Re: [PATCH V2 3/5] Documentation/devicetree/bindings: b850v3_lvds_dp

[Javier Martinez Canillas]

Hello Peter,

On Thu, Jun 9, 2016 at 12:25 PM, Peter Senna Tschudin
<peter.senna@xxxxxxxxxxxxx> wrote:
> Devicetree bindings documentation for the GE B850v3 LVDS/DP++
> display bridge.
>
> Cc: Enric Balletbo i Serra <enric.balletbo@xxxxxxxxxxxxx>
> Cc: Philipp Zabel <p.zabel@xxxxxxxxxxxxxx>
> Cc: Rob Herring <robh@xxxxxxxxxx>
> Cc: Fabio Estevam <fabio.estevam@xxxxxxx>
> Signed-off-by: Peter Senna Tschudin <peter.senna@xxxxxxxxxxxxx>
> ---
> Changes from V1:
>  - Replaced '_' by '-' in node names or compatible strings
>  - Added missing @73 to the example
>
>  .../devicetree/bindings/ge/b850v3_lvds_dp.txt      | 38 ++++++++++++++++++++++
>  1 file changed, 38 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/ge/b850v3_lvds_dp.txt
>
> diff --git a/Documentation/devicetree/bindings/ge/b850v3_lvds_dp.txt b/Documentation/devicetree/bindings/ge/b850v3_lvds_dp.txt
> new file mode 100644
> index 0000000..46bbea9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/ge/b850v3_lvds_dp.txt
> @@ -0,0 +1,38 @@
> +Driver for GE B850v3 LVDS/DP++ display bridge
> +
> +Required properties:
> +  - compatible : should be "ge,b850v3_lvds_dp".

It seems you forgot to replace '_' by '-' (you did in the example though)

> +  - reg : should contain the address used to ack the interrupts.
> +  - interrupt-parent : should link to the gpio used as interrupt
> +    source on the host.

Is the interrupt parent always a GPIO controller since that is what
this description says.

Shouldn't be instead something like instead?

interrupt-parent: phandle of the interrupt controller that services
interrupts to the device

> +  - interrupts : one interrupt should be described here, as in
> +    <0 IRQ_TYPE_LEVEL_HIGH>.
> +  - edid-reg : should contain the address used to read edid information
> +  - port : should describe the vide signal connection between the host

s/vide/video

> +    and the bridge.
> +
> +Example:
> +
> +&mux2_i2c2 {
> +       status = "okay";
> +       clock-frequency = <100000>;
> +
> +       b850v3-lvds-dp-bridge@73  {
> +               compatible = "ge,b850v3-lvds-dp";
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               reg = <0x73>;
> +               interrupt-parent = <&gpio2>;
> +               interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
> +
> +               edid-reg = <0x72>;
> +
> +               port@0 {
> +                       reg = <0>;

AFAIU a unit-address and reg property for ports are only needed if you
have more than one port according to
Documentation/devicetree/bindings/graph.txt and
Documentation/devicetree/bindings/media/video-interfaces.txt.

> +                       b850v3_dp_bridge_in: endpoint {
> +                               remote-endpoint = <&lvds0_out>;
> +                       };
> +               };
> +       };
> +};
> --

Best regards,
Javier