[PATCH v4 05/14] i2c-octeon: Enable high-level controller and improve on bus contention
From: Jan Glauber
Date: Fri Mar 18 2016 - 04:51:04 EST
From: David Daney <david.daney@xxxxxxxxxx>
Use High Level Controller when possible.
i2c-octeon was reacting badly to bus contention: when in
direct-access mode (for transfers > 8 bytes, which cannot use the
high-level controller) some !ACK or arbitration-loss states were
not causing the current transfer to be aborted, and the bus released.
There's one place in i2c protocol that !ACK is an acceptable
response: in the final byte of a read cycle. In this case the
destination is not saying that the transfer failed, just that it
doesn't want more data.
This enables correct behavior of ACK on final byte of non-final read
msgs too.
Signed-off-by: David Daney <ddaney@xxxxxxxxxxxxxxxxxx>
Signed-off-by: Jan Glauber <jglauber@xxxxxxxxxx>
---
drivers/i2c/busses/i2c-octeon.c | 783 ++++++++++++++++++++++++++++++++--------
1 file changed, 629 insertions(+), 154 deletions(-)
diff --git a/drivers/i2c/busses/i2c-octeon.c b/drivers/i2c/busses/i2c-octeon.c
index c21d102..0e3611a 100644
--- a/drivers/i2c/busses/i2c-octeon.c
+++ b/drivers/i2c/busses/i2c-octeon.c
@@ -29,13 +29,23 @@
/* Register offsets */
#define SW_TWSI 0x00
#define TWSI_INT 0x10
+#define SW_TWSI_EXT 0x18
/* Controller command patterns */
#define SW_TWSI_V BIT_ULL(63) /* Valid bit */
+#define SW_TWSI_EIA BIT_ULL(61) /* Extended internal address */
#define SW_TWSI_R BIT_ULL(56) /* Result or read bit */
+#define SW_TWSI_SOVR BIT_ULL(55) /* Size override */
+#define SW_TWSI_SIZE_SHIFT 52
+#define SW_TWSI_ADDR_SHIFT 40
+#define SW_TWSI_IA_SHIFT 32 /* Internal address */
/* Controller opcode word (bits 60:57) */
#define SW_TWSI_OP_SHIFT 57
+#define SW_TWSI_OP_7 (0ULL << SW_TWSI_OP_SHIFT)
+#define SW_TWSI_OP_7_IA (1ULL << SW_TWSI_OP_SHIFT)
+#define SW_TWSI_OP_10 (2ULL << SW_TWSI_OP_SHIFT)
+#define SW_TWSI_OP_10_IA (3ULL << SW_TWSI_OP_SHIFT)
#define SW_TWSI_OP_TWSI_CLK (4ULL << SW_TWSI_OP_SHIFT)
#define SW_TWSI_OP_EOP (6ULL << SW_TWSI_OP_SHIFT) /* Extended opcode */
@@ -48,7 +58,7 @@
#define SW_TWSI_EOP_TWSI_RST (SW_TWSI_OP_EOP | 7ULL << SW_TWSI_EOP_SHIFT)
/* Controller command and status bits */
-#define TWSI_CTL_CE 0x80
+#define TWSI_CTL_CE 0x80 /* High level controller enable */
#define TWSI_CTL_ENAB 0x40 /* Bus enable */
#define TWSI_CTL_STA 0x20 /* Master-mode start, HW clears when done */
#define TWSI_CTL_STP 0x10 /* Master-mode stop, HW clears when done */
@@ -56,18 +66,47 @@
#define TWSI_CTL_AAK 0x04 /* Assert ACK */
/* Some status values */
+#define STAT_ERROR 0x00
#define STAT_START 0x08
#define STAT_RSTART 0x10
#define STAT_TXADDR_ACK 0x18
+#define STAT_TXADDR_NAK 0x20
#define STAT_TXDATA_ACK 0x28
+#define STAT_TXDATA_NAK 0x30
+#define STAT_LOST_ARB_38 0x38
#define STAT_RXADDR_ACK 0x40
+#define STAT_RXADDR_NAK 0x48
#define STAT_RXDATA_ACK 0x50
+#define STAT_RXDATA_NAK 0x58
+#define STAT_SLAVE_60 0x60
+#define STAT_LOST_ARB_68 0x68
+#define STAT_SLAVE_70 0x70
+#define STAT_LOST_ARB_78 0x78
+#define STAT_SLAVE_80 0x80
+#define STAT_SLAVE_88 0x88
+#define STAT_GENDATA_ACK 0x90
+#define STAT_GENDATA_NAK 0x98
+#define STAT_SLAVE_A0 0xA0
+#define STAT_SLAVE_A8 0xA8
+#define STAT_LOST_ARB_B0 0xB0
+#define STAT_SLAVE_LOST 0xB8
+#define STAT_SLAVE_NAK 0xC0
+#define STAT_SLAVE_ACK 0xC8
+#define STAT_AD2W_ACK 0xD0
+#define STAT_AD2W_NAK 0xD8
#define STAT_IDLE 0xF8
/* TWSI_INT values */
+#define TWSI_INT_ST_INT BIT_ULL(0)
+#define TWSI_INT_TS_INT BIT_ULL(1)
+#define TWSI_INT_CORE_INT BIT_ULL(2)
+#define TWSI_INT_ST_EN BIT_ULL(4)
+#define TWSI_INT_TS_EN BIT_ULL(5)
#define TWSI_INT_CORE_EN BIT_ULL(6)
#define TWSI_INT_SDA_OVR BIT_ULL(8)
#define TWSI_INT_SCL_OVR BIT_ULL(9)
+#define TWSI_INT_SDA BIT_ULL(10)
+#define TWSI_INT_SCL BIT_ULL(11)
struct octeon_i2c {
wait_queue_head_t queue;
@@ -77,8 +116,11 @@ struct octeon_i2c {
int sys_freq;
void __iomem *twsi_base;
struct device *dev;
+ bool hlc_enabled;
};
+static int reset_how;
+
/**
* octeon_i2c_write_sw - write an I2C core register
* @i2c: The struct octeon_i2c
@@ -87,7 +129,7 @@ struct octeon_i2c {
*
* The I2C core registers are accessed indirectly via the SW_TWSI CSR.
