Re: [PATCH 01/10] serial: mvebu-uart: initial support for Armada-3700 serial port
From: Mark Rutland
Date: Tue Feb 02 2016 - 13:20:09 EST
On Tue, Feb 02, 2016 at 07:07:39PM +0100, Gregory CLEMENT wrote:
> From: Wilson Ding <dingwei@xxxxxxxxxxx>
>
> Armada-3700's uart is a simple serial port, which doesn't
> support. Configuring the modem control lines. The uart port has a 32
> bytes Tx FIFO and a 64 bytes Rx FIFO
>
> The uart driver implements the uart core operations. It also support the
> system (early) console based on Armada-3700's serial port.
>
> Known Issue:
>
> The uart driver currently doesn't support clock programming, which means
> the baud-rate stays with the default value configured by the bootloader
> at boot time
This looks like any other early console.
Why does this not use the earlycon infrastructure?
See {OF_,}EARLYCON_DECLARE (e.g. in drivers/tty/serial/amba-pl011.c).
Mark.
> [gregory.clement@xxxxxxxxxxxxxxxxxx: Rewrite many part which are too long
> to enumerate]
>
> Signed-off-by: Wilson Ding <dingwei@xxxxxxxxxxx>
> Signed-off-by: Nadav Haklai <nadavh@xxxxxxxxxxx>
> Signed-off-by: Gregory CLEMENT <gregory.clement@xxxxxxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/tty/serial/mvebu-uart.txt | 13 +
> Documentation/kernel-parameters.txt | 6 +
> drivers/tty/serial/Kconfig | 22 +
> drivers/tty/serial/Makefile | 1 +
> drivers/tty/serial/mvebu-uart.c | 649 +++++++++++++++++++++
> include/uapi/linux/serial_core.h | 3 +
> 6 files changed, 694 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt
> create mode 100644 drivers/tty/serial/mvebu-uart.c
>
> diff --git a/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt b/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt
> new file mode 100644
> index 000000000000..6087defd9f93
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt
> @@ -0,0 +1,13 @@
> +* Marvell UART : Non standard UART used in some of Marvell EBU SoCs (e.g., Armada-3700)
> +
> +Required properties:
> +- compatible: "marvell,armada-3700-uart"
> +- reg: offset and length of the register set for the device.
> +- interrupts: device interrupt
> +
> +Example:
> + serial@12000 {
> + compatible = "marvell,armada-3700-uart";
> + reg = <0x12000 0x400>;
> + interrupts = <43>;
> + };
> diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
> index 87d40a72f6a1..198f6bd56e84 100644
> --- a/Documentation/kernel-parameters.txt
> +++ b/Documentation/kernel-parameters.txt
> @@ -1058,6 +1058,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
> A valid base address must be provided, and the serial
> port must already be setup and configured.
>
> + mvebu_uart,<addr>
> + Start an early, polled-mode console on an some mvebu
> + SoC (as the Armada-3700) serial port at the specified
> + address. The serial port must already be setup and
> + configured. Options are not yet supported.
> +
> earlyprintk= [X86,SH,BLACKFIN,ARM,M68k]
> earlyprintk=vga
> earlyprintk=efi
> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> index 39721ec4f415..b291f934d51b 100644
> --- a/drivers/tty/serial/Kconfig
> +++ b/drivers/tty/serial/Kconfig
> @@ -1606,6 +1606,28 @@ config SERIAL_STM32_CONSOLE
> depends on SERIAL_STM32=y
> select SERIAL_CORE_CONSOLE
>
> +config SERIAL_MVEBU_UART
> + bool "Marvell EBU serial port support"
> + select SERIAL_CORE
> + help
> + This driver is for Marvell EBU SoC's UART. If you have a machine
> + based on the Armada-3700 SoC and wish to use the on-board serial
> + port,
> + say 'Y' here.
> + Otherwise, say 'N'.
