Re: [PATCH 0/5] sched/debug: decouple sched_stat tracepoints from CONFIG_SCHEDSTATS

[Josh Poimboeuf]

On Wed, Jun 29, 2016 at 12:29:58PM +0200, Peter Zijlstra wrote:
> On Tue, Jun 28, 2016 at 02:43:36PM +0200, Peter Zijlstra wrote:
> 
> > Yeah, its a bit of a pain in general...
> > 
> > A) perf stat --null --repeat 50 -- perf bench sched messaging -g 50 -l 5000 | grep "seconds time elapsed"
> > B) perf stat --null --repeat 50 -- taskset 1 perf bench sched pipe | grep "seconds time elapsed"
> > 
> > 1) tip/master + 1-4
> > 2) tip/master + 1-5
> > 3) tip/master + 1-5 + below
> > 
> > 	1		2		3
> > 
> > A)	4.627767855	4.650429917	4.646208062
> > 	4.633921933	4.641424424	4.612021058
> > 	4.649536375	4.663144144	4.636815948
> > 	4.630165619	4.649053552	4.613022902
> > 
> > B)	1.770732957	1.789534273	1.773334291
> > 	1.761740716	1.795618428	1.773338681
> > 	1.763761666	1.822316496	1.774385589
> > 
> > 
> > From this it looks like patch 5 does hurt a wee bit, but we can get most
> > of that back by reordering the structure a bit. The results seem
> > 'stable' across rebuilds and reboots (I've pop'ed all patches and
> > rebuild, rebooted and re-benched 1 at the end and obtained similar
> > results).
> 
> Ha! So those numbers were with CONFIG_SCHEDSTAT=n :-/
> 
> 1) above 1 (4 patches, CONFIG_SCHEDSTAT=n, sysctl=0)
> 2) 1 + CONFIG_SCHEDSTAT=y (sysctl=0)
> 3) 2 + sysctl=1
> 4) above 3 (6 patches) + CONFIG_SCHEDSTAT=y (sysctl=0)
> 
> 
> 	1		2		3		4
> 
> A)	4.620495664	4.788352823	4.862036428	4.623480512
> 	4.628800053	4.792622881	4.855325525	4.613553872
> 	4.611909507	4.794282178	4.850959761	4.613323142
> 	4.608379522	4.787300153	4.822439864	4.597903070
> 
> B)	1.765668026	1.788374847	1.877803100	1.827213170
> 	1.769379968	1.779881911	1.870091005	1.825335322
> 	1.765822150	1.786251610	1.885874745	1.828218761
> 
> 
> Which looks good for hackbench, but still stinks for pipetest :/

I tried again on another system (Broadwell 2*10*2) and seemingly got
more consistent results, but the conclusions are a bit different from
yours.

I tested only with CONFIG_SCHEDSTAT=y, sysctl=0, because I think that
should be the most common configuration by far.

1) linus/master
2) linus/master + 1-4
3) linux/master + 1-5
4) linus/master + 1-5 + smp cacheline patch

A) perf stat --null --repeat 50 -- perf bench sched messaging -g 50 -l 5000
B) perf stat --null --repeat 50 -- taskset 1 perf bench sched pipe

	1		2		3		4

A)	6.335625627	6.299825679	6.317633969	6.305548464
	6.334188492	6.331391159	6.345195048	6.334608006
	6.345243359	6.329650737	6.328263309	6.304355127
	6.333154970	6.313859694	6.336338820	6.342374680

B)	2.310476138	2.324716175	2.355990033	2.350834083
	2.307231831	2.327946052	2.349816680	2.335581939
	2.303859470	2.317300965	2.347193526	2.333758084
	2.317224538	2.331390610	2.326164933	2.334235895

With patches 1-4, hackbench was slightly better and pipetest was
slightly worse.

With patches 1-5, hackbench was about the same or even slightly better
than baseline, and pipetest was 1-2% worse than baseline.

With your smp cacheline patch added, I didn't see a clear improvement.

It would be nice to have the schedstat tracepoints be always functional,
but I suppose it's up to you and Ingo as to whether it's worth the
performance tradeoff.

Another option would be to only merge patches 1-4.

-- 
Josh