*/
-static void octeon_i2c_write_sw(struct octeon_i2c *i2c, u64 eop_reg, u8 data)
+static void octeon_i2c_write_sw(struct octeon_i2c *i2c, u64 eop_reg, u32 data)
{
u64 tmp;
@@ -98,7 +140,7 @@ static void octeon_i2c_write_sw(struct octeon_i2c *i2c, u64 eop_reg, u8 data)
}
/**
- * octeon_i2c_read_sw - read lower bits of an I2C core register
+ * octeon_i2c_read_sw64 - read an I2C core register
* @i2c: The struct octeon_i2c
* @eop_reg: Register selector
*
@@ -106,7 +148,7 @@ static void octeon_i2c_write_sw(struct octeon_i2c *i2c, u64 eop_reg, u8 data)
*
* The I2C core registers are accessed indirectly via the SW_TWSI CSR.
*/
-static u8 octeon_i2c_read_sw(struct octeon_i2c *i2c, u64 eop_reg)
+static u64 octeon_i2c_read_sw64(struct octeon_i2c *i2c, u64 eop_reg)
{
u64 tmp;
@@ -115,7 +157,21 @@ static u8 octeon_i2c_read_sw(struct octeon_i2c *i2c, u64 eop_reg)
tmp = __raw_readq(i2c->twsi_base + SW_TWSI);
} while ((tmp & SW_TWSI_V) != 0);
- return tmp & 0xFF;
+ return tmp;
+}
+
+/**
+ * octeon_i2c_read_sw - read lower bits of an I2C core register
+ * @i2c: The struct octeon_i2c
+ * @eop_reg: Register selector
+ *
+ * Returns the data.
+ *
+ * The I2C core registers are accessed indirectly via the SW_TWSI CSR.
+ */
+static u8 octeon_i2c_read_sw(struct octeon_i2c *i2c, u64 eop_reg)
+{
+ return octeon_i2c_read_sw64(i2c, eop_reg) & 0xFF;
}
/**
@@ -148,6 +204,15 @@ static void octeon_i2c_int_disable(struct octeon_i2c *i2c)
octeon_i2c_write_int(i2c, 0);
}
+static void octeon_i2c_disable_hlc(struct octeon_i2c *i2c)
+{
+ if (!i2c->hlc_enabled)
+ return;
+
+ i2c->hlc_enabled = false;
+ octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, TWSI_CTL_ENAB);
+}
+
/**
* octeon_i2c_unblock - unblock the bus
* @i2c: The struct octeon_i2c
@@ -157,13 +222,18 @@ static void octeon_i2c_int_disable(struct octeon_i2c *i2c)
*/
static void octeon_i2c_unblock(struct octeon_i2c *i2c)
{
- int i;
+ int state, i;
+ octeon_i2c_disable_hlc(i2c);
dev_dbg(i2c->dev, "%s\n", __func__);
+ /* cycle 8+1 clocks with SDA high */
for (i = 0; i < 9; i++) {
octeon_i2c_write_int(i2c, 0);
udelay(5);
+ state = __raw_readq(i2c->twsi_base + TWSI_INT);
+ if (state & (TWSI_INT_SDA | TWSI_INT_SCL))
+ break;
octeon_i2c_write_int(i2c, TWSI_INT_SCL_OVR);
udelay(5);
}
@@ -186,10 +256,14 @@ static irqreturn_t octeon_i2c_isr(int irq, void *dev_id)
return IRQ_HANDLED;
}
+static u64 octeon_i2c_read_ctl(struct octeon_i2c *i2c)
+{
+ return octeon_i2c_read_sw64(i2c, SW_TWSI_EOP_TWSI_CTL);
+}
static int octeon_i2c_test_iflg(struct octeon_i2c *i2c)
{
- return (octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_CTL) & TWSI_CTL_IFLG) != 0;
+ return (octeon_i2c_read_ctl(i2c) & TWSI_CTL_IFLG) != 0;
}
/**
@@ -214,46 +288,96 @@ static int octeon_i2c_wait(struct octeon_i2c *i2c)
return 0;
}
-/**
- * octeon_i2c_start - send START to the bus
- * @i2c: The struct octeon_i2c
- *
- * Returns 0 on success, otherwise a negative errno.