> +
> +config SERIAL_MVEBU_CONSOLE
> + bool "Console on Marvell EBU serial port"
> + depends on SERIAL_MVEBU_UART
> + select SERIAL_CORE_CONSOLE
> + select SERIAL_EARLYCON
> + default y
> + help
> + Say 'Y' here if you wish to use Armada-3700 UART as the system console.
> + (the system console is the device which receives all kernel messages
> + and warnings and which allows logins in single user mode)
> + Otherwise, say 'N'.
> +
> endmenu
>
> config SERIAL_MCTRL_GPIO
> diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
> index b391c9b31960..988167595330 100644
> --- a/drivers/tty/serial/Makefile
> +++ b/drivers/tty/serial/Makefile
> @@ -91,6 +91,7 @@ obj-$(CONFIG_SERIAL_CONEXANT_DIGICOLOR) += digicolor-usart.o
> obj-$(CONFIG_SERIAL_MEN_Z135) += men_z135_uart.o
> obj-$(CONFIG_SERIAL_SPRD) += sprd_serial.o
> obj-$(CONFIG_SERIAL_STM32) += stm32-usart.o
> +obj-$(CONFIG_SERIAL_MVEBU_UART) += mvebu-uart.o
>
> # GPIOLIB helpers for modem control lines
> obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o
> diff --git a/drivers/tty/serial/mvebu-uart.c b/drivers/tty/serial/mvebu-uart.c
> new file mode 100644
> index 000000000000..9624070d6058
> --- /dev/null
> +++ b/drivers/tty/serial/mvebu-uart.c
> @@ -0,0 +1,649 @@
> +/*
> +* ***************************************************************************
> +* Copyright (C) 2015 Marvell International Ltd.
> +* ***************************************************************************
> +* This program is free software: you can redistribute it and/or modify it
> +* under the terms of the GNU General Public License as published by the Free
> +* Software Foundation, either version 2 of the License, or any later version.
> +*
> +* This program is distributed in the hope that it will be useful,
> +* but WITHOUT ANY WARRANTY; without even the implied warranty of
> +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +* GNU General Public License for more details.
> +*
> +* You should have received a copy of the GNU General Public License
> +* along with this program. If not, see <http://www.gnu.org/licenses/>.
> +* ***************************************************************************
> +*/
> +
> +#include <linux/clk.h>
> +#include <linux/console.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/init.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/of_device.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_platform.h>
> +#include <linux/platform_device.h>
> +#include <linux/serial.h>
> +#include <linux/serial_core.h>
> +#include <linux/slab.h>
> +#include <linux/tty.h>
> +#include <linux/tty_flip.h>
> +
> +/* Register Map */
> +#define UART_RBR 0x00
> +#define RBR_BRK_DET BIT(15)
> +#define RBR_FRM_ERR_DET BIT(14)
> +#define RBR_PAR_ERR_DET BIT(13)
> +#define RBR_OVR_ERR_DET BIT(12)
> +
> +#define UART_TSH 0x04
> +
> +#define UART_CTRL 0x08
> +#define CTRL_SOFT_RST BIT(31)
> +#define CTRL_TXFIFO_RST BIT(15)
> +#define CTRL_RXFIFO_RST BIT(14)
> +#define CTRL_ST_MIRR_EN BIT(13)
> +#define CTRL_LPBK_EN BIT(12)
> +#define CTRL_SND_BRK_SEQ BIT(11)
> +#define CTRL_PAR_EN BIT(10)
> +#define CTRL_TWO_STOP BIT(9)
> +#define CTRL_TX_HFL_INT BIT(8)
> +#define CTRL_RX_HFL_INT BIT(7)
> +#define CTRL_TX_EMP_INT BIT(6)
> +#define CTRL_TX_RDY_INT BIT(5)
> +#define CTRL_RX_RDY_INT BIT(4)
> +#define CTRL_BRK_DET_INT BIT(3)
> +#define CTRL_FRM_ERR_INT BIT(2)
> +#define CTRL_PAR_ERR_INT BIT(1)
> +#define CTRL_OVR_ERR_INT BIT(0)
> +#define CTRL_RX_INT (CTRL_RX_RDY_INT | CTRL_BRK_DET_INT |\
> + CTRL_FRM_ERR_INT | CTRL_PAR_ERR_INT | CTRL_OVR_ERR_INT)
> +
> +#define UART_STAT 0x0c
> +#define STAT_TX_FIFO_EMP BIT(13)
> +#define STAT_RX_FIFO_EMP BIT(12)
> +#define STAT_TX_FIFO_FUL BIT(11)
> +#define STAT_TX_FIFO_HFL BIT(10)
> +#define STAT_RX_TOGL BIT(9)
> +#define STAT_RX_FIFO_FUL BIT(8)
> +#define STAT_RX_FIFO_HFL BIT(7)
> +#define STAT_TX_EMP BIT(6)
> +#define STAT_TX_RDY BIT(5)
> +#define STAT_RX_RDY BIT(4)
> +#define STAT_BRK_DET BIT(3)
> +#define STAT_FRM_ERR BIT(2)
> +#define STAT_PAR_ERR BIT(1)
> +#define STAT_OVR_ERR BIT(0)
> +#define STAT_BRK_ERR (STAT_BRK_DET | STAT_FRM_ERR | STAT_FRM_ERR\
> + | STAT_PAR_ERR | STAT_OVR_ERR)
> +
> +#define UART_BRDV 0x10
> +
> +#define MVEBU_NR_UARTS 1
> +
> +#define MVEBU_UART_TYPE "mvebu-uart"
> +
> +static struct uart_port mvebu_uart_ports[MVEBU_NR_UARTS];
> +
> +struct mvebu_uart_data {
> + struct uart_port *port;
> + struct clk *clk;
> +};
> +
> +/* Core UART Driver Operations */
> +static unsigned int mvebu_uart_tx_empty(struct uart_port *port)
> +{
> + unsigned long flags;
> + unsigned int st;
> +
> + spin_lock_irqsave(&port->lock, flags);
> + st = readl(port->membase + UART_STAT);
> + spin_unlock_irqrestore(&port->lock, flags);
> +
> + return (st & STAT_TX_FIFO_EMP) ? TIOCSER_TEMT : 0;
> +}
> +
> +static unsigned int mvebu_uart_get_mctrl(struct uart_port *port)
> +{
> + return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
> +}
> +
> +static void mvebu_uart_set_mctrl(struct uart_port *port,
> + unsigned int mctrl)
> +{
> +/*
> + * Even if we do not support configuring the modem control lines, this
> + * function must be proided to the serial core
> + */
> +}
> +
> +static void mvebu_uart_stop_tx(struct uart_port *port)
> +{
> + unsigned int ctl = readl(port->membase + UART_CTRL);
> +
> + ctl &= ~CTRL_TX_RDY_INT;
> + writel(ctl, port->membase + UART_CTRL);
> +}
> +
> +static void mvebu_uart_start_tx(struct uart_port *port)
> +{
> + unsigned int ctl = readl(port->membase + UART_CTRL);
> +
> + ctl |= CTRL_TX_RDY_INT;
> + writel(ctl, port->membase + UART_CTRL);
> +}
> +
> +static void mvebu_uart_stop_rx(struct uart_port *port)
> +{
> + unsigned int ctl = readl(port->membase + UART_CTRL);
> +
> + ctl &= ~CTRL_RX_INT;
> + writel(ctl, port->membase + UART_CTRL);
> +}
> +
> +static void mvebu_uart_break_ctl(struct uart_port *port, int brk)
> +{
> + unsigned int ctl;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&port->lock, flags);
> + ctl = readl(port->membase + UART_CTRL);
> + if (brk == -1)
> + ctl |= CTRL_SND_BRK_SEQ;
> + else
> + ctl &= ~CTRL_SND_BRK_SEQ;
> + writel(ctl, port->membase + UART_CTRL);
> + spin_unlock_irqrestore(&port->lock, flags);
> +}
> +
> +static void mvebu_uart_rx_chars(struct uart_port *port, unsigned int status)
> +{
> + struct tty_port *tport = &port->state->port;
> + unsigned char ch = 0;
> + char flag = 0;
> +
> + do {
> + if (status & STAT_RX_RDY) {
> + ch = readl(port->membase + UART_RBR);
> + ch &= 0xff;
> + flag = TTY_NORMAL;
> + port->icount.rx++;
> +
> + if (status & STAT_PAR_ERR)
> + port->icount.parity++;
> + }
> +
> + if (status & STAT_BRK_DET) {
> + port->icount.brk++;
> + status &= ~(STAT_FRM_ERR | STAT_PAR_ERR);
> + if (uart_handle_break(port))
> + goto ignore_char;
> + }
> +
> + if (status & STAT_OVR_ERR)
> + port->icount.overrun++;
> +
> + if (status & STAT_FRM_ERR)
> + port->icount.frame++;
> +
> + if (uart_handle_sysrq_char(port, ch))
> + goto ignore_char;
> +
> + if (status & port->ignore_status_mask & STAT_PAR_ERR)
> + status &= ~STAT_RX_RDY;
> +
> + status &= port->read_status_mask;
> +
> + if (status & STAT_PAR_ERR)
> + flag = TTY_PARITY;
> +
> + status &= ~port->ignore_status_mask;
> +
> + if (status & STAT_RX_RDY)
> + tty_insert_flip_char(tport, ch, flag);
> +
> + if (status & STAT_BRK_DET)
> + tty_insert_flip_char(tport, 0, TTY_BREAK);
> +
> + if (status & STAT_FRM_ERR)
> + tty_insert_flip_char(tport, 0, TTY_FRAME);
> +
> + if (status & STAT_OVR_ERR)
> + tty_insert_flip_char(tport, 0, TTY_OVERRUN);
> +
> +ignore_char:
> + status = readl(port->membase + UART_STAT);
> + } while (status & (STAT_RX_RDY | STAT_BRK_DET));
> +
> + tty_flip_buffer_push(tport);
> +}
> +
> +static void mvebu_uart_tx_chars(struct uart_port *port, unsigned int status)
> +{
> + struct circ_buf *xmit = &port->state->xmit;
> + unsigned int count;
> + unsigned int st;
> +
> + if (port->x_char) {
> + writel(port->x_char, port->membase + UART_TSH);
> + port->icount.tx++;
> + port->x_char = 0;
> + return;
> + }
> +
> + if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
> + mvebu_uart_stop_tx(port);
> + return;
> + }
> +
> + for (count = 0; count < port->fifosize; count++) {
> + writel(xmit->buf[xmit->tail], port->membase + UART_TSH);
> + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
> + port->icount.tx++;
> +
> + if (uart_circ_empty(xmit))
> + break;
> +
> + st = readl(port->membase + UART_STAT);
> + if (st & STAT_TX_FIFO_FUL)
> + break;
> + }
> +
> + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
> + uart_write_wakeup(port);
> +
> + if (uart_circ_empty(xmit))
> + mvebu_uart_stop_tx(port);
> +}
> +
> +static irqreturn_t mvebu_uart_isr(int irq, void *dev_id)
> +{
> + struct uart_port *port = (struct uart_port *)dev_id;
> + unsigned int st = readl(port->membase + UART_STAT);
> +
> + if (st & (STAT_RX_RDY | STAT_OVR_ERR | STAT_FRM_ERR | STAT_BRK_DET))
> + mvebu_uart_rx_chars(port, st);
> +
> + if (st & STAT_TX_RDY)
> + mvebu_uart_tx_chars(port, st);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int mvebu_uart_startup(struct uart_port *port)
> +{
> + int ret;
> +
> + writel(CTRL_TXFIFO_RST | CTRL_RXFIFO_RST,
> + port->membase + UART_CTRL);
> + udelay(1);
> + writel(CTRL_RX_INT, port->membase + UART_CTRL);
> +
> + ret = request_irq(port->irq, mvebu_uart_isr, port->irqflags, "serial",
> + port);
> + if (ret) {
