Re: [PATCH v8 2/2] drm/bridge: Add I2C based driver for ps8640 bridge

From: Daniel Kurtz
Date: Mon Feb 01 2016 - 07:54:21 EST

Next message: Joao Pinto: "[PATCH] add support for DWC UFS Host Controller"
Previous message: Jacek Anaszewski: "Re: [PATCH 3/3] leds: add SN3218 LED driver"
In reply to: kbuild test robot: "Re: [PATCH v8 2/2] drm/bridge: Add I2C based driver for ps8640 bridge"
Next in thread: Daniel Kurtz: "Re: [PATCH v8 2/2] drm/bridge: Add I2C based driver for ps8640 bridge"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Mon, Feb 1, 2016 at 12:13 PM, Jitao Shi <jitao.shi@xxxxxxxxxxxx> wrote:
> This patch adds drm_bridge driver for parade DSI to eDP bridge chip.
>
> Signed-off-by: Jitao Shi <jitao.shi@xxxxxxxxxxxx>
> ---
> Changes since v7:
> - Change ps8640_regw to ps8640_regw_bytes and remove devm_kzalloc
> - Fine tune ps8640 power squence
> - Add ps8640_pre_enable and ps8640_post_disable in ps8640_get_modes
> - Remove unnecessary codes and comments
>
> The following patches are needed to support dsi host through none dsi bus:
>
> https://patchwork.kernel.org/patch/7818431/ ("drm/dsi: check for CONFIG_OF when defining of_mipi_dsi_device_add")
> https://patchwork.kernel.org/patch/7818471/ ("drm/dsi: Refactor device creation")
> https://patchwork.kernel.org/patch/7818501/ ("drm/dsi: Try to match non-DT dsi devices")
> https://patchwork.kernel.org/patch/7818531/ ("drm/dsi: Check for used channels")
> https://patchwork.kernel.org/patch/7818561/ ("drm/dsi: Add routine to unregister dsi device")
> https://patchwork.kernel.org/patch/7818541/ ("drm/dsi: Get DSI host by DT device node")
> ---
> drivers/gpu/drm/bridge/Kconfig | 10 +
> drivers/gpu/drm/bridge/Makefile | 1 +
> drivers/gpu/drm/bridge/parade-ps8640.c | 1084 ++++++++++++++++++++++++++++++++
> 3 files changed, 1095 insertions(+)
> create mode 100644 drivers/gpu/drm/bridge/parade-ps8640.c
>
> diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> index 27e2022..fe8ad50 100644
> --- a/drivers/gpu/drm/bridge/Kconfig
> +++ b/drivers/gpu/drm/bridge/Kconfig
> @@ -40,4 +40,14 @@ config DRM_PARADE_PS8622
> ---help---
> Parade eDP-LVDS bridge chip driver.
>
> +config DRM_PARADE_PS8640
> + tristate "Parade PS8640 MIPI DSI to eDP Converter"
> + depends on OF && I2C
> + select DRM_KMS_HELPER

I think this needs:

select DRM_MIPI_DSI

Otherwise:
drivers/gpu/drm/bridge/parade-ps8640.c:400: undefined reference to
`of_find_mipi_dsi_host_by_node'
drivers/gpu/drm/bridge/parade-ps8640.c:411: undefined reference to
`mipi_dsi_attach'