+/*
+ * Cleanup low-level state & enable high-level.
+ * Returns -EAGAIN if low-level state could not be cleaned.
*/
-static int octeon_i2c_start(struct octeon_i2c *i2c)
+static int octeon_i2c_enable_hlc(struct octeon_i2c *i2c)
{
- int result;
- u8 data;
+ int try = 0, ret = 0;
+ u64 val;
+
+ if (i2c->hlc_enabled)
+ return 0;
+ i2c->hlc_enabled = true;
+
+ while (1) {
+ val = octeon_i2c_read_ctl(i2c) & (TWSI_CTL_STA | TWSI_CTL_STP);
+ if (!val)
+ break;
+
+ /* clear IFLG event */
+ if (val & TWSI_CTL_IFLG)
+ octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, TWSI_CTL_ENAB);
+
+ if (try++ > 100) {
+ pr_err("%s: giving up\n", __func__);
+ ret = -EAGAIN;
+ break;
+ }
+
+ /* spin until any start/stop has finished */
+ udelay(10);
+ }
octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL,
- TWSI_CTL_ENAB | TWSI_CTL_STA);
+ TWSI_CTL_CE | TWSI_CTL_AAK | TWSI_CTL_ENAB);
+ return ret;
+}
- result = octeon_i2c_wait(i2c);
- if (result) {
- if (octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_STAT) == STAT_IDLE) {
- /*
- * Controller refused to send start flag May
- * be a client is holding SDA low - let's try
- * to free it.
- */
- octeon_i2c_unblock(i2c);
- octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL,
- TWSI_CTL_ENAB | TWSI_CTL_STA);
- result = octeon_i2c_wait(i2c);
- }
- if (result)
- return result;
- }
+static int octeon_i2c_lost_arb(u8 code, int final_read)
+{
+ switch (code) {
+ /* Arbitration lost */
+ case STAT_LOST_ARB_38:
+ case STAT_LOST_ARB_68:
+ case STAT_LOST_ARB_78:
+ case STAT_LOST_ARB_B0:
+ return -EAGAIN;
+
+ /* Being addressed as slave, should back off & listen */
+ case STAT_SLAVE_60:
+ case STAT_SLAVE_70:
+ case STAT_GENDATA_ACK:
+ case STAT_GENDATA_NAK:
+ return -EIO;
- data = octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_STAT);
- if ((data != STAT_START) && (data != STAT_RSTART)) {
- dev_err(i2c->dev, "%s: bad status (0x%x)\n", __func__, data);
+ /* Core busy as slave */
+ case STAT_SLAVE_80:
+ case STAT_SLAVE_88:
+ case STAT_SLAVE_A0:
+ case STAT_SLAVE_A8:
+ case STAT_SLAVE_LOST:
+ case STAT_SLAVE_NAK:
+ case STAT_SLAVE_ACK:
return -EIO;
- }
+ /* ACK allowed on pre-terminal bytes only */
+ case STAT_RXDATA_ACK:
+ if (!final_read)
+ return 0;
+ return -EAGAIN;
+
+ /* NAK allowed on terminal byte only */
+ case STAT_RXDATA_NAK:
+ if (final_read)
+ return 0;
+ return -EAGAIN;
+ case STAT_TXDATA_NAK:
+ case STAT_TXADDR_NAK:
+ case STAT_RXADDR_NAK:
+ case STAT_AD2W_NAK:
+ return -EAGAIN;
+ }
return 0;
}
+static int check_arb(struct octeon_i2c *i2c, int final_read)
+{
+ return octeon_i2c_lost_arb(octeon_i2c_read_sw(i2c,
+ SW_TWSI_EOP_TWSI_STAT), final_read);
+}
+
/* send STOP to the bus */
static void octeon_i2c_stop(struct octeon_i2c *i2c)
{
@@ -261,52 +385,398 @@ static void octeon_i2c_stop(struct octeon_i2c *i2c)
TWSI_CTL_ENAB | TWSI_CTL_STP);
}
+static bool octeon_i2c_hlc_test_ready(struct octeon_i2c *i2c)
+{
+ u64 val = __raw_readq(i2c->twsi_base + SW_TWSI);
+
+ return (val & SW_TWSI_V) == 0;
+}
+
+static void octeon_i2c_hlc_int_enable(struct octeon_i2c *i2c)
+{
+ octeon_i2c_write_int(i2c, TWSI_INT_ST_EN);
+}
+
+static void octeon_i2c_hlc_int_clear(struct octeon_i2c *i2c)
+{
+ /* clear ST/TS events, listen for neither */
+ octeon_i2c_write_int(i2c, TWSI_INT_ST_INT | TWSI_INT_TS_INT);
+}
+
/**
- * octeon_i2c_write - send data to the bus via low-level controller
+ * octeon_i2c_hlc_wait - wait for an HLC operation to complete
* @i2c: The struct octeon_i2c
- * @target: Target address
- * @data: Pointer to the data to be sent
- * @length: Length of the data
- *
- * The address is sent over the bus, then the data.
