Re: [PATCH v2 12/16] ARM: Xen: Document UEFI support on Xen ARM virtual platforms

[Shannon Zhao]

On 2016/1/19 1:34, Stefano Stabellini wrote:
> On Mon, 18 Jan 2016, Mark Rutland wrote:
>> On Fri, Jan 15, 2016 at 02:55:25PM +0800, Shannon Zhao wrote:
>>> From: Shannon Zhao <shannon.zhao@xxxxxxxxxx>
>>>
>>> Add a "uefi" node under /hypervisor node in FDT, then Linux kernel could
>>> scan this to get the UEFI information.
>>>
>>> Signed-off-by: Shannon Zhao <shannon.zhao@xxxxxxxxxx>
>>> ---
>>>  Documentation/devicetree/bindings/arm/xen.txt | 42 +++++++++++++++++++++++++++
>>>  1 file changed, 42 insertions(+)
>>>
>>> diff --git a/Documentation/devicetree/bindings/arm/xen.txt b/Documentation/devicetree/bindings/arm/xen.txt
>>> index 0f7b9c2..fbc17ae 100644
>>> --- a/Documentation/devicetree/bindings/arm/xen.txt
>>> +++ b/Documentation/devicetree/bindings/arm/xen.txt
>>> @@ -15,6 +15,36 @@ the following properties:
>>>  - interrupts: the interrupt used by Xen to inject event notifications.
>>>    A GIC node is also required.
>>>  
>>> +To support UEFI on Xen ARM virtual platforms, Xen pupulates the FDT "uefi" node
>>> +under /hypervisor with following parameters:
>>
>> s/pupulates/populates/
>>
>>> +
>>> +________________________________________________________________________________
>>> +Name                      | Size   | Description
>>> +================================================================================
>>> +xen,uefi-system-table     | 64-bit | Guest physical address of the UEFI System
>>> +			  |	   | Table.
>>> +--------------------------------------------------------------------------------
>>> +xen,uefi-mmap-start       | 64-bit | Guest physical address of the UEFI memory
>>> +			  |	   | map.
>>> +--------------------------------------------------------------------------------
>>> +xen,uefi-mmap-size        | 32-bit | Size in bytes of the UEFI memory map
>>> +                          |        | pointed to in previous entry.
>>> +--------------------------------------------------------------------------------
>>> +xen,uefi-mmap-desc-size   | 32-bit | Size in bytes of each entry in the UEFI
>>> +                          |        | memory map.
>>> +--------------------------------------------------------------------------------
>>> +xen,uefi-mmap-desc-ver    | 32-bit | Version of the mmap descriptor format.
>>> +--------------------------------------------------------------------------------
>>> +
>>> +Below is the format of the mmap descriptor.
>>> +typedef struct {
>>> +	u32 type;
>>> +	u32 pad;
>>> +	u64 phys_addr;
>>> +	u64 virt_addr;
>>> +	u64 num_pages;
>>> +	u64 attribute;
>>> +} efi_memory_desc_t;
>>
>> I don't think we should describe this here, as it duplicates the UEFI
>> spec, and is techincally incorrect the above is only guaranteed to be
>> the prefix of each memory descriptor -- that's why the
>> uefi-mmap-desc-size property exists.
>>
Oh, this format is suggested to describe here at previous patch set.

>> We don't do this in Documentation/arm/uefi.txt, and I don't see why we
>> should do so here.
>>
>> Does Xen handle arbitrary size memory map descriptors? I'm not sure what
>> new information might be passed in future additions to the descriptor
>> format, and I'm not sure what should happen in the Dom0 case.
> 
> Xen passes to Dom0 the memory map in the same format as the native
> memory map.
> 
> 
>>>  Example (assuming #address-cells = <2> and #size-cells = <2>):
>>>  
>>> @@ -22,4 +52,16 @@ hypervisor {
>>>  	compatible = "xen,xen-4.3", "xen,xen";
>>>  	reg = <0 0xb0000000 0 0x20000>;
>>>  	interrupts = <1 15 0xf08>;
>>> +	uefi {
>>> +		xen,uefi-system-table = <0xXXXXXXXX>;
>>> +		xen,uefi-mmap-start = <0xXXXXXXXX>;
>>> +		xen,uefi-mmap-size = <0xXXXXXXXX>;
>>> +		xen,uefi-mmap-desc-size = <0xXXXXXXXX>;
>>> +		xen,uefi-mmap-desc-ver = <0xXXXXXXXX>;
>>> +        };
>>>  };
>>> +
>>> +These "xen,uefi-*" parameters are similar to those in Documentation/arm/uefi.txt
>>> +which are used by normal UEFI. But to Xen ARM virtual platforms, it needs to
>>> +introduce a Xen specific UEFI and it doesn't want to mix with normal UEFI.
>>> +Therefore, it defines these parameters under /hypervisor node.
>>
>> Could we please describe what that actual difference is?
>>
>> I know that the OS must handle a system table differently under Xen, but
>> this doesn't describe what it should do.
> 
> For a reference, the hypercall interface is described in not so many words here:
> 
> include/xen/interface/platform.h
> http://xenbits.xen.org/gitweb/?p=xen.git;a=blob_plain;f=xen/include/public/platform.h;hb=HEAD
> 
> However it is clear that platform.h also contains some x86 specific
> calls, for example xenpf_set_processor_pminfo. It might be a good idea
> to list the calls that are available on ARM64.
> 
As Stefano said, I think the difference is that for Xen Dom0 the runtime
services are worked through hypercalls not the RuntimeServices under the
system table.

> 
>> I assume that the OS can handle the memory map in an identical fashion
>> to when it is native. Is that true?
>  
> Yes, I think that's true.
> 
> .
> 

-- 
Shannon