[PATCH 12/20] staging: comedi: drivers: re-do PLX PCI 9080 CNTRL register values
From: Ian Abbott
Date: Fri May 20 2016 - 09:51:56 EST
Replace the existing macros in "plx9080.h" that define values for the
CNTRL register. Use the prefix `PLX_CNTRL_` for the macros. Make use
of the `BIT(x)` and `GENMASK(h,l)` macros to define the values.
Signed-off-by: Ian Abbott <abbotti@xxxxxxxxx>
---
drivers/staging/comedi/drivers/cb_pcidas64.c | 31 +++++++-------
drivers/staging/comedi/drivers/plx9080.h | 63 +++++++++++++++++++++-------
2 files changed, 65 insertions(+), 29 deletions(-)
diff --git a/drivers/staging/comedi/drivers/cb_pcidas64.c b/drivers/staging/comedi/drivers/cb_pcidas64.c
index 6b3f4dc..dfb2ae8 100644
--- a/drivers/staging/comedi/drivers/cb_pcidas64.c
+++ b/drivers/staging/comedi/drivers/cb_pcidas64.c
@@ -1614,7 +1614,7 @@ static const int i2c_low_udelay = 10;
static void i2c_set_sda(struct comedi_device *dev, int state)
{
struct pcidas64_private *devpriv = dev->private;
- static const int data_bit = CTL_EE_W;
+ static const int data_bit = PLX_CNTRL_EEWB;
void __iomem *plx_control_addr = devpriv->plx9080_iobase +
PLX_REG_CNTRL;
@@ -1635,7 +1635,7 @@ static void i2c_set_sda(struct comedi_device *dev, int state)
static void i2c_set_scl(struct comedi_device *dev, int state)
{
struct pcidas64_private *devpriv = dev->private;
- static const int clock_bit = CTL_USERO;
+ static const int clock_bit = PLX_CNTRL_USERO;
void __iomem *plx_control_addr = devpriv->plx9080_iobase +
PLX_REG_CNTRL;
@@ -1708,7 +1708,7 @@ static void i2c_write(struct comedi_device *dev, unsigned int address,
*/
/* make sure we dont send anything to eeprom */
- devpriv->plx_control_bits &= ~CTL_EE_CS;
+ devpriv->plx_control_bits &= ~PLX_CNTRL_EECS;
i2c_stop(dev);
i2c_start(dev);
@@ -3717,13 +3717,13 @@ static uint16_t read_eeprom(struct comedi_device *dev, uint8_t address)
static const int eeprom_udelay = 1;
udelay(eeprom_udelay);
- devpriv->plx_control_bits &= ~CTL_EE_CLK & ~CTL_EE_CS;
+ devpriv->plx_control_bits &= ~PLX_CNTRL_EESK & ~PLX_CNTRL_EECS;
/* make sure we don't send anything to the i2c bus on 4020 */
- devpriv->plx_control_bits |= CTL_USERO;
+ devpriv->plx_control_bits |= PLX_CNTRL_USERO;
writel(devpriv->plx_control_bits, plx_control_addr);
/* activate serial eeprom */
udelay(eeprom_udelay);
- devpriv->plx_control_bits |= CTL_EE_CS;
+ devpriv->plx_control_bits |= PLX_CNTRL_EECS;
writel(devpriv->plx_control_bits, plx_control_addr);
/* write read command and desired memory address */
@@ -3731,16 +3731,16 @@ static uint16_t read_eeprom(struct comedi_device *dev, uint8_t address)
/* set bit to be written */
