Re: [RESEND PATCH v7 4/6] mfd: cros_ec: Add more definitions for PD commands
From: Lee Jones
Date: Mon Apr 11 2016 - 07:27:23 EST
On Tue, 05 Apr 2016, Tomeu Vizoso wrote:
> Copy a few structs and commands from the EC firmware headers so we can
> communicate with the EC regarding PD functionality.
>
> Signed-off-by: Tomeu Vizoso <tomeu.vizoso@xxxxxxxxxxxxx>
> ---
>
> Changes in v7: None
> Changes in v6: None
> Changes in v5: None
> Changes in v4: None
> Changes in v3: None
> Changes in v2: None
>
> include/linux/mfd/cros_ec_commands.h | 324 ++++++++++++++++++++++++++++++++++-
> 1 file changed, 319 insertions(+), 5 deletions(-)
>
> diff --git a/include/linux/mfd/cros_ec_commands.h b/include/linux/mfd/cros_ec_commands.h
> index d86526f0bd8e..4f056d2747ff 100644
> --- a/include/linux/mfd/cros_ec_commands.h
> +++ b/include/linux/mfd/cros_ec_commands.h
> @@ -286,6 +286,9 @@ enum host_event_code {
> /* Hang detect logic detected a hang and warm rebooted the AP */
> EC_HOST_EVENT_HANG_REBOOT = 21,
>
> + /* PD MCU triggering host event */
> + EC_HOST_EVENT_PD_MCU = 22,
> +
> /*
> * The high bit of the event mask is not used as a host event code. If
> * it reads back as set, then the entire event mask should be
> @@ -2273,6 +2276,13 @@ struct ec_params_ext_power_current_limit {
> uint32_t limit; /* in mA */
> } __packed;
>
> +struct ec_params_external_power_limit_v1 {
> + uint16_t current_lim; /* in mA, or EC_POWER_LIMIT_NONE to clear limit */
> + uint16_t voltage_lim; /* in mV, or EC_POWER_LIMIT_NONE to clear limit */
Better if you rename to *_mA and *_mV respectively.
> +} __packed;
> +
> +#define EC_POWER_LIMIT_NONE 0xffff
> +
> /*****************************************************************************/
> /* Smart battery pass-through */
>
> @@ -2527,8 +2537,6 @@ struct ec_params_reboot_ec {
> */
> #define EC_CMD_VERSION0 0xdc
>
> -#endif /* !__ACPI__ */
> -
What's this? This looks like a bug. If it is, it needs to be in
another patch.
> /*****************************************************************************/
> /*
> * PD commands
> @@ -2538,16 +2546,51 @@ struct ec_params_reboot_ec {
>
> /* EC to PD MCU exchange status command */
> #define EC_CMD_PD_EXCHANGE_STATUS 0x100
> +#define EC_VER_PD_EXCHANGE_STATUS 2
> +
> +enum pd_charge_state {
> + PD_CHARGE_NO_CHANGE = 0, /* Don't change charge state */
> + PD_CHARGE_NONE, /* No charging allowed */
> + PD_CHARGE_5V, /* 5V charging only */
> + PD_CHARGE_MAX /* Charge at max voltage */
> +};
>
> /* Status of EC being sent to PD */
> +#define EC_STATUS_HIBERNATING (1 << 0)
> +
> struct ec_params_pd_status {
> - int8_t batt_soc; /* battery state of charge */
> + uint8_t status; /* EC status */
> + int8_t batt_soc; /* battery state of charge */
> + uint8_t charge_state; /* charging state (from enum pd_charge_state) */
All these comments look messy. Please use kerneldoc format instead.
> } __packed;
>
> /* Status of PD being sent back to EC */
> +#define PD_STATUS_HOST_EVENT (1 << 0) /* Forward host event to AP */
> +#define PD_STATUS_IN_RW (1 << 1) /* Running RW image */
> +#define PD_STATUS_JUMPED_TO_IMAGE (1 << 2) /* Current image was jumped to */
> +#define PD_STATUS_TCPC_ALERT_0 (1 << 3) /* Alert active in port 0 TCPC */
> +#define PD_STATUS_TCPC_ALERT_1 (1 << 4) /* Alert active in port 1 TCPC */
> +#define PD_STATUS_TCPC_ALERT_2 (1 << 5) /* Alert active in port 2 TCPC */
> +#define PD_STATUS_TCPC_ALERT_3 (1 << 6) /* Alert active in port 3 TCPC */
BIT()
> +#define PD_STATUS_EC_INT_ACTIVE (PD_STATUS_TCPC_ALERT_0 | \
> + PD_STATUS_TCPC_ALERT_1 | \
> + PD_STATUS_HOST_EVENT)
> struct ec_response_pd_status {
> - int8_t status; /* PD MCU status */
> - uint32_t curr_lim_ma; /* input current limit */
> + uint32_t curr_lim_ma; /* input current limit */
> + uint16_t status; /* PD MCU status */
> + int8_t active_charge_port; /* active charging port */
> +} __packed;
Kerneldoc
> +/* AP to PD MCU host event status command, cleared on read */
> +#define EC_CMD_PD_HOST_EVENT_STATUS 0x104
> +
> +/* PD MCU host event status bits */
> +#define PD_EVENT_UPDATE_DEVICE (1 << 0)
> +#define PD_EVENT_POWER_CHANGE (1 << 1)
> +#define PD_EVENT_IDENTITY_RECEIVED (1 << 2)
> +#define PD_EVENT_DATA_SWAP (1 << 3)
BIT()
> +struct ec_response_host_event_status {
> + uint32_t status; /* PD MCU host event status */
> } __packed;
>
> /* Set USB type-C port role and muxes */
> @@ -2559,6 +2602,7 @@ enum usb_pd_control_role {
> USB_PD_CTRL_ROLE_TOGGLE_OFF = 2,
> USB_PD_CTRL_ROLE_FORCE_SINK = 3,
> USB_PD_CTRL_ROLE_FORCE_SOURCE = 4,
> + USB_PD_CTRL_ROLE_COUNT
> };
>
> enum usb_pd_control_mux {
> @@ -2568,14 +2612,284 @@ enum usb_pd_control_mux {
> USB_PD_CTRL_MUX_DP = 3,
> USB_PD_CTRL_MUX_DOCK = 4,
> USB_PD_CTRL_MUX_AUTO = 5,
> + USB_PD_CTRL_MUX_COUNT
> +};
> +
> +enum usb_pd_control_swap {
> + USB_PD_CTRL_SWAP_NONE = 0,
> + USB_PD_CTRL_SWAP_DATA = 1,
> + USB_PD_CTRL_SWAP_POWER = 2,
> + USB_PD_CTRL_SWAP_VCONN = 3,
> + USB_PD_CTRL_SWAP_COUNT
You don't need to number these. The enum C standard will enforce the
numbering strategy for you.
> };
>
> struct ec_params_usb_pd_control {
> uint8_t port;
> uint8_t role;
> uint8_t mux;
> + uint8_t swap;
> +} __packed;
> +
> +#define PD_CTRL_RESP_ENABLED_COMMS (1 << 0) /* Communication enabled */
> +#define PD_CTRL_RESP_ENABLED_CONNECTED (1 << 1) /* Device connected */
> +#define PD_CTRL_RESP_ENABLED_PD_CAPABLE (1 << 2) /* Partner is PD capable */
> +
> +#define PD_CTRL_RESP_ROLE_POWER (1 << 0) /* 0=SNK/1=SRC */
> +#define PD_CTRL_RESP_ROLE_DATA (1 << 1) /* 0=UFP/1=DFP */
> +#define PD_CTRL_RESP_ROLE_VCONN (1 << 2) /* Vconn status */
> +#define PD_CTRL_RESP_ROLE_DR_POWER (1 << 3) /* Partner is dualrole power */
> +#define PD_CTRL_RESP_ROLE_DR_DATA (1 << 4) /* Partner is dualrole data */
> +#define PD_CTRL_RESP_ROLE_USB_COMM (1 << 5) /* Partner USB comm capable */
> +#define PD_CTRL_RESP_ROLE_EXT_POWERED (1 << 6) /* Partner externally powerd */
BIT()
> +struct ec_response_usb_pd_control {
> + uint8_t enabled;
> + uint8_t role;
> + uint8_t polarity;
> + uint8_t state;
> +} __packed;
> +
> +struct ec_response_usb_pd_control_v1 {
> + uint8_t enabled;
> + uint8_t role;
> + uint8_t polarity;
> + char state[32];
> +} __packed;
> +
> +#define EC_CMD_USB_PD_PORTS 0x102
> +
> +struct ec_response_usb_pd_ports {
> + uint8_t num_ports;
> +} __packed;
> +
> +#define EC_CMD_USB_PD_POWER_INFO 0x103
> +
> +#define PD_POWER_CHARGING_PORT 0xff
> +struct ec_params_usb_pd_power_info {
> + uint8_t port;
> +} __packed;
> +
> +enum usb_chg_type {
> + USB_CHG_TYPE_NONE,
> + USB_CHG_TYPE_PD,
> + USB_CHG_TYPE_C,
> + USB_CHG_TYPE_PROPRIETARY,
> + USB_CHG_TYPE_BC12_DCP,
> + USB_CHG_TYPE_BC12_CDP,
> + USB_CHG_TYPE_BC12_SDP,
> + USB_CHG_TYPE_OTHER,
> + USB_CHG_TYPE_VBUS,
> + USB_CHG_TYPE_UNKNOWN,
> +};
> +enum usb_power_roles {
> + USB_PD_PORT_POWER_DISCONNECTED,
> + USB_PD_PORT_POWER_SOURCE,
> + USB_PD_PORT_POWER_SINK,
> + USB_PD_PORT_POWER_SINK_NOT_CHARGING,
> +};
> +
> +struct usb_chg_measures {
> + uint16_t voltage_max;
> + uint16_t voltage_now;
> + uint16_t current_max;
> + uint16_t current_lim;
> +} __packed;
> +
> +struct ec_response_usb_pd_power_info {
> + uint8_t role;
> + uint8_t type;
> + uint8_t dualrole;
> + uint8_t reserved1;
> + struct usb_chg_measures meas;
> + uint32_t max_power;
> +} __packed;
> +
> +/* Write USB-PD device FW */
> +#define EC_CMD_USB_PD_FW_UPDATE 0x110
> +
> +enum usb_pd_fw_update_cmds {
> + USB_PD_FW_REBOOT,
> + USB_PD_FW_FLASH_ERASE,
> + USB_PD_FW_FLASH_WRITE,
> + USB_PD_FW_ERASE_SIG,
> +};
> +
> +struct ec_params_usb_pd_fw_update {
> + uint16_t dev_id;
> + uint8_t cmd;
> + uint8_t port;
> + uint32_t size; /* Size to write in bytes */
> + /* Followed by data to write */
> +} __packed;
> +
> +/* Write USB-PD Accessory RW_HASH table entry */
> +#define EC_CMD_USB_PD_RW_HASH_ENTRY 0x111
> +/* RW hash is first 20 bytes of SHA-256 of RW section */
> +#define PD_RW_HASH_SIZE 20
> +struct ec_params_usb_pd_rw_hash_entry {
> + uint16_t dev_id;
> + uint8_t dev_rw_hash[PD_RW_HASH_SIZE];
> + uint8_t reserved; /* For alignment of current_image */
> + uint32_t current_image; /* One of ec_current_image */
> +} __packed;
> +
> +/* Read USB-PD Accessory info */
> +#define EC_CMD_USB_PD_DEV_INFO 0x112
> +
> +struct ec_params_usb_pd_info_request {
> + uint8_t port;
> +} __packed;
> +
> +/* Read USB-PD Device discovery info */
> +#define EC_CMD_USB_PD_DISCOVERY 0x113
> +struct ec_params_usb_pd_discovery_entry {
> + uint16_t vid; /* USB-IF VID */
> + uint16_t pid; /* USB-IF PID */
> + uint8_t ptype; /* product type (hub,periph,cable,ama) */
> +} __packed;
> +
> +/* Override default charge behavior */
> +#define EC_CMD_PD_CHARGE_PORT_OVERRIDE 0x114
> +
> +/* Negative port parameters have special meaning */
> +enum usb_pd_override_ports {
> + OVERRIDE_DONT_CHARGE = -2,
> + OVERRIDE_OFF = -1,
> + /* [0, CONFIG_USB_PD_PORT_COUNT): Port# */
> +};
> +
> +struct ec_params_charge_port_override {
> + int16_t override_port; /* Override port# */
> +} __packed;
> +
> +/* Read (and delete) one entry of PD event log */
> +#define EC_CMD_PD_GET_LOG_ENTRY 0x115
> +
> +struct ec_response_pd_log {
> + uint32_t timestamp; /* relative timestamp in milliseconds */
> + uint8_t type; /* event type : see PD_EVENT_xx below */
> + uint8_t size_port; /* [7:5] port number [4:0] payload size in bytes */
> + uint16_t data; /* type-defined data payload */
> + uint8_t payload[0]; /* optional additional data payload: 0..16 bytes */
> +} __packed;
> +
> +
> +/* The timestamp is the microsecond counter shifted to get about a ms. */
> +#define PD_LOG_TIMESTAMP_SHIFT 10 /* 1 LSB = 1024us */
> +
> +#define PD_LOG_SIZE_MASK 0x1f
> +#define PD_LOG_PORT_MASK 0xe0
> +#define PD_LOG_PORT_SHIFT 5
> +#define PD_LOG_PORT_SIZE(port, size) (((port) << PD_LOG_PORT_SHIFT) | \
> + ((size) & PD_LOG_SIZE_MASK))
> +#define PD_LOG_PORT(size_port) ((size_port) >> PD_LOG_PORT_SHIFT)
> +#define PD_LOG_SIZE(size_port) ((size_port) & PD_LOG_SIZE_MASK)
> +
> +/* PD event log : entry types */
> +/* PD MCU events */
> +#define PD_EVENT_MCU_BASE 0x00
> +#define PD_EVENT_MCU_CHARGE (PD_EVENT_MCU_BASE+0)
> +#define PD_EVENT_MCU_CONNECT (PD_EVENT_MCU_BASE+1)
> +/* Reserved for custom board event */
> +#define PD_EVENT_MCU_BOARD_CUSTOM (PD_EVENT_MCU_BASE+2)
> +/* PD generic accessory events */
> +#define PD_EVENT_ACC_BASE 0x20
> +#define PD_EVENT_ACC_RW_FAIL (PD_EVENT_ACC_BASE+0)
> +#define PD_EVENT_ACC_RW_ERASE (PD_EVENT_ACC_BASE+1)
> +/* PD power supply events */
> +#define PD_EVENT_PS_BASE 0x40
> +#define PD_EVENT_PS_FAULT (PD_EVENT_PS_BASE+0)
> +/* PD video dongles events */
> +#define PD_EVENT_VIDEO_BASE 0x60
> +#define PD_EVENT_VIDEO_DP_MODE (PD_EVENT_VIDEO_BASE+0)
> +#define PD_EVENT_VIDEO_CODEC (PD_EVENT_VIDEO_BASE+1)
> +/* Returned in the "type" field, when there is no entry available */
> +#define PD_EVENT_NO_ENTRY 0xff
> +
> +/*
> + * PD_EVENT_MCU_CHARGE event definition :
> + * the payload is "struct usb_chg_measures"
> + * the data field contains the port state flags as defined below :
> + */
> +/* Port partner is a dual role device */
> +#define CHARGE_FLAGS_DUAL_ROLE (1 << 15)
> +/* Port is the pending override port */
> +#define CHARGE_FLAGS_DELAYED_OVERRIDE (1 << 14)
> +/* Port is the override port */
> +#define CHARGE_FLAGS_OVERRIDE (1 << 13)
> +/* Charger type */
> +#define CHARGE_FLAGS_TYPE_SHIFT 3
> +#define CHARGE_FLAGS_TYPE_MASK (0xf << CHARGE_FLAGS_TYPE_SHIFT)
> +/* Power delivery role */
> +#define CHARGE_FLAGS_ROLE_MASK (7 << 0)
> +
> +/*
> + * PD_EVENT_PS_FAULT data field flags definition :
> + */
> +#define PS_FAULT_OCP 1
> +#define PS_FAULT_FAST_OCP 2
> +#define PS_FAULT_OVP 3
> +#define PS_FAULT_DISCH 4
> +
> +/*
> + * PD_EVENT_VIDEO_CODEC payload is "struct mcdp_info".
> + */
> +struct mcdp_version {
> + uint8_t major;
> + uint8_t minor;
> + uint16_t build;
> } __packed;
>
> +struct mcdp_info {
> + uint8_t family[2];
> + uint8_t chipid[2];
> + struct mcdp_version irom;
> + struct mcdp_version fw;
> +} __packed;
> +
> +/* struct mcdp_info field decoding */
> +#define MCDP_CHIPID(chipid) ((chipid[0] << 8) | chipid[1])
> +#define MCDP_FAMILY(family) ((family[0] << 8) | family[1])
> +
> +/* Get/Set USB-PD Alternate mode info */
> +#define EC_CMD_USB_PD_GET_AMODE 0x116
> +struct ec_params_usb_pd_get_mode_request {
> + uint16_t svid_idx; /* SVID index to get */
> + uint8_t port; /* port */
> +} __packed;
> +
> +struct ec_params_usb_pd_get_mode_response {
> + uint16_t svid; /* SVID */
> + uint16_t opos; /* Object Position */
> + uint32_t vdo[6]; /* Mode VDOs */
> +} __packed;
> +
> +#define EC_CMD_USB_PD_SET_AMODE 0x117
> +
> +enum pd_mode_cmd {
> + PD_EXIT_MODE = 0,
> + PD_ENTER_MODE = 1,
> + /* Not a command. Do NOT remove. */
> + PD_MODE_CMD_COUNT,
> +};
> +
> +struct ec_params_usb_pd_set_mode_request {
> + uint32_t cmd; /* enum pd_mode_cmd */
> + uint16_t svid; /* SVID to set */
> + uint8_t opos; /* Object Position */
> + uint8_t port; /* port */
> +} __packed;
> +
> +/* Ask the PD MCU to record a log of a requested type */
> +#define EC_CMD_PD_WRITE_LOG_ENTRY 0x118
> +
> +struct ec_params_pd_write_log_entry {
> + uint8_t type; /* event type : see PD_EVENT_xx above */
> + uint8_t port; /* port#, or 0 for events unrelated to a given port */
> +} __packed;
> +
> +#endif /* !__ACPI__ */
> +
> /*****************************************************************************/
> /*
> * Passthru commands
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org â Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog