[PATCH v2 13/22] ncr5380: Remove disused atari_NCR5380.c core driver

From: Finn Thain
Date: Tue Mar 15 2016 - 23:33:37 EST

Now that atari_scsi and sun3_scsi have been converted to use the NCR5380.c
core driver, remove atari_NCR5380.c. Also remove the last vestiges of its
Tagged Command Queueing implementation from the wrapper drivers.

The TCQ support in atari_NCR5380.c is abandoned by this patch. It is not
merged into the remaining core driver because,

1) atari_scsi defines SUPPORT_TAGS but leaves FLAG_TAGGED_QUEUING disabled
by default, which indicates that it is mostly undesirable.

2) I'm told that it doesn't work correctly when enabled.

3) The algorithm does not make use of block layer tags which it will have
to do because scmd->tag is deprecated.

4) sun3_scsi doesn't define SUPPORT_TAGS at all, yet the the SUPPORT_TAGS
macro interacts with the CONFIG_SUN3 macro in 'interesting' ways.

5) Compile-time configuration with macros like SUPPORT_TAGS caused the
configuration space to explode, leading to untestable and unmaintainable
code that is too hard to reason about.

The merge_contiguous_buffers() code is also abandoned. This was unused
by sun3_scsi. Only atari_scsi used it and then only on TT, because only TT
supports scatter/gather. I suspect that the TT would work fine with
ENABLE_CLUSTERING instead. If someone can benchmark the difference then
perhaps the merge_contiguous_buffers() code can be be justified. Until
then we are better off without the extra complexity.

Signed-off-by: Finn Thain <fthain@xxxxxxxxxxxxxxxxxxx>
Reviewed-by: Hannes Reinecke <hare@xxxxxxxx>

---
drivers/scsi/NCR5380.c | 22
drivers/scsi/NCR5380.h | 19
drivers/scsi/atari_NCR5380.c | 2632 -------------------------------------------
drivers/scsi/atari_scsi.c | 11
drivers/scsi/mac_scsi.c | 8
drivers/scsi/sun3_scsi.c | 11
6 files changed, 4 insertions(+), 2699 deletions(-)

Index: linux/drivers/scsi/atari_scsi.c
===================================================================
--- linux.orig/drivers/scsi/atari_scsi.c 2016-03-16 14:18:24.000000000 +1100
+++ linux/drivers/scsi/atari_scsi.c 2016-03-16 14:18:27.000000000 +1100
@@ -87,9 +87,6 @@

/* Definitions for the core NCR5380 driver. */

-#define SUPPORT_TAGS
-#define MAX_TAGS 32
-
#define NCR5380_implementation_fields /* none */

#define NCR5380_read(reg) atari_scsi_reg_read(reg)
@@ -189,8 +186,6 @@ static int setup_cmd_per_lun = -1;
module_param(setup_cmd_per_lun, int, 0);
static int setup_sg_tablesize = -1;
module_param(setup_sg_tablesize, int, 0);
-static int setup_use_tagged_queuing = -1;
-module_param(setup_use_tagged_queuing, int, 0);
static int setup_hostid = -1;
module_param(setup_hostid, int, 0);
static int setup_toshiba_delay = -1;
@@ -479,8 +474,7 @@ static int __init atari_scsi_setup(char
setup_sg_tablesize = ints[3];
if (ints[0] >= 4)
setup_hostid = ints[4];
- if (ints[0] >= 5)
- setup_use_tagged_queuing = ints[5];
+ /* ints[5] (use_tagged_queuing) is ignored */
/* ints[6] (use_pdma) is ignored */
if (ints[0] >= 7)
setup_toshiba_delay = ints[7];
@@ -853,9 +847,6 @@ static int __init atari_scsi_probe(struc
instance->irq = irq->start;

host_flags |= IS_A_TT() ? 0 : FLAG_LATE_DMA_SETUP;
-#ifdef SUPPORT_TAGS
- host_flags |= setup_use_tagged_queuing > 0 ? FLAG_TAGGED_QUEUING : 0;
-#endif
host_flags |= setup_toshiba_delay > 0 ? FLAG_TOSHIBA_DELAY : 0;

error = NCR5380_init(instance, host_flags);
Index: linux/drivers/scsi/sun3_scsi.c
===================================================================
--- linux.orig/drivers/scsi/sun3_scsi.c 2016-03-16 14:18:25.000000000 +1100
+++ linux/drivers/scsi/sun3_scsi.c 2016-03-16 14:18:27.000000000 +1100
@@ -41,9 +41,6 @@

/* Definitions for the core NCR5380 driver. */

-/* #define SUPPORT_TAGS */
-/* #define MAX_TAGS 32 */
-
#define NCR5380_implementation_fields /* none */

#define NCR5380_read(reg) sun3scsi_read(reg)
@@ -75,10 +72,6 @@ static int setup_cmd_per_lun = -1;
module_param(setup_cmd_per_lun, int, 0);
static int setup_sg_tablesize = -1;
module_param(setup_sg_tablesize, int, 0);
-#ifdef SUPPORT_TAGS
-static int setup_use_tagged_queuing = -1;
-module_param(setup_use_tagged_queuing, int, 0);
-#endif
static int setup_hostid = -1;
module_param(setup_hostid, int, 0);

@@ -512,10 +505,6 @@ static int __init sun3_scsi_probe(struct
instance->io_port = (unsigned long)ioaddr;
instance->irq = irq->start;

-#ifdef SUPPORT_TAGS
- host_flags |= setup_use_tagged_queuing > 0 ? FLAG_TAGGED_QUEUING : 0;
-#endif
-
error = NCR5380_init(instance, host_flags);
if (error)
goto fail_init;
Index: linux/drivers/scsi/mac_scsi.c
===================================================================
--- linux.orig/drivers/scsi/mac_scsi.c 2016-03-16 14:18:20.000000000 +1100
+++ linux/drivers/scsi/mac_scsi.c 2016-03-16 14:18:27.000000000 +1100
@@ -55,8 +55,6 @@ static int setup_sg_tablesize = -1;
module_param(setup_sg_tablesize, int, 0);
static int setup_use_pdma = -1;
module_param(setup_use_pdma, int, 0);
-static int setup_use_tagged_queuing = -1;
-module_param(setup_use_tagged_queuing, int, 0);
static int setup_hostid = -1;
module_param(setup_hostid, int, 0);
static int setup_toshiba_delay = -1;
@@ -95,8 +93,7 @@ static int __init mac_scsi_setup(char *s
setup_sg_tablesize = ints[3];
if (ints[0] >= 4)
setup_hostid = ints[4];
- if (ints[0] >= 5)
- setup_use_tagged_queuing = ints[5];
+ /* ints[5] (use_tagged_queuing) is ignored */
if (ints[0] >= 6)
setup_use_pdma = ints[6];
if (ints[0] >= 7)
@@ -382,9 +379,6 @@ static int __init mac_scsi_probe(struct
} else
host_flags |= FLAG_NO_PSEUDO_DMA;

-#ifdef SUPPORT_TAGS
- host_flags |= setup_use_tagged_queuing > 0 ? FLAG_TAGGED_QUEUING : 0;
-#endif
host_flags |= setup_toshiba_delay > 0 ? FLAG_TOSHIBA_DELAY : 0;

error = NCR5380_init(instance, host_flags | FLAG_LATE_DMA_SETUP);
Index: linux/drivers/scsi/NCR5380.c
===================================================================
--- linux.orig/drivers/scsi/NCR5380.c 2016-03-16 14:18:25.000000000 +1100
+++ linux/drivers/scsi/NCR5380.c 2016-03-16 14:18:27.000000000 +1100
@@ -34,13 +34,6 @@
/* Adapted for the Sun 3 by Sam Creasey. */

/*
- * Further development / testing that should be done :
- *
- * 4. Test SCSI-II tagged queueing (I have no devices which support
- * tagged queueing)
- */
-
-/*
* Design
*
* This is a generic 5380 driver. To use it on a different platform,
@@ -1257,14 +1250,6 @@ static struct scsi_cmnd *NCR5380_select(
* was true but before BSY was false during selection, the information
* transfer phase should be a MESSAGE OUT phase so that we can send the
* IDENTIFY message.
- *
- * If SCSI-II tagged queuing is enabled, we also send a SIMPLE_QUEUE_TAG
- * message (2 bytes) with a tag ID that we increment with every command
- * until it wraps back to 0.
- *
- * XXX - it turns out that there are some broken SCSI-II devices,
- * which claim to support tagged queuing but fail when more than
- * some number of commands are issued at once.
*/

/* Wait for start of REQ/ACK handshake */
@@ -1287,9 +1272,6 @@ static struct scsi_cmnd *NCR5380_select(
tmp[0] = IDENTIFY(((instance->irq == NO_IRQ) ? 0 : 1), cmd->device->lun);

len = 1;
- cmd->tag = 0;
-
- /* Send message(s) */
data = tmp;
phase = PHASE_MSGOUT;
NCR5380_transfer_pio(instance, &phase, &len, &data);
@@ -2256,8 +2238,8 @@ static void NCR5380_reselect(struct Scsi
NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);

hostdata->connected = tmp;
- dsprintk(NDEBUG_RESELECTION, instance, "nexus established, target %d, lun %llu, tag %d\n",
- scmd_id(tmp), tmp->device->lun, tmp->tag);
+ dsprintk(NDEBUG_RESELECTION, instance, "nexus established, target %d, lun %llu\n",
+ scmd_id(tmp), tmp->device->lun);
}

/**
Index: linux/drivers/scsi/NCR5380.h
===================================================================
--- linux.orig/drivers/scsi/NCR5380.h 2016-03-16 14:18:11.000000000 +1100
+++ linux/drivers/scsi/NCR5380.h 2016-03-16 14:18:27.000000000 +1100
@@ -199,13 +199,6 @@

#define PHASE_SR_TO_TCR(phase) ((phase) >> 2)

-/*
- * "Special" value for the (unsigned char) command tag, to indicate
- * I_T_L nexus instead of I_T_L_Q.
- */
-
-#define TAG_NONE 0xff
-
/*
* These are "special" values for the irq and dma_channel fields of the
* Scsi_Host structure
@@ -223,17 +216,8 @@
#define FLAG_DMA_FIXUP 1 /* Use DMA errata workarounds */
#define FLAG_NO_PSEUDO_DMA 8 /* Inhibit DMA */
#define FLAG_LATE_DMA_SETUP 32 /* Setup NCR before DMA H/W */
-#define FLAG_TAGGED_QUEUING 64 /* as X3T9.2 spelled it */
#define FLAG_TOSHIBA_DELAY 128 /* Allow for borken CD-ROMs */

