Re: [patch net-next 01/11] net: hisilicon: add support of acpi for hns-mdio

From: Yankejian (Hackim Yim)
Date: Mon May 16 2016 - 03:12:42 EST

Next message: Herbert Xu: "Crypto Update for 4.7"
Previous message: Peter Chen: "Re: [PATCH v8 13/14] usb: gadget: udc: adapt to OTG core"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On 2016/5/13 20:59, Andy Shevchenko wrote:
> On Fri, 2016-05-13 at 16:19 +0800, Yisen Zhuang wrote:
>> From: Kejian Yan <yankejian@xxxxxxxxxx>
>>
>> hns-mdio needs to register itself to mii-bus. The info of the device
>> can
>> be read by both OF and ACPI.
>> HNS tries to call Linux PHY driver to help access PHY-devices, the HNS
>> hardware topology is as below. The MDIO controller may control several
>> PHY-devices, and each PHY-device connects to a MAC device. The MDIO
>> will
>> be registered to mdiobus, then PHY-devices will register when each mac
>> find PHY device.
>> cpu
>> |
>> |
>> -------------------------------------------
>> | | |
>> | | |
>> | dsaf |
>> MDIO | MDIO
>> | --------------------------- |
>> | | | | | |
>> | | | | | |
>> | MAC MAC MAC MAC |
>> | | | | | |
>> ---- |-------- |-------- | | --------
>> || || || ||
>> PHY PHY PHY PHY
>>
>> And the driver can handle reset sequence by _DSD method in DSDT in
>> ACPI case.
>>
>> Signed-off-by: Kejian Yan <yankejian@xxxxxxxxxx>
>> Signed-off-by: Yisen Zhuang <Yisen.Zhuang@xxxxxxxxxx>
>> ---
>> drivers/net/ethernet/hisilicon/hns_mdio.c | 145 ++++++++++++++++++---
>> ---------
>> 1 file changed, 90 insertions(+), 55 deletions(-)
>>
>> diff --git a/drivers/net/ethernet/hisilicon/hns_mdio.c
>> b/drivers/net/ethernet/hisilicon/hns_mdio.c
>> index 765ddb3..4b779df 100644
>> --- a/drivers/net/ethernet/hisilicon/hns_mdio.c
>> +++ b/drivers/net/ethernet/hisilicon/hns_mdio.c
>> @@ -7,6 +7,7 @@
>> * (at your option) any later version.
>> */
>>
>> +#include <linux/acpi.h>
>> #include <linux/errno.h>
>> #include <linux/etherdevice.h>
>> #include <linux/init.h>
>> @@ -354,64 +355,72 @@ static int hns_mdio_reset(struct mii_bus *bus)
>> struct hns_mdio_device *mdio_dev = (struct hns_mdio_device
>> *)bus->priv;
>> int ret;
>>
>> - if (!mdio_dev->subctrl_vbase) {
>> - dev_err(&bus->dev, "mdio sys ctl reg has not
>> maped\n");
>> - return -ENODEV;
>> - }
>> -
>> - /*1. reset req, and read reset st check*/
>> - ret = mdio_sc_cfg_reg_write(mdio_dev, MDIO_SC_RESET_REQ, 0x1,
>> - MDIO_SC_RESET_ST, 0x1,
>> - MDIO_CHECK_SET_ST);
>> - if (ret) {
>> - dev_err(&bus->dev, "MDIO reset fail\n");
>> - return ret;
>> - }
>> + if (IS_ENABLED(CONFIG_OF) && bus->parent->of_node) {
> Can you keep indentation the same?
>
> Also I suggest to use struct fwnode_handle, and this will be something
> like
>
> if (is_of_node(...))
ok, thanks Andy. i will fix it in next submit

