Documentation/devicetree/bindings/regulator/pv88090.txt
new file mode 100644
index 0000000..e52b2a9
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/pv88090.txt
@@ -0,0 +1,65 @@
+* Powerventure Semiconductor PV88090 Voltage Regulator
+
+Required properties:
+- compatible: "pvs,pv88090".
+- reg: I2C slave address, usually 0x48.
+- interrupts: the interrupt outputs of the controller
+- regulators: A node that houses a sub-node for each regulator within the
+ device. Each sub-node is identified using the node's name, with valid
+ values listed below. The content of each sub-node is defined by the
+ standard binding for regulators; see regulator.txt.
+ BUCK1, BUCK2, BUCK3, LDO1, and LDO2.
+
+Optional properties:
+- Any optional property defined in regulator.txt
+
+Example
+
+ pmic: pv88090@48 {
+ compatible = "pvs,pv88090";
+ reg = <0x48>;
+ interrupt-parent = <&gpio>;
+ interrupts = <24 24>;
+
+ regulators {
+ BUCK1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = < 600000>;
+ regulator-max-microvolt = <1393750>;
+ regulator-min-microamp = < 220000>;
+ regulator-max-microamp = <7040000>;
+ regulator-boot-on;
+ };
+
+ BUCK2 {
+ regulator-name = "buck2";
+ regulator-min-microvolt = < 600000>;
+ regulator-max-microvolt = <1393750>;
+ regulator-min-microamp = <1496000>;
+ regulator-max-microamp = <4189000>;
+ };
+
+ BUCK3 {
+ regulator-name = "buck3";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1393750>;
+ regulator-min-microamp = <1496000>;
+ regulator-max-microamp = <4189000>;
+ regulator-boot-on;
+ };
+
+ LDO1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <4350000>;
+ regulator-boot-on;
+ };
+
+ LDO2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = < 650000>;
+ regulator-max-microvolt = <2225000>;
+ regulator-boot-on;
+ };
+ };
+ };
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index dfdaefb..2973486 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -505,6 +505,14 @@ config REGULATOR_PFUZE100
Say y here to support the regulators found on the Freescale
PFUZE100/PFUZE200 PMIC.

+config REGULATOR_PV88090
+ tristate "Powerventure Semiconductor PV88090 regulator"
+ depends on I2C
+ select REGMAP_I2C
+ help
+ Say y here to support the voltage regulators and convertors
+ on PV88090
+
config REGULATOR_PWM
tristate "PWM voltage regulator"
depends on PWM
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 945d8ec..17cabd5 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -66,6 +66,7 @@ obj-$(CONFIG_REGULATOR_QCOM_SMD_RPM) += qcom_smd-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o
obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
+obj-$(CONFIG_REGULATOR_PV88090) += pv88090-regulator.o
obj-$(CONFIG_REGULATOR_PWM) += pwm-regulator.o
obj-$(CONFIG_REGULATOR_TPS51632) += tps51632-regulator.o
obj-$(CONFIG_REGULATOR_PBIAS) += pbias-regulator.o
diff --git a/drivers/regulator/pv88090-regulator.c b/drivers/regulator/pv88090-regulator.c
new file mode 100644
index 0000000..88d9c04
--- /dev/null
+++ b/drivers/regulator/pv88090-regulator.c
@@ -0,0 +1,458 @@
+/*
+ * pv88090-regulator.c - Regulator device driver for PV88090
+ * Copyright (C) 2015 Powerventure Semiconductor Ltd.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regmap.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/proc_fs.h>
+#include <linux/uaccess.h>
+#include "pv88090-regulator.h"
+
+#define PV88090_MAX_REGULATORS 5
+
+/* PV88090 REGULATOR IDs */
+enum {
+ /* BUCKs */
+ PV88090_ID_BUCK1,
+ PV88090_ID_BUCK2,
+ PV88090_ID_BUCK3,
+
+ /* LDOs */
+ PV88090_ID_LDO1,
+ PV88090_ID_LDO2,
+};
+
+struct pv88090_regulator {
+ struct regulator_desc desc;
+ /* Current limiting */
+ unsigned n_current_limits;
+ const int *current_limits;
+ unsigned int limit_mask;
+ unsigned int conf;
+ unsigned int conf2;
+};
+
+struct pv88090 {
+ struct device *dev;
+ struct regmap *regmap;
+ struct regulator_dev *rdev[PV88090_MAX_REGULATORS];
+};
+
+struct pv88090_buck_voltage {
+ int min_uV;
+ int max_uV;
+ int uV_step;
+};
+
+static const struct regmap_config pv88090_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+};
+
+/* Current limits array (in uA) for BUCK1, BUCK2, BUCK3.