-#ifdef SUPPORT_TAGS
-struct tag_alloc {
- DECLARE_BITMAP(allocated, MAX_TAGS);
- int nr_allocated;
- int queue_size;
-};
-#endif
-
struct NCR5380_hostdata {
NCR5380_implementation_fields; /* implementation specific */
struct Scsi_Host *host; /* Host backpointer */
@@ -254,9 +238,6 @@ struct NCR5380_hostdata {
int read_overruns; /* number of bytes to cut from a
* transfer to handle chip overruns */
struct work_struct main_task;
-#ifdef SUPPORT_TAGS
- struct tag_alloc TagAlloc[8][8]; /* 8 targets and 8 LUNs */
-#endif
struct workqueue_struct *work_q;
unsigned long accesses_per_ms; /* chip register accesses per ms */
};
Index: linux/drivers/scsi/atari_NCR5380.c
===================================================================
--- linux.orig/drivers/scsi/atari_NCR5380.c 2016-03-16 14:18:07.000000000 +1100
+++ /dev/null 1970-01-01 00:00:00.000000000 +0000
@@ -1,2632 +0,0 @@
-/*
- * NCR 5380 generic driver routines. These should make it *trivial*
- * to implement 5380 SCSI drivers under Linux with a non-trantor
- * architecture.
- *
- * Note that these routines also work with NR53c400 family chips.
- *
- * Copyright 1993, Drew Eckhardt
- * Visionary Computing
- * (Unix and Linux consulting and custom programming)
- * drew@xxxxxxxxxxxx
- * +1 (303) 666-5836
- *
- * For more information, please consult
- *
- * NCR 5380 Family
- * SCSI Protocol Controller
- * Databook
- *
- * NCR Microelectronics
- * 1635 Aeroplaza Drive
- * Colorado Springs, CO 80916
- * 1+ (719) 578-3400
- * 1+ (800) 334-5454
- */
-
-/* Ported to Atari by Roman Hodek and others. */
-
-/* Adapted for the sun3 by Sam Creasey. */
-
-/*
- * Design
- *
- * This is a generic 5380 driver. To use it on a different platform,
- * one simply writes appropriate system specific macros (ie, data
- * transfer - some PC's will use the I/O bus, 68K's must use
- * memory mapped) and drops this file in their 'C' wrapper.
- *
- * As far as command queueing, two queues are maintained for
- * each 5380 in the system - commands that haven't been issued yet,
- * and commands that are currently executing. This means that an
- * unlimited number of commands may be queued, letting
- * more commands propagate from the higher driver levels giving higher
- * throughput. Note that both I_T_L and I_T_L_Q nexuses are supported,
- * allowing multiple commands to propagate all the way to a SCSI-II device
- * while a command is already executing.
- *
- *
- * Issues specific to the NCR5380 :
- *
- * When used in a PIO or pseudo-dma mode, the NCR5380 is a braindead
- * piece of hardware that requires you to sit in a loop polling for
- * the REQ signal as long as you are connected. Some devices are
- * brain dead (ie, many TEXEL CD ROM drives) and won't disconnect
- * while doing long seek operations. [...] These
- * broken devices are the exception rather than the rule and I'd rather
- * spend my time optimizing for the normal case.
- *
- * Architecture :
- *
- * At the heart of the design is a coroutine, NCR5380_main,
- * which is started from a workqueue for each NCR5380 host in the
- * system. It attempts to establish I_T_L or I_T_L_Q nexuses by
- * removing the commands from the issue queue and calling
- * NCR5380_select() if a nexus is not established.
- *
- * Once a nexus is established, the NCR5380_information_transfer()
- * phase goes through the various phases as instructed by the target.
- * if the target goes into MSG IN and sends a DISCONNECT message,
- * the command structure is placed into the per instance disconnected
- * queue, and NCR5380_main tries to find more work. If the target is
- * idle for too long, the system will try to sleep.
- *
- * If a command has disconnected, eventually an interrupt will trigger,
- * calling NCR5380_intr() which will in turn call NCR5380_reselect
- * to reestablish a nexus. This will run main if necessary.
- *
- * On command termination, the done function will be called as
- * appropriate.
- *
- * SCSI pointers are maintained in the SCp field of SCSI command
- * structures, being initialized after the command is connected
- * in NCR5380_select, and set as appropriate in NCR5380_information_transfer.
- * Note that in violation of the standard, an implicit SAVE POINTERS operation
- * is done, since some BROKEN disks fail to issue an explicit SAVE POINTERS.
- */
-
-/*
- * Using this file :
- * This file a skeleton Linux SCSI driver for the NCR 5380 series
- * of chips. To use it, you write an architecture specific functions
- * and macros and include this file in your driver.
- *
- * These macros control options :
- * AUTOSENSE - if defined, REQUEST SENSE will be performed automatically
- * for commands that return with a CHECK CONDITION status.
- *
- * DIFFERENTIAL - if defined, NCR53c81 chips will use external differential
- * transceivers.
- *
- * REAL_DMA - if defined, REAL DMA is used during the data transfer phases.
- *
- * SUPPORT_TAGS - if defined, SCSI-2 tagged queuing is used where possible
- *
- * These macros MUST be defined :
- *
- * NCR5380_read(register) - read from the specified register
- *
- * NCR5380_write(register, value) - write to the specific register
- *
- * NCR5380_implementation_fields - additional fields needed for this
- * specific implementation of the NCR5380
- *
- * Either real DMA *or* pseudo DMA may be implemented
- * Note that the DMA setup functions should return the number of bytes
- * that they were able to program the controller for.
- *
- * NCR5380_dma_write_setup(instance, src, count) - initialize
- * NCR5380_dma_read_setup(instance, dst, count) - initialize
- * NCR5380_dma_residual(instance); - residual count
- *
- * PSEUDO functions :
- * NCR5380_pwrite(instance, src, count)
- * NCR5380_pread(instance, dst, count);
- *
- * The generic driver is initialized by calling NCR5380_init(instance),
- * after setting the appropriate host specific fields and ID. If the
- * driver wishes to autoprobe for an IRQ line, the NCR5380_probe_irq(instance,
- * possible) function may be used.
- */
-
-static int do_abort(struct Scsi_Host *);
-static void do_reset(struct Scsi_Host *);
-
-#ifdef SUPPORT_TAGS
-
-/*
- * Functions for handling tagged queuing
- * =====================================
- *
- * ++roman (01/96): Now I've implemented SCSI-2 tagged queuing. Some notes:
- *
- * Using consecutive numbers for the tags is no good idea in my eyes. There
- * could be wrong re-usings if the counter (8 bit!) wraps and some early
- * command has been preempted for a long time. My solution: a bitfield for
- * remembering used tags.
- *
- * There's also the problem that each target has a certain queue size, but we
- * cannot know it in advance :-( We just see a QUEUE_FULL status being
- * returned. So, in this case, the driver internal queue size assumption is
- * reduced to the number of active tags if QUEUE_FULL is returned by the
- * target.
- *
- * We're also not allowed running tagged commands as long as an untagged
- * command is active. And REQUEST SENSE commands after a contingent allegiance
- * condition _must_ be untagged. To keep track whether an untagged command has
- * been issued, the host->busy array is still employed, as it is without
- * support for tagged queuing.
- *
- * One could suspect that there are possible race conditions between
- * is_lun_busy(), cmd_get_tag() and cmd_free_tag(). But I think this isn't the
- * case: is_lun_busy() and cmd_get_tag() are both called from NCR5380_main(),
- * which already guaranteed to be running at most once. It is also the only
- * place where tags/LUNs are allocated. So no other allocation can slip
- * between that pair, there could only happen a reselection, which can free a
- * tag, but that doesn't hurt. Only the sequence in cmd_free_tag() becomes
- * important: the tag bit must be cleared before 'nr_allocated' is decreased.
- */
-
-static void __init init_tags(struct NCR5380_hostdata *hostdata)
-{
- int target, lun;
- struct tag_alloc *ta;
-
- if (!(hostdata->flags & FLAG_TAGGED_QUEUING))
- return;
-
- for (target = 0; target < 8; ++target) {
- for (lun = 0; lun < 8; ++lun) {
- ta = &hostdata->TagAlloc[target][lun];
- bitmap_zero(ta->allocated, MAX_TAGS);
- ta->nr_allocated = 0;
- /* At the beginning, assume the maximum queue size we could
- * support (MAX_TAGS). This value will be decreased if the target
- * returns QUEUE_FULL status.
- */
- ta->queue_size = MAX_TAGS;
- }
- }
-}
-
-
-/* Check if we can issue a command to this LUN: First see if the LUN is marked
- * busy by an untagged command. If the command should use tagged queuing, also
- * check that there is a free tag and the target's queue won't overflow. This
- * function should be called with interrupts disabled to avoid race
- * conditions.
- */
-
-static int is_lun_busy(struct scsi_cmnd *cmd, int should_be_tagged)
-{
- u8 lun = cmd->device->lun;
- struct Scsi_Host *instance = cmd->device->host;
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
- if (hostdata->busy[cmd->device->id] & (1 << lun))
- return 1;
- if (!should_be_tagged ||
- !(hostdata->flags & FLAG_TAGGED_QUEUING) ||
- !cmd->device->tagged_supported)
- return 0;
- if (hostdata->TagAlloc[scmd_id(cmd)][lun].nr_allocated >=
- hostdata->TagAlloc[scmd_id(cmd)][lun].queue_size) {
- dsprintk(NDEBUG_TAGS, instance, "target %d lun %d: no free tags\n",
- scmd_id(cmd), lun);
- return 1;
- }
- return 0;
-}
-
-
-/* Allocate a tag for a command (there are no checks anymore, check_lun_busy()
- * must be called before!), or reserve the LUN in 'busy' if the command is
- * untagged.
- */
-
-static void cmd_get_tag(struct scsi_cmnd *cmd, int should_be_tagged)
-{
- u8 lun = cmd->device->lun;
- struct Scsi_Host *instance = cmd->device->host;
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
- /* If we or the target don't support tagged queuing, allocate the LUN for
- * an untagged command.
- */
- if (!should_be_tagged ||
- !(hostdata->flags & FLAG_TAGGED_QUEUING) ||
- !cmd->device->tagged_supported) {
- cmd->tag = TAG_NONE;
- hostdata->busy[cmd->device->id] |= (1 << lun);
- dsprintk(NDEBUG_TAGS, instance, "target %d lun %d now allocated by untagged command\n",
- scmd_id(cmd), lun);
- } else {
- struct tag_alloc *ta = &hostdata->TagAlloc[scmd_id(cmd)][lun];
-
- cmd->tag = find_first_zero_bit(ta->allocated, MAX_TAGS);
- set_bit(cmd->tag, ta->allocated);
- ta->nr_allocated++;
- dsprintk(NDEBUG_TAGS, instance, "using tag %d for target %d lun %d (%d tags allocated)\n",
- cmd->tag, scmd_id(cmd), lun, ta->nr_allocated);
- }
-}
-
-
-/* Mark the tag of command 'cmd' as free, or in case of an untagged command,
- * unlock the LUN.
- */
-
-static void cmd_free_tag(struct scsi_cmnd *cmd)
-{
- u8 lun = cmd->device->lun;
- struct Scsi_Host *instance = cmd->device->host;
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
- if (cmd->tag == TAG_NONE) {
- hostdata->busy[cmd->device->id] &= ~(1 << lun);
- dsprintk(NDEBUG_TAGS, instance, "target %d lun %d untagged cmd freed\n",
- scmd_id(cmd), lun);
- } else if (cmd->tag >= MAX_TAGS) {
- shost_printk(KERN_NOTICE, instance,
- "trying to free bad tag %d!\n", cmd->tag);
- } else {
- struct tag_alloc *ta = &hostdata->TagAlloc[scmd_id(cmd)][lun];
- clear_bit(cmd->tag, ta->allocated);
- ta->nr_allocated--;