> + select DRM_PANEL

> + ---help---
> + Choose this option if you have PS8640 for display
> + The PS8640 is a high-performance and low-power
> + MIPI DSI to eDP converter
> +
> endmenu
> diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> index f13c33d..fbe38dc 100644
> --- a/drivers/gpu/drm/bridge/Makefile
> +++ b/drivers/gpu/drm/bridge/Makefile
> @@ -4,3 +4,4 @@ obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
> obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
> obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
> obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
> +obj-$(CONFIG_DRM_PARADE_PS8640) += parade-ps8640.o
> diff --git a/drivers/gpu/drm/bridge/parade-ps8640.c b/drivers/gpu/drm/bridge/parade-ps8640.c
> new file mode 100644
> index 0000000..0230ab5
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/parade-ps8640.c
> @@ -0,0 +1,1084 @@
> +/*
> + * Copyright (c) 2014 MediaTek Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/firmware.h>
> +#include <linux/gpio.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_gpio.h>
> +#include <linux/of_graph.h>
> +#include <linux/regulator/consumer.h>
> +#include <asm/unaligned.h>
> +#include <drm/drm_panel.h>
> +
> +#include <drmP.h>
> +#include <drm_atomic_helper.h>
> +#include <drm_crtc_helper.h>
> +#include <drm_crtc.h>
> +#include <drm_mipi_dsi.h>
> +
> +#define PAGE2_SPI_CFG3 0x82
> +#define I2C_TO_SPI_RESET 0x20
> +#define PAGE2_ROMADD_BYTE1 0x8e
> +#define PAGE2_ROMADD_BYTE2 0x8f
> +#define PAGE2_SWSPI_WDATA 0x90
> +#define PAGE2_SWSPI_RDATA 0x91
> +#define PAGE2_SWSPI_LEN 0x92
> +#define PAGE2_SWSPI_CTL 0x93
> +#define TRIGGER_NO_READBACK 0x05
> +#define TRIGGER_READBACK 0x01
> +#define PAGE2_SPI_STATUS 0x9e
> +#define PAGE2_GPIO_L 0xa6
> +#define PAGE2_GPIO_H 0xa7
> +#define PS_GPIO9 BIT(1)
> +#define PAGE2_IROM_CTRL 0xb0
> +#define IROM_ENABLE 0xc0
> +#define IROM_DISABLE 0x80
> +#define PAGE2_SW_REST 0xbc
> +#define PAGE2_ENCTLSPI_WR 0xda
> +#define PAGE2_I2C_BYPASS 0xea
> +#define I2C_BYPASS_EN 0xd0
> +
> +#define PAGE3_SET_ADD 0xfe
> +#define PAGE3_SET_VAL 0xff
> +#define VDO_CTL_ADD 0x13
> +#define VDO_DIS 0x18
> +#define VDO_EN 0x1c
> +
> +#define PAGE4_REV_L 0xf0
> +#define PAGE4_REV_H 0xf1
> +#define PAGE4_CHIP_L 0xf2
> +#define PAGE4_CHIP_H 0xf3
> +
> +/* Firmware */
> +#define SPI_MAX_RETRY_CNT 8
> +#define PS_FW_NAME "ps864x_fw.bin"
> +
> +#define FW_CHIP_ID_OFFSET 0
> +#define FW_VERSION_OFFSET 2
> +
> +#define bridge_to_ps8640(e) container_of(e, struct ps8640, bridge)
> +#define connector_to_ps8640(e) container_of(e, struct ps8640, connector)
> +
> +struct ps8640_info {
> + u8 family_id;
> + u8 variant_id;
> + u16 version;
> +};
> +
> +struct ps8640 {
> + struct drm_connector connector;
> + struct drm_bridge bridge;
> + struct mipi_dsi_device *dsi;
> + struct i2c_client *page[8];
> + struct ps8640_driver_data *driver_data;
> + struct regulator *pwr_1v2_supply;
> + struct regulator *pwr_3v3_supply;
> + struct drm_panel *panel;
> + struct gpio_desc *gpio_rst_n;
> + struct gpio_desc *gpio_slp_n;
> + struct gpio_desc *gpio_mode_sel_n;
> + bool enabled;
> +
> + /* firmware file name */
> + bool in_fw_update;
> + char *fw_file;
> + struct ps8640_info info;
> +};
> +
> +static const u8 enc_ctrl_code[6] = {0xaa, 0x55, 0x50, 0x41, 0x52, 0x44};
> +
> +static int ps8640_regr(struct i2c_client *client, u8 reg, u8 *data,
> + u16 data_len)

IMHO, ps8640_read() and ps8640_write() are clearer than regr and regw.

> +{
> + int ret;
> + struct i2c_msg msgs[] = {
> + {
> + .addr = client->addr,
> + .flags = 0,
> + .len = 1,
> + .buf = &reg,
> + },
> + {
> + .addr = client->addr,
> + .flags = I2C_M_RD,
> + .len = data_len,
> + .buf = data,
> + }
> + };
> +
> + ret = i2c_transfer(client->adapter, msgs, 2);
> +
> + if (ret == 2)
> + return 0;
> + if (ret < 0)
> + return ret;
> + else
> + return -EIO;
> +}
> +
> +static int ps8640_regw_bytes(struct i2c_client *client, u8 *data,
> + u16 data_len)
> +{
> + int ret;
> + struct i2c_msg msg;
> +
> + msg.addr = client->addr;
> + msg.flags = 0;
> + msg.len = data_len;
> + msg.buf = data;
> +
> + ret = i2c_transfer(client->adapter, &msg, 1);
> + if (ret == 1)
> + return 0;
> + if (ret < 0)
> + return ret;
> + else
> + return -EIO;
> +}
> +
> +static int ps8640_regw_byte(struct i2c_client *client, u8 reg, u8 data)
> +{
> + int ret;
> + struct i2c_msg msg;
> + u8 buf[] = {reg, data};
> +
> + msg.addr = client->addr;
> + msg.flags = 0;
> + msg.len = sizeof(buf);
> + msg.buf = buf;
> +
> + ret = i2c_transfer(client->adapter, &msg, 1);
> + if (ret == 1)
> + return 0;
> + if (ret < 0)
> + return ret;
> + else
> + return -EIO;
> +}
> +
> +static void ps8640_get_mcu_fw_version(struct ps8640 *ps_bridge)
> +{
> + struct i2c_client *client = ps_bridge->page[5];
> + u8 fw_ver[2];
> +
> + ps8640_regr(client, 0x4, fw_ver, 2);
> + ps_bridge->info.version = (fw_ver[0] << 8) | fw_ver[1];
> +
> + DRM_INFO_ONCE("ps8640 rom fw version %d.%d\n", fw_ver[0], fw_ver[1]);
> +}
> +
> +static int ps8640_bridge_enable(struct ps8640 *ps_bridge)
> +{
> + struct i2c_client *client = ps_bridge->page[3];
> + int ret;
> + u8 vdo_ctrl_buf[3] = {PAGE3_SET_ADD, VDO_CTL_ADD, VDO_EN};
> +
> + ret = ps8640_regw_bytes(client, vdo_ctrl_buf, 3);
> + return ret;

nit: Just:

return ps8640_regw_bytes(client, vdo_ctrl_buf, 3);