udelay(eeprom_udelay);
if (bitstream & bit)
- devpriv->plx_control_bits |= CTL_EE_W;
+ devpriv->plx_control_bits |= PLX_CNTRL_EEWB;
else
- devpriv->plx_control_bits &= ~CTL_EE_W;
+ devpriv->plx_control_bits &= ~PLX_CNTRL_EEWB;
writel(devpriv->plx_control_bits, plx_control_addr);
/* clock in bit */
udelay(eeprom_udelay);
- devpriv->plx_control_bits |= CTL_EE_CLK;
+ devpriv->plx_control_bits |= PLX_CNTRL_EESK;
writel(devpriv->plx_control_bits, plx_control_addr);
udelay(eeprom_udelay);
- devpriv->plx_control_bits &= ~CTL_EE_CLK;
+ devpriv->plx_control_bits &= ~PLX_CNTRL_EESK;
writel(devpriv->plx_control_bits, plx_control_addr);
}
/* read back value from eeprom memory location */
@@ -3748,19 +3748,19 @@ static uint16_t read_eeprom(struct comedi_device *dev, uint8_t address)
for (bit = 1 << (value_length - 1); bit; bit >>= 1) {
/* clock out bit */
udelay(eeprom_udelay);
- devpriv->plx_control_bits |= CTL_EE_CLK;
+ devpriv->plx_control_bits |= PLX_CNTRL_EESK;
writel(devpriv->plx_control_bits, plx_control_addr);
udelay(eeprom_udelay);
- devpriv->plx_control_bits &= ~CTL_EE_CLK;
+ devpriv->plx_control_bits &= ~PLX_CNTRL_EESK;
writel(devpriv->plx_control_bits, plx_control_addr);
udelay(eeprom_udelay);
- if (readl(plx_control_addr) & CTL_EE_R)
+ if (readl(plx_control_addr) & PLX_CNTRL_EERB)
value |= bit;
}
/* deactivate eeprom serial input */
udelay(eeprom_udelay);
- devpriv->plx_control_bits &= ~CTL_EE_CS;
+ devpriv->plx_control_bits &= ~PLX_CNTRL_EECS;
writel(devpriv->plx_control_bits, plx_control_addr);
return value;
@@ -3948,7 +3948,8 @@ static int setup_subdevices(struct comedi_device *dev)
/* serial EEPROM, if present */
s = &dev->subdevices[8];
- if (readl(devpriv->plx9080_iobase + PLX_REG_CNTRL) & CTL_EECHK) {
+ if (readl(devpriv->plx9080_iobase + PLX_REG_CNTRL) &
+ PLX_CNTRL_EEPRESENT) {
s->type = COMEDI_SUBD_MEMORY;
s->subdev_flags = SDF_READABLE | SDF_INTERNAL;
s->n_chan = 128;
diff --git a/drivers/staging/comedi/drivers/plx9080.h b/drivers/staging/comedi/drivers/plx9080.h
index e9f1b9c..4ad9464 100644
--- a/drivers/staging/comedi/drivers/plx9080.h
+++ b/drivers/staging/comedi/drivers/plx9080.h
@@ -393,20 +393,55 @@ struct plx_dma_desc {
*/
#define PLX_REG_CNTRL 0x006c
-#define CTL_RDMA 0x0000000E /* DMA Read Command */
-#define CTL_WDMA 0x00000070 /* DMA Write Command */
-#define CTL_RMEM 0x00000600 /* Memory Read Command */
-#define CTL_WMEM 0x00007000 /* Memory Write Command */
-#define CTL_USERO 0x00010000 /* USERO output pin control bit */
-#define CTL_USERI 0x00020000 /* USERI input pin bit */
-#define CTL_EE_CLK 0x01000000 /* EEPROM Clock line */
-#define CTL_EE_CS 0x02000000 /* EEPROM Chip Select */
-#define CTL_EE_W 0x04000000 /* EEPROM Write bit */
-#define CTL_EE_R 0x08000000 /* EEPROM Read bit */
-#define CTL_EECHK 0x10000000 /* EEPROM Present bit */
-#define CTL_EERLD 0x20000000 /* EEPROM Reload Register */
-#define CTL_RESET 0x40000000 /* !! Adapter Reset !! */
-#define CTL_READY 0x80000000 /* Local Init Done */
+/* PCI Read Command Code For DMA */
+#define PLX_CNTRL_CCRDMA(x) (BIT(0) * ((x) & 0xf))
+#define PLX_CNTRL_CCRDMA_MASK GENMASK(3, 0)
+#define PLX_CNTRL_CCRDMA_SHIFT 0
+#define PLX_CNTRL_CCRDMA_NORMAL PLX_CNTRL_CCRDMA(14) /* value after reset */
+/* PCI Write Command Code For DMA 0 */
+#define PLX_CNTRL_CCWDMA(x) (BIT(4) * ((x) & 0xf))
+#define PLX_CNTRL_CCWDMA_MASK GENMASK(7, 4)
+#define PLX_CNTRL_CCWDMA_SHIFT 4
+#define PLX_CNTRL_CCWDMA_NORMAL PLX_CNTRL_CCWDMA(7) /* value after reset */
+/* PCI Memory Read Command Code For Direct Master */
+#define PLX_CNTRL_CCRDM(x) (BIT(8) * ((x) & 0xf))
+#define PLX_CNTRL_CCRDM_MASK GENMASK(11, 8)
+#define PLX_CNTRL_CCRDM_SHIFT 8
+#define PLX_CNTRL_CCRDM_NORMAL PLX_CNTRL_CCRDM(6) /* value after reset */
+/* PCI Memory Write Command Code For Direct Master */
+#define PLX_CNTRL_CCWDM(x) (BIT(12) * ((x) & 0xf))
+#define PLX_CNTRL_CCWDM_MASK GENMASK(15, 12)
+#define PLX_CNTRL_CCWDM_SHIFT 12
+#define PLX_CNTRL_CCWDM_NORMAL PLX_CNTRL_CCWDM(7) /* value after reset */
+/* General Purpose Output (USERO) */
+#define PLX_CNTRL_USERO BIT(16)
+/* General Purpose Input (USERI) (read-only) */
+#define PLX_CNTRL_USERI BIT(17)
+/* Serial EEPROM Clock Output (EESK) */
+#define PLX_CNTRL_EESK BIT(24)
+/* Serial EEPROM Chip Select Output (EECS) */
+#define PLX_CNTRL_EECS BIT(25)
+/* Serial EEPROM Data Write Bit (EEDI (sic)) */
+#define PLX_CNTRL_EEWB BIT(26)
+/* Serial EEPROM Data Read Bit (EEDO (sic)) (read-only) */
+#define PLX_CNTRL_EERB BIT(27)
+/* Serial EEPROM Present (read-only) */
+#define PLX_CNTRL_EEPRESENT BIT(28)
+/* Reload Configuration Registers from EEPROM */
+#define PLX_CNTRL_EERELOAD BIT(29)
+/* PCI Adapter Software Reset (asserts LRESETo#) */
+#define PLX_CNTRL_RESET BIT(30)
+/* Local Init Status (read-only) */
+#define PLX_CNTRL_INITDONE BIT(31)
+/*
+ * Combined command code stuff for convenience.
+ */
+#define PLX_CNTRL_CC_MASK \
+ (PLX_CNTRL_CCRDMA_MASK | PLX_CNTRL_CCWDMA_MASK | \
+ PLX_CNTRL_CCRDM_MASK | PLX_CNTRL_CCWDM_MASK)
+#define PLX_CNTRL_CC_NORMAL \
+ (PLX_CNTRL_CCRDMA_NORMAL | PLX_CNTRL_CCWDMA_NORMAL | \
+ PLX_CNTRL_CCRDM_NORMAL | PLX_CNTRL_CCWDM_NORMAL) /* val after reset */
/* PCI Permanent Configuration ID Register (hard-coded PLX vendor and device) */
#define PLX_REG_PCIHIDR 0x0070
--
2.8.1