+ * Entry indexes corresponds to register values.
+ */
+
+static const int pv88090_buck1_limits[] = {
+ 220000, 440000, 660000, 880000, 1100000, 1320000, 1540000, 1760000,
+ 1980000, 2200000, 2420000, 2640000, 2860000, 3080000, 3300000, 3520000,
+ 3740000, 3960000, 4180000, 4400000, 4620000, 4840000, 5060000, 5280000,
+ 5500000, 5720000, 5940000, 6160000, 6380000, 6600000, 6820000, 7040000
+};
+
+static const int pv88090_buck23_limits[] = {
+ 1496000, 2393000, 3291000, 4189000
+};
+
+static const struct pv88090_buck_voltage pv88090_buck_vol[3] = {
+ {
+ .min_uV = 600000,
+ .max_uV = 1393750,
+ .uV_step = 6250,
+ },
+
+ {
+ .min_uV = 1400000,
+ .max_uV = 2193750,
+ .uV_step = 6250,
+ },
+ {
+ .min_uV = 1250000,
+ .max_uV = 2837500,
+ .uV_step = 12500,
+ },
+};
+
+static unsigned int pv88090_buck_get_mode(struct regulator_dev *rdev)
+{
+ struct pv88090_regulator *info = rdev_get_drvdata(rdev);
+ unsigned int data;
+ int ret, mode = 0;
+
+ ret = regmap_read(rdev->regmap, info->conf, &data);
+ if (ret < 0)
+ return ret;
+
+ switch (data & PV88090_BUCK1_MODE_MASK) {
+ case PV88090_BUCK_MODE_SYNC:
+ mode = REGULATOR_MODE_FAST;
+ break;
+ case PV88090_BUCK_MODE_AUTO:
+ mode = REGULATOR_MODE_NORMAL;
+ break;
+ case PV88090_BUCK_MODE_SLEEP:
+ mode = REGULATOR_MODE_STANDBY;
+ break;
+ }
+
+ return mode;
+}
+
+static int pv88090_buck_set_mode(struct regulator_dev *rdev,
+ unsigned int mode)
+{
+ struct pv88090_regulator *info = rdev_get_drvdata(rdev);
+ int val = 0;
+
+ switch (mode) {
+ case REGULATOR_MODE_FAST:
+ val = PV88090_BUCK_MODE_SYNC;
+ break;
+ case REGULATOR_MODE_NORMAL:
+ val = PV88090_BUCK_MODE_AUTO;
+ break;
+ case REGULATOR_MODE_STANDBY:
+ val = PV88090_BUCK_MODE_SLEEP;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return regmap_update_bits(rdev->regmap, info->conf,
+ PV88090_BUCK1_MODE_MASK, val);
+}
+
+static int pv88090_set_current_limit(struct regulator_dev *rdev, int min,
+ int max)
+{
+ struct pv88090_regulator *info = rdev_get_drvdata(rdev);
+ int i;
+
+ /* search for closest to maximum */
+ for (i = info->n_current_limits; i >= 0; i--) {
+ if (min <= info->current_limits[i]
+ && max >= info->current_limits[i]) {
+ return regmap_update_bits(rdev->regmap,
+ info->conf,
+ info->limit_mask,
+ i << PV88090_BUCK1_ILIM_SHIFT);
+ }
+ }
+
+ return -EINVAL;
+}
+
+static int pv88090_get_current_limit(struct regulator_dev *rdev)
+{
+ struct pv88090_regulator *info = rdev_get_drvdata(rdev);
+ unsigned int data;
+ int ret;
+
+ ret = regmap_read(rdev->regmap, info->conf, &data);