*
* Returns 0 on success, otherwise a negative errno.
*/
-static int octeon_i2c_write(struct octeon_i2c *i2c, int target,
- const u8 *data, int length)
+static int octeon_i2c_hlc_wait(struct octeon_i2c *i2c)
{
- int i, result;
- u8 tmp;
+ int time_left;
- result = octeon_i2c_start(i2c);
- if (result)
- return result;
+ octeon_i2c_hlc_int_enable(i2c);
+ time_left = wait_event_interruptible_timeout(i2c->queue,
+ octeon_i2c_hlc_test_ready(i2c),
+ i2c->adap.timeout);
+ octeon_i2c_int_disable(i2c);
+ if (!time_left) {
+ octeon_i2c_hlc_int_clear(i2c);
+ dev_dbg(i2c->dev, "%s: timeout\n", __func__);
+ return -ETIMEDOUT;
+ }
- octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_DATA, target << 1);
- octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, TWSI_CTL_ENAB);
+ if (time_left < 0) {
+ dev_dbg(i2c->dev, "%s: wait interrupted\n", __func__);
+ return time_left;
+ }
+ return 0;
+}
- result = octeon_i2c_wait(i2c);
- if (result)
- return result;
+/* high-level-controller pure read of up to 8 bytes */
+static int octeon_i2c_simple_read(struct octeon_i2c *i2c, struct i2c_msg *msgs)
+{
+ int i, j, ret = 0;
+ u64 cmd;
+
+ octeon_i2c_enable_hlc(i2c);
+ cmd = SW_TWSI_V | SW_TWSI_R | SW_TWSI_SOVR;
+ /* SIZE */
+ cmd |= (u64) (msgs[0].len - 1) << SW_TWSI_SIZE_SHIFT;
+ /* A */
+ cmd |= (u64) (msgs[0].addr & 0x7full) << SW_TWSI_ADDR_SHIFT;
+
+ if (msgs[0].flags & I2C_M_TEN)
+ cmd |= SW_TWSI_OP_10;
+ else
+ cmd |= SW_TWSI_OP_7;
+
+ octeon_i2c_hlc_int_clear(i2c);
+ __raw_writeq(cmd, i2c->twsi_base + SW_TWSI);
+
+ ret = octeon_i2c_hlc_wait(i2c);
+ if (ret)
+ goto err;
+
+ cmd = __raw_readq(i2c->twsi_base + SW_TWSI);
+ if ((cmd & SW_TWSI_R) == 0)
+ return -EAGAIN;
+
+ for (i = 0, j = msgs[0].len - 1; i < msgs[0].len && i < 4; i++, j--)
+ msgs[0].buf[j] = (cmd >> (8 * i)) & 0xff;
+
+ if (msgs[0].len > 4) {
+ cmd = __raw_readq(i2c->twsi_base + SW_TWSI_EXT);
+ for (i = 0; i < msgs[0].len - 4 && i < 4; i++, j--)
+ msgs[0].buf[j] = (cmd >> (8 * i)) & 0xff;
+ }
- for (i = 0; i < length; i++) {
- tmp = octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_STAT);
+err:
+ return ret;
+}
+
+/* high-level-controller pure write of up to 8 bytes */
+static int octeon_i2c_simple_write(struct octeon_i2c *i2c, struct i2c_msg *msgs)
+{
+ int i, j, ret = 0;
+ u64 cmd;
+
+ octeon_i2c_enable_hlc(i2c);
+ octeon_i2c_hlc_int_clear(i2c);
+
+ ret = check_arb(i2c, false);
+ if (ret)
+ goto err;
+
+ cmd = SW_TWSI_V | SW_TWSI_SOVR;
+ /* SIZE */
+ cmd |= (u64) (msgs[0].len - 1) << SW_TWSI_SIZE_SHIFT;
+ /* A */
+ cmd |= (u64) (msgs[0].addr & 0x7full) << SW_TWSI_ADDR_SHIFT;
+
+ if (msgs[0].flags & I2C_M_TEN)
+ cmd |= SW_TWSI_OP_10;
+ else
+ cmd |= SW_TWSI_OP_7;
+
+ for (i = 0, j = msgs[0].len - 1; i < msgs[0].len && i < 4; i++, j--)
+ cmd |= (u64)msgs[0].buf[j] << (8 * i);
+
+ if (msgs[0].len > 4) {
+ u64 ext = 0;
+
+ for (i = 0; i < msgs[0].len - 4 && i < 4; i++, j--)
+ ext |= (u64) msgs[0].buf[j] << (8 * i);
+ __raw_writeq(ext, i2c->twsi_base + SW_TWSI_EXT);
+ }
+
+ __raw_writeq(cmd, i2c->twsi_base + SW_TWSI);
+
+ ret = octeon_i2c_hlc_wait(i2c);
+ if (ret)
+ goto err;
+
+ cmd = __raw_readq(i2c->twsi_base + SW_TWSI);
+ if ((cmd & SW_TWSI_R) == 0)
+ return -EAGAIN;
+
+ ret = check_arb(i2c, false);
+
+err:
+ return ret;
+}
+
+/* high-level-controller composite write+read, msg0=addr, msg1=data */
+static int octeon_i2c_ia_read(struct octeon_i2c *i2c, struct i2c_msg *msgs)
+{
+ int i, j, ret = 0;
+ u64 cmd;
+
+ octeon_i2c_enable_hlc(i2c);
+
+ cmd = SW_TWSI_V | SW_TWSI_R | SW_TWSI_SOVR;
+ /* SIZE */
+ cmd |= (u64)(msgs[1].len - 1) << SW_TWSI_SIZE_SHIFT;
+ /* A */
+ cmd |= (u64)(msgs[0].addr & 0x7full) << SW_TWSI_ADDR_SHIFT;
+
+ if (msgs[0].flags & I2C_M_TEN)
+ cmd |= SW_TWSI_OP_10_IA;
+ else
+ cmd |= SW_TWSI_OP_7_IA;
+
+ if (msgs[0].len == 2) {
+ u64 ext = 0;
+
+ cmd |= SW_TWSI_EIA;
+ ext = (u64) msgs[0].buf[0] << SW_TWSI_IA_SHIFT;
+ cmd |= (u64) msgs[0].buf[1] << SW_TWSI_IA_SHIFT;
+ __raw_writeq(ext, i2c->twsi_base + SW_TWSI_EXT);
+ } else
+ cmd |= (u64) msgs[0].buf[0] << SW_TWSI_IA_SHIFT;
+
+ octeon_i2c_hlc_int_clear(i2c);
+ __raw_writeq(cmd, i2c->twsi_base + SW_TWSI);
+
+ ret = octeon_i2c_hlc_wait(i2c);
+ if (ret)
+ goto err;
+
+ cmd = __raw_readq(i2c->twsi_base + SW_TWSI);
+ if ((cmd & SW_TWSI_R) == 0)
+ return -EAGAIN;
+
+ for (i = 0, j = msgs[1].len - 1; i < msgs[1].len && i < 4; i++, j--)
+ msgs[1].buf[j] = (cmd >> (8 * i)) & 0xff;
+
+ if (msgs[1].len > 4) {
+ cmd = __raw_readq(i2c->twsi_base + SW_TWSI_EXT);
+ for (i = 0; i < msgs[1].len - 4 && i < 4; i++, j--)
+ msgs[1].buf[j] = (cmd >> (8 * i)) & 0xff;
+ }
+
+err:
+ return ret;
+}
+
+/* high-level-controller composite write+write, m[0]len<=2, m[1]len<=8 */
+static int octeon_i2c_ia_write(struct octeon_i2c *i2c, struct i2c_msg *msgs)
+{
+ bool set_ext = false;
+ int i, j, ret = 0;
+ u64 cmd, ext = 0;
+
+ octeon_i2c_enable_hlc(i2c);
+
+ cmd = SW_TWSI_V | SW_TWSI_SOVR;
+ /* SIZE */
+ cmd |= (u64) (msgs[1].len - 1) << SW_TWSI_SIZE_SHIFT;
+ /* A */
+ cmd |= (u64) (msgs[0].addr & 0x7full) << SW_TWSI_ADDR_SHIFT;
+
+ if (msgs[0].flags & I2C_M_TEN)
+ cmd |= SW_TWSI_OP_10_IA;
+ else
+ cmd |= SW_TWSI_OP_7_IA;
+
+ if (msgs[0].len == 2) {
+ cmd |= SW_TWSI_EIA;
+ ext |= (u64) msgs[0].buf[0] << SW_TWSI_IA_SHIFT;
+ set_ext = true;
+ cmd |= (u64) msgs[0].buf[1] << SW_TWSI_IA_SHIFT;
+ } else
+ cmd |= (u64) msgs[0].buf[0] << SW_TWSI_IA_SHIFT;
+
+ for (i = 0, j = msgs[1].len - 1; i < msgs[1].len && i < 4; i++, j--)
+ cmd |= (u64) msgs[1].buf[j] << (8 * i);
+
+ if (msgs[1].len > 4) {
+ for (i = 0; i < msgs[1].len - 4 && i < 4; i++, j--)
+ ext |= (u64)msgs[1].buf[j] << (8 * i);
+ set_ext = true;
+ }
+ if (set_ext)
+ __raw_writeq(ext, i2c->twsi_base + SW_TWSI_EXT);
+
+ octeon_i2c_hlc_int_clear(i2c);
+ __raw_writeq(cmd, i2c->twsi_base + SW_TWSI);
+
+ ret = octeon_i2c_hlc_wait(i2c);
+ if (ret)
+ goto err;
+
+ cmd = octeon_i2c_read_sw64(i2c, SW_TWSI_EOP_TWSI_STAT);
+ if ((cmd & SW_TWSI_R) == 0)
+ return -EAGAIN;
+ ret = octeon_i2c_lost_arb(cmd, false);
+
+err:
+ return ret;
+}
+
+/* calculate and set clock divisors */
+static void octeon_i2c_set_clock(struct octeon_i2c *i2c)
+{
