Re: [LKP] [lkp] [x86/irq] 4c24cee6b2: IP-Config: Auto-configuration of network failed

[Borislav Petkov]

On Mon, Dec 14, 2015 at 02:54:02PM +0800, Huang, Ying wrote:
> No, there are no other systems reporting the same issue. I will queue
> more tests for make sure this is not a false positive.

I can trigger this too with my guest here.

I have these two ontop of rc5:

cc22b9b83f6a x86/irq: Enhance __assign_irq_vector() to rollback in case of failure
45dd79e03e1e x86/irq: Do not reuse struct apic_chip_data.old_domain as temporary buffer
9f9499ae8e64 Linux 4.4-rc5

and my guest stalls while booting.

The new thing I see in dmesg is this:

 ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
+..MP-BIOS bug: 8254 timer not connected to IO-APIC
+...trying to set up timer (IRQ0) through the 8259A ...
+..... (found apic 0 pin 2) ...
+....... failed.
+...trying to set up timer as Virtual Wire IRQ...
+..... failed.
+...trying to set up timer as ExtINT IRQ...
+..... works.
+APIC calibration not consistent with PM-Timer: 111ms instead of 100ms
+APIC delta adjusted to PM-Timer: 6248393 (6997337)

which leads to boot stalling and timeoutting when loading the hdd
driver:

...
[    3.973447] console [netcon0] enabled
[    3.976099] netconsole: network logging started
[    3.979604] rtc_cmos 00:00: setting system clock to 2015-12-14 10:45:35 UTC (1450089935)
[    3.985348] PM: Checking hibernation image partition /dev/sdb1
[    6.600706] usb 1-1: New USB device found, idVendor=0627, idProduct=0001
[    6.613651] usb 1-1: New USB device strings: Mfr=1, Product=3, SerialNumber=5
[    6.636905] usb 1-1: Product: QEMU USB Tablet
[    6.642248] usb 1-1: Manufacturer: QEMU
[    6.647109] usb 1-1: SerialNumber: 42
[    7.580995] ata2.00: qc timeout (cmd 0xa0)
[    7.589300] ata2.00: TEST_UNIT_READY failed (err_mask=0x5)
[    7.750715] ata2.01: NODEV after polling detection
[    7.759605] ata2.00: configured for MWDMA2
[    8.585691] input: QEMU QEMU USB Tablet as /devices/pci0000:00/0000:00:01.2/usb1/1-1/1-1:1.0/0003:0627:0001.0001/input/input1
[    8.602467] hid-generic 0003:0627:0001.0001: input,hidraw0: USB HID v0.01 Pointer [QEMU QEMU USB Tablet] on usb-0000:00:01.2-1/input0
[   12.760846] ata2.00: qc timeout (cmd 0xa0)
[   12.786543] ata2.00: TEST_UNIT_READY failed (err_mask=0x5)
[   12.796576] ata2.00: limiting speed to MWDMA2:PIO3
[   12.958455] ata2.01: NODEV after polling detection
[   12.969693] ata2.00: configured for MWDMA2
[   17.972782] ata2.00: qc timeout (cmd 0xa0)
[   17.978967] ata2.00: TEST_UNIT_READY failed (err_mask=0x5)
[   17.983495] ata2.00: disabled
[   17.986352] ata2: soft resetting link
[   18.146586] ata2.01: NODEV after polling detection
[   18.151413] ata2: EH complete
[   32.745227] ata1: lost interrupt (Status 0x50)
[   32.748470] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[   32.756586] ata1.00: failed command: READ DMA
[   32.761251] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[   32.761251]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[   32.773928] ata1.00: status: { DRDY }
[   32.777028] ata1: soft resetting link
[   32.934437] ata1.01: NODEV after polling detection
[   32.946663] ata1.00: configured for MWDMA2
[   32.949964] ata1.00: device reported invalid CHS sector 0
[   32.953793] ata1: EH complete
[   63.849089] ata1: lost interrupt (Status 0x50)
[   63.857470] ata1.00: limiting speed to MWDMA1:PIO4
[   63.860982] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[   63.865862] ata1.00: failed command: READ DMA
[   63.883697] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[   63.883697]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[   63.899573] ata1.00: status: { DRDY }
[   63.902649] ata1: soft resetting link
[   64.062580] ata1.01: NODEV after polling detection
[   64.073800] ata1.00: configured for MWDMA1
[   64.076813] ata1.00: device reported invalid CHS sector 0
[   64.096188] ata1: EH complete

-- 
Regards/Gruss,
    Boris.

ECO tip #101: Trim your mails when you reply.
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/