+ if (ret < 0)
+ return ret;
+
+ data = (data & info->limit_mask) >> PV88090_BUCK1_ILIM_SHIFT;
+ return info->current_limits[data];
+}
+
+static struct regulator_ops pv88090_buck_ops = {
+ .get_mode = pv88090_buck_get_mode,
+ .set_mode = pv88090_buck_set_mode,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+ .set_current_limit = pv88090_set_current_limit,
+ .get_current_limit = pv88090_get_current_limit,
+};
+
+static struct regulator_ops pv88090_ldo_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+};
+
+#define PV88090_BUCK(chip, regl_name, min, step, max, limits_array) \
+{\
+ .desc = {\
+ .id = chip##_ID_##regl_name,\
+ .name = __stringify(chip##_##regl_name),\
+ .of_match = of_match_ptr(#regl_name),\
+ .regulators_node = of_match_ptr("regulators"),\
+ .type = REGULATOR_VOLTAGE,\
+ .owner = THIS_MODULE,\
+ .ops = &pv88090_buck_ops,\
+ .min_uV = min, \
+ .uV_step = step, \
+ .n_voltages = ((max) - (min))/(step) + 1, \
+ .enable_reg = PV88090_REG_##regl_name##_CONF0, \
+ .enable_mask = PV88090_##regl_name##_EN, \
+ .vsel_reg = PV88090_REG_##regl_name##_CONF0, \
+ .vsel_mask = PV88090_V##regl_name##_MASK, \
+ },\
+ .current_limits = limits_array, \
+ .n_current_limits = ARRAY_SIZE(limits_array), \
+ .limit_mask = PV88090_##regl_name##_ILIM_MASK, \
+ .conf = PV88090_REG_##regl_name##_CONF1, \
+ .conf2 = PV88090_REG_##regl_name##_CONF2, \
+}
+
+#define PV88090_LDO(chip, regl_name, min, step, max) \
+{\
+ .desc = {\
+ .id = chip##_ID_##regl_name,\
+ .name = __stringify(chip##_##regl_name),\
+ .of_match = of_match_ptr(#regl_name),\
+ .regulators_node = of_match_ptr("regulators"),\
+ .type = REGULATOR_VOLTAGE,\
+ .owner = THIS_MODULE,\
+ .ops = &pv88090_ldo_ops,\
+ .min_uV = min, \
+ .uV_step = step, \
+ .n_voltages = ((max) - (min))/(step) + 1, \
+ .enable_reg = PV88090_REG_##regl_name##_CONT, \
+ .enable_mask = PV88090_##regl_name##_EN, \
+ .vsel_reg = PV88090_REG_##regl_name##_CONT, \
+ .vsel_mask = PV88090_V##regl_name##_MASK, \
+ },\
+}
+
+static struct pv88090_regulator pv88090_regulator_info[] = {
+ PV88090_BUCK(PV88090, BUCK1, 600000, 6250, 1393750,
+ pv88090_buck1_limits),
+ PV88090_BUCK(PV88090, BUCK2, 600000, 6250, 1393750,
+ pv88090_buck23_limits),
+ PV88090_BUCK(PV88090, BUCK3, 600000, 6250, 1393750,
+ pv88090_buck23_limits),
+ PV88090_LDO(PV88090, LDO1, 1200000, 50000, 4350000),
+ PV88090_LDO(PV88090, LDO2, 650000, 25000, 2225000),
+};
+
+static irqreturn_t pv88090_irq_handler(int irq, void *data)
+{
+ struct pv88090 *chip = data;
+ int i, reg_val, err, ret = IRQ_NONE;
+