> +}
> +
> +static void ps8640_pre_enable(struct drm_bridge *bridge)
> +{
> + struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
> + struct i2c_client *client = ps_bridge->page[2];
> + int err, retry_cnt = 0;
> + u8 set_vdo_done;
> +
> + if (ps_bridge->in_fw_update)
> + return;
> +
> + if (ps_bridge->enabled)
> + return;
> +
> + err = drm_panel_prepare(ps_bridge->panel);
> + if (err < 0) {
> + DRM_ERROR("failed to prepare panel: %d\n", err);
> + return;
> + }
> +
> + gpiod_set_value(ps_bridge->gpio_slp_n, 1);
> + gpiod_set_value(ps_bridge->gpio_rst_n, 0);
> +
> + err = regulator_enable(ps_bridge->pwr_1v2_supply);
> + if (err < 0) {
> + DRM_ERROR("failed to enable vdd12-supply: %d\n", err);
> + goto err_panel_unprepare;
> + }
> +
> + err = regulator_enable(ps_bridge->pwr_3v3_supply);
> + if (err < 0) {
> + DRM_ERROR("failed to enable vdd33-supply: %d\n", err);
> + goto err_regulator_1v2_disable;
> + }
> +
> + usleep_range(500, 700);
> + gpiod_set_value(ps_bridge->gpio_rst_n, 1);
> +
> + /*
> + * Wait for the ps8640 embed mcu ready
> + * First wait 200ms and then check the mcu ready flag every 20ms
> + */
> + msleep(200);
> + do {
> + err = ps8640_regr(client, PAGE2_GPIO_H, &set_vdo_done, 1);
> + if (err < 0) {
> + DRM_ERROR("failed read PAGE2_GPIO_H: %d\n", err);
> + goto err_regulator_1v2_disable;
> + }
> + msleep(20);
> + } while ((retry_cnt++ < 10) && ((set_vdo_done & PS_GPIO9) != PS_GPIO9));
> +
> + if (ps_bridge->info.version == 0)
> + ps8640_get_mcu_fw_version(ps_bridge);
> + /* Switch access edp panel's edid through i2c */
> + ps8640_regw_byte(client, PAGE2_I2C_BYPASS, I2C_BYPASS_EN);
> + ps_bridge->enabled = true;
> +
> + return;
> +
> +err_regulator_1v2_disable:
> + regulator_disable(ps_bridge->pwr_1v2_supply);
> +err_panel_unprepare:
> + drm_panel_unprepare(ps_bridge->panel);
> +}
> +
> +static void ps8640_enable(struct drm_bridge *bridge)
> +{
> + struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
> + int err;
> +
> + err = ps8640_bridge_enable(ps_bridge);
> + if (err)
> + DRM_ERROR("failed to enable unmutevideo: %d\n", err);
> +
> + err = drm_panel_enable(ps_bridge->panel);
> + if (err < 0)
> + DRM_ERROR("failed to enable panel: %d\n", err);
> +}
> +
> +static void ps8640_disable(struct drm_bridge *bridge)
> +{
> + struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
> + int err;
> +
> + err = drm_panel_disable(ps_bridge->panel);
> + if (err < 0)
> + DRM_ERROR("failed to disable panel: %d\n", err);

Should there be a ps8640_bridge_disable() here, to undo ps8640_bridge_enable()?