> + dev_err(port->dev, "failed to request irq\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static void mvebu_uart_shutdown(struct uart_port *port)
> +{
> + writel(0, port->membase + UART_CTRL);
> +}
> +
> +static void mvebu_uart_set_termios(struct uart_port *port,
> + struct ktermios *termios,
> + struct ktermios *old)
> +{
> + unsigned long flags;
> + unsigned int baud;
> +
> + spin_lock_irqsave(&port->lock, flags);
> +
> + port->read_status_mask = STAT_RX_RDY | STAT_OVR_ERR |
> + STAT_TX_RDY | STAT_TX_FIFO_FUL;
> +
> + if (termios->c_iflag & INPCK)
> + port->read_status_mask |= STAT_FRM_ERR | STAT_PAR_ERR;
> +
> + port->ignore_status_mask = 0;
> + if (termios->c_iflag & IGNPAR)
> + port->ignore_status_mask |=
> + STAT_FRM_ERR | STAT_PAR_ERR | STAT_OVR_ERR;
> +
> + if ((termios->c_cflag & CREAD) == 0)
> + port->ignore_status_mask |= STAT_RX_RDY | STAT_BRK_ERR;
> +
> + baud = uart_get_baud_rate(port, termios, old, 0, 460800);
> + uart_update_timeout(port, termios->c_cflag, baud);
> +
> + spin_unlock_irqrestore(&port->lock, flags);
> +}
> +
> +static const char *mvebu_uart_type(struct uart_port *port)
> +{
> + return MVEBU_UART_TYPE;
> +}
> +
> +static void mvebu_uart_release_port(struct uart_port *port)
> +{
> + /* Nothing to do here */
> +}
> +
> +static int mvebu_uart_request_port(struct uart_port *port)
> +{
> + return 0;
> +}
> +
> +#ifdef CONFIG_CONSOLE_POLL
> +static int mvebu_uart_get_poll_char(struct uart_port *port)
> +{
> + unsigned int st = readl(port->membase + UART_STAT);
> +
> + if (!(st & STAT_RX_RDY))
> + return NO_POLL_CHAR;
> +
> + return readl(port->membase + UART_RBR);
> +}
> +
> +static void mvebu_uart_put_poll_char(struct uart_port *port, unsigned char c)
> +{
> + unsigned int st;
> +
> + for (;;) {
> + st = readl(port->membase + UART_STAT);
> +
> + if (!(st & STAT_TX_FIFO_FUL))
> + break;
> +
> + udelay(1);
> + }
> +
> + writel(c, port->membase + UART_TSH);
> +}
> +#endif
> +
> +static const struct uart_ops mvebu_uart_ops = {
> + .tx_empty = mvebu_uart_tx_empty,
> + .set_mctrl = mvebu_uart_set_mctrl,
> + .get_mctrl = mvebu_uart_get_mctrl,
> + .stop_tx = mvebu_uart_stop_tx,
> + .start_tx = mvebu_uart_start_tx,
> + .stop_rx = mvebu_uart_stop_rx,
> + .break_ctl = mvebu_uart_break_ctl,
> + .startup = mvebu_uart_startup,
> + .shutdown = mvebu_uart_shutdown,
> + .set_termios = mvebu_uart_set_termios,
> + .type = mvebu_uart_type,
> + .release_port = mvebu_uart_release_port,
> + .request_port = mvebu_uart_request_port,
> +#ifdef CONFIG_CONSOLE_POLL
> + .poll_get_char = mvebu_uart_get_poll_char,
> + .poll_put_char = mvebu_uart_put_poll_char,
> +#endif
> +};
> +
> +/* Console Driver Operations */
> +
> +#ifdef CONFIG_SERIAL_MVEBU_CONSOLE
> +/* Early Console */
> +static void mvebu_uart_putc(struct uart_port *port, int c)
> +{
> + unsigned int st;
> +
> + for (;;) {
> + st = readl(port->membase + UART_STAT);
> + if (!(st & STAT_TX_FIFO_FUL))
> + break;
> + }
> +
> + writel(c, port->membase + UART_TSH);
> +
> + for (;;) {
> + st = readl(port->membase + UART_STAT);
> + if (st & STAT_TX_FIFO_EMP)
> + break;
> + }
> +}
> +
> +static void mvebu_uart_putc_early_write(struct console *con,
