Re: [v2 PATCH 1/4] Documentation: bindings: add dt doc for Rockchip USB Type-C PHY
From: Tomasz Figa
Date: Thu Jun 16 2016 - 03:50:10 EST
On Thu, Jun 16, 2016 at 9:31 AM, Chris Zhong <zyw@xxxxxxxxxxxxxx> wrote:
> Hi Heiko
>
>
> On 06/16/2016 06:11 AM, Heiko Stuebner wrote:
>>
>> Am Montag, 13. Juni 2016, 17:39:46 schrieb Chris Zhong:
>>>
>>> This patch adds a binding that describes the Rockchip USB Type-C PHY
>>> for rk3399
>>>
>>> Signed-off-by: Chris Zhong <zyw@xxxxxxxxxxxxxx>
>>>
>>> ---
>>>
>>> Changes in v2:
>>> - add some registers description
>>>
>>> Changes in v1:
>>> - add extcon node description
>>> - move the registers in phy driver
>>> - remove the suffix of reset
>>>
>>> .../devicetree/bindings/phy/phy-rockchip-typec.txt | 77
>>> ++++++++++++++++++++++ 1 file changed, 77 insertions(+)
>>> create mode 100644
>>> Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
>>> b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt new file
>>> mode 100644
>>> index 0000000..430920c
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
>>> @@ -0,0 +1,77 @@
>>> +* ROCKCHIP type-c PHY
>>> +---------------------
>>> +
>>> +Required properties:
>>> + - compatible : should be "rockchip,rk3399-typec-phy0" or
>>> + "rockchip,rk3399-typec-phy1"
>>> + - reg: Address and length of the usb phy control register set
>>> + - rockchip,grf : phandle to the syscon managing the "general
>>> + register files"
>>> + - clocks : phandle + clock specifier for the phy clocks
>>> + - clock-names : string, clock name, must be "tcpdcore", "tcpdphy_ref";
>>> + - resets : a list of phandle + reset specifier pairs
>>> + - reset-names : string reset name, must be:
>>> + "tcphy", "tcphy_pipe", "uphy_tcphy"
>>> + - #phy-cells : Must be 0. See ./phy-bindings.txt for details.
>>> + - extcon : extcon specifier for the Power Delivery
>>> +
>>> +Note, there are 2 type-c phys for RK3399, and they are almost identical,
>>> except +these registers(description below), every register node contains
>>> 3 sections: +offset, enable bit, write mask bit.
>>> + - rockchip,typec_conn_dir : the register of type-c connector direction,
>>> + for type-c phy0, it must be <0xe580 0 16>;
>>> + for type-c phy1, it must be <0xe58c 0 16>;
>>
>> I think I said this already, but these register-lists would be much
>> happier
>> being defined inside the driver - see how Frank managed this on his
>> usb2phy
>> please.
>>
>> Heiko
>>
> Yes, I move them into driver in v1 patch, but Rob Herring and Guenter Roeck
> recommend to put them back to dts.
> These phy0 and phy1 are exactly the same, except these grf registers.
I think having the registers in dts isn't a bad idea. It might be
actually even useful to bring up this PHY on new SoCs, if they happen
to have the same PHY, just different plumbing.
But I suppose we don't need two separate compatible strings for phy0
and phy1 anymore as Rob pointed, just one "rockchip,rk3399-typec-phy".
After the above is fixed and underscores in property names are
replaced with dashes, feel free to add my Reviewed-by.
Best regards,
Tomasz