- dsprintk(NDEBUG_TAGS, instance, "freed tag %d for target %d lun %d\n",
- cmd->tag, scmd_id(cmd), lun);
- }
-}
-
-
-static void free_all_tags(struct NCR5380_hostdata *hostdata)
-{
- int target, lun;
- struct tag_alloc *ta;
-
- if (!(hostdata->flags & FLAG_TAGGED_QUEUING))
- return;
-
- for (target = 0; target < 8; ++target) {
- for (lun = 0; lun < 8; ++lun) {
- ta = &hostdata->TagAlloc[target][lun];
- bitmap_zero(ta->allocated, MAX_TAGS);
- ta->nr_allocated = 0;
- }
- }
-}
-
-#endif /* SUPPORT_TAGS */
-
-/**
- * merge_contiguous_buffers - coalesce scatter-gather list entries
- * @cmd: command requesting IO
- *
- * Try to merge several scatter-gather buffers into one DMA transfer.
- * This is possible if the scatter buffers lie on physically
- * contiguous addresses. The first scatter-gather buffer's data are
- * assumed to be already transferred into cmd->SCp.this_residual.
- * Every buffer merged avoids an interrupt and a DMA setup operation.
- */
-
-static void merge_contiguous_buffers(struct scsi_cmnd *cmd)
-{
-#if !defined(CONFIG_SUN3)
- unsigned long endaddr;
-#if (NDEBUG & NDEBUG_MERGING)
- unsigned long oldlen = cmd->SCp.this_residual;
- int cnt = 1;
-#endif
-
- for (endaddr = virt_to_phys(cmd->SCp.ptr + cmd->SCp.this_residual - 1) + 1;
- cmd->SCp.buffers_residual &&
- virt_to_phys(sg_virt(&cmd->SCp.buffer[1])) == endaddr;) {
- dprintk(NDEBUG_MERGING, "VTOP(%p) == %08lx -> merging\n",
- page_address(sg_page(&cmd->SCp.buffer[1])), endaddr);
-#if (NDEBUG & NDEBUG_MERGING)
- ++cnt;
-#endif
- ++cmd->SCp.buffer;
- --cmd->SCp.buffers_residual;
- cmd->SCp.this_residual += cmd->SCp.buffer->length;
- endaddr += cmd->SCp.buffer->length;
- }
-#if (NDEBUG & NDEBUG_MERGING)
- if (oldlen != cmd->SCp.this_residual)
- dprintk(NDEBUG_MERGING, "merged %d buffers from %p, new length %08x\n",
- cnt, cmd->SCp.ptr, cmd->SCp.this_residual);
-#endif
-#endif /* !defined(CONFIG_SUN3) */
-}
-
-/**
- * initialize_SCp - init the scsi pointer field
- * @cmd: command block to set up
- *
- * Set up the internal fields in the SCSI command.
- */
-
-static inline void initialize_SCp(struct scsi_cmnd *cmd)
-{
- /*
- * Initialize the Scsi Pointer field so that all of the commands in the
- * various queues are valid.
- */
-
- if (scsi_bufflen(cmd)) {
- cmd->SCp.buffer = scsi_sglist(cmd);
- cmd->SCp.buffers_residual = scsi_sg_count(cmd) - 1;
- cmd->SCp.ptr = sg_virt(cmd->SCp.buffer);
- cmd->SCp.this_residual = cmd->SCp.buffer->length;
-
- merge_contiguous_buffers(cmd);
- } else {
- cmd->SCp.buffer = NULL;
- cmd->SCp.buffers_residual = 0;
- cmd->SCp.ptr = NULL;
- cmd->SCp.this_residual = 0;
- }
-
- cmd->SCp.Status = 0;
- cmd->SCp.Message = 0;
-}
-
-/**
- * NCR5380_poll_politely2 - wait for two chip register values
- * @instance: controller to poll
- * @reg1: 5380 register to poll
- * @bit1: Bitmask to check
- * @val1: Expected value
- * @reg2: Second 5380 register to poll
- * @bit2: Second bitmask to check
- * @val2: Second expected value
- * @wait: Time-out in jiffies
- *
- * Polls the chip in a reasonably efficient manner waiting for an
- * event to occur. After a short quick poll we begin to yield the CPU
- * (if possible). In irq contexts the time-out is arbitrarily limited.
- * Callers may hold locks as long as they are held in irq mode.
- *
- * Returns 0 if either or both event(s) occurred otherwise -ETIMEDOUT.
- */
-
-static int NCR5380_poll_politely2(struct Scsi_Host *instance,
- int reg1, int bit1, int val1,
- int reg2, int bit2, int val2, int wait)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
- unsigned long deadline = jiffies + wait;
- unsigned long n;
-
- /* Busy-wait for up to 10 ms */
- n = min(10000U, jiffies_to_usecs(wait));
- n *= hostdata->accesses_per_ms;
- n /= 2000;
- do {
- if ((NCR5380_read(reg1) & bit1) == val1)
- return 0;
- if ((NCR5380_read(reg2) & bit2) == val2)
- return 0;
- cpu_relax();
- } while (n--);
-
- if (irqs_disabled() || in_interrupt())
- return -ETIMEDOUT;
-
- /* Repeatedly sleep for 1 ms until deadline */
- while (time_is_after_jiffies(deadline)) {
- schedule_timeout_uninterruptible(1);
- if ((NCR5380_read(reg1) & bit1) == val1)
- return 0;
- if ((NCR5380_read(reg2) & bit2) == val2)
- return 0;
- }
-
- return -ETIMEDOUT;
-}
-
-static inline int NCR5380_poll_politely(struct Scsi_Host *instance,
- int reg, int bit, int val, int wait)
-{
- return NCR5380_poll_politely2(instance, reg, bit, val,
- reg, bit, val, wait);
-}
-
-#if NDEBUG
-static struct {
- unsigned char mask;
- const char *name;
-} signals[] = {
- {SR_DBP, "PARITY"},
- {SR_RST, "RST"},
- {SR_BSY, "BSY"},
- {SR_REQ, "REQ"},
- {SR_MSG, "MSG"},
- {SR_CD, "CD"},
- {SR_IO, "IO"},
- {SR_SEL, "SEL"},
- {0, NULL}
-},
-basrs[] = {
- {BASR_ATN, "ATN"},
- {BASR_ACK, "ACK"},
- {0, NULL}
-},
-icrs[] = {
- {ICR_ASSERT_RST, "ASSERT RST"},
- {ICR_ASSERT_ACK, "ASSERT ACK"},
- {ICR_ASSERT_BSY, "ASSERT BSY"},
- {ICR_ASSERT_SEL, "ASSERT SEL"},
- {ICR_ASSERT_ATN, "ASSERT ATN"},
- {ICR_ASSERT_DATA, "ASSERT DATA"},
- {0, NULL}
-},
-mrs[] = {
- {MR_BLOCK_DMA_MODE, "MODE BLOCK DMA"},
- {MR_TARGET, "MODE TARGET"},
- {MR_ENABLE_PAR_CHECK, "MODE PARITY CHECK"},
- {MR_ENABLE_PAR_INTR, "MODE PARITY INTR"},
- {MR_ENABLE_EOP_INTR, "MODE EOP INTR"},
- {MR_MONITOR_BSY, "MODE MONITOR BSY"},
- {MR_DMA_MODE, "MODE DMA"},
- {MR_ARBITRATE, "MODE ARBITRATION"},
- {0, NULL}
-};
-
-/**
- * NCR5380_print - print scsi bus signals
- * @instance: adapter state to dump
- *
- * Print the SCSI bus signals for debugging purposes
- */
-
-static void NCR5380_print(struct Scsi_Host *instance)
-{
- unsigned char status, data, basr, mr, icr, i;
-
- data = NCR5380_read(CURRENT_SCSI_DATA_REG);
- status = NCR5380_read(STATUS_REG);
- mr = NCR5380_read(MODE_REG);
- icr = NCR5380_read(INITIATOR_COMMAND_REG);
- basr = NCR5380_read(BUS_AND_STATUS_REG);
-
- printk("STATUS_REG: %02x ", status);
- for (i = 0; signals[i].mask; ++i)
- if (status & signals[i].mask)
- printk(",%s", signals[i].name);
- printk("\nBASR: %02x ", basr);
- for (i = 0; basrs[i].mask; ++i)
- if (basr & basrs[i].mask)
- printk(",%s", basrs[i].name);
- printk("\nICR: %02x ", icr);
- for (i = 0; icrs[i].mask; ++i)
- if (icr & icrs[i].mask)
- printk(",%s", icrs[i].name);
- printk("\nMODE: %02x ", mr);
- for (i = 0; mrs[i].mask; ++i)
- if (mr & mrs[i].mask)
- printk(",%s", mrs[i].name);
- printk("\n");
-}
-
-static struct {
- unsigned char value;
- const char *name;
-} phases[] = {
- {PHASE_DATAOUT, "DATAOUT"},
- {PHASE_DATAIN, "DATAIN"},
- {PHASE_CMDOUT, "CMDOUT"},
- {PHASE_STATIN, "STATIN"},
- {PHASE_MSGOUT, "MSGOUT"},
- {PHASE_MSGIN, "MSGIN"},
- {PHASE_UNKNOWN, "UNKNOWN"}
-};
-
-/**
- * NCR5380_print_phase - show SCSI phase
- * @instance: adapter to dump
- *
- * Print the current SCSI phase for debugging purposes
- */
-
-static void NCR5380_print_phase(struct Scsi_Host *instance)
-{
- unsigned char status;
- int i;
-
- status = NCR5380_read(STATUS_REG);
- if (!(status & SR_REQ))
- shost_printk(KERN_DEBUG, instance, "REQ not asserted, phase unknown.\n");
- else {
- for (i = 0; (phases[i].value != PHASE_UNKNOWN) &&
- (phases[i].value != (status & PHASE_MASK)); ++i)
- ;
- shost_printk(KERN_DEBUG, instance, "phase %s\n", phases[i].name);
- }
-}
-#endif
-
-/**
- * NCR58380_info - report driver and host information
- * @instance: relevant scsi host instance
- *
- * For use as the host template info() handler.
- */
-
-static const char *NCR5380_info(struct Scsi_Host *instance)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
- return hostdata->info;
-}
-
-static void prepare_info(struct Scsi_Host *instance)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
- snprintf(hostdata->info, sizeof(hostdata->info),
- "%s, io_port 0x%lx, n_io_port %d, "
- "base 0x%lx, irq %d, "
- "can_queue %d, cmd_per_lun %d, "
- "sg_tablesize %d, this_id %d, "
- "flags { %s%s}, "
- "options { %s} ",
- instance->hostt->name, instance->io_port, instance->n_io_port,
- instance->base, instance->irq,
- instance->can_queue, instance->cmd_per_lun,
- instance->sg_tablesize, instance->this_id,
- hostdata->flags & FLAG_TAGGED_QUEUING ? "TAGGED_QUEUING " : "",
- hostdata->flags & FLAG_TOSHIBA_DELAY ? "TOSHIBA_DELAY " : "",
-#ifdef DIFFERENTIAL
- "DIFFERENTIAL "
-#endif
-#ifdef PARITY
- "PARITY "
-#endif
-#ifdef SUPPORT_TAGS
- "SUPPORT_TAGS "
-#endif
- "");
-}
-
-/**
- * NCR5380_init - initialise an NCR5380
- * @instance: adapter to configure
- * @flags: control flags
- *
- * Initializes *instance and corresponding 5380 chip,
- * with flags OR'd into the initial flags value.
- *
- * Notes : I assume that the host, hostno, and id bits have been
- * set correctly. I don't care about the irq and other fields.
- *
- * Returns 0 for success
- */
-
-static int __init NCR5380_init(struct Scsi_Host *instance, int flags)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
- int i;
- unsigned long deadline;
-
- hostdata->host = instance;
- hostdata->id_mask = 1 << instance->this_id;
- hostdata->id_higher_mask = 0;
- for (i = hostdata->id_mask; i <= 0x80; i <<= 1)
- if (i > hostdata->id_mask)
- hostdata->id_higher_mask |= i;
- for (i = 0; i < 8; ++i)
- hostdata->busy[i] = 0;
-#ifdef SUPPORT_TAGS
- init_tags(hostdata);
-#endif
- hostdata->dma_len = 0;
-
- spin_lock_init(&hostdata->lock);
- hostdata->connected = NULL;
- hostdata->sensing = NULL;
- INIT_LIST_HEAD(&hostdata->autosense);
- INIT_LIST_HEAD(&hostdata->unissued);
- INIT_LIST_HEAD(&hostdata->disconnected);
-
- hostdata->flags = flags;
-
- INIT_WORK(&hostdata->main_task, NCR5380_main);
- hostdata->work_q = alloc_workqueue("ncr5380_%d",
- WQ_UNBOUND | WQ_MEM_RECLAIM,
- 1, instance->host_no);
- if (!hostdata->work_q)
- return -ENOMEM;
-
- prepare_info(instance);
-
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- NCR5380_write(MODE_REG, MR_BASE);
- NCR5380_write(TARGET_COMMAND_REG, 0);
- NCR5380_write(SELECT_ENABLE_REG, 0);
-
- /* Calibrate register polling loop */
- i = 0;
- deadline = jiffies + 1;
- do {
- cpu_relax();
- } while (time_is_after_jiffies(deadline));
- deadline += msecs_to_jiffies(256);
- do {
- NCR5380_read(STATUS_REG);
- ++i;
- cpu_relax();
- } while (time_is_after_jiffies(deadline));
- hostdata->accesses_per_ms = i / 256;
-
- return 0;
-}
-
-/**
- * NCR5380_maybe_reset_bus - Detect and correct bus wedge problems.
- * @instance: adapter to check
- *
- * If the system crashed, it may have crashed with a connected target and
- * the SCSI bus busy. Check for BUS FREE phase. If not, try to abort the
- * currently established nexus, which we know nothing about. Failing that
- * do a bus reset.
- *
- * Note that a bus reset will cause the chip to assert IRQ.
- *
- * Returns 0 if successful, otherwise -ENXIO.
- */
-
-static int NCR5380_maybe_reset_bus(struct Scsi_Host *instance)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
- int pass;
-
- for (pass = 1; (NCR5380_read(STATUS_REG) & SR_BSY) && pass <= 6; ++pass) {
- switch (pass) {
- case 1:
- case 3:
- case 5:
- shost_printk(KERN_ERR, instance, "SCSI bus busy, waiting up to five seconds\n");
- NCR5380_poll_politely(instance,
- STATUS_REG, SR_BSY, 0, 5 * HZ);
- break;
- case 2:
- shost_printk(KERN_ERR, instance, "bus busy, attempting abort\n");
- do_abort(instance);
- break;
- case 4:
- shost_printk(KERN_ERR, instance, "bus busy, attempting reset\n");
- do_reset(instance);
