[PATCH 03/36] usb: serial: ti_usb_3410_5052: Remove ti_usb_3410_5052.h

From: Mathieu OTHACEHE
Date: Thu May 12 2016 - 05:07:22 EST

The definitions in ti_usb_3410_5052.h are only used in
ti_usb_3410_5052.c.
The content of the header is copied in ti_usb_3410_5052.c.

Also correct a typo in macro TI_PIPE_MODE_CONTINOUS.

Signed-off-by: Mathieu OTHACEHE <m.othacehe@xxxxxxxxx>
---
drivers/usb/serial/ti_usb_3410_5052.c | 237 +++++++++++++++++++++++++++++++++-
1 file changed, 235 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/serial/ti_usb_3410_5052.c b/drivers/usb/serial/ti_usb_3410_5052.c
index 903b45c..6002e8b 100644
--- a/drivers/usb/serial/ti_usb_3410_5052.c
+++ b/drivers/usb/serial/ti_usb_3410_5052.c
@@ -34,7 +34,240 @@
#include <linux/usb.h>
#include <linux/usb/serial.h>

-#include "ti_usb_3410_5052.h"
+/* Configuration ids */
+#define TI_BOOT_CONFIG 1
+#define TI_ACTIVE_CONFIG 2
+
+/* Vendor and product ids */
+#define TI_VENDOR_ID 0x0451
+#define IBM_VENDOR_ID 0x04b3
+#define TI_3410_PRODUCT_ID 0x3410
+#define IBM_4543_PRODUCT_ID 0x4543
+#define IBM_454B_PRODUCT_ID 0x454b
+#define IBM_454C_PRODUCT_ID 0x454c
+#define TI_3410_EZ430_ID 0xF430 /* TI ez430 development tool */
+#define TI_5052_BOOT_PRODUCT_ID 0x5052 /* no EEPROM, no firmware */
+#define TI_5152_BOOT_PRODUCT_ID 0x5152 /* no EEPROM, no firmware */
+#define TI_5052_EEPROM_PRODUCT_ID 0x505A /* EEPROM, no firmware */
+#define TI_5052_FIRMWARE_PRODUCT_ID 0x505F /* firmware is running */
+#define FRI2_PRODUCT_ID 0x5053 /* Fish River Island II */
+
+/* Multi-Tech vendor and product ids */
+#define MTS_VENDOR_ID 0x06E0
+#define MTS_GSM_NO_FW_PRODUCT_ID 0xF108
+#define MTS_CDMA_NO_FW_PRODUCT_ID 0xF109
+#define MTS_CDMA_PRODUCT_ID 0xF110
+#define MTS_GSM_PRODUCT_ID 0xF111
+#define MTS_EDGE_PRODUCT_ID 0xF112
+#define MTS_MT9234MU_PRODUCT_ID 0xF114
+#define MTS_MT9234ZBA_PRODUCT_ID 0xF115
+#define MTS_MT9234ZBAOLD_PRODUCT_ID 0x0319
+
+/* Abbott Diabetics vendor and product ids */
+#define ABBOTT_VENDOR_ID 0x1a61
+#define ABBOTT_STEREO_PLUG_ID 0x3410
+#define ABBOTT_PRODUCT_ID ABBOTT_STEREO_PLUG_ID
+#define ABBOTT_STRIP_PORT_ID 0x3420
+
+/* Honeywell vendor and product IDs */
+#define HONEYWELL_VENDOR_ID 0x10ac
+#define HONEYWELL_HGI80_PRODUCT_ID 0x0102 /* Honeywell HGI80 */
+
+/* Moxa UPORT 11x0 vendor and product IDs */
+#define MXU1_VENDOR_ID 0x110a
+#define MXU1_1110_PRODUCT_ID 0x1110
+#define MXU1_1130_PRODUCT_ID 0x1130
+#define MXU1_1150_PRODUCT_ID 0x1150
+#define MXU1_1151_PRODUCT_ID 0x1151
+#define MXU1_1131_PRODUCT_ID 0x1131
+
+/* Commands */
+#define TI_GET_VERSION 0x01
+#define TI_GET_PORT_STATUS 0x02
+#define TI_GET_PORT_DEV_INFO 0x03
+#define TI_GET_CONFIG 0x04
+#define TI_SET_CONFIG 0x05
+#define TI_OPEN_PORT 0x06
+#define TI_CLOSE_PORT 0x07
+#define TI_START_PORT 0x08
+#define TI_STOP_PORT 0x09
+#define TI_TEST_PORT 0x0A
+#define TI_PURGE_PORT 0x0B
+#define TI_RESET_EXT_DEVICE 0x0C
+#define TI_WRITE_DATA 0x80
+#define TI_READ_DATA 0x81
+#define TI_REQ_TYPE_CLASS 0x82
+
+/* Module identifiers */
+#define TI_I2C_PORT 0x01
+#define TI_IEEE1284_PORT 0x02
+#define TI_UART1_PORT 0x03
+#define TI_UART2_PORT 0x04
+#define TI_RAM_PORT 0x05
+
+/* Modem status */
+#define TI_MSR_DELTA_CTS 0x01
+#define TI_MSR_DELTA_DSR 0x02
+#define TI_MSR_DELTA_RI 0x04
+#define TI_MSR_DELTA_CD 0x08
+#define TI_MSR_CTS 0x10
+#define TI_MSR_DSR 0x20
+#define TI_MSR_RI 0x40
+#define TI_MSR_CD 0x80
+#define TI_MSR_DELTA_MASK 0x0F
+#define TI_MSR_MASK 0xF0
+
+/* Line status */
+#define TI_LSR_OVERRUN_ERROR 0x01
+#define TI_LSR_PARITY_ERROR 0x02
+#define TI_LSR_FRAMING_ERROR 0x04
+#define TI_LSR_BREAK 0x08
+#define TI_LSR_ERROR 0x0F
+#define TI_LSR_RX_FULL 0x10
+#define TI_LSR_TX_EMPTY 0x20
+
+/* Line control */
+#define TI_LCR_BREAK 0x40
+
+/* Modem control */
+#define TI_MCR_LOOP 0x04
+#define TI_MCR_DTR 0x10
+#define TI_MCR_RTS 0x20
+
+/* Mask settings */
+#define TI_UART_ENABLE_RTS_IN 0x0001
+#define TI_UART_DISABLE_RTS 0x0002
+#define TI_UART_ENABLE_PARITY_CHECKING 0x0008
+#define TI_UART_ENABLE_DSR_OUT 0x0010
+#define TI_UART_ENABLE_CTS_OUT 0x0020
+#define TI_UART_ENABLE_X_OUT 0x0040
+#define TI_UART_ENABLE_XA_OUT 0x0080
+#define TI_UART_ENABLE_X_IN 0x0100
+#define TI_UART_ENABLE_DTR_IN 0x0800
+#define TI_UART_DISABLE_DTR 0x1000
+#define TI_UART_ENABLE_MS_INTS 0x2000
+#define TI_UART_ENABLE_AUTO_START_DMA 0x4000
+
+/* Parity */
+#define TI_UART_NO_PARITY 0x00
+#define TI_UART_ODD_PARITY 0x01
+#define TI_UART_EVEN_PARITY 0x02
+#define TI_UART_MARK_PARITY 0x03
+#define TI_UART_SPACE_PARITY 0x04
+
+/* Stop bits */
+#define TI_UART_1_STOP_BITS 0x00
+#define TI_UART_1_5_STOP_BITS 0x01
+#define TI_UART_2_STOP_BITS 0x02
+
+/* Bits per character */
+#define TI_UART_5_DATA_BITS 0x00
+#define TI_UART_6_DATA_BITS 0x01
+#define TI_UART_7_DATA_BITS 0x02
+#define TI_UART_8_DATA_BITS 0x03
+
+/* 232/485 modes */
+#define TI_UART_232 0x00
+#define TI_UART_485_RECEIVER_DISABLED 0x01
+#define TI_UART_485_RECEIVER_ENABLED 0x02
+
+/* Pipe transfer mode and timeout */
+#define TI_PIPE_MODE_CONTINUOUS 0x01
+#define TI_PIPE_MODE_MASK 0x03
+#define TI_PIPE_TIMEOUT_MASK 0x7C