> +}
> +
> +static void ps8640_post_disable(struct drm_bridge *bridge)
> +{
> + struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
> + int err;
> +
> + if (ps_bridge->in_fw_update)
> + return;
> +
> + if (!ps_bridge->enabled)
> + return;
> +
> + ps_bridge->enabled = false;
> +
> + gpiod_set_value(ps_bridge->gpio_rst_n, 0);
> + gpiod_set_value(ps_bridge->gpio_slp_n, 0);
> + regulator_disable(ps_bridge->pwr_3v3_supply);
> + regulator_disable(ps_bridge->pwr_1v2_supply);
> +
> + err = drm_panel_unprepare(ps_bridge->panel);
> + if (err)
> + DRM_ERROR("failed to unprepare panel: %d\n", err);
> +}
> +
> +static int ps8640_get_modes(struct drm_connector *connector)
> +{
> + struct ps8640 *ps_bridge = connector_to_ps8640(connector);
> + bool power_off;
> + int num_modes = 0;
> +
> + power_off = !ps_bridge->enabled;
> + ps8640_pre_enable(&ps_bridge->bridge);
> +
> + num_modes = drm_panel_get_modes(ps_bridge->panel);
> +
> + if (power_off)
> + ps8640_post_disable(&ps_bridge->bridge);
> +
> + return num_modes;
> +}
> +
> +static struct drm_encoder *ps8640_best_encoder(struct drm_connector *connector)
> +{
> + struct ps8640 *ps_bridge;
> +
> + ps_bridge = connector_to_ps8640(connector);
> + return ps_bridge->bridge.encoder;
> +}
> +
> +static const struct drm_connector_helper_funcs ps8640_connector_helper_funcs = {
> + .get_modes = ps8640_get_modes,
> + .best_encoder = ps8640_best_encoder,
> +};
> +
> +static enum drm_connector_status ps8640_detect(struct drm_connector *connector,
> + bool force)
> +{
> + return connector_status_connected;
> +}
> +
> +static void ps8640_connector_destroy(struct drm_connector *connector)
> +{
> + drm_connector_unregister(connector);
> + drm_connector_cleanup(connector);
> +}
> +
> +static const struct drm_connector_funcs ps8640_connector_funcs = {
> + .dpms = drm_atomic_helper_connector_dpms,
> + .fill_modes = drm_helper_probe_single_connector_modes,
> + .detect = ps8640_detect,
> + .destroy = ps8640_connector_destroy,
> + .reset = drm_atomic_helper_connector_reset,
> + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> +};
> +
> +int ps8640_bridge_attach(struct drm_bridge *bridge)
> +{
> + struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
> + struct device *dev = &ps_bridge->page[0]->dev;
> + struct device_node *np = dev->of_node;
> + struct device_node *port, *in_ep;
> + struct device_node *dsi_node = NULL;
> + struct mipi_dsi_host *host = ps_bridge->dsi->host;
> + int ret;
> +
> + ret = drm_connector_init(bridge->dev, &ps_bridge->connector,
> + &ps8640_connector_funcs,
> + DRM_MODE_CONNECTOR_eDP);
> +
> + if (ret) {
> + DRM_ERROR("Failed to initialize connector with drm: %d\n", ret);
> + return ret;
> + }
> +
> + drm_connector_helper_add(&ps_bridge->connector,
> + &ps8640_connector_helper_funcs);
> + drm_connector_register(&ps_bridge->connector);
> +
> + ps_bridge->connector.dpms = DRM_MODE_DPMS_ON;
> + drm_mode_connector_attach_encoder(&ps_bridge->connector,
> + bridge->encoder);
> +
> + if (ps_bridge->panel)
> + drm_panel_attach(ps_bridge->panel, &ps_bridge->connector);
> +
> + /* port@0 is ps8640 dsi input port */
> + port = of_graph_get_port_by_id(np, 0);
> + if (port) {
> + in_ep = of_get_child_by_name(port, "endpoint");
> + of_node_put(port);
> + if (in_ep) {
> + dsi_node = of_graph_get_remote_port_parent(in_ep);
> + of_node_put(in_ep);
> + }
> + }
> + if (dsi_node) {
> + host = of_find_mipi_dsi_host_by_node(dsi_node);
> + of_node_put(dsi_node);
> + if (!host)
> + return -ENODEV;
> + }
> +
> + ps_bridge->dsi->host = host;
> + ps_bridge->dsi->mode_flags = MIPI_DSI_MODE_VIDEO |
> + MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
> + ps_bridge->dsi->format = MIPI_DSI_FMT_RGB888;
> + ps_bridge->dsi->lanes = 4;
> + ret = mipi_dsi_attach(ps_bridge->dsi);
> + if (ret) {
> + drm_panel_detach(ps_bridge->panel);
> + return ret;
> + }
> +
> + return ret;
> +}
> +
> +static const struct drm_bridge_funcs ps8640_bridge_funcs = {
> + .attach = ps8640_bridge_attach,
> + .disable = ps8640_disable,
> + .post_disable = ps8640_post_disable,
> + .pre_enable = ps8640_pre_enable,
> + .enable = ps8640_enable,
> +};
> +
> +static ssize_t ps8640_fw_file_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct ps8640 *ps_bridge = dev_get_drvdata(dev);
> +
> + return scnprintf(buf, PAGE_SIZE, "%s\n", ps_bridge->fw_file);
> +}
> +
> +static int ps8640_update_file_name(struct device *dev, char **file_name,
> + const char *buf, size_t count)

Just remove this function now since fw_file is always just PS_FW_NAME.

> +{
> + char *new_file_name;
> +
> + /* Simple sanity check */
> + if (count > 64) {
> + dev_warn(dev, "File name too long\n");
> + return -EINVAL;
> + }
> +
> + new_file_name = devm_kmalloc(dev, count + 1, GFP_KERNEL);
> + if (!new_file_name)
> + return -ENOMEM;
> +
> + memcpy(new_file_name, buf, count + 1);
> +
> + /* Echo into the sysfs entry may append newline at the end of buf */
> + if (new_file_name[count - 1] == '\n')
> + count--;
> +
> + new_file_name[count] = '\0';
> +
> + if (*file_name)
> + devm_kfree(dev, *file_name);
> +
> + *file_name = new_file_name;
> +
> + return 0;
> +}
> +
> +/* Firmware Version is returned as Major.Minor.Build */
> +static ssize_t ps8640_fw_version_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct ps8640 *ps_bridge = dev_get_drvdata(dev);
> + struct ps8640_info *info = &ps_bridge->info;
> +
> + return scnprintf(buf, PAGE_SIZE, "%u.%u\n", info->version >> 8,
> + info->version & 0xff);

Just remove this sysfs entry since fw_file is always just PS_FW_NAME.