+ int tclk, thp_base, inc, thp_idx, mdiv_idx, ndiv_idx, foscl, diff;
+ int thp = 0x18, mdiv = 2, ndiv = 0, delta_hz = 1000000;
- if ((tmp != STAT_TXADDR_ACK) && (tmp != STAT_TXDATA_ACK)) {
- dev_err(i2c->dev,
- "%s: bad status before write (0x%x)\n",
- __func__, tmp);
- return -EIO;
+ for (ndiv_idx = 0; ndiv_idx < 8 && delta_hz != 0; ndiv_idx++) {
+ /*
+ * An mdiv value of less than 2 seems to not work well
+ * with ds1337 RTCs, so we constrain it to larger values.
+ */
+ for (mdiv_idx = 15; mdiv_idx >= 2 && delta_hz != 0; mdiv_idx--) {
+ /*
+ * For given ndiv and mdiv values check the
+ * two closest thp values.
+ */
+ tclk = i2c->twsi_freq * (mdiv_idx + 1) * 10;
+ tclk *= (1 << ndiv_idx);
+ thp_base = (i2c->sys_freq / (tclk * 2)) - 1;
+
+ for (inc = 0; inc <= 1; inc++) {
+ thp_idx = thp_base + inc;
+ if (thp_idx < 5 || thp_idx > 0xff)
+ continue;
+
+ foscl = i2c->sys_freq / (2 * (thp_idx + 1));
+ foscl = foscl / (1 << ndiv_idx);
+ foscl = foscl / (mdiv_idx + 1) / 10;
+ diff = abs(foscl - i2c->twsi_freq);
+ if (diff < delta_hz) {
+ delta_hz = diff;
+ thp = thp_idx;
+ mdiv = mdiv_idx;
+ ndiv = ndiv_idx;
+ }
+ }
}
+ }
+ octeon_i2c_write_sw(i2c, SW_TWSI_OP_TWSI_CLK, thp);
+ octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CLKCTL, (mdiv << 3) | ndiv);
+}
- octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_DATA, data[i]);
- octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, TWSI_CTL_ENAB);
+static int octeon_i2c_init_lowlevel(struct octeon_i2c *i2c)
+{
+ u8 status = 0;
+ int tries;
- result = octeon_i2c_wait(i2c);
- if (result)
- return result;
+ /* reset controller */
+ octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_RST, 0);
+
+ for (tries = 10; tries && status != STAT_IDLE; tries--) {
+ udelay(1);
+ status = octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_STAT);
}
+ if (status != STAT_IDLE) {
+ dev_err(i2c->dev, "%s: TWSI_RST failed! (0x%x)\n",
+ __func__, status);
+ return -EIO;
+ }
+
+ /* toggle twice to force both teardowns */
+ octeon_i2c_enable_hlc(i2c);
+ octeon_i2c_disable_hlc(i2c);
+ return 0;
+}
+
+/*
+ * TWSI state seems stuck. Not sure if it's TWSI-engine state or something
+ * else on bus. The initial _stop() is always harmless, it just resets state
+ * machine, does not _transmit_ STOP unless engine was active.
+ */
+static int start_unstick(struct octeon_i2c *i2c)
+{
+ octeon_i2c_stop(i2c);
+
+ /*
+ * Response is escalated over successive calls,
+ * as EAGAIN provokes retries from i2c/core.
+ */
+ switch (reset_how++ % 4) {
+ case 0:
+ /* just the stop above */
+ break;
+ case 1:
+ /*
+ * Controller refused to send start flag. May be a
+ * client is holding SDA low? Let's try to free it.
+ */
+ octeon_i2c_unblock(i2c);
+ break;
+ case 2:
+ /* re-init our TWSI hardware */
+ octeon_i2c_init_lowlevel(i2c);
+ break;
+ default:
+ /* retry in caller */
+ reset_how = 0;
+ return -EAGAIN;
+ }
+ return 0;
+}
+
+/**
+ * octeon_i2c_start - send START to the bus
+ * @i2c: The struct octeon_i2c
+ * @first: first msg in combined operation?
+ *
+ * Returns 0 on success, otherwise a negative errno.
+ */
+static int octeon_i2c_start(struct octeon_i2c *i2c, int first)
+{
+ int result;
+ u8 data;
+
+ octeon_i2c_disable_hlc(i2c);
+
+ while (1) {
+ octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL,
+ TWSI_CTL_ENAB | TWSI_CTL_STA);
+
+ result = octeon_i2c_wait(i2c);
+ data = octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_STAT);
+
+ switch (data) {
+ case STAT_START:
+ case STAT_RSTART:
+ if (!first)
+ return -EAGAIN;
+ reset_how = 0;
+ return 0;
+ case STAT_RXADDR_ACK:
+ if (first)
+ return -EAGAIN;
+ return start_unstick(i2c);
+ /*
+ * case STAT_IDLE:
+ * case STAT_ERROR:
+ */
+ default:
+ if (!first)
+ return -EAGAIN;
+ start_unstick(i2c);
+ }
+ }
return 0;
}
@@ -316,54 +786,51 @@ static int octeon_i2c_write(struct octeon_i2c *i2c, int target,
* @target: Target address
* @data: Pointer to the location to store the data
* @rlength: Length of the data
+ * @phase: which phase of a combined operation.
* @recv_len: flag for length byte
*
* The address is sent over the bus, then the data is read.
*
* Returns 0 on success, otherwise a negative errno.
*/
-static int octeon_i2c_read(struct octeon_i2c *i2c, int target,
- u8 *data, u16 *rlength, bool recv_len)
+static int octeon_i2c_read(struct octeon_i2c *i2c, int target, u8 *data,
+ u16 *rlength, bool first, bool last, bool recv_len)
{
+ u8 ctl = TWSI_CTL_ENAB | TWSI_CTL_AAK;
int i, result, length = *rlength;
u8 tmp;
if (length < 1)
return -EINVAL;
- result = octeon_i2c_start(i2c);
+ result = octeon_i2c_start(i2c, first);
if (result)
return result;
octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_DATA, (target << 1) | 1);
- octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, TWSI_CTL_ENAB);
-
- result = octeon_i2c_wait(i2c);
- if (result)
- return result;
- for (i = 0; i < length; i++) {
+ for (i = 0; i < length; ) {
tmp = octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_STAT);
+ result = octeon_i2c_lost_arb(tmp, !(ctl & TWSI_CTL_AAK));
+ if (result)
+ return result;
- if ((tmp != STAT_RXDATA_ACK) && (tmp != STAT_RXADDR_ACK)) {
- dev_err(i2c->dev,
- "%s: bad status before read (0x%x)\n",
- __func__, tmp);
- return -EIO;
+ switch (tmp) {
+ case STAT_RXDATA_ACK:
+ case STAT_RXDATA_NAK:
+ data[i++] = octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_DATA);
}
- if (i + 1 < length)
- octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL,
- TWSI_CTL_ENAB | TWSI_CTL_AAK);
- else
- octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL,
- TWSI_CTL_ENAB);
+ /* NAK last recv'd byte, as a no-more-please */
+ if (last && i == length - 1)
+ ctl &= ~TWSI_CTL_AAK;
+
+ /* clr iflg to allow next event */
+ octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, ctl);
result = octeon_i2c_wait(i2c);
if (result)
return result;
-
- data[i] = octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_DATA);
if (recv_len && i == 0) {
if (data[i] > I2C_SMBUS_BLOCK_MAX + 1) {
dev_err(i2c->dev,
@@ -379,6 +846,53 @@ static int octeon_i2c_read(struct octeon_i2c *i2c, int target,
}
/**
+ * octeon_i2c_write - send data to the bus via low-level controller
+ * @i2c: The struct octeon_i2c
+ * @target: Target address
+ * @data: Pointer to the data to be sent
+ * @length: Length of the data
+ * @last: is last msg in combined operation?
+ *
+ * The address is sent over the bus, then the data.
+ *
+ * Returns 0 on success, otherwise a negative errno.
+ */
+static int octeon_i2c_write(struct octeon_i2c *i2c, int target,
+ const u8 *data, int length, int first, int last)
+{
+ int i, result;
+
+ result = octeon_i2c_start(i2c, first);
+ if (result)
+ return result;
+
+ octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_DATA, target << 1);
+ octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, TWSI_CTL_ENAB);
+
+ result = octeon_i2c_wait(i2c);
+ if (result)
+ return result;
+
+ for (i = 0; i < length; i++) {
+ result = check_arb(i2c, false);
+ if (result)
+ return result;
+
+ octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_DATA, data[i]);
+ octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, TWSI_CTL_ENAB);
+
+ result = octeon_i2c_wait(i2c);
+ if (result)
+ return result;
+ result = check_arb(i2c, false);
+ if (result)
+ return result;
+ }
+
+ return 0;
+}
+
+/**
* octeon_i2c_xfer - The driver's master_xfer function
* @adap: Pointer to the i2c_adapter structure
* @msgs: Pointer to the messages to be processed
@@ -392,8 +906,31 @@ static int octeon_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
struct octeon_i2c *i2c = i2c_get_adapdata(adap);
int i, ret = 0;
+ if (num == 1) {
+ if (msgs[0].len > 0 && msgs[0].len <= 8) {
+ if (msgs[0].flags & I2C_M_RD)
+ ret = octeon_i2c_simple_read(i2c, msgs);
+ else
+ ret = octeon_i2c_simple_write(i2c, msgs);
+ goto out;
+ }
+ } else if (num == 2) {
+ if ((msgs[0].flags & I2C_M_RD) == 0 &&
+ (msgs[1].flags & I2C_M_RECV_LEN) == 0 &&
+ msgs[0].len > 0 && msgs[0].len <= 2 &&
+ msgs[1].len > 0 && msgs[1].len <= 8 &&
+ msgs[0].addr == msgs[1].addr) {
+ if (msgs[1].flags & I2C_M_RD)
+ ret = octeon_i2c_ia_read(i2c, msgs);
+ else
+ ret = octeon_i2c_ia_write(i2c, msgs);
+ goto out;
+ }
+ }
+
for (i = 0; ret == 0 && i < num; i++) {
struct i2c_msg *pmsg = &msgs[i];
+ bool last = (i == (num - 1));
dev_dbg(i2c->dev,
"Doing %s %d byte(s) to/from 0x%02x - %d of %d messages\n",
@@ -401,13 +938,14 @@ static int octeon_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
pmsg->len, pmsg->addr, i + 1, num);
if (pmsg->flags & I2C_M_RD)
ret = octeon_i2c_read(i2c, pmsg->addr, pmsg->buf,
- &pmsg->len, pmsg->flags & I2C_M_RECV_LEN);
+ &pmsg->len, !i, last,
+ pmsg->flags & I2C_M_RECV_LEN);
else
ret = octeon_i2c_write(i2c, pmsg->addr, pmsg->buf,
- pmsg->len);
+ pmsg->len, !i, last);
}
octeon_i2c_stop(i2c);
-
+out:
return (ret != 0) ? ret : num;
}
@@ -428,69 +966,6 @@ static struct i2c_adapter octeon_i2c_ops = {
.algo = &octeon_i2c_algo,
};
-/* calculate and set clock divisors */
-static void octeon_i2c_set_clock(struct octeon_i2c *i2c)
-{
- int tclk, thp_base, inc, thp_idx, mdiv_idx, ndiv_idx, foscl, diff;
- int thp = 0x18, mdiv = 2, ndiv = 0, delta_hz = 1000000;
-
- for (ndiv_idx = 0; ndiv_idx < 8 && delta_hz != 0; ndiv_idx++) {
- /*
- * An mdiv value of less than 2 seems to not work well
- * with ds1337 RTCs, so we constrain it to larger values.
- */
- for (mdiv_idx = 15; mdiv_idx >= 2 && delta_hz != 0; mdiv_idx--) {
- /*
- * For given ndiv and mdiv values check the
- * two closest thp values.
- */
- tclk = i2c->twsi_freq * (mdiv_idx + 1) * 10;
- tclk *= (1 << ndiv_idx);
- thp_base = (i2c->sys_freq / (tclk * 2)) - 1;
-
- for (inc = 0; inc <= 1; inc++) {
- thp_idx = thp_base + inc;
- if (thp_idx < 5 || thp_idx > 0xff)
- continue;
-
- foscl = i2c->sys_freq / (2 * (thp_idx + 1));
- foscl = foscl / (1 << ndiv_idx);
- foscl = foscl / (mdiv_idx + 1) / 10;
- diff = abs(foscl - i2c->twsi_freq);
- if (diff < delta_hz) {
- delta_hz = diff;
- thp = thp_idx;
- mdiv = mdiv_idx;
- ndiv = ndiv_idx;
- }
- }
- }
- }
- octeon_i2c_write_sw(i2c, SW_TWSI_OP_TWSI_CLK, thp);
- octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CLKCTL, (mdiv << 3) | ndiv);
-}
-
-static int octeon_i2c_init_lowlevel(struct octeon_i2c *i2c)
-{
- u8 status;
- int tries;
-
- /* disable high level controller, enable bus access */
- octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_CTL, TWSI_CTL_ENAB);
-
- /* reset controller */
- octeon_i2c_write_sw(i2c, SW_TWSI_EOP_TWSI_RST, 0);
-
- for (tries = 10; tries; tries--) {
- udelay(1);
- status = octeon_i2c_read_sw(i2c, SW_TWSI_EOP_TWSI_STAT);
- if (status == STAT_IDLE)
- return 0;
- }
- dev_err(i2c->dev, "%s: TWSI_RST failed! (0x%x)\n", __func__, status);
- return -EIO;
-}
-
static int octeon_i2c_probe(struct platform_device *pdev)
{
struct device_node *node = pdev->dev.of_node;
--
1.9.1