>
>> + if (!mdio_dev->subctrl_vbase) {
>> + dev_err(&bus->dev, "mdio sys ctl reg has not
>> maped\n");
>> + return -ENODEV;
>> + }
>>
>> - /*2. dis clk, and read clk st check*/
>> - ret = mdio_sc_cfg_reg_write(mdio_dev, MDIO_SC_CLK_DIS,
>> - 0x1, MDIO_SC_CLK_ST, 0x1,
>> - MDIO_CHECK_CLR_ST);
>> - if (ret) {
>> - dev_err(&bus->dev, "MDIO dis clk fail\n");
>> - return ret;
>> - }
>> + /*1. reset req, and read reset st check*/
>> + ret = mdio_sc_cfg_reg_write(mdio_dev,
>> MDIO_SC_RESET_REQ, 0x1,
>> + MDIO_SC_RESET_ST, 0x1,
>> + MDIO_CHECK_SET_ST);
>> + if (ret) {
>> + dev_err(&bus->dev, "MDIO reset fail\n");
>> + return ret;
>> + }
>>
>> - /*3. reset dreq, and read reset st check*/
>> - ret = mdio_sc_cfg_reg_write(mdio_dev, MDIO_SC_RESET_DREQ,
>> 0x1,
>> - MDIO_SC_RESET_ST, 0x1,
>> - MDIO_CHECK_CLR_ST);
>> - if (ret) {
>> - dev_err(&bus->dev, "MDIO dis clk fail\n");
>> - return ret;
>> - }
>> + /*2. dis clk, and read clk st check*/
>> + ret = mdio_sc_cfg_reg_write(mdio_dev,
>> MDIO_SC_CLK_DIS,
>> + 0x1, MDIO_SC_CLK_ST, 0x1,
>> + MDIO_CHECK_CLR_ST);
>> + if (ret) {
>> + dev_err(&bus->dev, "MDIO dis clk fail\n");
>> + return ret;
>> + }
>>
>> - /*4. en clk, and read clk st check*/
>> - ret = mdio_sc_cfg_reg_write(mdio_dev, MDIO_SC_CLK_EN,
>> - 0x1, MDIO_SC_CLK_ST, 0x1,
>> - MDIO_CHECK_SET_ST);
>> - if (ret)
>> - dev_err(&bus->dev, "MDIO en clk fail\n");
>> + /*3. reset dreq, and read reset st check*/
>> + ret = mdio_sc_cfg_reg_write(mdio_dev,
>> MDIO_SC_RESET_DREQ, 0x1,
>> + MDIO_SC_RESET_ST, 0x1,
>> + MDIO_CHECK_CLR_ST);
>> + if (ret) {
>> + dev_err(&bus->dev, "MDIO dis clk fail\n");
>> + return ret;
>> + }
>>
>> + /*4. en clk, and read clk st check*/
>> + ret = mdio_sc_cfg_reg_write(mdio_dev, MDIO_SC_CLK_EN,
>> + 0x1, MDIO_SC_CLK_ST, 0x1,
>> + MDIO_CHECK_SET_ST);
>> + if (ret)
>> + dev_err(&bus->dev, "MDIO en clk fail\n");
>> + } else if (ACPI_COMPANION(bus->parent)) {
>> + acpi_status s;
>> +
>> + s = acpi_evaluate_object(ACPI_HANDLE(bus->parent),
>> + "_RST", NULL, NULL);
>> + if (ACPI_FAILURE(s)) {
>> + dev_err(&bus->dev, "Reset failed,
>> return:%#x\n", s);
>> + ret = -EBUSY;
>> + } else {
>> + ret = 0;
>> + }
>> + } else {
>> + dev_err(&bus->dev, "cannot get cfd data from of or
>> acpi\n");
> cannot -> Can not
>
> WTF cfd?
>
> of or acpi -> DT or ACPI