- /* Wait after a reset; the SCSI standard calls for
- * 250ms, we wait 500ms to be on the safe side.
- * But some Toshiba CD-ROMs need ten times that.
- */
- if (hostdata->flags & FLAG_TOSHIBA_DELAY)
- msleep(2500);
- else
- msleep(500);
- break;
- case 6:
- shost_printk(KERN_ERR, instance, "bus locked solid\n");
- return -ENXIO;
- }
- }
- return 0;
-}
-
-/**
- * NCR5380_exit - remove an NCR5380
- * @instance: adapter to remove
- *
- * Assumes that no more work can be queued (e.g. by NCR5380_intr).
- */
-
-static void NCR5380_exit(struct Scsi_Host *instance)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
- cancel_work_sync(&hostdata->main_task);
- destroy_workqueue(hostdata->work_q);
-}
-
-/**
- * complete_cmd - finish processing a command and return it to the SCSI ML
- * @instance: the host instance
- * @cmd: command to complete
- */
-
-static void complete_cmd(struct Scsi_Host *instance,
- struct scsi_cmnd *cmd)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
- dsprintk(NDEBUG_QUEUES, instance, "complete_cmd: cmd %p\n", cmd);
-
- if (hostdata->sensing == cmd) {
- /* Autosense processing ends here */
- if ((cmd->result & 0xff) != SAM_STAT_GOOD) {
- scsi_eh_restore_cmnd(cmd, &hostdata->ses);
- set_host_byte(cmd, DID_ERROR);
- } else
- scsi_eh_restore_cmnd(cmd, &hostdata->ses);
- hostdata->sensing = NULL;
- }
-
-#ifdef SUPPORT_TAGS
- cmd_free_tag(cmd);
-#else
- hostdata->busy[scmd_id(cmd)] &= ~(1 << cmd->device->lun);
-#endif
- cmd->scsi_done(cmd);
-}
-
-/**
- * NCR5380_queue_command - queue a command
- * @instance: the relevant SCSI adapter
- * @cmd: SCSI command
- *
- * cmd is added to the per-instance issue queue, with minor
- * twiddling done to the host specific fields of cmd. If the
- * main coroutine is not running, it is restarted.
- */
-
-static int NCR5380_queue_command(struct Scsi_Host *instance,
- struct scsi_cmnd *cmd)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
- struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);
- unsigned long flags;
-
-#if (NDEBUG & NDEBUG_NO_WRITE)
- switch (cmd->cmnd[0]) {
- case WRITE_6:
- case WRITE_10:
- shost_printk(KERN_DEBUG, instance, "WRITE attempted with NDEBUG_NO_WRITE set\n");
- cmd->result = (DID_ERROR << 16);
- cmd->scsi_done(cmd);
- return 0;
- }
-#endif /* (NDEBUG & NDEBUG_NO_WRITE) */
-
- cmd->result = 0;
-
- /*
- * ++roman: Just disabling the NCR interrupt isn't sufficient here,
- * because also a timer int can trigger an abort or reset, which would
- * alter queues and touch the lock.
- */
- if (!NCR5380_acquire_dma_irq(instance))
- return SCSI_MLQUEUE_HOST_BUSY;
-
- spin_lock_irqsave(&hostdata->lock, flags);
-
- /*
- * Insert the cmd into the issue queue. Note that REQUEST SENSE
- * commands are added to the head of the queue since any command will
- * clear the contingent allegiance condition that exists and the
- * sense data is only guaranteed to be valid while the condition exists.
- */
-
- if (cmd->cmnd[0] == REQUEST_SENSE)
- list_add(&ncmd->list, &hostdata->unissued);
- else
- list_add_tail(&ncmd->list, &hostdata->unissued);
-
- spin_unlock_irqrestore(&hostdata->lock, flags);
-
- dsprintk(NDEBUG_QUEUES, instance, "command %p added to %s of queue\n",
- cmd, (cmd->cmnd[0] == REQUEST_SENSE) ? "head" : "tail");
-
- /* Kick off command processing */
- queue_work(hostdata->work_q, &hostdata->main_task);
- return 0;
-}
-
-static inline void maybe_release_dma_irq(struct Scsi_Host *instance)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
-
- /* Caller does the locking needed to set & test these data atomically */
- if (list_empty(&hostdata->disconnected) &&
- list_empty(&hostdata->unissued) &&
- list_empty(&hostdata->autosense) &&
- !hostdata->connected &&
- !hostdata->selecting)
- NCR5380_release_dma_irq(instance);
-}
-
-/**
- * dequeue_next_cmd - dequeue a command for processing
- * @instance: the scsi host instance
- *
- * Priority is given to commands on the autosense queue. These commands
- * need autosense because of a CHECK CONDITION result.
- *
- * Returns a command pointer if a command is found for a target that is
- * not already busy. Otherwise returns NULL.
- */
-
-static struct scsi_cmnd *dequeue_next_cmd(struct Scsi_Host *instance)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
- struct NCR5380_cmd *ncmd;
- struct scsi_cmnd *cmd;
-
- if (hostdata->sensing || list_empty(&hostdata->autosense)) {
- list_for_each_entry(ncmd, &hostdata->unissued, list) {
- cmd = NCR5380_to_scmd(ncmd);
- dsprintk(NDEBUG_QUEUES, instance, "dequeue: cmd=%p target=%d busy=0x%02x lun=%llu\n",
- cmd, scmd_id(cmd), hostdata->busy[scmd_id(cmd)], cmd->device->lun);
-
- if (
-#ifdef SUPPORT_TAGS
- !is_lun_busy(cmd, 1)
-#else
- !(hostdata->busy[scmd_id(cmd)] & (1 << cmd->device->lun))
-#endif
- ) {
- list_del(&ncmd->list);
- dsprintk(NDEBUG_QUEUES, instance,
- "dequeue: removed %p from issue queue\n", cmd);
- return cmd;
- }
- }
- } else {
- /* Autosense processing begins here */
- ncmd = list_first_entry(&hostdata->autosense,
- struct NCR5380_cmd, list);
- list_del(&ncmd->list);
- cmd = NCR5380_to_scmd(ncmd);
- dsprintk(NDEBUG_QUEUES, instance,
- "dequeue: removed %p from autosense queue\n", cmd);
- scsi_eh_prep_cmnd(cmd, &hostdata->ses, NULL, 0, ~0);
- hostdata->sensing = cmd;
- return cmd;
- }
- return NULL;
-}
-
-static void requeue_cmd(struct Scsi_Host *instance, struct scsi_cmnd *cmd)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
- struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);
-
- if (hostdata->sensing == cmd) {
- scsi_eh_restore_cmnd(cmd, &hostdata->ses);
- list_add(&ncmd->list, &hostdata->autosense);
- hostdata->sensing = NULL;
- } else
- list_add(&ncmd->list, &hostdata->unissued);
-}
-
-/**
- * NCR5380_main - NCR state machines
- *
- * NCR5380_main is a coroutine that runs as long as more work can
- * be done on the NCR5380 host adapters in a system. Both
- * NCR5380_queue_command() and NCR5380_intr() will try to start it
- * in case it is not running.
- */
-
-static void NCR5380_main(struct work_struct *work)
-{
- struct NCR5380_hostdata *hostdata =
- container_of(work, struct NCR5380_hostdata, main_task);
- struct Scsi_Host *instance = hostdata->host;
- int done;
-
- /*
- * ++roman: Just disabling the NCR interrupt isn't sufficient here,
- * because also a timer int can trigger an abort or reset, which can
- * alter queues and touch the Falcon lock.
- */
-
- do {
- done = 1;
-
- spin_lock_irq(&hostdata->lock);
- while (!hostdata->connected && !hostdata->selecting) {
- struct scsi_cmnd *cmd = dequeue_next_cmd(instance);
-
- if (!cmd)
- break;
-
- dsprintk(NDEBUG_MAIN, instance, "main: dequeued %p\n", cmd);
-
- /*
- * Attempt to establish an I_T_L nexus here.
- * On success, instance->hostdata->connected is set.
- * On failure, we must add the command back to the
- * issue queue so we can keep trying.
- */
- /*
- * REQUEST SENSE commands are issued without tagged
- * queueing, even on SCSI-II devices because the
- * contingent allegiance condition exists for the
- * entire unit.
- */
- /* ++roman: ...and the standard also requires that
- * REQUEST SENSE command are untagged.
- */
-
-#ifdef SUPPORT_TAGS
- cmd_get_tag(cmd, cmd->cmnd[0] != REQUEST_SENSE);
-#endif
- if (!NCR5380_select(instance, cmd)) {
- dsprintk(NDEBUG_MAIN, instance, "main: select complete\n");
- maybe_release_dma_irq(instance);
- } else {
- dsprintk(NDEBUG_MAIN | NDEBUG_QUEUES, instance,
- "main: select failed, returning %p to queue\n", cmd);
- requeue_cmd(instance, cmd);
-#ifdef SUPPORT_TAGS
- cmd_free_tag(cmd);
-#endif
- }
- }
- if (hostdata->connected && !hostdata->dma_len) {
- dsprintk(NDEBUG_MAIN, instance, "main: performing information transfer\n");
- NCR5380_information_transfer(instance);
- done = 0;
- }
- spin_unlock_irq(&hostdata->lock);
- if (!done)
- cond_resched();
- } while (!done);
-}
-
-
-/*
- * Function : void NCR5380_dma_complete (struct Scsi_Host *instance)
- *
- * Purpose : Called by interrupt handler when DMA finishes or a phase
- * mismatch occurs (which would finish the DMA transfer).
- *
- * Inputs : instance - this instance of the NCR5380.
- */
-
-static void NCR5380_dma_complete(struct Scsi_Host *instance)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
- int transferred;
- unsigned char **data;
- int *count;
- int saved_data = 0, overrun = 0;
- unsigned char p;
-
- if (hostdata->read_overruns) {
- p = hostdata->connected->SCp.phase;
- if (p & SR_IO) {
- udelay(10);
- if ((NCR5380_read(BUS_AND_STATUS_REG) &
- (BASR_PHASE_MATCH|BASR_ACK)) ==
- (BASR_PHASE_MATCH|BASR_ACK)) {
- saved_data = NCR5380_read(INPUT_DATA_REG);
- overrun = 1;
- dsprintk(NDEBUG_DMA, instance, "read overrun handled\n");
- }
- }
- }
-
-#if defined(CONFIG_SUN3)
- if ((sun3scsi_dma_finish(rq_data_dir(hostdata->connected->request)))) {
- pr_err("scsi%d: overrun in UDC counter -- not prepared to deal with this!\n",
- instance->host_no);
- BUG();
- }
-
- /* make sure we're not stuck in a data phase */
- if ((NCR5380_read(BUS_AND_STATUS_REG) & (BASR_PHASE_MATCH | BASR_ACK)) ==
- (BASR_PHASE_MATCH | BASR_ACK)) {
- pr_err("scsi%d: BASR %02x\n", instance->host_no,
- NCR5380_read(BUS_AND_STATUS_REG));
- pr_err("scsi%d: bus stuck in data phase -- probably a single byte overrun!\n",
- instance->host_no);
- BUG();
- }
-#endif
-
- NCR5380_write(MODE_REG, MR_BASE);
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- NCR5380_read(RESET_PARITY_INTERRUPT_REG);
-
- transferred = hostdata->dma_len - NCR5380_dma_residual(instance);
- hostdata->dma_len = 0;
-
- data = (unsigned char **)&hostdata->connected->SCp.ptr;
- count = &hostdata->connected->SCp.this_residual;
- *data += transferred;
- *count -= transferred;
-
- if (hostdata->read_overruns) {
- int cnt, toPIO;
-
- if ((NCR5380_read(STATUS_REG) & PHASE_MASK) == p && (p & SR_IO)) {
- cnt = toPIO = hostdata->read_overruns;
- if (overrun) {
- dprintk(NDEBUG_DMA, "Got an input overrun, using saved byte\n");
- *(*data)++ = saved_data;
- (*count)--;
- cnt--;
- toPIO--;
- }
- dprintk(NDEBUG_DMA, "Doing %d-byte PIO to 0x%08lx\n", cnt, (long)*data);
- NCR5380_transfer_pio(instance, &p, &cnt, data);
- *count -= toPIO - cnt;
- }
- }
-}
-
-
-/**
- * NCR5380_intr - generic NCR5380 irq handler
- * @irq: interrupt number
- * @dev_id: device info
- *
- * Handle interrupts, reestablishing I_T_L or I_T_L_Q nexuses
- * from the disconnected queue, and restarting NCR5380_main()
- * as required.
- *
- * The chip can assert IRQ in any of six different conditions. The IRQ flag
- * is then cleared by reading the Reset Parity/Interrupt Register (RPIR).
- * Three of these six conditions are latched in the Bus and Status Register:
- * - End of DMA (cleared by ending DMA Mode)
- * - Parity error (cleared by reading RPIR)
- * - Loss of BSY (cleared by reading RPIR)
- * Two conditions have flag bits that are not latched:
- * - Bus phase mismatch (non-maskable in DMA Mode, cleared by ending DMA Mode)
- * - Bus reset (non-maskable)
- * The remaining condition has no flag bit at all:
- * - Selection/reselection
- *
- * Hence, establishing the cause(s) of any interrupt is partly guesswork.
- * In "The DP8490 and DP5380 Comparison Guide", National Semiconductor
- * claimed that "the design of the [DP8490] interrupt logic ensures