> +}
> +
> +/* Hardware Version is returned as FamilyID.VariantID */
> +static ssize_t ps8640_hw_version_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct ps8640 *ps_bridge = dev_get_drvdata(dev);
> + struct ps8640_info *info = &ps_bridge->info;
> +
> + return scnprintf(buf, PAGE_SIZE, "ps%u.%u\n", info->family_id,
> + info->variant_id);
> +}
> +
> +static int ps8640_spi_send_cmd(struct ps8640 *ps_bridge, u8 *cmd, u8 cmd_len)
> +{
> + struct i2c_client *client = ps_bridge->page[2];
> + u8 i;
> + int ret;
> +
> + ret = ps8640_regw_byte(client, PAGE2_IROM_CTRL, IROM_ENABLE);
> + if (ret)
> + goto err;
> +
> + /* write command in write port */
> + for (i = 0; i < cmd_len; i++) {
> + ret = ps8640_regw_byte(client, PAGE2_SWSPI_WDATA, cmd[i]);
> + if (ret)
> + goto err;
> + }
> + /* command length */
> + ret = ps8640_regw_byte(client, PAGE2_SWSPI_LEN, cmd_len - 1);
> + if (ret)
> + goto err;
> + /* trigger read */
> + ret = ps8640_regw_byte(client, PAGE2_SWSPI_CTL, TRIGGER_NO_READBACK);
> + if (ret)
> + goto err;

nit: you can probably combine the write of PAGE2_SWSPI_LEN &
PAGE2_SWSPI_CTL into a single i2c transaction, here and in
ps8640_wait_spi_nobusy().

> +
> + ret = ps8640_regw_byte(client, PAGE2_IROM_CTRL, IROM_DISABLE);
> + if (ret)
> + goto err;
> +
> + return 0;
> +
> +err:
> + dev_err(&client->dev, "send command err: %d\n", ret);
> + return ret;
> +}
> +
> +static int ps8640_wait_spi_ready(struct ps8640 *ps_bridge)
> +{
> + struct i2c_client *client = ps_bridge->page[2];
> + u8 spi_rdy_st, retry_cnt = 0;
> +
> + do {
> + ps8640_regr(client, PAGE2_SPI_STATUS, &spi_rdy_st, 1);
> + msleep(20);
> + if ((retry_cnt == SPI_MAX_RETRY_CNT) &&
> + ((spi_rdy_st & 0x0c) != 0x0c)) {
> + dev_err(&client->dev, "wait spi ready timeout\n");
> + return -EBUSY;
> + }
> + } while ((retry_cnt++ < SPI_MAX_RETRY_CNT) &&
> + (spi_rdy_st & 0x0c) == 0x0c);
> +
> + return 0;
> +}
> +
> +static int ps8640_wait_spi_nobusy(struct ps8640 *ps_bridge)
> +{
> + struct i2c_client *client = ps_bridge->page[2];
> + u8 spi_status, retry_cnt = 0;
> + int ret;
> +
> + do {
> + /* 0x05 RDSR; Read-Status-Register */
> + ret = ps8640_regw_byte(client, PAGE2_SWSPI_WDATA, 0x05);

Please #define this constant 0x05.

> + if (ret)
> + goto err_send_cmd_exit;
> +
> + /* command length */
> + ret = ps8640_regw_byte(client, PAGE2_SWSPI_LEN, 0x00);
> + if (ret)
> + goto err_send_cmd_exit;
> +
> + /* trigger read */
> + ret = ps8640_regw_byte(client, PAGE2_SWSPI_CTL,
> + TRIGGER_READBACK);
> + if (ret)
> + goto err_send_cmd_exit;
> +
> + /* delay for cmd send */
> + usleep_range(100, 300);
> + /* wait for SPI ROM until not busy */
> + ret = ps8640_regr(client, PAGE2_SWSPI_RDATA, &spi_status, 1);
> + if (ret)
> + goto err_send_cmd_exit;
> + } while ((retry_cnt++ < SPI_MAX_RETRY_CNT) &&
> + (spi_status & 0x0c) == 0x0c);
> +
> + if ((retry_cnt > SPI_MAX_RETRY_CNT) && (spi_status & 0x0c) != 0x0c) {

Please #define this constant 0x0c.

