Re: [PATCH v2] mmc: sdhci-of-at91: add presets setup

From: Adrian Hunter
Date: Thu Apr 28 2016 - 09:23:58 EST


On 28/04/16 15:59, Ludovic Desroches wrote:
> The controller claims to support SDR104. In fact, it only supports a
> degraded SDR104 since the maximum frequency of the SD clock is 120 MHz
> instead of 208 MHz.
> The sdhci core is unaware of it and will compute a wrong clock divider.
> We can deal with this specific case by using presets.
>
> Signed-off-by: Ludovic Desroches <ludovic.desroches@xxxxxxxxx>

Acked-by: Adrian Hunter <adrian.hunter@xxxxxxxxx>

> ---
>
> Changes:
> - v2:
> - use a define for preset_common since it's a constant
>
> drivers/mmc/host/sdhci-of-at91.c | 26 ++++++++++++++++++++++++++
> 1 file changed, 26 insertions(+)
>
> diff --git a/drivers/mmc/host/sdhci-of-at91.c b/drivers/mmc/host/sdhci-of-at91.c
> index c1923c0..25f779e 100644
> --- a/drivers/mmc/host/sdhci-of-at91.c
> +++ b/drivers/mmc/host/sdhci-of-at91.c
> @@ -18,6 +18,7 @@
> #include <linux/delay.h>
> #include <linux/err.h>
> #include <linux/io.h>
> +#include <linux/kernel.h>
> #include <linux/mmc/host.h>
> #include <linux/mmc/slot-gpio.h>
> #include <linux/module.h>
> @@ -32,6 +33,8 @@
> #define SDMMC_CACR_CAPWREN BIT(0)
> #define SDMMC_CACR_KEY (0x46 << 8)
>
> +#define SDHCI_AT91_PRESET_COMMON_CONF 0x400 /* drv type B, programmable clock mode */
> +
> struct sdhci_at91_priv {
> struct clk *hclock;
> struct clk *gck;
> @@ -163,6 +166,7 @@ static int sdhci_at91_probe(struct platform_device *pdev)
> unsigned int clk_base, clk_mul;
> unsigned int gck_rate, real_gck_rate;
> int ret;
> + unsigned int preset_div;
>
> match = of_match_device(sdhci_at91_dt_match, &pdev->dev);
> if (!match)
> @@ -230,6 +234,28 @@ static int sdhci_at91_probe(struct platform_device *pdev)
> clk_mul, real_gck_rate);
> }
>
> + /*
> + * We have to set preset values because it depends on the clk_mul
> + * value. Moreover, SDR104 is supported in a degraded mode since the
> + * maximum sd clock value is 120 MHz instead of 208 MHz. For that
> + * reason, we need to use presets to support SDR104.
> + */
> + preset_div = DIV_ROUND_UP(real_gck_rate, 24000000) - 1;
> + writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
> + host->ioaddr + SDHCI_PRESET_FOR_SDR12);
> + preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
> + writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
> + host->ioaddr + SDHCI_PRESET_FOR_SDR25);
> + preset_div = DIV_ROUND_UP(real_gck_rate, 100000000) - 1;
> + writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
> + host->ioaddr + SDHCI_PRESET_FOR_SDR50);
> + preset_div = DIV_ROUND_UP(real_gck_rate, 120000000) - 1;
> + writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
> + host->ioaddr + SDHCI_PRESET_FOR_SDR104);
> + preset_div = DIV_ROUND_UP(real_gck_rate, 50000000) - 1;
> + writew(SDHCI_AT91_PRESET_COMMON_CONF | preset_div,
> + host->ioaddr + SDHCI_PRESET_FOR_DDR50);
> +
> clk_prepare_enable(priv->mainck);
> clk_prepare_enable(priv->gck);
>
>