- * interrupts will not be lost (they can be on the DP5380)."
- * The L5380/53C80 datasheet from LOGIC Devices has more details.
- *
- * Checking for bus reset by reading RST is futile because of interrupt
- * latency, but a bus reset will reset chip logic. Checking for parity error
- * is unnecessary because that interrupt is never enabled. A Loss of BSY
- * condition will clear DMA Mode. We can tell when this occurs because the
- * the Busy Monitor interrupt is enabled together with DMA Mode.
- */
-
-static irqreturn_t NCR5380_intr(int irq, void *dev_id)
-{
- struct Scsi_Host *instance = dev_id;
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
- int handled = 0;
- unsigned char basr;
- unsigned long flags;
-
- spin_lock_irqsave(&hostdata->lock, flags);
-
- basr = NCR5380_read(BUS_AND_STATUS_REG);
- if (basr & BASR_IRQ) {
- unsigned char mr = NCR5380_read(MODE_REG);
- unsigned char sr = NCR5380_read(STATUS_REG);
-
- dsprintk(NDEBUG_INTR, instance, "IRQ %d, BASR 0x%02x, SR 0x%02x, MR 0x%02x\n",
- irq, basr, sr, mr);
-
- if ((mr & MR_DMA_MODE) || (mr & MR_MONITOR_BSY)) {
- /* Probably End of DMA, Phase Mismatch or Loss of BSY.
- * We ack IRQ after clearing Mode Register. Workarounds
- * for End of DMA errata need to happen in DMA Mode.
- */
-
- dsprintk(NDEBUG_INTR, instance, "interrupt in DMA mode\n");
-
- if (hostdata->connected) {
- NCR5380_dma_complete(instance);
- queue_work(hostdata->work_q, &hostdata->main_task);
- } else {
- NCR5380_write(MODE_REG, MR_BASE);
- NCR5380_read(RESET_PARITY_INTERRUPT_REG);
- }
- } else if ((NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_mask) &&
- (sr & (SR_SEL | SR_IO | SR_BSY | SR_RST)) == (SR_SEL | SR_IO)) {
- /* Probably reselected */
- NCR5380_write(SELECT_ENABLE_REG, 0);
- NCR5380_read(RESET_PARITY_INTERRUPT_REG);
-
- dsprintk(NDEBUG_INTR, instance, "interrupt with SEL and IO\n");
-
- if (!hostdata->connected) {
- NCR5380_reselect(instance);
- queue_work(hostdata->work_q, &hostdata->main_task);
- }
- if (!hostdata->connected)
- NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
- } else {
- /* Probably Bus Reset */
- NCR5380_read(RESET_PARITY_INTERRUPT_REG);
-
- dsprintk(NDEBUG_INTR, instance, "unknown interrupt\n");
-#ifdef SUN3_SCSI_VME
- dregs->csr |= CSR_DMA_ENABLE;
-#endif
- }
- handled = 1;
- } else {
- shost_printk(KERN_NOTICE, instance, "interrupt without IRQ bit\n");
-#ifdef SUN3_SCSI_VME
- dregs->csr |= CSR_DMA_ENABLE;
-#endif
- }
-
- spin_unlock_irqrestore(&hostdata->lock, flags);
-
- return IRQ_RETVAL(handled);
-}
-
-/*
- * Function : int NCR5380_select(struct Scsi_Host *instance,
- * struct scsi_cmnd *cmd)
- *
- * Purpose : establishes I_T_L or I_T_L_Q nexus for new or existing command,
- * including ARBITRATION, SELECTION, and initial message out for
- * IDENTIFY and queue messages.
- *
- * Inputs : instance - instantiation of the 5380 driver on which this
- * target lives, cmd - SCSI command to execute.
- *
- * Returns cmd if selection failed but should be retried,
- * NULL if selection failed and should not be retried, or
- * NULL if selection succeeded (hostdata->connected == cmd).
- *
- * Side effects :
- * If bus busy, arbitration failed, etc, NCR5380_select() will exit
- * with registers as they should have been on entry - ie
- * SELECT_ENABLE will be set appropriately, the NCR5380
- * will cease to drive any SCSI bus signals.
- *
- * If successful : I_T_L or I_T_L_Q nexus will be established,
- * instance->connected will be set to cmd.
- * SELECT interrupt will be disabled.
- *
- * If failed (no target) : cmd->scsi_done() will be called, and the
- * cmd->result host byte set to DID_BAD_TARGET.
- */
-
-static struct scsi_cmnd *NCR5380_select(struct Scsi_Host *instance,
- struct scsi_cmnd *cmd)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
- unsigned char tmp[3], phase;
- unsigned char *data;
- int len;
- int err;
-
- NCR5380_dprint(NDEBUG_ARBITRATION, instance);
- dsprintk(NDEBUG_ARBITRATION, instance, "starting arbitration, id = %d\n",
- instance->this_id);
-
- /*
- * Arbitration and selection phases are slow and involve dropping the
- * lock, so we have to watch out for EH. An exception handler may
- * change 'selecting' to NULL. This function will then return NULL
- * so that the caller will forget about 'cmd'. (During information
- * transfer phases, EH may change 'connected' to NULL.)
- */
- hostdata->selecting = cmd;
-
- /*
- * Set the phase bits to 0, otherwise the NCR5380 won't drive the
- * data bus during SELECTION.
- */
-
- NCR5380_write(TARGET_COMMAND_REG, 0);
-
- /*
- * Start arbitration.
- */
-
- NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask);
- NCR5380_write(MODE_REG, MR_ARBITRATE);
-
- /* The chip now waits for BUS FREE phase. Then after the 800 ns
- * Bus Free Delay, arbitration will begin.
- */
-
- spin_unlock_irq(&hostdata->lock);
- err = NCR5380_poll_politely2(instance, MODE_REG, MR_ARBITRATE, 0,
- INITIATOR_COMMAND_REG, ICR_ARBITRATION_PROGRESS,
- ICR_ARBITRATION_PROGRESS, HZ);
- spin_lock_irq(&hostdata->lock);
- if (!(NCR5380_read(MODE_REG) & MR_ARBITRATE)) {
- /* Reselection interrupt */
- goto out;
- }
- if (!hostdata->selecting) {
- /* Command was aborted */
- NCR5380_write(MODE_REG, MR_BASE);
- goto out;
- }
- if (err < 0) {
- NCR5380_write(MODE_REG, MR_BASE);
- shost_printk(KERN_ERR, instance,
- "select: arbitration timeout\n");
- goto out;
- }
- spin_unlock_irq(&hostdata->lock);
-
- /* The SCSI-2 arbitration delay is 2.4 us */
- udelay(3);
-
- /* Check for lost arbitration */
- if ((NCR5380_read(INITIATOR_COMMAND_REG) & ICR_ARBITRATION_LOST) ||
- (NCR5380_read(CURRENT_SCSI_DATA_REG) & hostdata->id_higher_mask) ||
- (NCR5380_read(INITIATOR_COMMAND_REG) & ICR_ARBITRATION_LOST)) {
- NCR5380_write(MODE_REG, MR_BASE);
- dsprintk(NDEBUG_ARBITRATION, instance, "lost arbitration, deasserting MR_ARBITRATE\n");
- spin_lock_irq(&hostdata->lock);
- goto out;
- }
-
- /* After/during arbitration, BSY should be asserted.
- * IBM DPES-31080 Version S31Q works now
- * Tnx to Thomas_Roesch@xxxxxxxxxx for finding this! (Roman)
- */
- NCR5380_write(INITIATOR_COMMAND_REG,
- ICR_BASE | ICR_ASSERT_SEL | ICR_ASSERT_BSY);
-
- /*
- * Again, bus clear + bus settle time is 1.2us, however, this is
- * a minimum so we'll udelay ceil(1.2)
- */
-
- if (hostdata->flags & FLAG_TOSHIBA_DELAY)
- udelay(15);
- else
- udelay(2);
-
- spin_lock_irq(&hostdata->lock);
-
- /* NCR5380_reselect() clears MODE_REG after a reselection interrupt */
- if (!(NCR5380_read(MODE_REG) & MR_ARBITRATE))
- goto out;
-
- if (!hostdata->selecting) {
- NCR5380_write(MODE_REG, MR_BASE);
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- goto out;
- }
-
- dsprintk(NDEBUG_ARBITRATION, instance, "won arbitration\n");
-
- /*
- * Now that we have won arbitration, start Selection process, asserting
- * the host and target ID's on the SCSI bus.
- */
-
- NCR5380_write(OUTPUT_DATA_REG, hostdata->id_mask | (1 << scmd_id(cmd)));
-
- /*
- * Raise ATN while SEL is true before BSY goes false from arbitration,
- * since this is the only way to guarantee that we'll get a MESSAGE OUT
- * phase immediately after selection.
- */
-
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_BSY |
- ICR_ASSERT_DATA | ICR_ASSERT_ATN | ICR_ASSERT_SEL);
- NCR5380_write(MODE_REG, MR_BASE);
-
- /*
- * Reselect interrupts must be turned off prior to the dropping of BSY,
- * otherwise we will trigger an interrupt.
- */
- NCR5380_write(SELECT_ENABLE_REG, 0);
-
- spin_unlock_irq(&hostdata->lock);
-
- /*
- * The initiator shall then wait at least two deskew delays and release
- * the BSY signal.
- */
- udelay(1); /* wingel -- wait two bus deskew delay >2*45ns */
-
- /* Reset BSY */
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA |
- ICR_ASSERT_ATN | ICR_ASSERT_SEL);
-
- /*
- * Something weird happens when we cease to drive BSY - looks
- * like the board/chip is letting us do another read before the
- * appropriate propagation delay has expired, and we're confusing
- * a BSY signal from ourselves as the target's response to SELECTION.
- *
- * A small delay (the 'C++' frontend breaks the pipeline with an
- * unnecessary jump, making it work on my 386-33/Trantor T128, the
- * tighter 'C' code breaks and requires this) solves the problem -
- * the 1 us delay is arbitrary, and only used because this delay will
- * be the same on other platforms and since it works here, it should
- * work there.
- *
- * wingel suggests that this could be due to failing to wait
- * one deskew delay.
- */
-
- udelay(1);
-
- dsprintk(NDEBUG_SELECTION, instance, "selecting target %d\n", scmd_id(cmd));
-
- /*
- * The SCSI specification calls for a 250 ms timeout for the actual
- * selection.
- */
-
- err = NCR5380_poll_politely(instance, STATUS_REG, SR_BSY, SR_BSY,
- msecs_to_jiffies(250));
-
- if ((NCR5380_read(STATUS_REG) & (SR_SEL | SR_IO)) == (SR_SEL | SR_IO)) {
- spin_lock_irq(&hostdata->lock);
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- NCR5380_reselect(instance);
- if (!hostdata->connected)
- NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
- shost_printk(KERN_ERR, instance, "reselection after won arbitration?\n");
- goto out;
- }
-
- if (err < 0) {
- spin_lock_irq(&hostdata->lock);
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
- /* Can't touch cmd if it has been reclaimed by the scsi ML */
- if (hostdata->selecting) {
- cmd->result = DID_BAD_TARGET << 16;
- complete_cmd(instance, cmd);
- dsprintk(NDEBUG_SELECTION, instance, "target did not respond within 250ms\n");
- cmd = NULL;
- }
- goto out;
- }
-
- /*
- * No less than two deskew delays after the initiator detects the
- * BSY signal is true, it shall release the SEL signal and may
- * change the DATA BUS. -wingel
- */
-
- udelay(1);
-
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
-
- /*
- * Since we followed the SCSI spec, and raised ATN while SEL
- * was true but before BSY was false during selection, the information
- * transfer phase should be a MESSAGE OUT phase so that we can send the
- * IDENTIFY message.
- *
- * If SCSI-II tagged queuing is enabled, we also send a SIMPLE_QUEUE_TAG
- * message (2 bytes) with a tag ID that we increment with every command
- * until it wraps back to 0.
- *
- * XXX - it turns out that there are some broken SCSI-II devices,
- * which claim to support tagged queuing but fail when more than
- * some number of commands are issued at once.
- */
-
- /* Wait for start of REQ/ACK handshake */
-
- err = NCR5380_poll_politely(instance, STATUS_REG, SR_REQ, SR_REQ, HZ);
- spin_lock_irq(&hostdata->lock);
- if (err < 0) {
- shost_printk(KERN_ERR, instance, "select: REQ timeout\n");
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
- goto out;
- }
- if (!hostdata->selecting) {
- do_abort(instance);
- goto out;
- }
-
- dsprintk(NDEBUG_SELECTION, instance, "target %d selected, going into MESSAGE OUT phase.\n",
- scmd_id(cmd));
- tmp[0] = IDENTIFY(1, cmd->device->lun);
-
-#ifdef SUPPORT_TAGS
- if (cmd->tag != TAG_NONE) {
- tmp[1] = hostdata->last_message = SIMPLE_QUEUE_TAG;
- tmp[2] = cmd->tag;
- len = 3;
- } else
- len = 1;
-#else
- len = 1;
- cmd->tag = 0;
-#endif /* SUPPORT_TAGS */
-
- /* Send message(s) */
- data = tmp;
- phase = PHASE_MSGOUT;
- NCR5380_transfer_pio(instance, &phase, &len, &data);
