[PATCH] mfd: Use IS_ENABLED(CONFIG_FOO) instead of checking FOO || FOO_MODULE

[Javier Martinez Canillas]

The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.

Signed-off-by: Javier Martinez Canillas <javier@xxxxxxxxxxxxxxx>

---

 drivers/mfd/dm355evm_msp.c | 8 ++++----
 drivers/mfd/wm8400-core.c  | 6 +++---
 2 files changed, 7 insertions(+), 7 deletions(-)

diff --git a/drivers/mfd/dm355evm_msp.c b/drivers/mfd/dm355evm_msp.c
index ec4438ed2faf..04c25c4a8ff4 100644
--- a/drivers/mfd/dm355evm_msp.c
+++ b/drivers/mfd/dm355evm_msp.c
@@ -33,25 +33,25 @@
  * This driver was tested with firmware revision A4.
  */
 
-#if defined(CONFIG_INPUT_DM355EVM) || defined(CONFIG_INPUT_DM355EVM_MODULE)
+#if IS_ENABLED(CONFIG_INPUT_DM355EVM)
 #define msp_has_keyboard()	true
 #else
 #define msp_has_keyboard()	false
 #endif
 
-#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
+#if IS_ENABLED(CONFIG_LEDS_GPIO)
 #define msp_has_leds()		true
 #else
 #define msp_has_leds()		false
 #endif
 
-#if defined(CONFIG_RTC_DRV_DM355EVM) || defined(CONFIG_RTC_DRV_DM355EVM_MODULE)
+#if IS_ENABLED(CONFIG_RTC_DRV_DM355EVM)
 #define msp_has_rtc()		true
 #else
 #define msp_has_rtc()		false
 #endif
 
-#if defined(CONFIG_VIDEO_TVP514X) || defined(CONFIG_VIDEO_TVP514X_MODULE)
+#if IS_ENABLED(CONFIG_VIDEO_TVP514X)
 #define msp_has_tvp()		true
 #else
 #define msp_has_tvp()		false
diff --git a/drivers/mfd/wm8400-core.c b/drivers/mfd/wm8400-core.c
index 3bd44a45c378..8f9cbc0fb37a 100644
--- a/drivers/mfd/wm8400-core.c
+++ b/drivers/mfd/wm8400-core.c
@@ -156,7 +156,7 @@ void wm8400_reset_codec_reg_cache(struct wm8400 *wm8400)
 }
 EXPORT_SYMBOL_GPL(wm8400_reset_codec_reg_cache);
 
-#if defined(CONFIG_I2C) || defined(CONFIG_I2C_MODULE)
+#if IS_ENABLED(CONFIG_I2C)
 static int wm8400_i2c_probe(struct i2c_client *i2c,
 			    const struct i2c_device_id *id)
 {
@@ -205,7 +205,7 @@ static int __init wm8400_module_init(void)
 {
 	int ret = -ENODEV;
 
-#if defined(CONFIG_I2C) || defined(CONFIG_I2C_MODULE)
+#if IS_ENABLED(CONFIG_I2C)
 	ret = i2c_add_driver(&wm8400_i2c_driver);
 	if (ret != 0)
 		pr_err("Failed to register I2C driver: %d\n", ret);
@@ -217,7 +217,7 @@ subsys_initcall(wm8400_module_init);
 
 static void __exit wm8400_module_exit(void)
 {
-#if defined(CONFIG_I2C) || defined(CONFIG_I2C_MODULE)
+#if IS_ENABLED(CONFIG_I2C)
 	i2c_del_driver(&wm8400_i2c_driver);
 #endif
 }
-- 
2.5.5