Re: [PATCH V4 1/5] DT: mfd: add device-tree binding doc fro PMIC max77620/max20024
From: Lee Jones
Date: Tue Jan 26 2016 - 09:59:12 EST
On Mon, 25 Jan 2016, Laxman Dewangan wrote:
>
> Thanks Lee for your review. I will take care of most of comment on
> my next patch.
>
> I have reply on some comment and seeking more details for few
> comments as follows.
>
> On Monday 25 January 2016 05:26 PM, Lee Jones wrote:
> >On Tue, 19 Jan 2016, Laxman Dewangan wrote:
> >
> >>+- interrupt-controller: MAX77620 has internal interrupt controller which
> >>+ takes the interrupt request from internal sub-blocks like RTC,
> >>+ regulators, GPIOs as well as external input.
> >This is how interrupt-controllers usually work. I don't think there
> >is any need to explain this. I'd just link to
> >../interrupt-controller/interrupts.txt instead.
>
> Something similar to (just to confirm)
> - interrupt-controller: describes the 88pm860x as an interrupt
> controller (has its own domain)
IRQ domains are Linuxisums, which aren't allowed in DT.
I'd prefer something along the lines of:
"Identifies the node as an interrupt controller."
> >>+- #interrupt-cells: Should be set to 2 for IRQ number and flags.
> >>+ The first cell is the IRQ number. IRQ numbers for different interrupt
> >>+ source of MAX77620 are defined at dt-bindings/mfd/max77620.h
> >>+ The second cell is the flags, encoded as the trigger masks from binding
> >>+ document interrupts.txt, using dt-bindings/irq.
> >This is a very lengthy read for such little information. Please make
> >it more succinct. Take a look at other files for examples.
> I started with as3722.txt and it seems I am carrying forward the
> complexity here. Originally, as3722 is posted by me only. Any good
> file example which I can refer?
Just grep for #interrupt-cells in Documentation. There are plenty of
nice, short examples.
> > Also,
> >tell use where interrupts.txt is
> >i.e. ../interrupt-controller/interrupts.txt.
> >
> >These are so much easier to read if you tab out from the property name
> >to the description.
> >
> >- reg: I2C device address.
> >- interrupt-controller: MAX77620 has internal interrupt controller which
> > takes the interrupt request from internal
> > sub-blocks like RTC, regulators, GPIOs as well
> > as external input.
> >- #interrupt-cells: Should be set to 2 for IRQ number and flags.
> > The first cell is the IRQ number. IRQ numbers
> > for different interrupt source of MAX77620 are
> > defined at dt-bindings/mfd/max77620.h
> > The second cell is the flags, encoded as the
> > trigger masks from binding document
> > interrupts.txt, using dt-bindings/irq.
> >
> >... don't you think?
>
> Agree, I can make indenting. And will do whatever places it needs in
> this document.
>
> >
> >>+Optional properties:
> >>+-------------------
> >>+This device also supports the power OFF of system.
> >What is the "power OFF of system"?
>
> PMIC supplies the power. So once PMIC is in OFF state, it turns off
> all its rail and hence no SW execution on system. Still external
> supply will keep supply to PMIC.
"This device controls platform power" or something.
> >>+Following properties are used for this purpose:
> >>+- system-power-controller: Boolean, This device will be use as
> >You don't describe the type of each property, so why is this one
> >special?
> Hmm. I describe the boolean and tristate only. Do I need to define
> type for integer,string also?
I wouldn't describe any of them. It's normally pretty obvious which
properties are boolean by the lack of required cell description.
> >>+power OFF slot and slot period of the device. Device has 3 FPS as FPS0,
> >>+FPS1 and FPS2. The details of FPS configuration is provided through
> >>+subnode "fps". The details of FPS0, FPS1, FPS2 are provided through the
> >>+child node under this subnodes. The FPS number is provided via reg property.
> >>+
> >>+The property for fps child nodes as:
> >>+Required properties:
> >>+ -reg: FPS number like 0, 1, 2 for FPS0, FPS1 and FPS2 respectively.
> >I'm surprised Rob Acked this. We don't usually do device numbers in DT.
> What is best way to make the child node for FPS and differentiate FPS0,1, 2?
> What is your suggestion here?
There are lots of ways you can solve this and so many examples of
others doing so. I suggest you have a look at some DTS files and
figure it out. One possible solution is to use different compatible
strings.
> >>+ -maxim,active-fps-time-period-us: Active state FPS time period in
> >>+ microseconds.
> >>+ -maxim,suspend-fps-time-period-us: Suspend state FPS time period in
> >>+ microseconds.
> >>+ -maxim,fps-enable-input: FPS enable source like EN0, EN1 or SW. The
> >>+ macros are defined on dt-bindings/mfd/max77620.h for
> >>+ different enable source.
> >>+ FPS_EN_SRC_EN0 for EN0 enable source.
> >>+ FPS_EN_SRC_EN1 for En1 enable source.
> >>+ FPS_EN_SRC_SW for SW based control.
> >>+ -maxim,fps-sw-enable: Boolean, applicable if enable input is SW.
> >>+ If this property present then enable the FPS else
> >"property is present"
> >
> >If this enables/disables FPS, why does it matter if it's SW or not?
> >Why can't you just cal it maxim,fps-enable? Also, is there a case
> >where you would supply this sub-node, have FPS enabled and this
> >property not present? If not, can't you just remove the entire node?
> >Or am I missing something?
>
> Here, my need is to connect different FPS source inputs EN0, EN1 or
> SW. They can connected to any inputs. That's why fps-enable-input
> select the related digital input for given FPS.
> However, I can reduce the need of "fps-sw-enable" and make this
> always enable if fps-enable-input= <SW>.
This is exactly how you need to think. Reducing the number of
properties you introduce (and this device adds a lot more than I would
normally expect by the way) needs to be top priority.
> Here is excerpt from datasheet:
> B3:B1: SRCFPSx[1:0]
> Enable Source. Specifies the enable source for the sequencer.
> 0b00=EN0 hardware input
> 0b01=EN1 hardware input
> 0b10=ENFPSx software bit
> 0b11=reserved
> B0 ENFPSx
> Software Enable
> 0=Disable FPSx
> 1=Enable FPSx
> X=ENFPSx is a donÂt care if SRCFPSx[1:0] != 0b10
>
>
> >
> >>+ -maxim,enable-global-lpm: Boolean, enable global LPM when the external
> >LPM?
> Low Power Mode (LPM). I will add details.
>
> >+Pinmux and GPIO:
> >+===============
> >I think this whole section needs moving to ../pinctrl and needs to be
> >reviewed by Linus W.
>
> Is this mean I need to create DT binding doc for the each subsystem
> differently?
> Actually during AS3722, I had different understanding to have single file.
Yes, that way you have each of the the subsystem experts review your
documentation. You can then link to them from this document.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org â Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog