RE: [PATCH] wlcore: spi: add wl18xx support

[Reizer, Eyal]

Ping on this patch

> -----Original Message-----
> From: Eyal Reizer [mailto:eyalreizer@xxxxxxxxx]
> Sent: Wednesday, March 30, 2016 4:07 PM
> To: kvalo@xxxxxxxxxxxxxx; linux-wireless@xxxxxxxxxxxxxxx;
> netdev@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx
> Cc: Reizer, Eyal
> Subject: [PATCH] wlcore: spi: add wl18xx support
> 
> Add support for using with both wl12xx and wl18xx.
> 
> - all wilink family needs special init command for entering wspi mode.
>   extra clock cycles should be sent after the spi init command while the
>   cs pin is high.
> - switch to controling the cs pin from the spi driver for achieveing the
>   above.
> - the selected cs gpio is read from the spi device-tree node using the
>   cs-gpios field and setup as a gpio.
> - See the example below for specifying the cs gpio using the cs-gpios entry
> 
> &spi0	{
>  	status = "okay";
> 	pinctrl-names = "default";
> 	pinctrl-0 = <&spi0_pins>;
> 	cs-gpios = <&gpio0 5 0>;
> 	#address-cells = <1>;
> 	#size-cells = <0>;
>  	wlcore: wlcore@0 {
> 		compatible = "ti,wl1835";
> 		vwlan-supply = <&wlan_en_reg>;
> 		spi-max-frequency = <48000000>;
> 		reg = <0>;      /* chip select 0 on spi0, ie spi0.0 */
> 		interrupt-parent = <&gpio0>;
> 		interrupts = <27 IRQ_TYPE_EDGE_RISING>;
>  	};
> };
> 
> Signed-off-by: Eyal Reizer <eyalr@xxxxxx>
> ---
>  drivers/net/wireless/ti/wlcore/spi.c |  176
> ++++++++++++++++++++++++++++++----
>  1 file changed, 157 insertions(+), 19 deletions(-)
> 
> diff --git a/drivers/net/wireless/ti/wlcore/spi.c
> b/drivers/net/wireless/ti/wlcore/spi.c
> index 96d9c9d..6c5a369 100644
> --- a/drivers/net/wireless/ti/wlcore/spi.c
> +++ b/drivers/net/wireless/ti/wlcore/spi.c
> @@ -32,6 +32,7 @@
>  #include <linux/platform_device.h>
>  #include <linux/of_irq.h>
>  #include <linux/regulator/consumer.h>
> +#include <linux/gpio.h>
> 
>  #include "wlcore.h"
>  #include "wl12xx_80211.h"
> @@ -70,16 +71,30 @@
>  #define WSPI_MAX_CHUNK_SIZE    4092
> 
>  /*
> - * only support SPI for 12xx - this code should be reworked when 18xx
> - * support is introduced
> + * wl18xx driver aggregation buffer size is (13 * PAGE_SIZE) compared
> + to
> + * (4 * PAGE_SIZE) for wl12xx, so use the larger buffer needed for
> + wl18xx
>   */
> -#define SPI_AGGR_BUFFER_SIZE (4 * PAGE_SIZE)
> +#define SPI_AGGR_BUFFER_SIZE (13 * PAGE_SIZE)
> 
>  /* Maximum number of SPI write chunks */  #define
> WSPI_MAX_NUM_OF_CHUNKS \
>  	((SPI_AGGR_BUFFER_SIZE / WSPI_MAX_CHUNK_SIZE) + 1)
> 
> 
> +struct wilink_familiy_data {
> +	char name[8];
> +};
> +
> +const struct wilink_familiy_data *wilink_data;
> +
> +static const struct wilink_familiy_data wl18xx_data = {
> +	.name = "wl18xx",
> +};
> +
> +static const struct wilink_familiy_data wl12xx_data = {
> +	.name = "wl12xx",
> +};
> +
>  struct wl12xx_spi_glue {
>  	struct device *dev;
>  	struct platform_device *core;
> @@ -120,6 +135,8 @@ static void wl12xx_spi_init(struct device *child)
>  	struct spi_transfer t;
>  	struct spi_message m;
>  	u8 *cmd = kzalloc(WSPI_INIT_CMD_LEN, GFP_KERNEL);
> +	struct spi_device *spi = (struct spi_device *)glue->dev;
> +	struct spi_master *master = spi->master;
> 
>  	if (!cmd) {
>  		dev_err(child->parent,
> @@ -127,6 +144,15 @@ static void wl12xx_spi_init(struct device *child)
>  		return;
>  	}
> 
> +	if (!master->cs_gpios) {
> +		dev_err(child->parent,
> +			"spi chip select pin missing in platform data!\n");
> +		return;
> +	}
> +
> +	/* Drive CS line low */
> +	gpio_direction_output(master->cs_gpios[0], 0);
> +
>  	memset(&t, 0, sizeof(t));
>  	spi_message_init(&m);
> 
> @@ -163,6 +189,26 @@ static void wl12xx_spi_init(struct device *child)
>  	spi_message_add_tail(&t, &m);
> 
>  	spi_sync(to_spi_device(glue->dev), &m);
> +
> +	/* Send extra clocks with CS high. this is required by the wilink
> +	 * family in order for successfully enter WSPI mode
> +	 */
> +	gpio_direction_output(master->cs_gpios[0], 1);
> +
> +	memset(&m, 0, sizeof(m));
> +	spi_message_init(&m);
> +
> +	cmd[0] = 0xff;
> +	cmd[1] = 0xff;
> +	cmd[2] = 0xff;
> +	cmd[3] = 0xff;
> +	swab32s((u32 *)cmd);
> +
> +	t.tx_buf = cmd;
> +	t.len = 4;
> +	spi_message_add_tail(&t, &m);
> +	spi_sync(to_spi_device(glue->dev), &m);
> +
>  	kfree(cmd);
>  }
> 
> @@ -213,6 +259,16 @@ static int __must_check
> wl12xx_spi_raw_read(struct device *child, int addr,
>  	u32 *busy_buf;
>  	u32 *cmd;
>  	u32 chunk_len;
> +	struct spi_device *spi = (struct spi_device *)glue->dev;
> +	struct spi_master *master = spi->master;
> +
> +	if (!master->cs_gpios) {
> +		dev_err(child->parent,
> +			"spi chip select pin missing in platform data!\n");
> +		return -EINVAL;
> +	}
> +	/* Drive CS line low */
> +	gpio_direction_output(master->cs_gpios[0], 0);
> 
>  	while (len > 0) {
>  		chunk_len = min_t(size_t, WSPI_MAX_CHUNK_SIZE, len); @@
> -267,25 +323,44 @@ static int __must_check wl12xx_spi_raw_read(struct
> device *child, int addr,
>  		len -= chunk_len;
>  	}
> 
> +	/* Drive CS line high */
> +	gpio_direction_output(master->cs_gpios[0], 1);
>  	return 0;
>  }
> 
> -static int __must_check wl12xx_spi_raw_write(struct device *child, int addr,
> -					     void *buf, size_t len, bool fixed)
> +static int __wl12xx_spi_raw_write(struct device *child, int addr,
> +				  void *buf, size_t len, bool fixed)
>  {
>  	struct wl12xx_spi_glue *glue = dev_get_drvdata(child->parent);
> -	/* SPI write buffers - 2 for each chunk */
> -	struct spi_transfer t[2 * WSPI_MAX_NUM_OF_CHUNKS];
> +	struct spi_transfer *t;
>  	struct spi_message m;
>  	u32 commands[WSPI_MAX_NUM_OF_CHUNKS]; /* 1 command per
> chunk */
>  	u32 *cmd;
>  	u32 chunk_len;
>  	int i;
> +	struct spi_device *spi = (struct spi_device *)glue->dev;
> +	struct spi_master *master = spi->master;
> +
> +	if (!master->cs_gpios) {
> +		dev_err(child->parent,
> +			"spi chip select pin missing in platform data!\n");
> +		return -EINVAL;
> +	}
> +
> +	/* SPI write buffers - 2 for each chunk */
> +	t = kzalloc(sizeof(*t) * 2 * WSPI_MAX_NUM_OF_CHUNKS,
> GFP_KERNEL);
> +	if (!t) {
> +		dev_err(child->parent,
> +			"could not allocate spi write buffer\n");
> +		return -ENOMEM;
> +	}
> +
> +	/* Drive CS line low */
> +	gpio_direction_output(master->cs_gpios[0], 0);
> 
>  	WARN_ON(len > SPI_AGGR_BUFFER_SIZE);
> 
>  	spi_message_init(&m);
> -	memset(t, 0, sizeof(t));
> 
>  	cmd = &commands[0];
>  	i = 0;
> @@ -318,9 +393,29 @@ static int __must_check
> wl12xx_spi_raw_write(struct device *child, int addr,
> 
>  	spi_sync(to_spi_device(glue->dev), &m);
> 
> +	/* Drive CS line high */
> +	gpio_direction_output(master->cs_gpios[0], 1);
> +
> +	kfree(t);
>  	return 0;
>  }
> 
> +static int __must_check wl12xx_spi_raw_write(struct device *child, int addr,
> +					     void *buf, size_t len, bool fixed) {
> +	int ret;
> +
> +	/* The ELP wakeup write may fail the first time due to internal
> +	 * hardware latency. It is safer to send the wakeup command twice to
> +	 * avoid unexpected failures.
> +	 */
> +	if (addr == HW_ACCESS_ELP_CTRL_REG)
> +		ret = __wl12xx_spi_raw_write(child, addr, buf, len, fixed);
> +	ret = __wl12xx_spi_raw_write(child, addr, buf, len, fixed);
> +
> +	return ret;
> +}
> +
>  /**
>   * wl12xx_spi_set_power - power on/off the wl12xx unit
>   * @child: wl12xx device handle.
> @@ -349,17 +444,38 @@ static int wl12xx_spi_set_power(struct device
> *child, bool enable)
>  	return ret;
>  }
> 
> +/**
> + * wl12xx_spi_set_block_size
> + *
> + * This function is not needed for spi mode, but need to be present.
> + * Without it defined the wlcore fallback to use the wrong packet
> + * allignment on tx.
> + */
> +static void wl12xx_spi_set_block_size(struct device *child,
> +				      unsigned int blksz)
> +{
> +}
> +
>  static struct wl1271_if_operations spi_ops = {
>  	.read		= wl12xx_spi_raw_read,
>  	.write		= wl12xx_spi_raw_write,
>  	.reset		= wl12xx_spi_reset,
>  	.init		= wl12xx_spi_init,
>  	.power		= wl12xx_spi_set_power,
> -	.set_block_size = NULL,
> +	.set_block_size = wl12xx_spi_set_block_size,
>  };
> 
>  static const struct of_device_id wlcore_spi_of_match_table[] = {
> -	{ .compatible = "ti,wl1271" },
> +	{ .compatible = "ti,wl1271", .data = &wl12xx_data},
> +	{ .compatible = "ti,wl1273", .data = &wl12xx_data},
> +	{ .compatible = "ti,wl1281", .data = &wl12xx_data},
> +	{ .compatible = "ti,wl1283", .data = &wl12xx_data},
> +	{ .compatible = "ti,wl1801", .data = &wl18xx_data},
> +	{ .compatible = "ti,wl1805", .data = &wl18xx_data},
> +	{ .compatible = "ti,wl1807", .data = &wl18xx_data},
> +	{ .compatible = "ti,wl1831", .data = &wl18xx_data},
> +	{ .compatible = "ti,wl1835", .data = &wl18xx_data},
> +	{ .compatible = "ti,wl1837", .data = &wl18xx_data},
