[PATCH 02/20] staging: comedi: plx9080.h: remove Power-Up Test Suite stuff

[Ian Abbott]

The defines related to the Power-Up Test Suite (PUTS) are just cruft that
has nothing to do with the PLX PCI-9080 chip.  They seem to have been
inherited from "drivers/net/plx9060.h" in the kernel 2.2.16 sources for
use by the "wanxl" driver.  Remove them.

Signed-off-by: Ian Abbott <abbotti@xxxxxxxxx>
---
 drivers/staging/comedi/drivers/plx9080.h | 120 -------------------------------
 1 file changed, 120 deletions(-)

diff --git a/drivers/staging/comedi/drivers/plx9080.h b/drivers/staging/comedi/drivers/plx9080.h
index 7d6311c..3759a19 100644
--- a/drivers/staging/comedi/drivers/plx9080.h
+++ b/drivers/staging/comedi/drivers/plx9080.h
@@ -294,126 +294,6 @@ enum bigend_bits {
 
 #define PLX_PREFETCH   32
 
-/*
- * The PCI Interface, via the PCI-9060 Chip, has up to eight (8) Mailbox
- * Registers.  The PUTS (Power-Up Test Suite) handles the board-side
- * interface/interaction using the first 4 registers.  Specifications for
- * the use of the full PUTS' command and status interface is contained
- * within a separate SBE PUTS Manual.  The Host-Side Device Driver only
- * uses a subset of the full PUTS interface.
- */
-
-/*****************************************/
-/***    MAILBOX #(-1) - MEM ACCESS STS ***/
-/*****************************************/
-
-#define MBX_STS_VALID      0x57584744	/* 'WXGD' */
-#define MBX_STS_DILAV      0x44475857	/* swapped = 'DGXW' */
-
-/*****************************************/
-/***    MAILBOX #0  -  PUTS STATUS     ***/
-/*****************************************/
-
-#define MBX_STS_MASK       0x000000ff	/* PUTS Status Register bits */
-#define MBX_STS_TMASK      0x0000000f	/* register bits for TEST number */
-
-#define MBX_STS_PCIRESET   0x00000100	/* Host issued PCI reset request */
-#define MBX_STS_BUSY       0x00000080	/* PUTS is in progress */
-#define MBX_STS_ERROR      0x00000040	/* PUTS has failed */
-/*
- * Undefined -> status in transition. We are in process of changing bits;
- * we SET Error bit before RESET of Busy bit
- */
-#define MBX_STS_RESERVED   0x000000c0
-
-#define MBX_RESERVED_5     0x00000020	/* FYI: reserved/unused bit */
-#define MBX_RESERVED_4     0x00000010	/* FYI: reserved/unused bit */
-
-/******************************************/
-/***    MAILBOX #1  -  PUTS COMMANDS    ***/
-/******************************************/
-
-/*
- * Any attempt to execute an unimplement command results in the PUTS
- * interface executing a NOOP and continuing as if the offending command
- * completed normally.  Note: this supplies a simple method to interrogate
- * mailbox command processing functionality.
- */
-
-#define MBX_CMD_MASK       0xffff0000	/* PUTS Command Register bits */
-
-#define MBX_CMD_ABORTJ     0x85000000	/* abort and jump */
-#define MBX_CMD_RESETP     0x86000000	/* reset and pause at start */
-#define MBX_CMD_PAUSE      0x87000000	/* pause immediately */
-#define MBX_CMD_PAUSEC     0x88000000	/* pause on completion */
-#define MBX_CMD_RESUME     0x89000000	/* resume operation */
-#define MBX_CMD_STEP       0x8a000000	/* single step tests */
-
-#define MBX_CMD_BSWAP      0x8c000000	/* identify byte swap scheme */
-#define MBX_CMD_BSWAP_0    0x8c000000	/* use scheme 0 */
-#define MBX_CMD_BSWAP_1    0x8c000001	/* use scheme 1 */
-
-/* setup host memory access window size */
-#define MBX_CMD_SETHMS     0x8d000000
-/* setup host memory access base address */
-#define MBX_CMD_SETHBA     0x8e000000
-/* perform memory setup and continue (IE. Done) */
-#define MBX_CMD_MGO        0x8f000000
-#define MBX_CMD_NOOP       0xFF000000	/* dummy, illegal command */
-
-/*****************************************/
-/***    MAILBOX #2  -  MEMORY SIZE     ***/
-/*****************************************/
-
-#define MBX_MEMSZ_MASK     0xffff0000	/* PUTS Memory Size Register bits */
-
-#define MBX_MEMSZ_128KB    0x00020000	/* 128 kilobyte board */
-#define MBX_MEMSZ_256KB    0x00040000	/* 256 kilobyte board */
-#define MBX_MEMSZ_512KB    0x00080000	/* 512 kilobyte board */
-#define MBX_MEMSZ_1MB      0x00100000	/* 1 megabyte board */
-#define MBX_MEMSZ_2MB      0x00200000	/* 2 megabyte board */
-#define MBX_MEMSZ_4MB      0x00400000	/* 4 megabyte board */
-#define MBX_MEMSZ_8MB      0x00800000	/* 8 megabyte board */
-#define MBX_MEMSZ_16MB     0x01000000	/* 16 megabyte board */
-
-/***************************************/
-/***    MAILBOX #2  -  BOARD TYPE    ***/
-/***************************************/
-
-#define MBX_BTYPE_MASK          0x0000ffff	/* PUTS Board Type Register */
-/* PUTS Board Family Register */
-#define MBX_BTYPE_FAMILY_MASK   0x0000ff00
-#define MBX_BTYPE_SUBTYPE_MASK  0x000000ff	/* PUTS Board Subtype */
-
-#define MBX_BTYPE_PLX9060       0x00000100	/* PLX family type */
-#define MBX_BTYPE_PLX9080       0x00000300	/* PLX wanXL100s family type */
-
-#define MBX_BTYPE_WANXL_4       0x00000104	/* wanXL400, 4-port */
-#define MBX_BTYPE_WANXL_2       0x00000102	/* wanXL200, 2-port */
-#define MBX_BTYPE_WANXL_1s      0x00000301	/* wanXL100s, 1-port */
-#define MBX_BTYPE_WANXL_1t      0x00000401	/* wanXL100T1, 1-port */
-
-/*****************************************/
-/***    MAILBOX #3  -  SHMQ MAILBOX    ***/
-/*****************************************/
-
-#define MBX_SMBX_MASK           0x000000ff	/* PUTS SHMQ Mailbox bits */
-
-/***************************************/
-/***    GENERIC HOST-SIDE DRIVER     ***/
-/***************************************/
-
-#define MBX_ERR    0
-#define MBX_OK     1
-
-/* mailbox check routine - type of testing */
-#define MBXCHK_STS      0x00	/* check for PUTS status */
-#define MBXCHK_NOWAIT   0x01	/* dont care about PUTS status */
-
-/* system allocates this many bytes for address mapping mailbox space */
-#define MBX_ADDR_SPACE_360 0x80	/* wanXL100s/200/400 */
-#define MBX_ADDR_MASK_360 (MBX_ADDR_SPACE_360 - 1)
-
 static inline int plx9080_abort_dma(void __iomem *iobase, unsigned int channel)
 {
 	void __iomem *dma_cs_addr;
-- 
2.8.1