+ err = regmap_read(chip->regmap, PV88090_REG_EVENT_A, &reg_val);
+ if (err < 0)
+ goto error_i2c;
+
+ if (reg_val & PV88090_E_VDD_FLT) {
+ for (i = 0; i < PV88090_MAX_REGULATORS; i++) {
+ if (chip->rdev[i] != NULL) {
+ regulator_notifier_call_chain(chip->rdev[i],
+ REGULATOR_EVENT_UNDER_VOLTAGE,
+ NULL);
+ }
+ }
+
+ err = regmap_update_bits(chip->regmap, PV88090_REG_EVENT_A,
+ PV88090_E_VDD_FLT, PV88090_E_VDD_FLT);
+ if (err < 0)
+ goto error_i2c;
+
+ ret = IRQ_HANDLED;
+ }
+
+ if (reg_val & PV88090_E_OVER_TEMP) {
+ for (i = 0; i < PV88090_MAX_REGULATORS; i++) {
+ if (chip->rdev[i] != NULL) {
+ regulator_notifier_call_chain(chip->rdev[i],
+ REGULATOR_EVENT_OVER_TEMP,
+ NULL);
+ }
+ }
+
+ err = regmap_update_bits(chip->regmap, PV88090_REG_EVENT_A,
+ PV88090_E_OVER_TEMP, PV88090_E_OVER_TEMP);
+ if (err < 0)
+ goto error_i2c;
+
+ ret = IRQ_HANDLED;
+ }
+
+ return ret;
+
+error_i2c:
+ dev_err(chip->dev, "I2C error : %d\n", err);
+ return IRQ_NONE;
+}
+
+/*
+ * I2C driver interface functions
+ */
+static int pv88090_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ struct regulator_init_data *init_data = dev_get_platdata(&i2c->dev);
+ struct pv88090 *chip;
+ struct regulator_config config = { };
+ int error, i, ret = 0;
+ unsigned int conf2, range, index;
+
+ chip = devm_kzalloc(&i2c->dev, sizeof(struct pv88090), GFP_KERNEL);
+ if (!chip)
+ return -ENOMEM;
+
+ chip->dev = &i2c->dev;
+ chip->regmap = devm_regmap_init_i2c(i2c, &pv88090_regmap_config);
+ if (IS_ERR(chip->regmap)) {
+ error = PTR_ERR(chip->regmap);
+ dev_err(chip->dev, "Failed to allocate register map: %d\n",
+ error);
+ return error;
+ }
+
+ i2c_set_clientdata(i2c, chip);
+
+ if (i2c->irq != 0) {
+ ret = regmap_write(chip->regmap, PV88090_REG_MASK_A, 0xFF);
+ if (ret < 0) {
+ dev_err(chip->dev,
+ "Failed to mask A reg: %d\n", ret);
+ return ret;
+ }
+
+ regmap_write(chip->regmap, PV88090_REG_MASK_B, 0xFF);
+ if (ret < 0) {
+ dev_err(chip->dev,
+ "Failed to mask B reg: %d\n", ret);
+ return ret;
+ }
+
+ ret = request_threaded_irq(i2c->irq, NULL,
+ pv88090_irq_handler,
+ IRQF_TRIGGER_LOW|IRQF_ONESHOT,
+ "pv88090", chip);
+ if (ret != 0) {
+ dev_err(chip->dev, "Failed to request IRQ: %d\n",
+ i2c->irq);
+ return ret;
+ }
+
+ ret = regmap_update_bits(chip->regmap, PV88090_REG_MASK_A,
+ PV88090_M_VDD_FLT | PV88090_M_OVER_TEMP, 0);
+ if (ret < 0) {
+ dev_err(chip->dev,
+ "Failed to update mask reg: %d\n", ret);
+ return ret;
+ }
+
+ } else {
+ dev_warn(chip->dev, "No IRQ configured\n");
+ }
+
+ config.dev = chip->dev;