>  	{ }
>  };
>  MODULE_DEVICE_TABLE(of, wlcore_spi_of_match_table); @@ -375,18
> +491,24 @@ static int wlcore_probe_of(struct spi_device *spi, struct
> wl12xx_spi_glue *glue,
>  			   struct wlcore_platdev_data *pdev_data)  {
>  	struct device_node *dt_node = spi->dev.of_node;
> -	int ret;
> +	const struct of_device_id *of_id;
> +
> +	of_id = of_match_node(wlcore_spi_of_match_table, dt_node);
> +	if (!of_id)
> +		return -ENODEV;
> +
> +	wilink_data = of_id->data;
> +	dev_info(&spi->dev, "selected chip familiy is %s\n",
> +		 wilink_data->name);
> 
>  	if (of_find_property(dt_node, "clock-xtal", NULL))
>  		pdev_data->ref_clock_xtal = true;
> 
> -	ret = of_property_read_u32(dt_node, "ref-clock-frequency",
> -				   &pdev_data->ref_clock_freq);
> -	if (IS_ERR_VALUE(ret)) {
> -		dev_err(glue->dev,
> -			"can't get reference clock frequency (%d)\n", ret);
> -		return ret;
> -	}
> +	/* optional clock frequency params */
> +	of_property_read_u32(dt_node, "ref-clock-frequency",
> +			     &pdev_data->ref_clock_freq);
> +	of_property_read_u32(dt_node, "tcxo-clock-frequency",
> +			     &pdev_data->tcxo_clock_freq);
> 
>  	return 0;
>  }
> @@ -397,6 +519,7 @@ static int wl1271_probe(struct spi_device *spi)
>  	struct wlcore_platdev_data pdev_data;
>  	struct resource res[1];
>  	int ret;
> +	struct spi_master *master = spi->master;
> 
>  	memset(&pdev_data, 0x00, sizeof(pdev_data));
> 
> @@ -410,6 +533,12 @@ static int wl1271_probe(struct spi_device *spi)
> 
>  	glue->dev = &spi->dev;
> 
> +	if (!master->cs_gpios) {
> +		dev_err(glue->dev,
> +			"spi chip select pin missing in platform data!\n");
> +		return -EINVAL;
> +	}
> +
>  	spi_set_drvdata(spi, glue);
> 
>  	/* This is the only SPI value that we need to set here, the rest @@ -
> 431,15 +560,21 @@ static int wl1271_probe(struct spi_device *spi)
>  		return ret;
>  	}
> 
> +	if (gpio_request(master->cs_gpios[0], "spi1-cs0"))
> +		return -EINVAL;
> +
>  	ret = spi_setup(spi);
>  	if (ret < 0) {
>  		dev_err(glue->dev, "spi_setup failed\n");
> +		gpio_free(master->cs_gpios[0]);
>  		return ret;
>  	}
> 
> -	glue->core = platform_device_alloc("wl12xx",
> PLATFORM_DEVID_AUTO);
> +	glue->core = platform_device_alloc(wilink_data->name,
> +					   PLATFORM_DEVID_AUTO);
>  	if (!glue->core) {
>  		dev_err(glue->dev, "can't allocate platform_device\n");
> +		gpio_free(master->cs_gpios[0]);
>  		return -ENOMEM;
>  	}
> 
> @@ -474,14 +609,17 @@ static int wl1271_probe(struct spi_device *spi)
> 
>  out_dev_put:
>  	platform_device_put(glue->core);
> +	gpio_free(master->cs_gpios[0]);
>  	return ret;
>  }
> 
>  static int wl1271_remove(struct spi_device *spi)  {
>  	struct wl12xx_spi_glue *glue = spi_get_drvdata(spi);
> +	struct spi_master *master = spi->master;
> 
>  	platform_device_unregister(glue->core);
> +	gpio_free(master->cs_gpios[0]);
> 
>  	return 0;
>  }
> --
> 1.7.9.5