+#define TI_PIPE_TIMEOUT_ENABLE 0x80
+
+/* Config struct */
+struct ti_uart_config {
+ __u16 wBaudRate;
+ __u16 wFlags;
+ __u8 bDataBits;
+ __u8 bParity;
+ __u8 bStopBits;
+ char cXon;
+ char cXoff;
+ __u8 bUartMode;
+} __packed;
+
+/* Get port status */
+struct ti_port_status {
+ __u8 bCmdCode;
+ __u8 bModuleId;
+ __u8 bErrorCode;
+ __u8 bMSR;
+ __u8 bLSR;
+} __packed;
+
+/* Purge modes */
+#define TI_PURGE_OUTPUT 0x00
+#define TI_PURGE_INPUT 0x80
+
+/* Read/Write data */
+#define TI_RW_DATA_ADDR_SFR 0x10
+#define TI_RW_DATA_ADDR_IDATA 0x20
+#define TI_RW_DATA_ADDR_XDATA 0x30
+#define TI_RW_DATA_ADDR_CODE 0x40
+#define TI_RW_DATA_ADDR_GPIO 0x50
+#define TI_RW_DATA_ADDR_I2C 0x60
+#define TI_RW_DATA_ADDR_FLASH 0x70
+#define TI_RW_DATA_ADDR_DSP 0x80
+
+#define TI_RW_DATA_UNSPECIFIED 0x00
+#define TI_RW_DATA_BYTE 0x01
+#define TI_RW_DATA_WORD 0x02
+#define TI_RW_DATA_DOUBLE_WORD 0x04
+
+struct ti_write_data_bytes {
+ __u8 bAddrType;
+ __u8 bDataType;
+ __u8 bDataCounter;
+ __be16 wBaseAddrHi;
+ __be16 wBaseAddrLo;
+ __u8 bData[0];
+} __packed;
+
+struct ti_read_data_request {
+ __u8 bAddrType;
+ __u8 bDataType;
+ __u8 bDataCounter;
+ __be16 wBaseAddrHi;
+ __be16 wBaseAddrLo;
+} __packed;
+
+struct ti_read_data_bytes {
+ __u8 bCmdCode;
+ __u8 bModuleId;
+ __u8 bErrorCode;
+ __u8 bData[0];
+} __packed;
+
+/* Interrupt struct */
+struct ti_interrupt {
+ __u8 bICode;
+ __u8 bIInfo;
+} __packed;
+
+/* Interrupt codes */
+#define TI_GET_PORT_FROM_CODE(c) (((c) >> 4) - 3)
+#define TI_GET_FUNC_FROM_CODE(c) ((c) & 0x0f)
+#define TI_CODE_HARDWARE_ERROR 0xFF
+#define TI_CODE_DATA_ERROR 0x03
+#define TI_CODE_MODEM_STATUS 0x04
+
+/* Download firmware max packet size */
+#define TI_DOWNLOAD_MAX_PACKET_SIZE 64
+
+/* Firmware image header */
+struct ti_firmware_header {
+ __le16 wLength;
+ __u8 bCheckSum;
+} __packed;
+
+/* UART addresses */
+#define TI_UART1_BASE_ADDR 0xFFA0 /* UART 1 base address */
+#define TI_UART2_BASE_ADDR 0xFFB0 /* UART 2 base address */
+#define TI_UART_OFFSET_LCR 0x0002 /* UART MCR register offset */
+#define TI_UART_OFFSET_MCR 0x0004 /* UART MCR register offset */

#define TI_DRIVER_AUTHOR "Al Borchers <alborchers@xxxxxxxxxxxxxxxx>"
#define TI_DRIVER_DESC "TI USB 3410/5052 Serial Driver"
@@ -416,7 +649,7 @@ static int ti_open(struct tty_struct *tty, struct usb_serial_port *port)
struct urb *urb;
int port_number;
int status;
- __u16 open_settings = (__u8)(TI_PIPE_MODE_CONTINOUS |
+ __u16 open_settings = (__u8)(TI_PIPE_MODE_CONTINUOUS |
TI_PIPE_TIMEOUT_ENABLE |
(TI_TRANSFER_TIMEOUT << 2));

--
2.8.2