ok, thanks Andy. i will fix it in next submit

>> + ret = -ENXIO;
>> + }
>> return ret;
>> }
>>
>> /**
>> * hns_mdio_bus_name - get mdio bus name
>> * @name: mdio bus name
>> - * @np: mdio device node pointer
>> + * @addr: mdio physical address
>> */
>> -static void hns_mdio_bus_name(char *name, struct device_node *np)
>> +static void hns_mdio_bus_name(char *name, phys_addr_t addr)
>> {
>> - const u32 *addr;
>> - u64 taddr = OF_BAD_ADDR;
>> -
>> - addr = of_get_address(np, 0, NULL, NULL);
>> - if (addr)
>> - taddr = of_translate_address(np, addr);
>> -
>> - snprintf(name, MII_BUS_ID_SIZE, "%s@%llx", np->name,
>> - (unsigned long long)taddr);
>> + snprintf(name, MII_BUS_ID_SIZE,
>> + "hns-mdio@%llx", (unsigned long long)addr);
>> }
>>
>> /**
>> @@ -422,7 +431,6 @@ static void hns_mdio_bus_name(char *name, struct
>> device_node *np)
>> */
>> static int hns_mdio_probe(struct platform_device *pdev)
>> {
>> - struct device_node *np;
>> struct hns_mdio_device *mdio_dev;
>> struct mii_bus *new_bus;
>> struct resource *res;
>> @@ -432,7 +440,7 @@ static int hns_mdio_probe(struct platform_device
>> *pdev)
>> dev_err(NULL, "pdev is NULL!\r\n");
>> return -ENODEV;
>> }
>> - np = pdev->dev.of_node;
>> +
>> mdio_dev = devm_kzalloc(&pdev->dev, sizeof(*mdio_dev),
>> GFP_KERNEL);
>> if (!mdio_dev)
>> return -ENOMEM;
>> @@ -448,7 +456,6 @@ static int hns_mdio_probe(struct platform_device
>> *pdev)
>> new_bus->write = hns_mdio_write;
>> new_bus->reset = hns_mdio_reset;
>> new_bus->priv = mdio_dev;
>> - hns_mdio_bus_name(new_bus->id, np);
>>
>> res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> mdio_dev->vbase = devm_ioremap_resource(&pdev->dev, res);
>> @@ -457,16 +464,37 @@ static int hns_mdio_probe(struct platform_device
>> *pdev)
>> return ret;
>> }
>>
>> - mdio_dev->subctrl_vbase =
>> - syscon_node_to_regmap(of_parse_phandle(np, "subctrl-
>> vbase", 0));
>> - if (IS_ERR(mdio_dev->subctrl_vbase)) {
>> - dev_warn(&pdev->dev, "no syscon hisilicon,peri-c-
>> subctrl\n");
>> - mdio_dev->subctrl_vbase = NULL;
>> + hns_mdio_bus_name(new_bus->id, res->start);
>> + if (IS_ENABLED(CONFIG_OF) && pdev->dev.of_node) {
> is_of_node()

ok, thanks Andy. i will fix it in next submit

>> + mdio_dev->subctrl_vbase = syscon_node_to_regmap(
>> + of_parse_phandle(pdev->dev.of_node,
>> + "subctrl-vbase", 0));
>> + if (IS_ERR(mdio_dev->subctrl_vbase)) {
>> + dev_warn(&pdev->dev, "no syscon
>> hisilicon,peri-c-subctrl\n");
>> + mdio_dev->subctrl_vbase = NULL;
>> + }
>> }
>> new_bus->parent = &pdev->dev;
>> platform_set_drvdata(pdev, new_bus);
>>
>> - ret = of_mdiobus_register(new_bus, np);
>> + if (IS_ENABLED(CONFIG_OF) && pdev->dev.of_node) {
> Ditto
>
>> + ret = of_mdiobus_register(new_bus, pdev-
>>> dev.of_node);
>> + } else if (ACPI_COMPANION(&pdev->dev)) {
> is_acpi_node()
>
>> + /* Clear all the IRQ properties */
>> + memset(new_bus->irq, PHY_POLL, 4 * PHY_MAX_ADDR);
>> +
>> + /* Mask out all PHYs from auto probing. */
>> + new_bus->phy_mask = ~0;
>> +
>> + /* Register the MDIO bus */
>> + ret = mdiobus_register(new_bus);
>> + if (ret)
>> + return ret;
>> + } else {
>> + dev_err(&pdev->dev, "cannot get cfd data from of or
>> acpi\n");
> Same as for previous message.
>
>> + return -ENXIO;
>> + }
>> +
>> if (ret) {
>> dev_err(&pdev->dev, "Cannot register as MDIO
>> bus!\n");
>> platform_set_drvdata(pdev, NULL);
>> @@ -499,12 +527,19 @@ static const struct of_device_id
>> hns_mdio_match[] = {
>> {}
>> };
>>
>> +static const struct acpi_device_id hns_mdio_acpi_match[] = {
>> + { "HISI0141", 0 },
>> + { },
>> +};
>> +MODULE_DEVICE_TABLE(acpi, hns_mdio_acpi_match);
>> +
>> static struct platform_driver hns_mdio_driver = {
>> .probe = hns_mdio_probe,
>> .remove = hns_mdio_remove,
>> .driver = {
>> .name = MDIO_DRV_NAME,
>> .of_match_table = hns_mdio_match,
>> + .acpi_match_table = ACPI_PTR(hns_mdio_acpi_match),
>> },
>> };
>>
>
> So, I suggest to split this to two logical changes:
>
> 1. Move to use fwnode_handle
> 2. Add ACPI bits

ok, thanks Andy. i will fix it in next submit

MBR,
Kejian

Next message: Herbert Xu: "Crypto Update for 4.7"
Previous message: Peter Chen: "Re: [PATCH v8 13/14] usb: gadget: udc: adapt to OTG core"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]