[PATCH v5 03/14] dt/bindings: Add PIC32 clock binding documentation

[Joshua Henderson]

From: Purna Chandra Mandal <purna.mandal@xxxxxxxxxxxxx>

Document the devicetree bindings for the clock driver found on Microchip
PIC32 class devices.

Signed-off-by: Purna Chandra Mandal <purna.mandal@xxxxxxxxxxxxx>
Signed-off-by: Joshua Henderson <joshua.henderson@xxxxxxxxxxxxx>
Cc: Ralf Baechle <ralf@xxxxxxxxxxxxxx>
Acked-by: Rob Herring <robh@xxxxxxxxxx>
---
Changes since v4: None
Changes since v3: None
Changes since v2:
	- Force lowercase in PIC32 clock binding documentation
Changes since v1: None
---
 .../devicetree/bindings/clock/microchip,pic32.txt  |  257 ++++++++++++++++++++
 1 file changed, 257 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/microchip,pic32.txt

diff --git a/Documentation/devicetree/bindings/clock/microchip,pic32.txt b/Documentation/devicetree/bindings/clock/microchip,pic32.txt
new file mode 100644
index 0000000..06540e4
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/microchip,pic32.txt
@@ -0,0 +1,257 @@
+Binding for a Clock hardware block found on
+certain Microchip PIC32 MCU devices.
+
+Microchip SoC clocks-node consists of few oscillators, PLL, multiplexer
+and few divider nodes.
+
+We will find only the base address of the clock tree, this base
+address is common for some of the subnodes, not all. If no address is
+specified for any of subnode base address of the clock tree will be
+treated as its base. Each of subnodes follow the same common clock
+binding with some additional optional properties.
+
+	clocks_node {
+		reg = <>;
+
+		spll_node {
+			...
+		};
+
+		frcdiv_node {
+			...
+		};
+
+		sysclk_mux_node {
+			...
+		};
+
+		pbdiv_node {
+			...
+		};
+
+		refoclk_node {
+			...
+		};
+		...
+	};
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : should be one of "microchip,pic32mzda-clk",
+    "microchip,pic32mzda-sosc", "microchip,pic32mzda-frcdivclk",
+    "microchip,pic32mzda-syspll", "microchip,pic32mzda-sysclk-v2",
+    "microchip,pic32mzda-pbclk", "microchip,pic32mzda-refoclk".
+- reg : A Base address and length of the register set.
+- interrupts : source of interrupt.
+
+Optional properties (for subnodes):
+- #clock-cells: From common clock binding, should be 0.
+- microchip,clock-indices: in multiplexer node clock sources always aren't linear
+    and contiguous. This property helps define clock-sources with respect to
+    the mux clock node.
+- microchip,ignore-unused : ignore gate request even if the gated clock is unused.
+- microchip,status-bit-mask: bitmask for status check. This will be used to confirm
+    particular operation by clock sub-node is completed. It is dependent sub-node.
+- microchip,bit-mask: enable mask, similar to microchip,status-bit-mask.
+- microchip,slew-step: enable frequency slewing(stepping) during rate change;
+    applicable only to sys-clock subnode.
+
+Example:
+
+/* PIC32 specific clks */
+pic32_clktree {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	reg = <0x1f801200 0x200>;
+	compatible = "microchip,pic32mzda-clk";
+	ranges = <0 0x1f801200 0x200>;
+
+	/* secondary oscillator; external input on SOSCI pin */
+	SOSC:sosc_clk@0 {
+		#clock-cells = <0>;
+		compatible = "microchip,pic32mzda-sosc";
+		clock-frequency = <32768>;
+		reg = <0x000 0x10>, /* enable reg */
+		      <0x1d0 0x10>; /* status reg */
+		microchip,bit-mask = <0x02>; /* enable mask */
+		microchip,status-bit-mask = <0x10>; /* status-mask*/
+	};
+
+	FRCDIV:frcdiv_clk {
+		#clock-cells = <0>;
+		compatible = "microchip,pic32mzda-frcdivclk";
+		clocks = <&FRC>;
+		clock-output-names = "frcdiv_clk";
+	};
+
+	/* System PLL clock */
+	SYSPLL:spll_clk@20 {
+		#clock-cells = <0>;
+		compatible = "microchip,pic32mzda-syspll";
+		reg = <0x020 0x10>, /* SPLL register */
+		      <0x1d0 0x10>; /* CLKSTAT register */
+		clocks = <&POSC>, <&FRC>;
+		clock-output-names = "sys_pll";
+		microchip,status-bit-mask = <0x80>; /* SPLLRDY */
+	};
+
+	/* system clock; mux with postdiv & slew */
+	SYSCLK:sys_clk@1c0 {
+		#clock-cells = <0>;
+		compatible = "microchip,pic32mzda-sysclk-v2";
+		reg = <0x1c0 0x04>; /* SLEWCON */
+		clocks = <&FRCDIV>, <&SYSPLL>, <&POSC>, <&SOSC>,