> + ret = -EBUSY;
> + dev_err(&client->dev, "wait spi no busy timeout: %d\n", ret);
> + goto err_timeout;
> + }
> +
> + return 0;
> +
> +err_send_cmd_exit:
> + dev_err(&client->dev, "send command err: %d\n", ret);
> +
> +err_timeout:
> + return ret;
> +}
> +
> +static int ps8640_wait_rom_idle(struct ps8640 *ps_bridge)
> +{
> + struct i2c_client *client = ps_bridge->page[0];
> + int ret;
> +
> + ret = ps8640_regw_byte(client, PAGE2_IROM_CTRL, IROM_ENABLE);
> + if (ret)
> + goto exit;
> +
> + ret = ps8640_wait_spi_ready(ps_bridge);
> + if (ret)
> + goto exit;
> +
> + ret = ps8640_wait_spi_nobusy(ps_bridge);
> + if (ret)
> + goto exit;
> +
> + ret = ps8640_regw_byte(client, PAGE2_IROM_CTRL, IROM_DISABLE);
> + if (ret)
> + goto exit;
> +
> +exit:
> + if (ret)
> + dev_err(&client->dev, "wait ps8640 rom idle fail: %d\n", ret);
> +
> + return ret;
> +}
> +
> +static int ps8640_spi_dl_mode(struct ps8640 *ps_bridge)
> +{
> + struct i2c_client *client = ps_bridge->page[2];
> + int ret;
> +
> + /* switch ps8640 mode to spi dl mode */
> + gpiod_set_value(ps_bridge->gpio_mode_sel_n, 0);
> +
> + /* reset spi interface */
> + ret = ps8640_regw_byte(client, PAGE2_SW_REST, 0xc0);

Please #define these constants, 0xc0 & 0x40. Is this a bit field?

> + if (ret)
> + goto exit;
> +
> + ret = ps8640_regw_byte(client, PAGE2_SW_REST, 0x40);
> + if (ret)
> + goto exit;
> +
> +exit:
> + if (ret)
> + dev_err(&client->dev, "fail reset spi interface: %d\n", ret);
> +
> + return ret;
> +}
> +
> +static int ps8640_rom_prepare(struct ps8640 *ps_bridge)
> +{
> + struct i2c_client *client = ps_bridge->page[2];
> + struct device *dev = &client->dev;
> + u8 i, cmd[2];
> + int ret;
> +
> + /* Enable-Write-Status-Register */
> + cmd[0] = 0x06;

Please #define magic numbers / constants in this function.

> + ret = ps8640_spi_send_cmd(ps_bridge, cmd, 1);
> + if (ret) {
> + dev_err(dev, "failed enable-write-status-register: %d\n", ret);
> + return ret;
> + }
> +
> + /* disable all protection */
> + cmd[0] = 0x01;
> + cmd[1] = 0x00;
> + ret = ps8640_spi_send_cmd(ps_bridge, cmd, 2);
> + if (ret) {
> + dev_err(dev, "fail disable all protection: %d\n", ret);
> + return ret;
> + }
> +
> + /* wait for SPI module ready */
> + ret = ps8640_wait_rom_idle(ps_bridge);
> + if (ret) {
> + dev_err(dev, "fail wait rom idle: %d\n", ret);
> + return ret;
> + }
> +
> + ps8640_regw_byte(client, PAGE2_IROM_CTRL, IROM_ENABLE);
> + for (i = 0; i < 6; i++)
> + ps8640_regw_byte(client, PAGE2_ENCTLSPI_WR, enc_ctrl_code[i]);
> + ps8640_regw_byte(client, PAGE2_IROM_CTRL, IROM_DISABLE);
> +
> + /* Enable-Write-Status-Register */
> + cmd[0] = 0x06;
> + ret = ps8640_spi_send_cmd(ps_bridge, cmd, 1);
> + if (ret) {
> + dev_err(dev, "fail enable-write-status-register: %d\n", ret);
> + return ret;
> + }
> +
> + /* chip erase command */
> + cmd[0] = 0xc7;
> + ret = ps8640_spi_send_cmd(ps_bridge, cmd, 1);
> + if (ret) {
> + dev_err(dev, "fail disable all protection: %d\n", ret);
> + return ret;
> + }
> +
> + ret = ps8640_wait_rom_idle(ps_bridge);
> + if (ret) {
> + dev_err(dev, "fail wait rom idle: %d\n", ret);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int ps8640_validate_firmware(struct ps8640 *ps_bridge,
> + const struct firmware *fw)
> +{
> + struct i2c_client *client = ps_bridge->page[0];
> + struct ps8640_info *info = &ps_bridge->info;
> + u16 fw_chip_id, fw_version_id;
> +
> + /*
> + * Get the chip_id from the firmware. Make sure that it is the
> + * right controller to do the firmware and config update.
> + */
> + fw_chip_id = get_unaligned_le16(fw->data + FW_CHIP_ID_OFFSET);
> +
> + if (fw_chip_id != 0x8640) {
> + dev_err(&client->dev,
> + "chip id mismatch: fw 0x%x vs. chip 0x8640\n",
> + fw_chip_id);
> + return -ENODEV;
> + }
> +
> + fw_version_id = get_unaligned_le16(fw->data + FW_VERSION_OFFSET);
> +
> + if (fw_chip_id != info->version) {
> + dev_err(&client->dev,
> + "fw version mismatch: fw %d.%d vs. chip %d.%d\n",
> + fw_version_id >> 8, fw_version_id & 0xff,
> + info->version >> 8, info->version & 0xff);
> + return -ENODEV;
> + }
> +
> + return 0;
> +}
> +
> +static int ps8640_write_rom(struct ps8640 *ps_bridge, const struct firmware *fw)
> +{
> + struct i2c_client *client = ps_bridge->page[0];
> + struct device *dev = &client->dev;
> + struct i2c_client *client2 = ps_bridge->page[2];
> + struct i2c_client *client7 = ps_bridge->page[7];
> + unsigned int pos = 0;
> + u8 buf[257], rom_page_id_buf[3];
> + int ret;
> + u16 cpy_len;
> +
> + ps8640_regw_byte(client2, PAGE2_SPI_CFG3, I2C_TO_SPI_RESET);
> + msleep(100);
> + ps8640_regw_byte(client2, PAGE2_SPI_CFG3, 0x00);
> +
> + while (pos < fw->size) {
> + rom_page_id_buf[0] = PAGE2_ROMADD_BYTE1;
> + rom_page_id_buf[1] = (pos >> 8) & 0xff;
> + rom_page_id_buf[2] = (pos >> 16) & 0xff;
> + ret = ps8640_regw_bytes(client2, rom_page_id_buf, 3);
> + if (ret)
> + goto error;
> + cpy_len = fw->size >= 256 + pos ? 256 : fw->size - pos;
> + buf[0] = 0;
> + memcpy(buf + 1, fw->data + pos, cpy_len);
> + ret = ps8640_regw_bytes(client7, buf, cpy_len + 1);
> + if (ret)
> + goto error;
> +
> + pos += cpy_len;
> +
> + dev_dbg(dev, "fw update completed %u / %zu bytes\n", pos,
> + fw->size);
> + }
> + return 0;
> +
> +error:
> + dev_err(dev, "failed write extenal flash, %d\n", ret);
> + return ret;
> +}
> +
> +static int ps8640_spi_normal_mode(struct ps8640 *ps_bridge)
> +{
> + u8 cmd[2];
> + struct i2c_client *client = ps_bridge->page[2];