+ config.regmap = chip->regmap;
+
+ for (i = 0; i < PV88090_MAX_REGULATORS; i++) {
+ if (init_data)
+ config.init_data = &init_data[i];
+
+ if (i == PV88090_ID_BUCK2 || i == PV88090_ID_BUCK3) {
+ ret = regmap_read(chip->regmap,
+ pv88090_regulator_info[i].conf2, &conf2);
+ if (ret < 0)
+ return ret;
+
+ conf2 = ((conf2 >> PV88090_BUCK_VDAC_RANGE_SHIFT)
+ && PV88090_BUCK_VDAC_RANGE_MASK);
+
+ ret = regmap_read(chip->regmap,
+ PV88090_REG_BUCK_FOLD_RANGE, &range);
+ if (ret < 0)
+ return ret;
+
+ range = ((range
+ >> (PV88080_BUCK_VRANGE_GAIN_SHIFT + i - 1))
+ && PV88080_BUCK_VRANGE_GAIN_MASK);
+ index = ((range << 1) | conf2);
+
+ pv88090_regulator_info[i].desc.min_uV
+ = pv88090_buck_vol[index].min_uV;
+ pv88090_regulator_info[i].desc.uV_step
+ = pv88090_buck_vol[index].uV_step;
+ pv88090_regulator_info[i].desc.n_voltages
+ = ((pv88090_buck_vol[index].max_uV)
+ - (pv88090_buck_vol[index].min_uV))
+ /(pv88090_buck_vol[index].uV_step) + 1;
+ }
+
+ config.driver_data = (void *)&pv88090_regulator_info[i];
+ chip->rdev[i] = devm_regulator_register(chip->dev,
+ &pv88090_regulator_info[i].desc, &config);
+ if (IS_ERR(chip->rdev[i])) {
+ dev_err(chip->dev,
+ "Failed to register PV88090 regulator\n");
+ return PTR_ERR(chip->rdev[i]);
+ }
+ }
+
+ return 0;
+}
+
+static const struct i2c_device_id pv88090_i2c_id[] = {
+ {"pv88090", 0},
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, pv88090_i2c_id);
+
+#ifdef CONFIG_OF
+static const struct of_device_id pv88090_dt_ids[] = {
+ { .compatible = "pvs,pv88090", .data = &pv88090_i2c_id[0] },
+ {},
+};
+MODULE_DEVICE_TABLE(of, pv88090_dt_ids);
+#endif
+
+static struct i2c_driver pv88090_regulator_driver = {
+ .driver = {
+ .name = "pv88090",
+ .of_match_table = of_match_ptr(pv88090_dt_ids),
+ },
+ .probe = pv88090_i2c_probe,
+ .id_table = pv88090_i2c_id,
+};
+
+module_i2c_driver(pv88090_regulator_driver);
+
+MODULE_AUTHOR("James Ban <James.Ban.opensource@xxxxxxxxxxx>");
+MODULE_DESCRIPTION("Regulator device driver for Powerventure PV88090");
+MODULE_LICENSE("GPL");
diff --git a/drivers/regulator/pv88090-regulator.h b/drivers/regulator/pv88090-regulator.h
new file mode 100644
index 0000000..d7aca8d
--- /dev/null
+++ b/drivers/regulator/pv88090-regulator.h
@@ -0,0 +1,98 @@
+/*
+ * pv88090-regulator.h - Regulator definitions for PV88090
+ * Copyright (C) 2015 Powerventure Semiconductor Ltd.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __PV88090_REGISTERS_H__
+#define __PV88090_REGISTERS_H__
+
+/* System Control and Event Registers */
+#define PV88090_REG_EVENT_A 0x03
