[PATCH v4 22/22] ARM: dts: exynos: Add RTC and I2C to Exynos5410
From: Krzysztof Kozlowski
Date: Sun May 15 2016 - 16:16:28 EST
Configure Exynos5410-specific properties of RTC, I2C and HSI2C nodes.
This still does not enable them on the board level though.
Signed-off-by: Krzysztof Kozlowski <krzk@xxxxxxxxxx>
Reviewed-by: Javier Martinez Canillas <javier@xxxxxxxxxxxxxxx>
---
arch/arm/boot/dts/exynos5410.dtsi | 63 +++++++++++++++++++++++++++++++++++++++
1 file changed, 63 insertions(+)
diff --git a/arch/arm/boot/dts/exynos5410.dtsi b/arch/arm/boot/dts/exynos5410.dtsi
index 37bd8d419c5d..46607d88cf53 100644
--- a/arch/arm/boot/dts/exynos5410.dtsi
+++ b/arch/arm/boot/dts/exynos5410.dtsi
@@ -146,6 +146,62 @@
};
};
+&i2c_0 {
+ clocks = <&clock CLK_I2C0>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_bus>;
+};
+
+&i2c_1 {
+ clocks = <&clock CLK_I2C1>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_bus>;
+};
+
+&i2c_2 {
+ clocks = <&clock CLK_I2C2>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_bus>;
+};
+
+&i2c_3 {
+ clocks = <&clock CLK_I2C3>;
+ clock-names = "i2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_bus>;
+};
+
+&hsi2c_4 {
+ clocks = <&clock CLK_USI0>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_hs_bus>;
+};
+
+&hsi2c_5 {
+ clocks = <&clock CLK_USI1>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_hs_bus>;
+};
+
+&hsi2c_6 {
+ clocks = <&clock CLK_USI2>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_hs_bus>;
+};
+
+&hsi2c_7 {
+ clocks = <&clock CLK_USI3>;
+ clock-names = "hsi2c";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c7_hs_bus>;
+};
+
&mct {
clocks = <&fin_pll>, <&clock CLK_MCT>;
clock-names = "fin_pll", "mct";
@@ -156,6 +212,13 @@
clock-names = "timers";
};
+&rtc {
+ clocks = <&clock CLK_RTC>;
+ clock-names = "rtc";
+ interrupt-parent = <&pmu_system_controller>;
+ status = "disabled";
+};
+
&serial_0 {
clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
clock-names = "uart", "clk_uart_baud0";
--
2.5.0