> + const char *s,
> + unsigned n)
> +{
> + struct earlycon_device *dev = con->data;
> +
> + uart_console_write(&dev->port, s, n, mvebu_uart_putc);
> +}
> +
> +static int __init
> +mvebu_uart_early_console_setup(struct earlycon_device *device,
> + const char *opt)
> +{
> + if (!device->port.membase)
> + return -ENODEV;
> +
> + device->con->write = mvebu_uart_putc_early_write;
> +
> + return 0;
> +}
> +
> +EARLYCON_DECLARE(ar3700_uart, mvebu_uart_early_console_setup);
> +OF_EARLYCON_DECLARE(ar3700_uart, "marvell,armada-3700-uart",
> + mvebu_uart_early_console_setup);
> +
> +static void wait_for_xmitr(struct uart_port *port)
> +{
> + u32 val;
> +
> + readl_poll_timeout_atomic(port->membase + UART_STAT, val,
> + (val & STAT_TX_EMP), 1, 10000);
> +}
> +
> +static void mvebu_uart_console_putchar(struct uart_port *port, int ch)
> +{
> + wait_for_xmitr(port);
> + writel(ch, port->membase + UART_TSH);
> +}
> +
> +static void mvebu_uart_console_write(struct console *co, const char *s,
> + unsigned int count)
> +{
> + struct uart_port *port = &mvebu_uart_ports[co->index];
> + unsigned long flags;
> + unsigned int ier;
> + int locked = 1;
> +
> + if (oops_in_progress)
> + locked = spin_trylock_irqsave(&port->lock, flags);
> + else
> + spin_lock_irqsave(&port->lock, flags);
> +
> + ier = readl(port->membase + UART_CTRL) &
> + (CTRL_RX_INT | CTRL_TX_RDY_INT);
> + writel(0, port->membase + UART_CTRL);
> +
> + uart_console_write(port, s, count, mvebu_uart_console_putchar);
> +
> + wait_for_xmitr(port);
> +
> + if (ier)
> + writel(ier, port->membase + UART_CTRL);
> +
> + if (locked)
> + spin_unlock_irqrestore(&port->lock, flags);
> +}
> +
> +static int mvebu_uart_console_setup(struct console *co, char *options)
> +{
> + struct uart_port *port;
> + int baud = 9600;
> + int bits = 8;
> + int parity = 'n';
> + int flow = 'n';
> +
> + if (co->index < 0 || co->index >= MVEBU_NR_UARTS)
> + return -EINVAL;
> +
> + port = &mvebu_uart_ports[co->index];
> +
> + if (!port->mapbase || !port->membase) {
> + pr_debug("console on ttyS%i not present\n", co->index);
> + return -ENODEV;
> + }
> +
> + if (options)
> + uart_parse_options(options, &baud, &parity, &bits, &flow);
> +
> + return uart_set_options(port, co, baud, parity, bits, flow);
> +}
> +
> +static struct uart_driver mvebu_uart_driver;
> +
> +static struct console mvebu_uart_console = {
> + .name = "ttyS",
> + .write = mvebu_uart_console_write,
> + .device = uart_console_device,
> + .setup = mvebu_uart_console_setup,
> + .flags = CON_PRINTBUFFER,
> + .index = -1,
> + .data = &mvebu_uart_driver,
> +};
> +
> +static int __init mvebu_uart_console_init(void)
> +{
> + register_console(&mvebu_uart_console);
> + return 0;
> +}
> +
> +console_initcall(mvebu_uart_console_init);
> +
> +
> +#endif /* CONFIG_SERIAL_MVEBU_CONSOLE */
> +
> +static struct uart_driver mvebu_uart_driver = {
> + .owner = THIS_MODULE,
> + .driver_name = "serial",
> + .dev_name = "ttyS",
> + .major = TTY_MAJOR,
> + .minor = 64,
> + .nr = MVEBU_NR_UARTS,
> +#ifdef CONFIG_SERIAL_MVEBU_CONSOLE
> + .cons = &mvebu_uart_console,
> +#endif
> +};
> +