Please #define magic numbers / constants in this function.

> +
> + /* Enable-Write-Status-Register */
> + cmd[0] = 0x06;
> + ps8640_spi_send_cmd(ps_bridge, cmd, 1);
> +
> + /* protect BPL/BP0/BP1 */
> + cmd[0] = 0x01;
> + cmd[1] = 0x8c;
> + ps8640_spi_send_cmd(ps_bridge, cmd, 2);
> +
> + /* wait for SPI rom ready */
> + ps8640_wait_rom_idle(ps_bridge);
> +
> + /* disable PS8640 mapping function */
> + ps8640_regw_byte(client, PAGE2_ENCTLSPI_WR, 0x00);
> +
> + gpiod_set_value(ps_bridge->gpio_mode_sel_n, 1);
> + return 0;
> +}
> +
> +static int ps8640_enter_bl(struct ps8640 *ps_bridge)
> +{
> + int ret;
> +
> + ret = ps8640_spi_dl_mode(ps_bridge);
> + if (ret)
> + return ret;
> +
> + ps_bridge->in_fw_update = true;

Set in_fw_update before ps8640_spi_dl_mode() to avoid a race between
between ps8640_spi_dl_mode() and ps8640_pre_enable / post_disable().

> + return 0;
> +}
> +
> +static void ps8640_exit_bl(struct ps8640 *ps_bridge, const struct firmware *fw)
> +{
> + ps_bridge->in_fw_update = false;
> + ps8640_spi_normal_mode(ps_bridge);

Set in_fw_update after ps8640_spi_normal_mode() to avoid a race
between between ps8640_spi_normal_mode() and ps8640_pre_enable /
post_disable().