- dsprintk(NDEBUG_SELECTION, instance, "nexus established.\n");
- /* XXX need to handle errors here */
-
- hostdata->connected = cmd;
-#ifndef SUPPORT_TAGS
- hostdata->busy[cmd->device->id] |= 1 << cmd->device->lun;
-#endif
-#ifdef SUN3_SCSI_VME
- dregs->csr |= CSR_INTR;
-#endif
-
- initialize_SCp(cmd);
-
- cmd = NULL;
-
-out:
- if (!hostdata->selecting)
- return NULL;
- hostdata->selecting = NULL;
- return cmd;
-}
-
-/*
- * Function : int NCR5380_transfer_pio (struct Scsi_Host *instance,
- * unsigned char *phase, int *count, unsigned char **data)
- *
- * Purpose : transfers data in given phase using polled I/O
- *
- * Inputs : instance - instance of driver, *phase - pointer to
- * what phase is expected, *count - pointer to number of
- * bytes to transfer, **data - pointer to data pointer.
- *
- * Returns : -1 when different phase is entered without transferring
- * maximum number of bytes, 0 if all bytes are transferred or exit
- * is in same phase.
- *
- * Also, *phase, *count, *data are modified in place.
- *
- * XXX Note : handling for bus free may be useful.
- */
-
-/*
- * Note : this code is not as quick as it could be, however it
- * IS 100% reliable, and for the actual data transfer where speed
- * counts, we will always do a pseudo DMA or DMA transfer.
- */
-
-static int NCR5380_transfer_pio(struct Scsi_Host *instance,
- unsigned char *phase, int *count,
- unsigned char **data)
-{
- unsigned char p = *phase, tmp;
- int c = *count;
- unsigned char *d = *data;
-
- /*
- * The NCR5380 chip will only drive the SCSI bus when the
- * phase specified in the appropriate bits of the TARGET COMMAND
- * REGISTER match the STATUS REGISTER
- */
-
- NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
-
- do {
- /*
- * Wait for assertion of REQ, after which the phase bits will be
- * valid
- */
-
- if (NCR5380_poll_politely(instance, STATUS_REG, SR_REQ, SR_REQ, HZ) < 0)
- break;
-
- dsprintk(NDEBUG_HANDSHAKE, instance, "REQ asserted\n");
-
- /* Check for phase mismatch */
- if ((NCR5380_read(STATUS_REG) & PHASE_MASK) != p) {
- dsprintk(NDEBUG_PIO, instance, "phase mismatch\n");
- NCR5380_dprint_phase(NDEBUG_PIO, instance);
- break;
- }
-
- /* Do actual transfer from SCSI bus to / from memory */
- if (!(p & SR_IO))
- NCR5380_write(OUTPUT_DATA_REG, *d);
- else
- *d = NCR5380_read(CURRENT_SCSI_DATA_REG);
-
- ++d;
-
- /*
- * The SCSI standard suggests that in MSGOUT phase, the initiator
- * should drop ATN on the last byte of the message phase
- * after REQ has been asserted for the handshake but before
- * the initiator raises ACK.
- */
-
- if (!(p & SR_IO)) {
- if (!((p & SR_MSG) && c > 1)) {
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA);
- NCR5380_dprint(NDEBUG_PIO, instance);
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
- ICR_ASSERT_DATA | ICR_ASSERT_ACK);
- } else {
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
- ICR_ASSERT_DATA | ICR_ASSERT_ATN);
- NCR5380_dprint(NDEBUG_PIO, instance);
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
- ICR_ASSERT_DATA | ICR_ASSERT_ATN | ICR_ASSERT_ACK);
- }
- } else {
- NCR5380_dprint(NDEBUG_PIO, instance);
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ACK);
- }
-
- if (NCR5380_poll_politely(instance,
- STATUS_REG, SR_REQ, 0, 5 * HZ) < 0)
- break;
-
- dsprintk(NDEBUG_HANDSHAKE, instance, "REQ negated, handshake complete\n");
-
-/*
- * We have several special cases to consider during REQ/ACK handshaking :
- * 1. We were in MSGOUT phase, and we are on the last byte of the
- * message. ATN must be dropped as ACK is dropped.
- *
- * 2. We are in a MSGIN phase, and we are on the last byte of the
- * message. We must exit with ACK asserted, so that the calling
- * code may raise ATN before dropping ACK to reject the message.
- *
- * 3. ACK and ATN are clear and the target may proceed as normal.
- */
- if (!(p == PHASE_MSGIN && c == 1)) {
- if (p == PHASE_MSGOUT && c > 1)
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
- else
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- }
- } while (--c);
-
- dsprintk(NDEBUG_PIO, instance, "residual %d\n", c);
-
- *count = c;
- *data = d;
- tmp = NCR5380_read(STATUS_REG);
- /* The phase read from the bus is valid if either REQ is (already)
- * asserted or if ACK hasn't been released yet. The latter applies if
- * we're in MSG IN, DATA IN or STATUS and all bytes have been received.
- */
- if ((tmp & SR_REQ) || ((tmp & SR_IO) && c == 0))
- *phase = tmp & PHASE_MASK;
- else
- *phase = PHASE_UNKNOWN;
-
- if (!c || (*phase == p))
- return 0;
- else
- return -1;
-}
-
-/**
- * do_reset - issue a reset command
- * @instance: adapter to reset
- *
- * Issue a reset sequence to the NCR5380 and try and get the bus
- * back into sane shape.
- *
- * This clears the reset interrupt flag because there may be no handler for
- * it. When the driver is initialized, the NCR5380_intr() handler has not yet
- * been installed. And when in EH we may have released the ST DMA interrupt.
- */
-
-static void do_reset(struct Scsi_Host *instance)
-{
- unsigned long flags;
-
- local_irq_save(flags);
- NCR5380_write(TARGET_COMMAND_REG,
- PHASE_SR_TO_TCR(NCR5380_read(STATUS_REG) & PHASE_MASK));
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_RST);
- udelay(50);
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- (void)NCR5380_read(RESET_PARITY_INTERRUPT_REG);
- local_irq_restore(flags);
-}
-
-/**
- * do_abort - abort the currently established nexus by going to
- * MESSAGE OUT phase and sending an ABORT message.
- * @instance: relevant scsi host instance
- *
- * Returns 0 on success, -1 on failure.
- */
-
-static int do_abort(struct Scsi_Host *instance)
-{
- unsigned char *msgptr, phase, tmp;
- int len;
- int rc;
-
- /* Request message out phase */
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
-
- /*
- * Wait for the target to indicate a valid phase by asserting
- * REQ. Once this happens, we'll have either a MSGOUT phase
- * and can immediately send the ABORT message, or we'll have some
- * other phase and will have to source/sink data.
- *
- * We really don't care what value was on the bus or what value
- * the target sees, so we just handshake.
- */
-
- rc = NCR5380_poll_politely(instance, STATUS_REG, SR_REQ, SR_REQ, 10 * HZ);
- if (rc < 0)
- goto timeout;
-
- tmp = NCR5380_read(STATUS_REG) & PHASE_MASK;
-
- NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(tmp));
-
- if (tmp != PHASE_MSGOUT) {
- NCR5380_write(INITIATOR_COMMAND_REG,
- ICR_BASE | ICR_ASSERT_ATN | ICR_ASSERT_ACK);
- rc = NCR5380_poll_politely(instance, STATUS_REG, SR_REQ, 0, 3 * HZ);
- if (rc < 0)
- goto timeout;
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
- }
-
- tmp = ABORT;
- msgptr = &tmp;
- len = 1;
- phase = PHASE_MSGOUT;
- NCR5380_transfer_pio(instance, &phase, &len, &msgptr);
-
- /*
- * If we got here, and the command completed successfully,
- * we're about to go into bus free state.
- */
-
- return len ? -1 : 0;
-
-timeout:
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- return -1;
-}
-
-
-/*
- * Function : int NCR5380_transfer_dma (struct Scsi_Host *instance,
- * unsigned char *phase, int *count, unsigned char **data)
- *
- * Purpose : transfers data in given phase using either real
- * or pseudo DMA.
- *
- * Inputs : instance - instance of driver, *phase - pointer to
- * what phase is expected, *count - pointer to number of
- * bytes to transfer, **data - pointer to data pointer.
- *
- * Returns : -1 when different phase is entered without transferring
- * maximum number of bytes, 0 if all bytes or transferred or exit
- * is in same phase.
- *
- * Also, *phase, *count, *data are modified in place.
- */
-
-
-static int NCR5380_transfer_dma(struct Scsi_Host *instance,
- unsigned char *phase, int *count,
- unsigned char **data)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
- register int c = *count;
- register unsigned char p = *phase;
-
-#if defined(CONFIG_SUN3)
- /* sanity check */
- if (!sun3_dma_setup_done) {
- pr_err("scsi%d: transfer_dma without setup!\n",
- instance->host_no);
- BUG();
- }
- hostdata->dma_len = c;
-
- dsprintk(NDEBUG_DMA, instance, "initializing DMA %s: length %d, address %p\n",
- (p & SR_IO) ? "receive" : "send", c, *data);
-
- /* netbsd turns off ints here, why not be safe and do it too */
-
- /* send start chain */
- sun3scsi_dma_start(c, *data);
-
- NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
- NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY |
- MR_ENABLE_EOP_INTR);
- if (p & SR_IO) {
- NCR5380_write(INITIATOR_COMMAND_REG, 0);
- NCR5380_write(START_DMA_INITIATOR_RECEIVE_REG, 0);
- } else {
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_ASSERT_DATA);
- NCR5380_write(START_DMA_SEND_REG, 0);
- }
-
-#ifdef SUN3_SCSI_VME
- dregs->csr |= CSR_DMA_ENABLE;
-#endif
-
- sun3_dma_active = 1;
-
-#else /* !defined(CONFIG_SUN3) */
- register unsigned char *d = *data;
- unsigned char tmp;
-
- if ((tmp = (NCR5380_read(STATUS_REG) & PHASE_MASK)) != p) {
- *phase = tmp;
- return -1;
- }
-
- if (hostdata->read_overruns && (p & SR_IO))
- c -= hostdata->read_overruns;
-
- dsprintk(NDEBUG_DMA, instance, "initializing DMA %s: length %d, address %p\n",
- (p & SR_IO) ? "receive" : "send", c, d);
-
- NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(p));
- NCR5380_write(MODE_REG, MR_BASE | MR_DMA_MODE | MR_MONITOR_BSY |
- MR_ENABLE_EOP_INTR);
-
- if (!(hostdata->flags & FLAG_LATE_DMA_SETUP)) {
- /* On the Medusa, it is a must to initialize the DMA before
- * starting the NCR. This is also the cleaner way for the TT.
- */
- hostdata->dma_len = (p & SR_IO) ?
- NCR5380_dma_read_setup(instance, d, c) :
- NCR5380_dma_write_setup(instance, d, c);
- }
-
- if (p & SR_IO)
- NCR5380_write(START_DMA_INITIATOR_RECEIVE_REG, 0);
- else {
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_DATA);
- NCR5380_write(START_DMA_SEND_REG, 0);
- }
-
- if (hostdata->flags & FLAG_LATE_DMA_SETUP) {
- /* On the Falcon, the DMA setup must be done after the last */
- /* NCR access, else the DMA setup gets trashed!
- */
- hostdata->dma_len = (p & SR_IO) ?
- NCR5380_dma_read_setup(instance, d, c) :
- NCR5380_dma_write_setup(instance, d, c);
- }
-#endif /* !defined(CONFIG_SUN3) */
-
- return 0;
-}
-
-/*
- * Function : NCR5380_information_transfer (struct Scsi_Host *instance)
- *
- * Purpose : run through the various SCSI phases and do as the target
- * directs us to. Operates on the currently connected command,
- * instance->connected.
- *
- * Inputs : instance, instance for which we are doing commands
- *
- * Side effects : SCSI things happen, the disconnected queue will be
- * modified if a command disconnects, *instance->connected will
- * change.
- *
- * XXX Note : we need to watch for bus free or a reset condition here
- * to recover from an unexpected bus free condition.
- */
-
-static void NCR5380_information_transfer(struct Scsi_Host *instance)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
- unsigned char msgout = NOP;
- int sink = 0;
- int len;
- int transfersize;
- unsigned char *data;
- unsigned char phase, tmp, extended_msg[10], old_phase = 0xff;
- struct scsi_cmnd *cmd;
-
-#ifdef SUN3_SCSI_VME
- dregs->csr |= CSR_INTR;
-#endif
-
- while ((cmd = hostdata->connected)) {
- struct NCR5380_cmd *ncmd = scsi_cmd_priv(cmd);
-
- tmp = NCR5380_read(STATUS_REG);
- /* We only have a valid SCSI phase when REQ is asserted */
- if (tmp & SR_REQ) {
- phase = (tmp & PHASE_MASK);
- if (phase != old_phase) {
- old_phase = phase;
- NCR5380_dprint_phase(NDEBUG_INFORMATION, instance);
- }
-#if defined(CONFIG_SUN3)
- if (phase == PHASE_CMDOUT) {
- void *d;
- unsigned long count;
-
- if (!cmd->SCp.this_residual && cmd->SCp.buffers_residual) {
- count = cmd->SCp.buffer->length;
- d = sg_virt(cmd->SCp.buffer);
- } else {
- count = cmd->SCp.this_residual;
- d = cmd->SCp.ptr;
- }
- /* this command setup for dma yet? */
- if (sun3_dma_setup_done != cmd &&
- sun3scsi_dma_xfer_len(count, cmd) > 0) {
- sun3scsi_dma_setup(instance, d, count,
- rq_data_dir(cmd->request));
- sun3_dma_setup_done = cmd;
- }
-#ifdef SUN3_SCSI_VME
- dregs->csr |= CSR_INTR;
-#endif
- }
-#endif /* CONFIG_SUN3 */
-
- if (sink && (phase != PHASE_MSGOUT)) {
- NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(tmp));
-
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN |
- ICR_ASSERT_ACK);
- while (NCR5380_read(STATUS_REG) & SR_REQ)
- ;
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE |
- ICR_ASSERT_ATN);
- sink = 0;
- continue;
- }
-
- switch (phase) {
- case PHASE_DATAOUT:
-#if (NDEBUG & NDEBUG_NO_DATAOUT)
- shost_printk(KERN_DEBUG, instance, "NDEBUG_NO_DATAOUT set, attempted DATAOUT aborted\n");
- sink = 1;
- do_abort(instance);
- cmd->result = DID_ERROR << 16;
- complete_cmd(instance, cmd);
- hostdata->connected = NULL;
- return;
-#endif
- case PHASE_DATAIN:
- /*
- * If there is no room left in the current buffer in the
- * scatter-gather list, move onto the next one.
- */
-
- if (!cmd->SCp.this_residual && cmd->SCp.buffers_residual) {
- ++cmd->SCp.buffer;
- --cmd->SCp.buffers_residual;
- cmd->SCp.this_residual = cmd->SCp.buffer->length;
- cmd->SCp.ptr = sg_virt(cmd->SCp.buffer);
- merge_contiguous_buffers(cmd);
- dsprintk(NDEBUG_INFORMATION, instance, "%d bytes and %d buffers left\n",
- cmd->SCp.this_residual,
- cmd->SCp.buffers_residual);
- }
-
- /*
- * The preferred transfer method is going to be
- * PSEUDO-DMA for systems that are strictly PIO,
- * since we can let the hardware do the handshaking.
- *
- * For this to work, we need to know the transfersize
- * ahead of time, since the pseudo-DMA code will sit
- * in an unconditional loop.
- */
-
-#if !defined(CONFIG_SUN3)
- transfersize = 0;
- if (!cmd->device->borken)
-#endif
- transfersize = NCR5380_dma_xfer_len(instance, cmd, phase);
-
- if (transfersize > 0) {
- len = transfersize;
- cmd->SCp.phase = phase;
- if (NCR5380_transfer_dma(instance, &phase,
- &len, (unsigned char **)&cmd->SCp.ptr)) {
- /*
- * If the watchdog timer fires, all future
- * accesses to this device will use the
- * polled-IO.
- */
- scmd_printk(KERN_INFO, cmd,
- "switching to slow handshake\n");
- cmd->device->borken = 1;
- sink = 1;
- do_abort(instance);
- cmd->result = DID_ERROR << 16;
- /* XXX - need to source or sink data here, as appropriate */
- } else
- return;
- } else {
- /* Break up transfer into 3 ms chunks,
- * presuming 6 accesses per handshake.
- */
- transfersize = min((unsigned long)cmd->SCp.this_residual,
- hostdata->accesses_per_ms / 2);
- len = transfersize;
- NCR5380_transfer_pio(instance, &phase, &len,
- (unsigned char **)&cmd->SCp.ptr);
- cmd->SCp.this_residual -= transfersize - len;
- }
-#if defined(CONFIG_SUN3)
- /* if we had intended to dma that command clear it */
- if (sun3_dma_setup_done == cmd)
- sun3_dma_setup_done = NULL;
-#endif
- return;
- case PHASE_MSGIN:
- len = 1;
- data = &tmp;
- NCR5380_transfer_pio(instance, &phase, &len, &data);
- cmd->SCp.Message = tmp;
-
- switch (tmp) {
- case ABORT:
- case COMMAND_COMPLETE:
- /* Accept message by clearing ACK */
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- dsprintk(NDEBUG_QUEUES, instance,
- "COMMAND COMPLETE %p target %d lun %llu\n",
- cmd, scmd_id(cmd), cmd->device->lun);
-
- hostdata->connected = NULL;
-#ifdef SUPPORT_TAGS
- cmd_free_tag(cmd);
- if (status_byte(cmd->SCp.Status) == QUEUE_FULL) {
- u8 lun = cmd->device->lun;
- struct tag_alloc *ta = &hostdata->TagAlloc[scmd_id(cmd)][lun];
-
- dsprintk(NDEBUG_TAGS, instance,
- "QUEUE_FULL %p target %d lun %d nr_allocated %d\n",
- cmd, scmd_id(cmd), lun, ta->nr_allocated);
- if (ta->queue_size > ta->nr_allocated)
- ta->queue_size = ta->nr_allocated;
- }
-#endif
-
- cmd->result &= ~0xffff;
- cmd->result |= cmd->SCp.Status;
- cmd->result |= cmd->SCp.Message << 8;
-
- if (cmd->cmnd[0] == REQUEST_SENSE)
- complete_cmd(instance, cmd);
- else {
- if (cmd->SCp.Status == SAM_STAT_CHECK_CONDITION ||
- cmd->SCp.Status == SAM_STAT_COMMAND_TERMINATED) {
- dsprintk(NDEBUG_QUEUES, instance, "autosense: adding cmd %p to tail of autosense queue\n",
- cmd);
- list_add_tail(&ncmd->list,
- &hostdata->autosense);
- } else
- complete_cmd(instance, cmd);
- }
-
- /*
- * Restore phase bits to 0 so an interrupted selection,
- * arbitration can resume.
- */
- NCR5380_write(TARGET_COMMAND_REG, 0);
-
- /* Enable reselect interrupts */
- NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
-
- maybe_release_dma_irq(instance);
- return;
- case MESSAGE_REJECT:
- /* Accept message by clearing ACK */
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- switch (hostdata->last_message) {
- case HEAD_OF_QUEUE_TAG:
- case ORDERED_QUEUE_TAG:
- case SIMPLE_QUEUE_TAG:
- /* The target obviously doesn't support tagged
- * queuing, even though it announced this ability in
- * its INQUIRY data ?!? (maybe only this LUN?) Ok,
- * clear 'tagged_supported' and lock the LUN, since
- * the command is treated as untagged further on.
- */
- cmd->device->tagged_supported = 0;
- hostdata->busy[cmd->device->id] |= (1 << cmd->device->lun);
- cmd->tag = TAG_NONE;
- dsprintk(NDEBUG_TAGS, instance, "target %d lun %llu rejected QUEUE_TAG message; tagged queuing disabled\n",
- scmd_id(cmd), cmd->device->lun);
- break;
- }
- break;
- case DISCONNECT:
- /* Accept message by clearing ACK */
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- hostdata->connected = NULL;
- list_add(&ncmd->list, &hostdata->disconnected);
- dsprintk(NDEBUG_INFORMATION | NDEBUG_QUEUES,
- instance, "connected command %p for target %d lun %llu moved to disconnected queue\n",
- cmd, scmd_id(cmd), cmd->device->lun);
-
- /*
- * Restore phase bits to 0 so an interrupted selection,
- * arbitration can resume.
- */
- NCR5380_write(TARGET_COMMAND_REG, 0);
-
- /* Enable reselect interrupts */
- NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
-#ifdef SUN3_SCSI_VME
- dregs->csr |= CSR_DMA_ENABLE;
-#endif
- return;
- /*
- * The SCSI data pointer is *IMPLICITLY* saved on a disconnect
- * operation, in violation of the SCSI spec so we can safely
- * ignore SAVE/RESTORE pointers calls.
- *
- * Unfortunately, some disks violate the SCSI spec and
- * don't issue the required SAVE_POINTERS message before
- * disconnecting, and we have to break spec to remain
- * compatible.
- */
- case SAVE_POINTERS:
- case RESTORE_POINTERS:
- /* Accept message by clearing ACK */
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- break;
- case EXTENDED_MESSAGE:
- /*
- * Start the message buffer with the EXTENDED_MESSAGE
- * byte, since spi_print_msg() wants the whole thing.
- */
- extended_msg[0] = EXTENDED_MESSAGE;
- /* Accept first byte by clearing ACK */
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-
- spin_unlock_irq(&hostdata->lock);
-
- dsprintk(NDEBUG_EXTENDED, instance, "receiving extended message\n");
-
- len = 2;
- data = extended_msg + 1;
- phase = PHASE_MSGIN;
- NCR5380_transfer_pio(instance, &phase, &len, &data);
- dsprintk(NDEBUG_EXTENDED, instance, "length %d, code 0x%02x\n",
- (int)extended_msg[1],
- (int)extended_msg[2]);
-
- if (!len && extended_msg[1] > 0 &&
- extended_msg[1] <= sizeof(extended_msg) - 2) {
- /* Accept third byte by clearing ACK */
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- len = extended_msg[1] - 1;
- data = extended_msg + 3;
- phase = PHASE_MSGIN;
-
- NCR5380_transfer_pio(instance, &phase, &len, &data);
- dsprintk(NDEBUG_EXTENDED, instance, "message received, residual %d\n",
- len);
-
- switch (extended_msg[2]) {
- case EXTENDED_SDTR:
- case EXTENDED_WDTR:
- case EXTENDED_MODIFY_DATA_POINTER:
- case EXTENDED_EXTENDED_IDENTIFY:
- tmp = 0;
- }
- } else if (len) {
- shost_printk(KERN_ERR, instance, "error receiving extended message\n");
- tmp = 0;
- } else {
- shost_printk(KERN_NOTICE, instance, "extended message code %02x length %d is too long\n",
- extended_msg[2], extended_msg[1]);
- tmp = 0;
- }
-
- spin_lock_irq(&hostdata->lock);
- if (!hostdata->connected)
- return;
-
- /* Fall through to reject message */
-
- /*
- * If we get something weird that we aren't expecting,
- * reject it.
- */
- default:
- if (!tmp) {
- shost_printk(KERN_ERR, instance, "rejecting message ");
- spi_print_msg(extended_msg);
- printk("\n");
- } else if (tmp != EXTENDED_MESSAGE)
- scmd_printk(KERN_INFO, cmd,
- "rejecting unknown message %02x\n",
- tmp);
- else
- scmd_printk(KERN_INFO, cmd,
- "rejecting unknown extended message code %02x, length %d\n",
- extended_msg[1], extended_msg[0]);
-
- msgout = MESSAGE_REJECT;
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ATN);
- break;
- } /* switch (tmp) */
- break;
- case PHASE_MSGOUT:
- len = 1;
- data = &msgout;
- hostdata->last_message = msgout;
- NCR5380_transfer_pio(instance, &phase, &len, &data);
- if (msgout == ABORT) {
- hostdata->connected = NULL;
- cmd->result = DID_ERROR << 16;
- complete_cmd(instance, cmd);
- maybe_release_dma_irq(instance);
- NCR5380_write(SELECT_ENABLE_REG, hostdata->id_mask);
- return;
- }
- msgout = NOP;
- break;
- case PHASE_CMDOUT:
- len = cmd->cmd_len;
- data = cmd->cmnd;
- /*
- * XXX for performance reasons, on machines with a
- * PSEUDO-DMA architecture we should probably
- * use the dma transfer function.
- */
- NCR5380_transfer_pio(instance, &phase, &len, &data);
- break;
- case PHASE_STATIN:
- len = 1;
- data = &tmp;
- NCR5380_transfer_pio(instance, &phase, &len, &data);
- cmd->SCp.Status = tmp;
- break;
- default:
- shost_printk(KERN_ERR, instance, "unknown phase\n");
- NCR5380_dprint(NDEBUG_ANY, instance);
- } /* switch(phase) */
- } else {
- spin_unlock_irq(&hostdata->lock);
- NCR5380_poll_politely(instance, STATUS_REG, SR_REQ, SR_REQ, HZ);
- spin_lock_irq(&hostdata->lock);
- }
- }
-}
-
-/*
- * Function : void NCR5380_reselect (struct Scsi_Host *instance)
- *
- * Purpose : does reselection, initializing the instance->connected
- * field to point to the scsi_cmnd for which the I_T_L or I_T_L_Q
- * nexus has been reestablished,
- *
- * Inputs : instance - this instance of the NCR5380.
- */
-
-
-/* it might eventually prove necessary to do a dma setup on
- reselection, but it doesn't seem to be needed now -- sam */
-
-static void NCR5380_reselect(struct Scsi_Host *instance)
-{
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
- unsigned char target_mask;
- unsigned char lun;
-#ifdef SUPPORT_TAGS
- unsigned char tag;
-#endif
- unsigned char msg[3];
- int __maybe_unused len;
- unsigned char __maybe_unused *data, __maybe_unused phase;
- struct NCR5380_cmd *ncmd;
- struct scsi_cmnd *tmp;
-
- /*
- * Disable arbitration, etc. since the host adapter obviously
- * lost, and tell an interrupted NCR5380_select() to restart.
