Re: [PATCH 01/11] phy: rockchip-emmc: Increase lock time allowance

[Doug Anderson]

Shawn,

On Mon, Jun 13, 2016 at 12:58 AM, Shawn Lin <shawn.lin@xxxxxxxxxxxxxx> wrote:
> On 2016/6/8 6:44, Douglas Anderson wrote:
>>
>> Previous PHY code waited a fixed amount of time for the DLL to lock at
>> power on time.  Unfortunately, the time for the DLL to lock is actually
>> a bit more dynamic and can be longer if the card clock is slower.
>>
>> Instead of waiting a fixed 30 us, let's now dynamically wait until the
>> lock bit gets set.  We'll wait up to 10 ms which should be OK even if
>> the card clock is at the super slow 100 kHz.
>>
>
> mmc stack limit the min freq to 200k when initializing the card.

Are you certain?  In "drivers/mmc/core/core.c" I see:

static const unsigned freqs[] = { 400000, 300000, 200000, 100000 };

In ID mode if 400kHz, 300kHz, 200kHz all fail then it will try 100kHz.


> So 5ms is enough, but it's ok to set the max timeout to 10ms as we
> can break out if locked.

Right, it's OK to error on the long side since it is really a pretty
serious error if the DLL doesn't lock and delaying tens of
milliseconds in this case is not a huge deal.


>> On its own, this change makes the PHY power on code a little more
>> robust.  Before this change the PHY was relying on the eMMC code to make
>> sure the PHY was only powered on when the card clock was set to at least
>> 50 MHz before, though this reliance wasn't documented anywhere.
>>
>> This change will be even more useful in future changes where we actually
>> need to be able to wait for a DLL lock at slower clock speeds.
>>
>> Signed-off-by: Douglas Anderson <dianders@xxxxxxxxxxxx>
>> ---
>>  drivers/phy/phy-rockchip-emmc.c | 27 +++++++++++++++++++--------
>>  1 file changed, 19 insertions(+), 8 deletions(-)
>>
>> diff --git a/drivers/phy/phy-rockchip-emmc.c
>> b/drivers/phy/phy-rockchip-emmc.c
>> index a69f53630e67..8336053aea5c 100644
>> --- a/drivers/phy/phy-rockchip-emmc.c
>> +++ b/drivers/phy/phy-rockchip-emmc.c
>> @@ -85,6 +85,7 @@ static int rockchip_emmc_phy_power(struct
>> rockchip_emmc_phy *rk_phy,
>>  {
>>         unsigned int caldone;
>>         unsigned int dllrdy;
>> +       unsigned long timeout;
>>
>>         /*
>>          * Keep phyctrl_pdb and phyctrl_endll low to allow
>> @@ -137,15 +138,25 @@ static int rockchip_emmc_phy_power(struct
>> rockchip_emmc_phy *rk_phy,
>>                                    PHYCTRL_ENDLL_MASK,
>>                                    PHYCTRL_ENDLL_SHIFT));
>>         /*
>> -        * After enable analog DLL circuits, we need an extra 10.2us
>> -        * for dll to be ready for work. But according to testing, we
>> -        * find some chips need more than 25us.
>> +        * After enabling analog DLL circuits docs say that we need 10.2
>> us if
>> +        * our source clock is at 50 MHz and that lock time scales
>> linearly
>> +        * with clock speed.  If we are powering on the PHY and the card
>> clock
>> +        * is super slow (like 100 kHZ) this could take as long as 5.1 ms.
>
>
> 5.1ms is by calculation or test?

By calculation.

>>> 10.2 us * (50000000 Hz / 100000 Hz)
5100.0 us, or 5.1 ms

I'll add clarification to the comment.


-Doug