> +}
> +
> +static int ps8640_load_fw(struct ps8640 *ps_bridge, const struct firmware *fw)
> +{
> + struct i2c_client *client = ps_bridge->page[0];
> + struct device *dev = &client->dev;
> + int ret;
> + bool ps8640_status_backup = ps_bridge->enabled;
> +
> + if (!ps_bridge->in_fw_update) {
> + if (!ps8640_status_backup)
> + ps8640_pre_enable(&ps_bridge->bridge);
> +
> + ret = ps8640_enter_bl(ps_bridge);
> + if (ret)
> + goto exit;
> + }
> +
> + ret = ps8640_validate_firmware(ps_bridge, fw);
> + if (ret)
> + goto exit;
> +
> + ret = ps8640_rom_prepare(ps_bridge);
> + if (ret)
> + goto exit;
> +
> + ret = ps8640_write_rom(ps_bridge, fw);
> +
> +exit:
> + if (ret)
> + dev_err(dev, "Failed to load firmware, %d\n", ret);
> +
> + ps8640_exit_bl(ps_bridge, fw);
> + if (!ps8640_status_backup)
> + ps8640_post_disable(&ps_bridge->bridge);
> + return ret;
> +}
> +
> +static ssize_t ps8640_update_fw_store(struct device *dev,
> + struct device_attribute *attr,
> + const char *buf, size_t count)
> +{
> + struct i2c_client *client = to_i2c_client(dev);
> + struct ps8640 *ps_bridge = i2c_get_clientdata(client);
> + const struct firmware *fw;
> + int error;
> +
> + error = request_firmware(&fw, ps_bridge->fw_file, dev);
> + if (error) {
> + dev_err(dev, "Unable to open firmware %s: %d\n",
> + ps_bridge->fw_file, error);
> + return error;
> + }
> +
> + error = ps8640_load_fw(ps_bridge, fw);
> + if (error)
> + dev_err(dev, "The firmware update failed(%d)\n", error);
> + else
> + dev_info(dev, "The firmware update succeeded\n");
> +
> + release_firmware(fw);
> + return error ? error : count;
> +}
> +
> +static DEVICE_ATTR(fw_file, S_IRUGO, ps8640_fw_file_show, NULL);
> +static DEVICE_ATTR(fw_version, S_IRUGO, ps8640_fw_version_show, NULL);
> +static DEVICE_ATTR(hw_version, S_IRUGO, ps8640_hw_version_show, NULL);
> +static DEVICE_ATTR(update_fw, S_IWUSR, NULL, ps8640_update_fw_store);
> +
> +static struct attribute *ps8640_attrs[] = {
> + &dev_attr_fw_file.attr,
> + &dev_attr_fw_version.attr,
> + &dev_attr_hw_version.attr,
> + &dev_attr_update_fw.attr,
> + NULL
> +};
> +
> +static const struct attribute_group ps8640_attr_group = {
> + .attrs = ps8640_attrs,
> +};
> +
> +static void ps8640_remove_sysfs_group(void *data)
> +{
> + struct ps8640 *ps_bridge = data;
> +
> + sysfs_remove_group(&ps_bridge->page[0]->dev.kobj, &ps8640_attr_group);
> +}
> +
> +static int ps8640_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct device *dev = &client->dev;
> + struct ps8640 *ps_bridge;
> + struct device_node *np = dev->of_node;
> + struct device_node *port, *out_ep;
> + struct device_node *panel_node = NULL;
> + int i, ret;
> +
> + ps_bridge = devm_kzalloc(dev, sizeof(*ps_bridge), GFP_KERNEL);
> + ps_bridge->dsi = devm_kzalloc(dev, sizeof(struct mipi_dsi_device),
> + GFP_KERNEL);
> + if (!ps_bridge) {
> + ret = -ENOMEM;
> + goto exit;

nit: instead of "goto exit", you can just:

return -ENOMEM; (for all of these "goto exit")

> + }
> + /* port@1 is ps8640 output port */
> + port = of_graph_get_port_by_id(np, 1);
> + if (port) {
> + out_ep = of_get_child_by_name(port, "endpoint");
> + of_node_put(port);
> + if (out_ep) {
> + panel_node = of_graph_get_remote_port_parent(out_ep);
> + of_node_put(out_ep);
> + }
> + }
> + if (panel_node) {
> + ps_bridge->panel = of_drm_find_panel(panel_node);
> + of_node_put(panel_node);
> + if (!ps_bridge->panel) {
> + ret = -EPROBE_DEFER;
> + goto exit;
> + }
> + }
> +
> + ps_bridge->pwr_3v3_supply = devm_regulator_get(dev, "vdd33");
> + if (IS_ERR(ps_bridge->pwr_3v3_supply)) {
> + ret = PTR_ERR(ps_bridge->pwr_3v3_supply);
> + dev_err(dev, "cannot get vdd33 supply: %d\n", ret);
> + goto exit;
> + }
> +
> + ps_bridge->pwr_1v2_supply = devm_regulator_get(dev, "vdd12");
> + if (IS_ERR(ps_bridge->pwr_1v2_supply)) {
> + ret = PTR_ERR(ps_bridge->pwr_1v2_supply);
> + dev_err(dev, "cannot get vdd12 supply: %d\n", ret);
> + goto exit;
> + }
> +
> + ps_bridge->gpio_mode_sel_n = devm_gpiod_get(&client->dev, "mode-sel",
> + GPIOD_OUT_HIGH);
> + if (IS_ERR(ps_bridge->gpio_mode_sel_n)) {
> + ret = PTR_ERR(ps_bridge->gpio_mode_sel_n);
> + dev_err(dev, "cannot get gpio_mode_sel_n %d\n", ret);

nit: I'd use the gpio's device tree name in the error message here, so
"mode-sel".
Same for the others, below.

dev_err(dev, "cannot get gpio 'mode-sel' %d\n", ret);

Thanks,
-Dan

Next message: Joao Pinto: "[PATCH] add support for DWC UFS Host Controller"
Previous message: Jacek Anaszewski: "Re: [PATCH 3/3] leds: add SN3218 LED driver"
In reply to: kbuild test robot: "Re: [PATCH v8 2/2] drm/bridge: Add I2C based driver for ps8640 bridge"
Next in thread: Daniel Kurtz: "Re: [PATCH v8 2/2] drm/bridge: Add I2C based driver for ps8640 bridge"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]