+#define PV88090_REG_MASK_A 0x06
+#define PV88090_REG_MASK_B 0x07
+
+/* Regulator Registers */
+#define PV88090_REG_BUCK1_CONF0 0x18
+#define PV88090_REG_BUCK1_CONF1 0x19
+#define PV88090_REG_BUCK1_CONF2 0x1a
+#define PV88090_REG_BUCK2_CONF0 0x1b
+#define PV88090_REG_BUCK2_CONF1 0x1c
+#define PV88090_REG_BUCK2_CONF2 0x58
+#define PV88090_REG_BUCK3_CONF0 0x1d
+#define PV88090_REG_BUCK3_CONF1 0x1e
+#define PV88090_REG_BUCK3_CONF2 0x5c
+
+#define PV88090_REG_LDO1_CONT 0x1f
+#define PV88090_REG_LDO2_CONT 0x20
+#define PV88090_REG_LDO3_CONT 0x21
+#define PV88090_REG_BUCK_FOLD_RANGE 0x61
+
+/* PV88090_REG_EVENT_A (addr=0x03) */
+#define PV88090_E_VDD_FLT 0x01
+#define PV88090_E_OVER_TEMP 0x02
+
+/* PV88090_REG_MASK_A (addr=0x06) */
+#define PV88090_M_VDD_FLT 0x01
+#define PV88090_M_OVER_TEMP 0x02
+
+/* PV88090_REG_BUCK1_CONF0 (addr=0x18) */
+#define PV88090_BUCK1_EN 0x80
+#define PV88090_VBUCK1_MASK 0x7F
+/* PV88090_REG_BUCK2_CONF0 (addr=0x1b) */
+#define PV88090_BUCK2_EN 0x80
+#define PV88090_VBUCK2_MASK 0x7F
+/* PV88090_REG_BUCK3_CONF0 (addr=0x1d) */
+#define PV88090_BUCK3_EN 0x80
+#define PV88090_VBUCK3_MASK 0x7F
+/* PV88090_REG_LDO1_CONT (addr=0x1f) */
+#define PV88090_LDO1_EN 0x40
+#define PV88090_VLDO1_MASK 0x3F
+/* PV88090_REG_LDO2_CONT (addr=0x20) */
+#define PV88090_LDO2_EN 0x40
+#define PV88090_VLDO2_MASK 0x3F
+
+/* PV88090_REG_BUCK1_CONF1 (addr=0x19) */
+#define PV88090_BUCK1_ILIM_SHIFT 2
+#define PV88090_BUCK1_ILIM_MASK 0x7C
+#define PV88090_BUCK1_MODE_MASK 0x03
+
+/* PV88090_REG_BUCK2_CONF1 (addr=0x1c) */
+#define PV88090_BUCK2_ILIM_SHIFT 2
+#define PV88090_BUCK2_ILIM_MASK 0x0C
+#define PV88090_BUCK2_MODE_MASK 0x03
+
+/* PV88090_REG_BUCK3_CONF1 (addr=0x1e) */
+#define PV88090_BUCK3_ILIM_SHIFT 2
+#define PV88090_BUCK3_ILIM_MASK 0x0C
+#define PV88090_BUCK3_MODE_MASK 0x03
+
+#define PV88090_BUCK_MODE_SLEEP 0x00
+#define PV88090_BUCK_MODE_AUTO 0x01
+#define PV88090_BUCK_MODE_SYNC 0x02
+
+/* PV88090_REG_BUCK2_CONF2 (addr=0x58) */
+/* PV88090_REG_BUCK3_CONF2 (addr=0x5c) */
+#define PV88090_BUCK_VDAC_RANGE_SHIFT 7
+#define PV88090_BUCK_VDAC_RANGE_MASK 0x01
+
+#define PV88090_BUCK_VDAC_RANGE_1 0x00
+#define PV88090_BUCK_VDAC_RANGE_2 0x01
+
+/* PV88090_REG_BUCK_FOLD_RANGE (addr=0x61) */
+#define PV88080_BUCK_VRANGE_GAIN_SHIFT 3
+#define PV88080_BUCK_VRANGE_GAIN_MASK 0x01
+
+#define PV88080_BUCK_VRANGE_GAIN_1 0x00
+#define PV88080_BUCK_VRANGE_GAIN_2 0x01
+
+#endif /* __PV88090_REGISTERS_H__ */
--
end-of-patch for PATCH V2

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/