Re: [PATCH RFT 1/2] phylib: add device reset GPIO support

[Sergei Shtylyov]

Hello.

On 05/13/2016 12:35 AM, Sergei Shtylyov wrote:

> > [we already talked about this patch in #armlinux, I'm now just
> > forwarding my comments on the list. Background was that I sent an easier
> > and less complete patch with the same idea. See
> > http://patchwork.ozlabs.org/patch/621418/]
> >
> > [added Linus Walleij to Cc, there is a question for you/him below]
> >
> > On Fri, Apr 29, 2016 at 01:12:54AM +0300, Sergei Shtylyov wrote:
> > > --- net-next.orig/Documentation/devicetree/bindings/net/phy.txt
> > > +++ net-next/Documentation/devicetree/bindings/net/phy.txt
> > > @@ -35,6 +35,8 @@ Optional Properties:
> > >  - broken-turn-around: If set, indicates the PHY device does not correctly
> > >    release the turn around line low at the end of a MDIO transaction.
> > >
> > > +- reset-gpios: The GPIO phandle and specifier for the PHY reset signal.
> > > +
> > >  Example:
> > >
> > >  ethernet-phy@0 {
> >
> > This is great.
> >
> > > Index: net-next/drivers/net/phy/at803x.c
> > > ===================================================================
> > > --- net-next.orig/drivers/net/phy/at803x.c
> > > +++ net-next/drivers/net/phy/at803x.c
> > > @@ -65,7 +65,6 @@ MODULE_LICENSE("GPL");
> > > [...]
> >
> > My patch breaks this driver. I wasn't aware of it.
>
>    I tried to be as careful as I could but still it looks that I didn't
> succeed at that too...

   Hm, I'm starting to forget the vital details about my patch...

> [...]
> > > Index: net-next/drivers/net/phy/mdio_device.c
> > > ===================================================================
> > > --- net-next.orig/drivers/net/phy/mdio_device.c
> > > +++ net-next/drivers/net/phy/mdio_device.c
> [...]
> > > @@ -117,9 +126,16 @@ static int mdio_probe(struct device *dev
> > >      struct mdio_driver *mdiodrv = to_mdio_driver(drv);
> > >      int err = 0;
> > >
> > > -    if (mdiodrv->probe)
> > > +    if (mdiodrv->probe) {
> > > +        /* Deassert the reset signal */
> > > +        mdio_device_reset(mdiodev, 0);
> > > +
> > >          err = mdiodrv->probe(mdiodev);
> > >
> > > +        /* Assert the reset signal */
> > > +        mdio_device_reset(mdiodev, 1);
> >
> > I wonder if it's safe to do this in general. What if ->probe does
> > something with the phy that is lost by resetting but that is relied on
> > later?
>
>    Well, I thought that config_init() method is designed for that but indeed
> the LXT driver writes to BMCR in its probe() method and hence is broken.
> Thank you for noticing...

   It's broken even without my patch. The phylib will cause a PHY soft reset 
when attaching to the PHY device, so all BMCR programming dpone in the probe() 
method will be lost. My patch does make sense as is. Looks like I should also 
look into fixing lxt.c. Florian, what do you think?

[...]

MBR, Sergei