- */
-
- NCR5380_write(MODE_REG, MR_BASE);
-
- target_mask = NCR5380_read(CURRENT_SCSI_DATA_REG) & ~(hostdata->id_mask);
-
- dsprintk(NDEBUG_RESELECTION, instance, "reselect\n");
-
- /*
- * At this point, we have detected that our SCSI ID is on the bus,
- * SEL is true and BSY was false for at least one bus settle delay
- * (400 ns).
- *
- * We must assert BSY ourselves, until the target drops the SEL
- * signal.
- */
-
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_BSY);
- if (NCR5380_poll_politely(instance,
- STATUS_REG, SR_SEL, 0, 2 * HZ) < 0) {
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- return;
- }
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-
- /*
- * Wait for target to go into MSGIN.
- */
-
- if (NCR5380_poll_politely(instance,
- STATUS_REG, SR_REQ, SR_REQ, 2 * HZ) < 0) {
- do_abort(instance);
- return;
- }
-
-#if defined(CONFIG_SUN3)
- /* acknowledge toggle to MSGIN */
- NCR5380_write(TARGET_COMMAND_REG, PHASE_SR_TO_TCR(PHASE_MSGIN));
-
- /* peek at the byte without really hitting the bus */
- msg[0] = NCR5380_read(CURRENT_SCSI_DATA_REG);
-#else
- len = 1;
- data = msg;
- phase = PHASE_MSGIN;
- NCR5380_transfer_pio(instance, &phase, &len, &data);
-
- if (len) {
- do_abort(instance);
- return;
- }
-#endif
-
- if (!(msg[0] & 0x80)) {
- shost_printk(KERN_ERR, instance, "expecting IDENTIFY message, got ");
- spi_print_msg(msg);
- printk("\n");
- do_abort(instance);
- return;
- }
- lun = msg[0] & 0x07;
-
-#if defined(SUPPORT_TAGS) && !defined(CONFIG_SUN3)
- /* If the phase is still MSGIN, the target wants to send some more
- * messages. In case it supports tagged queuing, this is probably a
- * SIMPLE_QUEUE_TAG for the I_T_L_Q nexus.
- */
- tag = TAG_NONE;
- if (phase == PHASE_MSGIN && (hostdata->flags & FLAG_TAGGED_QUEUING)) {
- /* Accept previous IDENTIFY message by clearing ACK */
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- len = 2;
- data = msg + 1;
- if (!NCR5380_transfer_pio(instance, &phase, &len, &data) &&
- msg[1] == SIMPLE_QUEUE_TAG)
- tag = msg[2];
- dsprintk(NDEBUG_TAGS, instance, "reselect: target mask %02x, lun %d sent tag %d\n",
- target_mask, lun, tag);
- }
-#endif
-
- /*
- * Find the command corresponding to the I_T_L or I_T_L_Q nexus we
- * just reestablished, and remove it from the disconnected queue.
- */
-
- tmp = NULL;
- list_for_each_entry(ncmd, &hostdata->disconnected, list) {
- struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd);
-
- if (target_mask == (1 << scmd_id(cmd)) &&
- lun == (u8)cmd->device->lun
-#ifdef SUPPORT_TAGS
- && (tag == cmd->tag)
-#endif
- ) {
- list_del(&ncmd->list);
- tmp = cmd;
- break;
- }
- }
-
- if (tmp) {
- dsprintk(NDEBUG_RESELECTION | NDEBUG_QUEUES, instance,
- "reselect: removed %p from disconnected queue\n", tmp);
- } else {
-
-#ifdef SUPPORT_TAGS
- shost_printk(KERN_ERR, instance, "target bitmask 0x%02x lun %d tag %d not in disconnected queue.\n",
- target_mask, lun, tag);
-#else
- shost_printk(KERN_ERR, instance, "target bitmask 0x%02x lun %d not in disconnected queue.\n",
- target_mask, lun);
-#endif
- /*
- * Since we have an established nexus that we can't do anything
- * with, we must abort it.
- */
- do_abort(instance);
- return;
- }
-
-#if defined(CONFIG_SUN3)
- /* engage dma setup for the command we just saw */
- {
- void *d;
- unsigned long count;
-
- if (!tmp->SCp.this_residual && tmp->SCp.buffers_residual) {
- count = tmp->SCp.buffer->length;
- d = sg_virt(tmp->SCp.buffer);
- } else {
- count = tmp->SCp.this_residual;
- d = tmp->SCp.ptr;
- }
- /* setup this command for dma if not already */
- if (sun3_dma_setup_done != tmp &&
- sun3scsi_dma_xfer_len(count, tmp) > 0) {
- sun3scsi_dma_setup(instance, d, count,
- rq_data_dir(tmp->request));
- sun3_dma_setup_done = tmp;
- }
- }
-
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE | ICR_ASSERT_ACK);
-#endif
-
- /* Accept message by clearing ACK */
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
-
-#if defined(SUPPORT_TAGS) && defined(CONFIG_SUN3)
- /* If the phase is still MSGIN, the target wants to send some more
- * messages. In case it supports tagged queuing, this is probably a
- * SIMPLE_QUEUE_TAG for the I_T_L_Q nexus.
- */
- tag = TAG_NONE;
- if (phase == PHASE_MSGIN && setup_use_tagged_queuing) {
- /* Accept previous IDENTIFY message by clearing ACK */
- NCR5380_write(INITIATOR_COMMAND_REG, ICR_BASE);
- len = 2;
- data = msg + 1;
- if (!NCR5380_transfer_pio(instance, &phase, &len, &data) &&
- msg[1] == SIMPLE_QUEUE_TAG)
- tag = msg[2];
- dsprintk(NDEBUG_TAGS, instance, "reselect: target mask %02x, lun %d sent tag %d\n"
- target_mask, lun, tag);
- }
-#endif
-
- hostdata->connected = tmp;
- dsprintk(NDEBUG_RESELECTION, instance, "nexus established, target %d, lun %llu, tag %d\n",
- scmd_id(tmp), tmp->device->lun, tmp->tag);
-}
-
-
-/**
- * list_find_cmd - test for presence of a command in a linked list
- * @haystack: list of commands
- * @needle: command to search for
- */
-
-static bool list_find_cmd(struct list_head *haystack,
- struct scsi_cmnd *needle)
-{
- struct NCR5380_cmd *ncmd;
-
- list_for_each_entry(ncmd, haystack, list)
- if (NCR5380_to_scmd(ncmd) == needle)
- return true;
- return false;
-}
-
-/**
- * list_remove_cmd - remove a command from linked list
- * @haystack: list of commands
- * @needle: command to remove
- */
-
-static bool list_del_cmd(struct list_head *haystack,
- struct scsi_cmnd *needle)
-{
- if (list_find_cmd(haystack, needle)) {
- struct NCR5380_cmd *ncmd = scsi_cmd_priv(needle);
-
- list_del(&ncmd->list);
- return true;
- }
- return false;
-}
-
-/**
- * NCR5380_abort - scsi host eh_abort_handler() method
- * @cmd: the command to be aborted
- *
- * Try to abort a given command by removing it from queues and/or sending
- * the target an abort message. This may not succeed in causing a target
- * to abort the command. Nonetheless, the low-level driver must forget about
- * the command because the mid-layer reclaims it and it may be re-issued.
- *
- * The normal path taken by a command is as follows. For EH we trace this
- * same path to locate and abort the command.
- *
- * unissued -> selecting -> [unissued -> selecting ->]... connected ->
- * [disconnected -> connected ->]...
- * [autosense -> connected ->] done
- *
- * If cmd was not found at all then presumably it has already been completed,
- * in which case return SUCCESS to try to avoid further EH measures.
- *
- * If the command has not completed yet, we must not fail to find it.
- * We have no option but to forget the aborted command (even if it still
- * lacks sense data). The mid-layer may re-issue a command that is in error
- * recovery (see scsi_send_eh_cmnd), but the logic and data structures in
- * this driver are such that a command can appear on one queue only.
- *
- * The lock protects driver data structures, but EH handlers also use it
- * to serialize their own execution and prevent their own re-entry.
- */
-
-static int NCR5380_abort(struct scsi_cmnd *cmd)
-{
- struct Scsi_Host *instance = cmd->device->host;
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
- unsigned long flags;
- int result = SUCCESS;
-
- spin_lock_irqsave(&hostdata->lock, flags);
-
-#if (NDEBUG & NDEBUG_ANY)
- scmd_printk(KERN_INFO, cmd, __func__);
-#endif
- NCR5380_dprint(NDEBUG_ANY, instance);
- NCR5380_dprint_phase(NDEBUG_ANY, instance);
-
- if (list_del_cmd(&hostdata->unissued, cmd)) {
- dsprintk(NDEBUG_ABORT, instance,
- "abort: removed %p from issue queue\n", cmd);
- cmd->result = DID_ABORT << 16;
- cmd->scsi_done(cmd); /* No tag or busy flag to worry about */
- goto out;
- }
-
- if (hostdata->selecting == cmd) {
- dsprintk(NDEBUG_ABORT, instance,
- "abort: cmd %p == selecting\n", cmd);
- hostdata->selecting = NULL;
- cmd->result = DID_ABORT << 16;
- complete_cmd(instance, cmd);
- goto out;
- }
-
- if (list_del_cmd(&hostdata->disconnected, cmd)) {
- dsprintk(NDEBUG_ABORT, instance,
- "abort: removed %p from disconnected list\n", cmd);
- /* Can't call NCR5380_select() and send ABORT because that
- * means releasing the lock. Need a bus reset.
- */
- set_host_byte(cmd, DID_ERROR);
- complete_cmd(instance, cmd);
- result = FAILED;
- goto out;
- }
-
- if (hostdata->connected == cmd) {
- dsprintk(NDEBUG_ABORT, instance, "abort: cmd %p is connected\n", cmd);
- hostdata->connected = NULL;
- hostdata->dma_len = 0;
- if (do_abort(instance)) {
- set_host_byte(cmd, DID_ERROR);
- complete_cmd(instance, cmd);
- result = FAILED;
- goto out;
- }
- set_host_byte(cmd, DID_ABORT);
- complete_cmd(instance, cmd);
- goto out;
- }
-
- if (list_del_cmd(&hostdata->autosense, cmd)) {
- dsprintk(NDEBUG_ABORT, instance,
- "abort: removed %p from sense queue\n", cmd);
- set_host_byte(cmd, DID_ERROR);
- complete_cmd(instance, cmd);
- }
-
-out:
- if (result == FAILED)
- dsprintk(NDEBUG_ABORT, instance, "abort: failed to abort %p\n", cmd);
- else
- dsprintk(NDEBUG_ABORT, instance, "abort: successfully aborted %p\n", cmd);
-
- queue_work(hostdata->work_q, &hostdata->main_task);
- maybe_release_dma_irq(instance);
- spin_unlock_irqrestore(&hostdata->lock, flags);
-
- return result;
-}
-
-
-/**
- * NCR5380_bus_reset - reset the SCSI bus
- * @cmd: SCSI command undergoing EH
- *
- * Returns SUCCESS
- */
-
-static int NCR5380_bus_reset(struct scsi_cmnd *cmd)
-{
- struct Scsi_Host *instance = cmd->device->host;
- struct NCR5380_hostdata *hostdata = shost_priv(instance);
- int i;
- unsigned long flags;
- struct NCR5380_cmd *ncmd;
-
- spin_lock_irqsave(&hostdata->lock, flags);
-
-#if (NDEBUG & NDEBUG_ANY)
- scmd_printk(KERN_INFO, cmd, __func__);
-#endif
- NCR5380_dprint(NDEBUG_ANY, instance);
- NCR5380_dprint_phase(NDEBUG_ANY, instance);
-
- do_reset(instance);
-
- /* reset NCR registers */
- NCR5380_write(MODE_REG, MR_BASE);
- NCR5380_write(TARGET_COMMAND_REG, 0);
- NCR5380_write(SELECT_ENABLE_REG, 0);
-
- /* After the reset, there are no more connected or disconnected commands
- * and no busy units; so clear the low-level status here to avoid
- * conflicts when the mid-level code tries to wake up the affected
- * commands!
- */
-
- if (list_del_cmd(&hostdata->unissued, cmd)) {
- cmd->result = DID_RESET << 16;
- cmd->scsi_done(cmd);
- }
-
- if (hostdata->selecting) {
- hostdata->selecting->result = DID_RESET << 16;
- complete_cmd(instance, hostdata->selecting);
- hostdata->selecting = NULL;
- }
-
- list_for_each_entry(ncmd, &hostdata->disconnected, list) {
- struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd);
-
- set_host_byte(cmd, DID_RESET);
- cmd->scsi_done(cmd);
- }
- INIT_LIST_HEAD(&hostdata->disconnected);
-
- list_for_each_entry(ncmd, &hostdata->autosense, list) {
- struct scsi_cmnd *cmd = NCR5380_to_scmd(ncmd);
-
- set_host_byte(cmd, DID_RESET);
- cmd->scsi_done(cmd);
- }
- INIT_LIST_HEAD(&hostdata->autosense);
-
- if (hostdata->connected) {
- set_host_byte(hostdata->connected, DID_RESET);
- complete_cmd(instance, hostdata->connected);
- hostdata->connected = NULL;
- }
-
-#ifdef SUPPORT_TAGS
- free_all_tags(hostdata);
-#endif
- for (i = 0; i < 8; ++i)
- hostdata->busy[i] = 0;
- hostdata->dma_len = 0;
-
- queue_work(hostdata->work_q, &hostdata->main_task);
- maybe_release_dma_irq(instance);
- spin_unlock_irqrestore(&hostdata->lock, flags);
-
- return SUCCESS;
-}