Re: [PATCH v2 12/18] dt-bindings: Add PLX Technology OXNAS pinctrl and gpio bindings

[Rob Herring]

On Wed, Mar 09, 2016 at 11:24:14AM +0100, Neil Armstrong wrote:
> Signed-off-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
> ---
>  .../devicetree/bindings/gpio/gpio_oxnas.txt        |  27 ++++++
>  .../bindings/pinctrl/plxtech,pinctrl.txt           | 100 +++++++++++++++++++++
>  2 files changed, 127 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/gpio/gpio_oxnas.txt
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/plxtech,pinctrl.txt
> 
> diff --git a/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt
> new file mode 100644
> index 0000000..cbb03c4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/gpio_oxnas.txt
> @@ -0,0 +1,27 @@
> +PLX Technology OXNAS SoC GPIO Controller
> +==========================================
> +
> +Required properties:
> +- compatible: "oxsemi,ox810se-gpio".
> +- reg: Should contain GPIO controller registers location and length
> +- interrupts: Should be the port interrupt shared by all the pins.
> +- #gpio-cells: Should be two.  The first cell is the pin number and
> +  the second cell is used to specify optional parameters (currently
> +  unused).
> +- gpio-controller: Marks the device node as a GPIO controller.
> +
> +optional properties:
> +- #gpio-lines: Number of gpio if absent 32.
> +
> +
> +Example:
> +	gpio0: gpio@000000 {

Drop the leading 0s.

> +		compatible = "oxsemi,ox810se-gpio";
> +		reg = <0x000000 0x100000>;
> +		interrupts = <21>;
> +		#gpio-cells = <2>;
> +		gpio-controller;
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		#gpio-lines = <32>;
> +	};
> diff --git a/Documentation/devicetree/bindings/pinctrl/plxtech,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/plxtech,pinctrl.txt
> new file mode 100644
> index 0000000..0c5051a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/plxtech,pinctrl.txt
> @@ -0,0 +1,100 @@
> +PLX Technology OXNAS SoC Pinmux Controller
> +==========================================
> +
> +The OXNAS Pinmux Controller, enables the IC to share one PAD to several
> +functional blocks. The sharing is done by multiplexing the PAD input/output
> +signals. For each PAD there are up to 8 muxing options (called periph modes).
> +Since different modules require different PAD settings
> +(like pull up, keeper, etc) the contoller controls also the PAD settings
> +parameters.
> +
> +Please refer to pinctrl-bindings.txt in this directory for details of the
> +common pinctrl bindings used by client devices, including the meaning of the
> +phrase "pin configuration node".
> +
> +OXNAS pin configuration node is a node of a group of pins which can be
> +used for a specific device or function. This node represents both mux and config
> +of the pins in that group. The 'pins' selects the function mode(also named pin
> +mode) this pin can work on and the 'config' configures various pad settings
> +such as pull-up, multi drive, etc.
> +
> +Required properties for iomux controller:
> +- compatible: "oxsemi,ox810se-pinctrl"
> +- plxtech,mux-mask: array of mask (periph per bank) to describe if a pin can be
> +  configured in this periph mode. All the periph and bank need to be describe.
> +- plxtech,sys-ctrl: a phandle to the system controller syscon node
> +
> +How to create such array:
> +
> +Each column will represent the possible peripheral of the pinctrl
> +Each line will represent a pio bank
> +
> +For example :
> +Peripheral: 2 ( A and B)
> +Bank: 2 (A, B and C)
> +=>
> +
> +  /*    A         B     */
> +  0xffffffff 0xffc00c3b  /* pioA */
> +  0xffffffff 0x7fff3ccf  /* pioB */
> +
> +For each peripheral/bank we will descibe in a u32 if a pin can be
> +configured in it by putting 1 to the pin bit (1 << pin)
> +
> +Required properties for pin configuration node:
> +- plxtech,pins: 4 integers array, represents a group of pins mux and config
> +  setting. The format is plxtech,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>.
> +  The PERIPH 0 means gpio, PERIPH 1 is periph A, PERIPH 2 is periph B...
> +  PIN_BANK 0 is pioA, PIN_BANK 1 is pioB...
> +
> +Bits used for CONFIG:
> + - None Yet
> +
> +Examples:
> +
> +pinctrl: pinctrl {
> +	compatible = "oxsemi,ox810se-pinctrl", "simple-bus";
> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +	ranges;
> +
> +	/* Regmap for sys registers */
> +	plxtech,sys-ctrl = <&sys>;
> +
> +	/* Default, all-open mux-map */
> +	plxtech,mux-mask = <
> +		 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF
> +		 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF
> +		 >;
> +
> +	uart0 {
> +		pinctrl_uart0: uart0 {
> +			plxtech,pins = <0 31 3 0
> +					0 32 3 0>;
> +		};
> +		pinctrl_uart0_modem: uart0_modem {
> +			plxtech,pins = <0 27 3 0
> +					0 28 3 0
> +					0 29 3 0
> +					0 30 3 0
> +					0 33 3 0
> +					0 34 3 0>;
> +		};
> +	};
> +};
> +
> +uart0: uart@200000 {

serial@200000

With those changes:

Acked-by: Rob Herring <robh@xxxxxxxxxx>