+			 <&LPRC>, <&FRCDIV>;
+		microchip,clock-indices = <0>, <1>, <2>, <4>,
+					  <5>, <7>;
+		clock-output-names = "sys_clk";
+	};
+
+	/* UPLL is integral part of USB PHY; UTMI clk for USBCORE */
+	UPLL:usb_phy_clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clocks";
+		clock-frequency = <24000000>;
+		clock-output-names = "usbphy_clk";
+	};
+
+	/* Peripheral bus1 clock */
+	PBCLK1:pb1_clk@140 {
+		reg = <0x140 0x10>;
+		#clock-cells = <0>;
+		compatible = "microchip,pic32mzda-pbclk";
+		clocks = <&SYSCLK>;
+		clock-output-names = "pb1_clk";
+		/* used by system modules, not gateable */
+		microchip,ignore-unused;
+	};
+
+	/* Peripheral bus2 clock */
+	PBCLK2:pb2_clk@150 {
+		reg = <0x150 0x10>;
+		#clock-cells = <0>;
+		compatible = "microchip,pic32mzda-pbclk";
+		clocks = <&SYSCLK>;
+		clock-output-names = "pb2_clk";
+		/* avoid gating even if unused */
+		microchip,ignore-unused;
+	};
+
+	/* Peripheral bus3 clock */
+	PBCLK3:pb3_clk@160 {
+		reg = <0x160 0x10>;
+		#clock-cells = <0>;
+		compatible = "microchip,pic32mzda-pbclk";
+		clocks = <&SYSCLK>;
+		clock-output-names = "pb3_clk";
+	};
+
+	/* Peripheral bus4 clock(I/O ports, GPIO) */
+	PBCLK4:pb4_clk@170 {
+		reg = <0x170 0x10>;
+		#clock-cells = <0>;
+		compatible = "microchip,pic32mzda-pbclk";
+		clocks = <&SYSCLK>;
+		clock-output-names = "pb4_clk";
+	};
+
+	/* Peripheral bus clock */
+	PBCLK5:pb5_clk@180 {
+		reg = <0x180 0x10>;
+		#clock-cells = <0>;
+		compatible = "microchip,pic32mzda-pbclk";
+		clocks = <&SYSCLK>;
+		clock-output-names = "pb5_clk";
+	};
+
+	/* Peripheral Bus6 clock; */
+	PBCLK6:pb6_clk@190 {
+		reg = <0x190 0x10>;
+		compatible = "microchip,pic32mzda-pbclk";
+		clocks = <&SYSCLK>;
+		#clock-cells = <0>;
+	};
+
+	/* Peripheral bus7 clock */
+	PBCLK7:pb7_clk@1a0 {
+		reg = <0x1a0 0x10>;
+		#clock-cells = <0>;
+		compatible = "microchip,pic32mzda-pbclk";
+		/* CPU is driven by this clock; so named */
+		clock-output-names = "cpu_clk";
+		clocks = <&SYSCLK>;
+	};
+
+	/* Reference Oscillator clock for SPI/I2S */
+	REFCLKO1:refo1_clk@80 {
+		reg = <0x080 0x20>;
+		#clock-cells = <0>;
+		compatible = "microchip,pic32mzda-refoclk";
+		clocks = <&SYSCLK>, <&PBCLK1>, <&POSC>, <&FRC>, <&LPRC>,
+			<&SOSC>, <&SYSPLL>, <&REFIx>, <&BFRC>;
+		microchip,clock-indices = <0>, <1>, <2>, <3>, <4>,
+					  <5>, <7>, <8>, <9>;
+		clock-output-names = "refo1_clk";
+	};
+
+	/* Reference Oscillator clock for SQI */
+	REFCLKO2:refo2_clk@a0 {
+		reg = <0x0a0 0x20>;
+		#clock-cells = <0>;
+		compatible = "microchip,pic32mzda-refoclk";
+		clocks = <&SYSCLK>, <&PBCLK1>, <&POSC>, <&FRC>, <&LPRC>,
+			 <&SOSC>, <&SYSPLL>, <&REFIx>, <&BFRC>;
+		microchip,clock-indices = <0>, <1>, <2>, <3>, <4>,
+					  <5>, <7>, <8>, <9>;
+		clock-output-names = "refo2_clk";
+	};
+
+	/* Reference Oscillator clock, ADC */
+	REFCLKO3:refo3_clk@c0 {
+		reg = <0x0c0 0x20>;
+		compatible = "microchip,pic32mzda-refoclk";
+		clocks = <&SYSCLK>, <&PBCLK1>, <&POSC>, <&FRC>, <&LPRC>,
+			 <&SOSC>, <&SYSPLL>, <&REFIx>, <&BFRC>;
+		microchip,clock-indices = <0>, <1>, <2>, <3>, <4>,
+					  <5>, <7>, <8>, <9>;
+		#clock-cells = <0>;
+		clock-output-names = "refo3_clk";
+	};
+
+	/* Reference Oscillator clock */
+	REFCLKO4:refo4_clk@e0 {
+		reg = <0x0e0 0x20>;
+		compatible = "microchip,pic32mzda-refoclk";
+		clocks = <&SYSCLK>, <&PBCLK1>, <&POSC>, <&FRC>, <&LPRC>,
+			 <&SOSC>, <&SYSPLL>, <&REFIx>, <&BFRC>;
+		microchip,clock-indices = <0>,<1>,<2>,<3>,<4>,
+					  <5>,<7>,<8>,<9>;
+		#clock-cells = <0>;
+		clock-output-names = "refo4_clk";
+	};
+
+	/* Reference Oscillator clock, LCD */
+	REFCLKO5:refo5_clk@100 {
+		reg = <0x100 0x20>;
+		compatible = "microchip,pic32mzda-refoclk";
+		clocks = <&SYSCLK>,<&PBCLK1>,<&POSC>,<&FRC>,<&LPRC>,
+			 <&SOSC>,<&SYSPLL>,<&REFIx>,<&BFRC>;
+		microchip,clock-indices = <0>, <1>, <2>, <3>, <4>,
+					  <5>, <7>, <8>,<9>;
+		#clock-cells = <0>;
+		clock-output-names = "refo5_clk";
+	};
+};
+
+The clock consumer should specify the desired clock by having the clocks in its
+"clock" phandle cell. For example for UART:
+
+uart2: serial@<> {
+	compatible = "microchip,pic32mzda-uart";
+	reg = <>;
+	interrupts = <>;
+	clocks = <&PBCLK2>;
+}
-- 
1.7.9.5