> +static int mvebu_uart_probe(struct platform_device *pdev)
> +{
> + struct resource *reg = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + struct resource *irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
> + struct uart_port *port;
> + struct mvebu_uart_data *data;
> + int ret;
> +
> + if (!reg || !irq) {
> + dev_err(&pdev->dev, "no registers/irq defined\n");
> + return -EINVAL;
> + }
> +
> + port = &mvebu_uart_ports[0];
> +
> + spin_lock_init(&port->lock);
> +
> + port->dev = &pdev->dev;
> + port->type = PORT_MVEBU;
> + port->ops = &mvebu_uart_ops;
> + port->regshift = 0;
> +
> + port->fifosize = 32;
> + port->iotype = UPIO_MEM32;
> + port->flags = UPF_FIXED_PORT;
> + port->line = 0; /* single port: force line number to 0 */
> +
> + port->irq = irq->start;
> + port->irqflags = 0;
> + port->mapbase = reg->start;
> +
> + port->membase = devm_ioremap_resource(&pdev->dev, reg);
> + if (IS_ERR(port->membase))
> + return -PTR_ERR(port->membase);
> +
> + data = devm_kzalloc(&pdev->dev, sizeof(struct mvebu_uart_data),
> + GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> +
> + data->port = port;
> +
> + port->private_data = data;
> + platform_set_drvdata(pdev, data);
> +
> + ret = uart_add_one_port(&mvebu_uart_driver, port);
> + if (ret)
> + return ret;
> + return 0;
> +}
> +
> +static int mvebu_uart_remove(struct platform_device *pdev)
> +{
> + struct mvebu_uart_data *data = platform_get_drvdata(pdev);
> +
> + uart_remove_one_port(&mvebu_uart_driver, data->port);
> + data->port->private_data = NULL;
> + data->port->mapbase = 0;
> + return 0;
> +}
> +
> +/* Match table for of_platform binding */
> +static const struct of_device_id mvebu_uart_of_match[] = {
> + { .compatible = "marvell,armada-3700-uart", },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, mvebu_uart_of_match);
> +
> +static struct platform_driver mvebu_uart_platform_driver = {
> + .probe = mvebu_uart_probe,
> + .remove = mvebu_uart_remove,
> + .driver = {
> + .owner = THIS_MODULE,
> + .name = "mvebu-uart",
> + .of_match_table = of_match_ptr(mvebu_uart_of_match),
> + },
> +};
> +
> +static int __init mvebu_uart_init(void)
> +{
> + int ret;
> +
> + ret = uart_register_driver(&mvebu_uart_driver);
> + if (ret)
> + return ret;
> +
> + ret = platform_driver_register(&mvebu_uart_platform_driver);
> + if (ret)
> + uart_unregister_driver(&mvebu_uart_driver);
> +
> + return ret;
> +}
> +
> +static void __exit mvebu_uart_exit(void)
> +{
> + platform_driver_unregister(&mvebu_uart_platform_driver);
> + uart_unregister_driver(&mvebu_uart_driver);
> +}
> +
> +arch_initcall(mvebu_uart_init);
> +module_exit(mvebu_uart_exit);
> +
> +MODULE_AUTHOR("Wilson Ding <dingwei@xxxxxxxxxxx>");
> +MODULE_DESCRIPTION("Marvell Armada-3700 Serial Driver");
> +MODULE_LICENSE("GPL");
> diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
> index 3e5d757407fb..e513a4ee369b 100644
> --- a/include/uapi/linux/serial_core.h
> +++ b/include/uapi/linux/serial_core.h
> @@ -261,4 +261,7 @@
> /* STM32 USART */
> #define PORT_STM32 113
>
> +/* MVEBU UART */
> +#define PORT_MVEBU 114
> +
> #endif /* _UAPILINUX_SERIAL_CORE_H */
> --
> 2.5.0
>